Study guide

11.2 Flip-Flops & Sequential Elements

FCC General Radiotelephone Operator License GROL

Track your progress as you read

Finished sections get a check mark.

1 Introduction & GROL Exam Overview

1.1 About the General Radiotelephone Operator License 1.2 Exam Format, COLEMs, FRN & Application Process

2 Element 1: Rules & Regulations

2.1 Equipment Requirements (Part 80) 2.2 License Requirements & Operator Authority 2.3 Watchkeeping & Logkeeping Duties 2.4 Log Entries & Required Records 2.5 Ship Station Control, Inspections & International Rules

3 Element 1: Communications Procedures

3.1 Bridge-to-Bridge Operations & VTS 3.2 Distress Communications & Alerting 3.3 Operating Procedures, Calling & Testing 3.4 Urgency (PAN PAN) & Safety (SECURITE) Traffic 3.5 The GMDSS Concept & Ship Responsibilities

4 Element 1: Equipment Operations

4.1 VHF Equipment Controls 4.2 MF/HF SSB Equipment Controls 4.3 DSC Operations & Equipment Faults 4.4 VHF Channel Selection & Channel Assignments 4.5 MF/HF Frequency & Emission Selection 4.6 Required Equipment Tests & On-Air Test Procedure

5 Element 1: Other Equipment & Antennas

5.1 Marine Antennas & Polarization 5.2 EPIRBs & Emergency Beacons 5.3 Power Sources, Reserve Power & Required Tests 5.4 Search and Rescue Transponders (SARTs) 5.5 Survival Craft Portable VHF (SCT) Requirements 5.6 NAVTEX & Maritime Safety Information

6 Element 3: Electrical Principles

6.1 Electrical Elements, Units & Power Types 6.2 Magnetism & Magnetic Circuits 6.3 Resistance, Capacitance & Inductance 6.4 Waveforms & Semiconductor Introduction 6.5 Materials, Corrosion & Skin Effect 6.6 AC Measurement & Conversion Factors 6.7 Conduction, Reactive Power & Maximum Power Transfer

7 Element 3: Electrical Math

7.1 Ohm's Law — Series & Parallel Circuits 7.2 Frequency, Period, Wavelength & Waveform Math 7.3 Power Relationships & Decibels 7.4 RC/RL Time Constants 7.5 Frequency Counter Accuracy, PPM & Harmonics 7.6 Impedance in Rectangular & Polar Coordinates 7.7 Regulation, Turns Ratio, Zener Bias & Conductance

8 Element 3: Circuit Components — Passives & Power Devices

8.1 Capacitors & Photoconductive Devices 8.2 Transformers, Voltage Regulators & Zener Diodes 8.3 Diodes, SCRs & Triacs

9 Element 3: Active Components — Transistors & Devices

9.1 Bipolar Junction Transistors 9.2 FETs, LEDs & Specialty Devices 9.3 Device Selection, Ratings & Thermal Design

10 Element 3: Practical Circuits — RLC, Op Amps & Schematics

10.1 R-L-C Resonant Circuits 10.2 Op Amps, PLLs, VCOs & Mixers 10.3 Reading Schematics & Signal Flow

11 Element 3: Digital Logic

11.1 Logic Gates & Boolean Functions 11.2 Flip-Flops & Sequential Elements 11.3 Multivibrators & Timing Circuits 11.4 Microprocessors & Bus Architecture 11.5 TTL Logic Families & Input Voltage Levels 11.6 Positive & Negative Logic and Truth Tables 11.7 Memory Types & Microprocessor Concepts 11.8 Counters, Prescalers, BCD & Data Converters

12 Element 3: Receivers

12.1 Receiver Theory & Superheterodyne Architecture 12.2 RF Amplifiers & Front-End Design 12.3 Filters & Detectors 12.4 Audio, Squelch & Receiver Performance Specs 12.5 Receiver Oscillators: Colpitts, Hartley & Pierce 12.6 Mixing, Image Frequencies & Spurious Products 12.7 IF Selectivity & Filter Bandwidth

13 Element 3: Transmitters

13.1 RF Amplifier Classes & Efficiency 13.2 Oscillators, Modulators & Tuning Networks 13.3 SSB Transmitters & Modern Transmitter Technology

14 Element 3: Signals, Emissions & Modulation

14.1 Amplitude & Frequency Modulation 14.2 Single-Sideband Modulation 14.3 Pulse Modulation & Emission Types

15 Element 3: Power Sources

15.1 Batteries & Energy Storage 15.2 Motors, Generators & Power Supplies

16 Element 3: Antennas & Feed Lines

16.1 Antenna Theory, Types & Patterns 16.2 Voltage, Current & Impedance on Antennas 16.3 Transmission Lines, Velocity Factor & SWR 16.4 Effective Radiated Power & Antenna Bandwidth

17 Element 3 Background: Propagation & Radio Practice

17.1 Radio Wave Propagation Modes 17.2 Multipath, Fading & Doppler Effects 17.3 Radio Practice, Interference & Good Engineering

18 Element 3: Aircraft Radio Navigation Systems

18.1 DME & VOR 18.2 ILS, ADF & ATC Transponders 18.3 Aircraft Antennas, Frequencies & Equipment Functions

19 Element 3: Installation, Maintenance & Repair

19.1 Indicating Meters & Meter Movements 19.2 Oscilloscopes & Waveform Measurement 19.3 Measurement Procedures 19.4 Installation Codes & Bonding Procedures 19.5 Frequency Standards, SINAD Meters & EMI Hunting 19.6 Spectrum Analyzers, TDRs & Service Monitors 19.7 Bench Repair Practices, ESD & Rework Tools 19.8 Systematic Troubleshooting & Field Fault Diagnosis

20 Element 3: Communications Technology & Marine Systems

20.1 Transmission Types, Coding & Multiplexing 20.2 Signal Processing, Software & Codes 20.3 Marine VHF, MF/HF & SSB-SITOR 20.4 Survival Craft Electronics, FAX & NAVTEX 20.5 NMEA 0183 & NMEA 2000 Data Networks

21 Element 3: RADAR & Satellite Systems

21.1 RADAR Theory & Pulse Fundamentals 21.2 Range, Pulse Width & PRF 21.3 Radar Antennas & Waveguides 21.4 INMARSAT Satellite Communications 21.5 RADAR Components: Magnetron, Duplexer, ATR & Synchro 21.6 RADAR Equipment, ARPA & Radiation Safety 21.7 Low Earth Orbit Systems: Iridium & COSPAS-SARSAT 21.8 GPS Satellite Navigation & DGPS

22 Element 3: RF & Electrical Safety

22.1 RF Radiation Exposure Limits 22.2 Electrical Safety Practices for Radio Technicians

23 Study Strategy & Exam Day

23.1 Study Strategy, Practice Plan & Exam Day

11.2 Flip-Flops & Sequential Elements

Key Takeaways Explain This Topic AI

TTL stands for transistor-transistor logic; the common TTL power-supply voltage is 5 V, with valid inputs roughly 0–0.8 V low and 2.0–5.5 V high on a 5 V rail

TTL inputs left open tend to float to a high-logic state; a logic probe is the preferred instrument for checking TTL logic levels on a live board

A flip-flop is a binary sequential logic element with two stable states; one flip-flop stores one bit of information

Two flip-flops divide a signal frequency by 4; an 8-bit storage register needs eight R-S flip-flops (one bit per flip-flop)

R-S flip-flops do not operate in toggle mode with R-S held constant while the clock runs—that toggle behavior belongs to T or JK configurations, not basic R-S

Last updated: August 2026

11.2 Logic Levels & Flip-Flops

Quick Answer: TTL = transistor-transistor logic , usually on 5 V . Valid TTL input low ≈ 0–0.8 V ; valid high ≈ 2.0–5.5 V . Open TTL inputs float high . Best checker: logic probe . A flip-flop has 2 stable states and stores 1 bit . 2 flip-flops divide frequency by 4 ; 8 R-S flip-flops make an 8-bit register. R-S does not toggle with R-S held constant under clock.

Gates alone are combinational—outputs follow inputs immediately. Real radios need memory and predictable voltage bands . Key topic 033 locks in TTL numbers; key topic 036 introduces the flip-flop as the one-bit memory cell.

TTL — transistor-transistor logic

What do the initials TTL stand for? Transistor-transistor logic.

TTL is the classic bipolar digital family (7400-series and descendants). Internally, multi-emitter bipolar transistors form the input structure—hence the name, not “resistor-transistor,” “diode-transistor,” or “emitter-coupled” logic (those are other historical families: RTL, DTL, ECL).

Power supply

Common power supply voltage for TTL series integrated circuits: 5 volts.

Ship and aircraft 12/24/28 V buses always step down (regulators, DC-DC converters) before feeding TTL. Never assume a bare chassis voltage is safe for a TTL package—look for the +5 V logic rail and its ground return.

Valid logic levels (5 V TTL)

  • Parameter (5 V TTL, pool) Voltage range
  • Valid logic low input Zero to 0.8 volts
  • Valid logic high input 2.0 to 5.5 volts
  • Typical VCC 5 V

Valid logic low input in a TTL device operating at 5 volts: zero to 0.8 volts.

Valid logic high input in a TTL device operating at 5.0 volts: 2.0 to 5.5 volts.

The gap between 0.8 V and 2.0 V is the undefined / transition region. A noisy signal stuck at 1.4 V is not a legal 0 or 1—expect flaky gates, oscillation, or excess supply current. That gap is also where noise margin lives: the difference between a guaranteed output high/low and the worst-case input threshold that still reads correctly.

Noise margin (technician view)

Noise margin is how much interference a logic input can tolerate before a legal 0 looks like a 1 (or vice versa).

  • Direction Idea
  • Low-level noise margin How far a valid “0” output can rise and still look like a “0” to the next input
  • High-level noise margin How far a valid “1” output can sag and still look like a “1”

TTL’s wide gap (0.8 V low max vs 2.0 V high min) gives solid margins for short board runs. Long cable runs, shared grounds with RF decks, and weak pull-ups erode that margin—exactly when radios get “ghost” key-ups and intermittent synthesizer unlocks.

Open TTL inputs

TTL inputs left open develop what logic state? A high-logic state.

Floating TTL inputs are not “ignored” and are not random by design—they tend to rise toward a high because of internal structure. That high can make an unused AND input look permanently true, or turn a NOR into a stuck-low output. Good practice: tie unused inputs to a defined level (often high via resistor for TTL, or per datasheet for CMOS).

Best instrument for TTL checks

Which instrument is best for checking a TTL logic circuit? A logic probe.

A logic probe is designed for digital high/low/pulse indication at TTL (and often CMOS) thresholds. A general VOM/DMM can measure voltage but is slow for pulsing nets and does not give an instant “high / low / pulse” indication. Continuity testers are for wiring, not live logic states.

  • Tool Digital troubleshooting role
  • Logic probe Fast high/low/pulse on TTL nodes
  • Oscilloscope Timing, glitches, rise time, multi-channel
  • DMM/VOM Static rail checks, not best for pulsing logic
  • Continuity tester Wiring / shorts only
  • CMOS levels (comparison for modern radios)

Element 3’s numbered pool emphasizes TTL thresholds, but modern marine/aviation radios are full of CMOS (complementary metal-oxide semiconductor) microcontrollers and synthesizer logic. CMOS often runs at 5 V, 3.3 V, or lower, and its valid high/low fractions track a larger portion of VCC than classic TTL.

  • Family trait TTL (pool focus) CMOS (field reality)
  • Supply Typically 5 V 1.8–5 V class common
  • Static power Higher Very low when idle
  • Input impedance Moderate Extremely high (static sensitive)
  • Open inputs Tend high Undefined—must not float
  • Interface risk Mixing 5 V TTL into 3.3 V CMOS can over-volt inputs

When you interface a legacy TTL board to a CMOS MCU on a retrofit, use level translators or series resistors per the datasheet—do not assume 5 V high is safe on a 3.3 V pin.

Flip-flops — two stable states, one bit

A flip-flop circuit is a binary logic element with how many stable states? 2.

What is a flip-flop circuit? A binary sequential logic element with 2 stable states.

Those two states are logic 0 and logic 1 at the Q output (with Q ‾ \overline{Q} Q ​ complementary on many packages). Unlike an AND gate that forgets inputs the instant they change, a flip-flop remembers until something commands a change—set, reset, clocked data, or toggle.

How many bits of information can be stored in a single flip-flop circuit? 1.

Registers, shift registers, and counters are just arrays of flip-flops sharing clocks and control lines.

Latches vs flip-flops (field distinction)

  • Device Timing idea Typical use
  • Latch Level-sensitive: transparent while enable is active Temporary hold, bus interface
  • Flip-flop Edge-triggered: samples on rising or falling clock edge Synchronous registers, counters

Element 3 wording centers on “flip-flop” and R-S behavior; in the shop, treat edge-triggered parts as the reliable choice for clocked radio logic so data is not still changing while the enable is open.

R-S (SR) flip-flop

R = Reset, S = Set (sometimes labeled R / S or R ‾ \overline{R} R / S ‾ \overline{S} S for active-low).

  • S R Action (active-high SR idea)
  • 0 0 Hold (memory)
  • 1 0 Set Q = 1
  • 0 1 Reset Q = 0
  • 1 1 Forbidden / race (avoid)

Many packages add asynchronous PRE (preset) and CLR (clear) that force Q without waiting for the clock, and synchronous R-S (or D) inputs sampled when CLK is initiated.

How many R-S flip-flops are required to construct an 8-bit storage register? 8 — one flip-flop per bit.

An R-S flip-flop is capable of doing all of the following except: operate in toggle mode with R-S inputs held constant and CLK initiated.

That “except” is a classic pool trap. R-S can:

Accept data into R-S with CLK initiated (synchronous path).

Accept PRE/CLR without CLK (asynchronous path).

Refuse synchronous data when asynchronous inputs are asserting (async wins).

It does not free-run as a toggle just because the clock keeps ticking while R and S sit fixed. Toggle mode is the T flip-flop (or a JK wired for toggle).

D, JK, and T (technician map)

  • Type Rule of thumb
  • D (data) Q follows D on the clock edge—workhorse register bit
  • JK More general; can set, reset, hold, or toggle depending on J/K
  • T (toggle) Flips Q each clock when T = 1—natural ÷2 stage
  • R-S Set/reset memory; not a free toggler with fixed R-S
  • Frequency division with flip-flops

Each toggle stage halves frequency: f o u t = f i n / 2 f_{out} = f_{in}/2 f o u t ​ = f in ​ /2 .

How many flip-flops are required to divide a signal frequency by 4? 2. f 2 → 1st FF f 4 → 2nd FF \frac{f}{2} \xrightarrow{\text{1st FF}} \frac{f}{4} \xrightarrow{\text{2nd FF}} 2 f ​ 1st FF ​ 4 f ​ 2nd FF ​

Chain more stages for ÷8, ÷16, and so on—exactly how binary counters and many PLL reference dividers are built (expanded in §11.4).

Worked example — 8-bit channel latch

A legacy marine VHF control board latches an 8-bit channel code from a rotary encoder:

Eight D or R-S flip-flops share one clock derived from the encoder “enter” pulse.

Each flip-flop stores one bit of the channel number ( 8 bits → 8 flip-flops ).

Q outputs feed the synthesizer programming lines until the next enter pulse.

If one flip-flop fails stuck, one bit of the channel is frozen—symptoms look like “wrong frequency but panel display correct” when the display is driven from a different path.

TTL probing checklist on a live radio

Confirm +5 V rail and clean ground at the IC before blaming logic.

Use a logic probe for high/low/pulse on TTL pins.

Treat 0–0.8 V as low, 2.0–5.5 V as high; distrust mid-band voltages.

Do not leave unused TTL inputs floating—they read high .

Remember flip-flops hold state after power glitches if the supply stayed up—cycle power when stuck bits make no sense.

Exam-day checklist for 033 & 036

TTL = transistor-transistor logic ; supply 5 V .

Low input 0–0.8 V ; high input 2.0–5.5 V .

Open TTL input → high ; best tool → logic probe .

Flip-flop → 2 stable states; stores 1 bit.

÷4 needs 2 flip-flops; 8-bit register needs 8 R-S flip-flops.

R-S does not toggle with R-S constant under clock.

Next section folds flip-flops into the multivibrator family and compares RAM/ROM memory types that hold programs and channel data in radio gear.