Study guide

11.8 Counters, Prescalers, BCD & Data Converters

FCC General Radiotelephone Operator License GROL

Track your progress as you read

Finished sections get a check mark.

1 Introduction & GROL Exam Overview

1.1 About the General Radiotelephone Operator License 1.2 Exam Format, COLEMs, FRN & Application Process

2 Element 1: Rules & Regulations

2.1 Equipment Requirements (Part 80) 2.2 License Requirements & Operator Authority 2.3 Watchkeeping & Logkeeping Duties 2.4 Log Entries & Required Records 2.5 Ship Station Control, Inspections & International Rules

3 Element 1: Communications Procedures

3.1 Bridge-to-Bridge Operations & VTS 3.2 Distress Communications & Alerting 3.3 Operating Procedures, Calling & Testing 3.4 Urgency (PAN PAN) & Safety (SECURITE) Traffic 3.5 The GMDSS Concept & Ship Responsibilities

4 Element 1: Equipment Operations

4.1 VHF Equipment Controls 4.2 MF/HF SSB Equipment Controls 4.3 DSC Operations & Equipment Faults 4.4 VHF Channel Selection & Channel Assignments 4.5 MF/HF Frequency & Emission Selection 4.6 Required Equipment Tests & On-Air Test Procedure

5 Element 1: Other Equipment & Antennas

5.1 Marine Antennas & Polarization 5.2 EPIRBs & Emergency Beacons 5.3 Power Sources, Reserve Power & Required Tests 5.4 Search and Rescue Transponders (SARTs) 5.5 Survival Craft Portable VHF (SCT) Requirements 5.6 NAVTEX & Maritime Safety Information

6 Element 3: Electrical Principles

6.1 Electrical Elements, Units & Power Types 6.2 Magnetism & Magnetic Circuits 6.3 Resistance, Capacitance & Inductance 6.4 Waveforms & Semiconductor Introduction 6.5 Materials, Corrosion & Skin Effect 6.6 AC Measurement & Conversion Factors 6.7 Conduction, Reactive Power & Maximum Power Transfer

7 Element 3: Electrical Math

7.1 Ohm's Law — Series & Parallel Circuits 7.2 Frequency, Period, Wavelength & Waveform Math 7.3 Power Relationships & Decibels 7.4 RC/RL Time Constants 7.5 Frequency Counter Accuracy, PPM & Harmonics 7.6 Impedance in Rectangular & Polar Coordinates 7.7 Regulation, Turns Ratio, Zener Bias & Conductance

8 Element 3: Circuit Components — Passives & Power Devices

8.1 Capacitors & Photoconductive Devices 8.2 Transformers, Voltage Regulators & Zener Diodes 8.3 Diodes, SCRs & Triacs

9 Element 3: Active Components — Transistors & Devices

9.1 Bipolar Junction Transistors 9.2 FETs, LEDs & Specialty Devices 9.3 Device Selection, Ratings & Thermal Design

10 Element 3: Practical Circuits — RLC, Op Amps & Schematics

10.1 R-L-C Resonant Circuits 10.2 Op Amps, PLLs, VCOs & Mixers 10.3 Reading Schematics & Signal Flow

11 Element 3: Digital Logic

11.1 Logic Gates & Boolean Functions 11.2 Flip-Flops & Sequential Elements 11.3 Multivibrators & Timing Circuits 11.4 Microprocessors & Bus Architecture 11.5 TTL Logic Families & Input Voltage Levels 11.6 Positive & Negative Logic and Truth Tables 11.7 Memory Types & Microprocessor Concepts 11.8 Counters, Prescalers, BCD & Data Converters

12 Element 3: Receivers

12.1 Receiver Theory & Superheterodyne Architecture 12.2 RF Amplifiers & Front-End Design 12.3 Filters & Detectors 12.4 Audio, Squelch & Receiver Performance Specs 12.5 Receiver Oscillators: Colpitts, Hartley & Pierce 12.6 Mixing, Image Frequencies & Spurious Products 12.7 IF Selectivity & Filter Bandwidth

13 Element 3: Transmitters

13.1 RF Amplifier Classes & Efficiency 13.2 Oscillators, Modulators & Tuning Networks 13.3 SSB Transmitters & Modern Transmitter Technology

14 Element 3: Signals, Emissions & Modulation

14.1 Amplitude & Frequency Modulation 14.2 Single-Sideband Modulation 14.3 Pulse Modulation & Emission Types

15 Element 3: Power Sources

15.1 Batteries & Energy Storage 15.2 Motors, Generators & Power Supplies

16 Element 3: Antennas & Feed Lines

16.1 Antenna Theory, Types & Patterns 16.2 Voltage, Current & Impedance on Antennas 16.3 Transmission Lines, Velocity Factor & SWR 16.4 Effective Radiated Power & Antenna Bandwidth

17 Element 3 Background: Propagation & Radio Practice

17.1 Radio Wave Propagation Modes 17.2 Multipath, Fading & Doppler Effects 17.3 Radio Practice, Interference & Good Engineering

18 Element 3: Aircraft Radio Navigation Systems

18.1 DME & VOR 18.2 ILS, ADF & ATC Transponders 18.3 Aircraft Antennas, Frequencies & Equipment Functions

19 Element 3: Installation, Maintenance & Repair

19.1 Indicating Meters & Meter Movements 19.2 Oscilloscopes & Waveform Measurement 19.3 Measurement Procedures 19.4 Installation Codes & Bonding Procedures 19.5 Frequency Standards, SINAD Meters & EMI Hunting 19.6 Spectrum Analyzers, TDRs & Service Monitors 19.7 Bench Repair Practices, ESD & Rework Tools 19.8 Systematic Troubleshooting & Field Fault Diagnosis

20 Element 3: Communications Technology & Marine Systems

20.1 Transmission Types, Coding & Multiplexing 20.2 Signal Processing, Software & Codes 20.3 Marine VHF, MF/HF & SSB-SITOR 20.4 Survival Craft Electronics, FAX & NAVTEX 20.5 NMEA 0183 & NMEA 2000 Data Networks

21 Element 3: RADAR & Satellite Systems

21.1 RADAR Theory & Pulse Fundamentals 21.2 Range, Pulse Width & PRF 21.3 Radar Antennas & Waveguides 21.4 INMARSAT Satellite Communications 21.5 RADAR Components: Magnetron, Duplexer, ATR & Synchro 21.6 RADAR Equipment, ARPA & Radiation Safety 21.7 Low Earth Orbit Systems: Iridium & COSPAS-SARSAT 21.8 GPS Satellite Navigation & DGPS

22 Element 3: RF & Electrical Safety

22.1 RF Radiation Exposure Limits 22.2 Electrical Safety Practices for Radio Technicians

23 Study Strategy & Exam Day

23.1 Study Strategy, Practice Plan & Exam Day

11.8 Counters, Prescalers, BCD & Data Converters

Key Takeaways Explain This Topic AI

A prescaler divides an HF signal so that a low-frequency counter can display the operating frequency

A decade counter produces one output pulse for every ten input pulses

BCD means binary coded decimal, in which each decimal digit is separately encoded in four bits

An ADC converts an analog signal to a digital signal and a DAC converts digital signals to analog

  • In binary the quantity two is written 0010 - place values from the right are 1, 2, 4, 8
  • Last updated: August 2026

11.8 Counters, Prescalers, BCD & Data Converters

Quick Answer: A prescaler divides an HF signal so a low-frequency counter can display the operating frequency . A decade counter gives one output pulse per ten input pulses . BCD = binary coded decimal . ADC = analog to digital; DAC = digital to analog. Binary two = 0010 .

Sub-topic 3-E-040 (Counters, Dividers, Converters) is the bridge between the digital chapter and the test-equipment chapter, because the prescaler question is really a frequency-counter question.

The prescaler

What is the purpose of a prescaler circuit? It divides an HF signal so that a low-frequency counter can display the operating frequency.

The problem it solves is concrete. A frequency counter's internal logic has a maximum toggle rate — an older TTL counter might top out around 50 MHz. Measure a 450 MHz transmitter with it directly and you get nonsense. Put a divide-by-10 or divide-by-100 prescaler in front, built from a fast logic family, and 450 MHz becomes 45 MHz or 4.5 MHz, comfortably inside the counter's range.

Two practical consequences a technician must remember:

Multiply the reading back. A ÷100 prescaler showing 4.500000 MHz means 450.0000 MHz . Some counters do this automatically when a prescaler is selected; a standalone prescaler does not.

Resolution is divided too. Dividing by 100 costs you two digits of resolution for the same gate time. To recover them you must extend the gate time proportionally.

This links directly to section 7.5: the prescaler extends range , while the time base sets accuracy . A prescaler does not make a ±10 ppm counter any more accurate.

The decade counter

What is the function of a decade counter digital IC? Produce one output pulse for every ten input pulses.

"Decade" means ten. A decade counter counts 0 through 9 and rolls over, emitting one carry pulse per cycle — so it is a ÷10 stage. Cascade them and each stage divides by another ten, which is exactly how a frequency counter's display chain is built: units, tens, hundreds, thousands.

  • Divider Division ratio Typical use
  • Decade counter ÷10 Frequency counter display stages, decimal timing
  • Binary counter (4-bit) ÷16 Address generation, binary timing
  • Prescaler ÷10, ÷64, ÷100, ÷1000 Extending counter range at UHF
  • Flip-flop (single) ÷2 The basic building block (section 11.2)

Note the contrast in the table: a plain 4-bit binary counter divides by 16 , not 10. A decade counter is a binary counter with feedback that forces it to reset after nine, which is what makes decimal displays possible.

BCD

What does the term "BCD" mean? Binary coded decimal.

In BCD each decimal digit is encoded separately in four bits :

  • Decimal BCD Pure binary
  • 7 0111 0111
  • 9 1001 1001
  • 25 0010 0101 11001
  • 156 0001 0101 0110 10011100

The difference matters. 25 in BCD is 0010 0101 — the digit 2 then the digit 5 — whereas 25 in pure binary is 11001. BCD wastes code space, since the four-bit combinations 1010 through 1111 are never used, but it converts to a decimal display with no arithmetic at all. That is why frequency counters, digital multimeters and channel displays use it: each BCD nibble drives one seven-segment digit directly through a decoder.

ADC and DAC

What integrated circuit device converts an analog signal to a digital signal? ADC. What integrated circuit device converts digital signals to analog signals? DAC.

Read the acronym left to right and the direction is unambiguous:

  • Device Full name Direction Radio example
  • ADC Analog-to-Digital Converter Analog → digital Digitising received audio or IF for DSP

DAC Digital-to-Analog Converter Digital → analog Reconstructing audio; generating the waveform in a direct digital synthesiser

The DAC appears again in section 10.2 as part of the direct digital synthesiser signal chain — phase accumulator, look-up table , DAC , then a low-pass anti-alias filter to remove the sampling images. That anti-alias filter is the specific block the pool names, so do not stop the chain at the DAC.

Binary notation

In binary numbers, how would you note the quantity TWO? 0010.

Place values run right to left as powers of two:

  • Bit position 8 4 2 1
  • Decimal 1 0 0 0 1
  • Decimal 2 0 0 1 0
  • Decimal 3 0 0 1 1
  • Decimal 4 0 1 0 0
  • Decimal 8 1 0 0 0

Two sets the 2s column and nothing else: 0010 . The distractors are 0001 (that is one), 0100 (four), and 1000 (eight) — all off by a power of two, so count the columns from the right rather than trusting the shape of the pattern.