Study guide
11.3 Multivibrators & Timing Circuits
FCC General Radiotelephone Operator License GROL
Track your progress as you read
Finished sections get a check mark.
1 Introduction & GROL Exam Overview
1.1 About the General Radiotelephone Operator License 1.2 Exam Format, COLEMs, FRN & Application Process
2 Element 1: Rules & Regulations
2.1 Equipment Requirements (Part 80) 2.2 License Requirements & Operator Authority 2.3 Watchkeeping & Logkeeping Duties 2.4 Log Entries & Required Records 2.5 Ship Station Control, Inspections & International Rules
3 Element 1: Communications Procedures
3.1 Bridge-to-Bridge Operations & VTS 3.2 Distress Communications & Alerting 3.3 Operating Procedures, Calling & Testing 3.4 Urgency (PAN PAN) & Safety (SECURITE) Traffic 3.5 The GMDSS Concept & Ship Responsibilities
4 Element 1: Equipment Operations
4.1 VHF Equipment Controls 4.2 MF/HF SSB Equipment Controls 4.3 DSC Operations & Equipment Faults 4.4 VHF Channel Selection & Channel Assignments 4.5 MF/HF Frequency & Emission Selection 4.6 Required Equipment Tests & On-Air Test Procedure
5 Element 1: Other Equipment & Antennas
5.1 Marine Antennas & Polarization 5.2 EPIRBs & Emergency Beacons 5.3 Power Sources, Reserve Power & Required Tests 5.4 Search and Rescue Transponders (SARTs) 5.5 Survival Craft Portable VHF (SCT) Requirements 5.6 NAVTEX & Maritime Safety Information
6 Element 3: Electrical Principles
6.1 Electrical Elements, Units & Power Types 6.2 Magnetism & Magnetic Circuits 6.3 Resistance, Capacitance & Inductance 6.4 Waveforms & Semiconductor Introduction 6.5 Materials, Corrosion & Skin Effect 6.6 AC Measurement & Conversion Factors 6.7 Conduction, Reactive Power & Maximum Power Transfer
7 Element 3: Electrical Math
7.1 Ohm's Law — Series & Parallel Circuits 7.2 Frequency, Period, Wavelength & Waveform Math 7.3 Power Relationships & Decibels 7.4 RC/RL Time Constants 7.5 Frequency Counter Accuracy, PPM & Harmonics 7.6 Impedance in Rectangular & Polar Coordinates 7.7 Regulation, Turns Ratio, Zener Bias & Conductance
8 Element 3: Circuit Components — Passives & Power Devices
8.1 Capacitors & Photoconductive Devices 8.2 Transformers, Voltage Regulators & Zener Diodes 8.3 Diodes, SCRs & Triacs
9 Element 3: Active Components — Transistors & Devices
9.1 Bipolar Junction Transistors 9.2 FETs, LEDs & Specialty Devices 9.3 Device Selection, Ratings & Thermal Design
10 Element 3: Practical Circuits — RLC, Op Amps & Schematics
10.1 R-L-C Resonant Circuits 10.2 Op Amps, PLLs, VCOs & Mixers 10.3 Reading Schematics & Signal Flow
11 Element 3: Digital Logic
11.1 Logic Gates & Boolean Functions 11.2 Flip-Flops & Sequential Elements 11.3 Multivibrators & Timing Circuits 11.4 Microprocessors & Bus Architecture 11.5 TTL Logic Families & Input Voltage Levels 11.6 Positive & Negative Logic and Truth Tables 11.7 Memory Types & Microprocessor Concepts 11.8 Counters, Prescalers, BCD & Data Converters
12 Element 3: Receivers
12.1 Receiver Theory & Superheterodyne Architecture 12.2 RF Amplifiers & Front-End Design 12.3 Filters & Detectors 12.4 Audio, Squelch & Receiver Performance Specs 12.5 Receiver Oscillators: Colpitts, Hartley & Pierce 12.6 Mixing, Image Frequencies & Spurious Products 12.7 IF Selectivity & Filter Bandwidth
13 Element 3: Transmitters
13.1 RF Amplifier Classes & Efficiency 13.2 Oscillators, Modulators & Tuning Networks 13.3 SSB Transmitters & Modern Transmitter Technology
14 Element 3: Signals, Emissions & Modulation
14.1 Amplitude & Frequency Modulation 14.2 Single-Sideband Modulation 14.3 Pulse Modulation & Emission Types
15 Element 3: Power Sources
15.1 Batteries & Energy Storage 15.2 Motors, Generators & Power Supplies
16 Element 3: Antennas & Feed Lines
16.1 Antenna Theory, Types & Patterns 16.2 Voltage, Current & Impedance on Antennas 16.3 Transmission Lines, Velocity Factor & SWR 16.4 Effective Radiated Power & Antenna Bandwidth
17 Element 3 Background: Propagation & Radio Practice
17.1 Radio Wave Propagation Modes 17.2 Multipath, Fading & Doppler Effects 17.3 Radio Practice, Interference & Good Engineering
18 Element 3: Aircraft Radio Navigation Systems
18.1 DME & VOR 18.2 ILS, ADF & ATC Transponders 18.3 Aircraft Antennas, Frequencies & Equipment Functions
19 Element 3: Installation, Maintenance & Repair
19.1 Indicating Meters & Meter Movements 19.2 Oscilloscopes & Waveform Measurement 19.3 Measurement Procedures 19.4 Installation Codes & Bonding Procedures 19.5 Frequency Standards, SINAD Meters & EMI Hunting 19.6 Spectrum Analyzers, TDRs & Service Monitors 19.7 Bench Repair Practices, ESD & Rework Tools 19.8 Systematic Troubleshooting & Field Fault Diagnosis
20 Element 3: Communications Technology & Marine Systems
20.1 Transmission Types, Coding & Multiplexing 20.2 Signal Processing, Software & Codes 20.3 Marine VHF, MF/HF & SSB-SITOR 20.4 Survival Craft Electronics, FAX & NAVTEX 20.5 NMEA 0183 & NMEA 2000 Data Networks
21 Element 3: RADAR & Satellite Systems
21.1 RADAR Theory & Pulse Fundamentals 21.2 Range, Pulse Width & PRF 21.3 Radar Antennas & Waveguides 21.4 INMARSAT Satellite Communications 21.5 RADAR Components: Magnetron, Duplexer, ATR & Synchro 21.6 RADAR Equipment, ARPA & Radiation Safety 21.7 Low Earth Orbit Systems: Iridium & COSPAS-SARSAT 21.8 GPS Satellite Navigation & DGPS
22 Element 3: RF & Electrical Safety
22.1 RF Radiation Exposure Limits 22.2 Electrical Safety Practices for Radio Technicians
23 Study Strategy & Exam Day
23.1 Study Strategy, Practice Plan & Exam Day
11.3 Multivibrators & Timing Circuits
Key Takeaways Explain This Topic AI
Astable multivibrators alternate between two unstable states and free-run as square-wave clocks; monostable (one-shot) circuits switch briefly then return to a single stable state after a set time
A bistable multivibrator is commonly named a flip-flop and is the circuit type used to divide an AC signal frequency electronically
Collector outputs of an astable multivibrator common-emitter stage produce square waves, not sine or sawtooth
RAM is read/write random-access memory; ROM holds a fixed pattern; DRAM must be refreshed periodically to keep data
Nonvolatile types (ROM, EPROM, EEPROM, flash) retain data without power; volatile RAM/DRAM lose data when power is removed—critical for radio firmware vs working channel memory
Last updated: August 2026
11.3 Multivibrators & Memory
Quick Answer: Astable = two unstable states (free-running square-wave clock). Monostable = one-shot: flips briefly, returns after a set time. Bistable = flip-flop (two stable states); used to divide frequency . Astable CE collectors → square wave . RAM = read/write random access; ROM = fixed pattern; DRAM needs refresh . Volatile loses data without power; nonvolatile keeps it.
Key topic 037 classifies multivibrators by how many stable states they have. Key topic 038 names the memory chips that store the bits those circuits create. Together they explain both the free-running clock crystal’s digital sidekick and the firmware that boots a modern transceiver.
Multivibrators — three families
A multivibrator is a regenerative two-state switching circuit. The “multi” is historical; what matters on Element 3 is astable / monostable / bistable .
- Type Stable states Behavior Common name / use
- Astable 0 (none) Alternates between two unstable states forever Free-running clock, square-wave generator
- Monostable 1 Trigger flips it; returns after timed delay One-shot, pulse stretcher, debouncer
- Bistable 2 Stays in either state until commanded Flip-flop , memory bit, frequency divider
- Astable multivibrator
What is an astable multivibrator? A circuit that alternates between two unstable states.
No external clock is required—the circuit is its own oscillator. Two amplifier stages with RC cross-coupling (classic transistor pair or a 555-style topology) never rest; each state times out and flips the other.
What waveform appears on the voltage outputs at the collectors of an astable multivibrator common-emitter stage? A square wave.
Collectors slam between near-cutoff and near-saturation, so the waveform is rectangular/square, not sine, sawtooth, or half-wave pulses. That square wave is a natural logic clock or a tone for testing digital stages.
- Astable fact Element 3 hook
- States Two unstable
- Free-running? Yes
- Collector waveform (CE) Square wave
- Also called Free-running multivibrator
- Monostable multivibrator (one-shot)
What is a monostable multivibrator? A circuit that can be switched momentarily to the opposite binary state and then returns after a set time to its original state.
One state is stable; the other is temporary. A trigger pulse starts the timing interval (RC network or digital timer); when the interval ends, the circuit snaps back. Uses on radio gear:
Stretch a short PTT contact bounce into a clean keying pulse.
Generate a fixed-width mute blanking interval after channel change.
Produce a single enable pulse for a DAC update or synthesizer load strobe.
Do not confuse monostable with a free-running clock (that is astable) or with a permanent bit store (that is bistable).
Bistable multivibrator = flip-flop
What is a bistable multivibrator circuit commonly named? A flip-flop.
What is a bistable multivibrator circuit? A flip-flop.
Two stable states → holds 0 or 1 until set, reset, or clocked. This is the same device family as §11.2, now named from the multivibrator taxonomy.
The frequency of an AC signal can be divided electronically by what type of digital circuit? A bistable multivibrator.
Each toggle stage halves frequency. Free-running (astable) multivibrators generate a frequency; they do not systematically divide an external AC signal the way cascaded flip-flops do. OR gates are combinational and do not count. That is why the pool answer is bistable , not astable or free-running.
Multivibrator decision tree for the exam
- Clue in the question Pick
- Continuous square-wave clock, no external trigger required Astable
- Single pulse of fixed width after a trigger Monostable
- Stores a bit / named flip-flop / divides frequency Bistable
- Collector outputs look square Astable CE stage
- Semiconductor memory — RAM, ROM, DRAM
- RAM — random-access memory
Name of the semiconductor memory IC whose digital data can be written or read, and whose memory word address can be accessed randomly: RAM – Random-Access Memory.
“Random access” means any address is available in roughly the same time—unlike sequential tape. Working variables, channel scratchpads, and packet buffers live in RAM while power is on.
ROM — read-only memory
Name of the semiconductor IC that has a fixed pattern of digital data stored in its memory matrix: ROM – Read-Only Memory.
Factory-masked or permanently programmed content: boot code, fixed lookup tables, character generators. You read it; you do not casually rewrite it in the field (contrast EEPROM/flash below).
DRAM — dynamic RAM needs refresh
Name of the random-accessed semiconductor memory IC that must be refreshed periodically to maintain reliable data storage: DRAM – Dynamic Random-Access Memory.
DRAM stores bits as charge on tiny capacitors. Charge leaks; a refresh controller rewrites cells before data vanishes. SRAM (static RAM) uses flip-flop cells and does not need refresh, but costs more silicon per bit—Element 3 explicitly tests the DRAM + refresh pair.
Type Read/write? Power-off retention Refresh?
- RAM (general) Yes No (volatile) Depends on subtype
- SRAM Yes No No
- DRAM Yes No Yes
- ROM Read (fixed) Yes (nonvolatile) No
- Memory cell count (address × data width)
How many individual memory cells in a memory IC with 4 data bus I/O pins and 4 address pins? 64.
Reasoning:
4 address pins select 2 4 = 16 2^4 = 16 2 4 = 16 addresses.
4 data pins mean 4 bits per address.
Total cells = 16 × 4 = 64 16 \times 4 = 64 16 × 4 = 64 .
General rule: cells ≈ (2^{address pins}) × (data width in bits) for a simple parallel memory organization.
IO and program (system vocabulary from the pool)
What does “IO” mean within a microprocessor system? Input-output.
What is the name for a microprocessor’s sequence of commands and instructions? A program.
IO is how the CPU talks to keypads, displays, synthesizer chips, and AF stages. The program is the ordered instruction stream—usually fetched from ROM/flash into the execution path, with RAM holding temporary data.
EPROM, EEPROM, and flash (nonvolatile context)
The numbered pool names EPROM mainly as a distractor in RAM questions, but GROL fieldwork requires the family distinctions:
- Memory How you erase / rewrite Volatility
- ROM (mask) Not field-rewritable Nonvolatile
- PROM One-time programmable (fuses) Nonvolatile
- EPROM UV erase window, then reprogram Nonvolatile
- EEPROM Electrically erasable, often byte-wise Nonvolatile
- Flash Electrically erasable in blocks/sectors Nonvolatile
- RAM/DRAM Read/write anytime Volatile
Volatile vs nonvolatile:
Volatile (RAM/DRAM): data vanishes when power is removed—working memory, volatile channel scratchpads without battery backup.
Nonvolatile (ROM/EPROM/EEPROM/flash): firmware, calibration constants, and saved channel banks survive power-off.
Modern radios store firmware in flash , user preferences in EEPROM or flash file systems, and live DSP buffers in RAM/DRAM . Battery-backed SRAM still appears in older avionics for configuration.
- Shop story — dead after power cycle
- Symptoms: radio works until battery disconnect, then boots to defaults or “no program.”
Check whether configuration was only in volatile RAM without backup.
Verify flash/EEPROM still has firmware (nonvolatile failure is rarer but catastrophic).
Distinguish “lost user channels” (EEPROM/config) from “won’t boot” (ROM/flash corruption).
Exam-day checklist for 037–038
Astable → two unstable states; collectors → square wave .
Monostable → momentary flip, returns after set time .
Bistable → flip-flop ; divides frequency.
RAM → read/write random access; ROM → fixed pattern.
DRAM → must be refreshed .
4 address + 4 data pins → 64 cells.
IO = input-output ; instruction sequence = program .
Volatile loses data without power; ROM/EPROM/EEPROM/flash keep it.
Next section puts memory and clocks inside microprocessors , then covers counters, prescalers, BCD, ADC, and DAC —the digital heart of frequency synthesis and modern radio signal chains.