Study guide

11.6 Positive & Negative Logic and Truth Tables

FCC General Radiotelephone Operator License GROL

Track your progress as you read

Finished sections get a check mark.

1 Introduction & GROL Exam Overview

1.1 About the General Radiotelephone Operator License 1.2 Exam Format, COLEMs, FRN & Application Process

2 Element 1: Rules & Regulations

2.1 Equipment Requirements (Part 80) 2.2 License Requirements & Operator Authority 2.3 Watchkeeping & Logkeeping Duties 2.4 Log Entries & Required Records 2.5 Ship Station Control, Inspections & International Rules

3 Element 1: Communications Procedures

3.1 Bridge-to-Bridge Operations & VTS 3.2 Distress Communications & Alerting 3.3 Operating Procedures, Calling & Testing 3.4 Urgency (PAN PAN) & Safety (SECURITE) Traffic 3.5 The GMDSS Concept & Ship Responsibilities

4 Element 1: Equipment Operations

4.1 VHF Equipment Controls 4.2 MF/HF SSB Equipment Controls 4.3 DSC Operations & Equipment Faults 4.4 VHF Channel Selection & Channel Assignments 4.5 MF/HF Frequency & Emission Selection 4.6 Required Equipment Tests & On-Air Test Procedure

5 Element 1: Other Equipment & Antennas

5.1 Marine Antennas & Polarization 5.2 EPIRBs & Emergency Beacons 5.3 Power Sources, Reserve Power & Required Tests 5.4 Search and Rescue Transponders (SARTs) 5.5 Survival Craft Portable VHF (SCT) Requirements 5.6 NAVTEX & Maritime Safety Information

6 Element 3: Electrical Principles

6.1 Electrical Elements, Units & Power Types 6.2 Magnetism & Magnetic Circuits 6.3 Resistance, Capacitance & Inductance 6.4 Waveforms & Semiconductor Introduction 6.5 Materials, Corrosion & Skin Effect 6.6 AC Measurement & Conversion Factors 6.7 Conduction, Reactive Power & Maximum Power Transfer

7 Element 3: Electrical Math

7.1 Ohm's Law — Series & Parallel Circuits 7.2 Frequency, Period, Wavelength & Waveform Math 7.3 Power Relationships & Decibels 7.4 RC/RL Time Constants 7.5 Frequency Counter Accuracy, PPM & Harmonics 7.6 Impedance in Rectangular & Polar Coordinates 7.7 Regulation, Turns Ratio, Zener Bias & Conductance

8 Element 3: Circuit Components — Passives & Power Devices

8.1 Capacitors & Photoconductive Devices 8.2 Transformers, Voltage Regulators & Zener Diodes 8.3 Diodes, SCRs & Triacs

9 Element 3: Active Components — Transistors & Devices

9.1 Bipolar Junction Transistors 9.2 FETs, LEDs & Specialty Devices 9.3 Device Selection, Ratings & Thermal Design

10 Element 3: Practical Circuits — RLC, Op Amps & Schematics

10.1 R-L-C Resonant Circuits 10.2 Op Amps, PLLs, VCOs & Mixers 10.3 Reading Schematics & Signal Flow

11 Element 3: Digital Logic

11.1 Logic Gates & Boolean Functions 11.2 Flip-Flops & Sequential Elements 11.3 Multivibrators & Timing Circuits 11.4 Microprocessors & Bus Architecture 11.5 TTL Logic Families & Input Voltage Levels 11.6 Positive & Negative Logic and Truth Tables 11.7 Memory Types & Microprocessor Concepts 11.8 Counters, Prescalers, BCD & Data Converters

12 Element 3: Receivers

12.1 Receiver Theory & Superheterodyne Architecture 12.2 RF Amplifiers & Front-End Design 12.3 Filters & Detectors 12.4 Audio, Squelch & Receiver Performance Specs 12.5 Receiver Oscillators: Colpitts, Hartley & Pierce 12.6 Mixing, Image Frequencies & Spurious Products 12.7 IF Selectivity & Filter Bandwidth

13 Element 3: Transmitters

13.1 RF Amplifier Classes & Efficiency 13.2 Oscillators, Modulators & Tuning Networks 13.3 SSB Transmitters & Modern Transmitter Technology

14 Element 3: Signals, Emissions & Modulation

14.1 Amplitude & Frequency Modulation 14.2 Single-Sideband Modulation 14.3 Pulse Modulation & Emission Types

15 Element 3: Power Sources

15.1 Batteries & Energy Storage 15.2 Motors, Generators & Power Supplies

16 Element 3: Antennas & Feed Lines

16.1 Antenna Theory, Types & Patterns 16.2 Voltage, Current & Impedance on Antennas 16.3 Transmission Lines, Velocity Factor & SWR 16.4 Effective Radiated Power & Antenna Bandwidth

17 Element 3 Background: Propagation & Radio Practice

17.1 Radio Wave Propagation Modes 17.2 Multipath, Fading & Doppler Effects 17.3 Radio Practice, Interference & Good Engineering

18 Element 3: Aircraft Radio Navigation Systems

18.1 DME & VOR 18.2 ILS, ADF & ATC Transponders 18.3 Aircraft Antennas, Frequencies & Equipment Functions

19 Element 3: Installation, Maintenance & Repair

19.1 Indicating Meters & Meter Movements 19.2 Oscilloscopes & Waveform Measurement 19.3 Measurement Procedures 19.4 Installation Codes & Bonding Procedures 19.5 Frequency Standards, SINAD Meters & EMI Hunting 19.6 Spectrum Analyzers, TDRs & Service Monitors 19.7 Bench Repair Practices, ESD & Rework Tools 19.8 Systematic Troubleshooting & Field Fault Diagnosis

20 Element 3: Communications Technology & Marine Systems

20.1 Transmission Types, Coding & Multiplexing 20.2 Signal Processing, Software & Codes 20.3 Marine VHF, MF/HF & SSB-SITOR 20.4 Survival Craft Electronics, FAX & NAVTEX 20.5 NMEA 0183 & NMEA 2000 Data Networks

21 Element 3: RADAR & Satellite Systems

21.1 RADAR Theory & Pulse Fundamentals 21.2 Range, Pulse Width & PRF 21.3 Radar Antennas & Waveguides 21.4 INMARSAT Satellite Communications 21.5 RADAR Components: Magnetron, Duplexer, ATR & Synchro 21.6 RADAR Equipment, ARPA & Radiation Safety 21.7 Low Earth Orbit Systems: Iridium & COSPAS-SARSAT 21.8 GPS Satellite Navigation & DGPS

22 Element 3: RF & Electrical Safety

22.1 RF Radiation Exposure Limits 22.2 Electrical Safety Practices for Radio Technicians

23 Study Strategy & Exam Day

23.1 Study Strategy, Practice Plan & Exam Day

11.6 Positive & Negative Logic and Truth Tables

Key Takeaways Explain This Topic AI

In a positive-logic circuit the high level represents logic 1

In a negative-logic circuit the high level represents logic 0 - the convention is inverted, not the voltages

A truth table is a list of input combinations and their corresponding outputs that characterises a digital device's function

Trace a logic diagram gate by gate from the inputs, writing the level at each test point before moving on

  • The pool's figure-based items assume positive logic unless the question says otherwise
  • Last updated: August 2026

11.6 Positive & Negative Logic and Truth Tables

Quick Answer: Positive logic: HIGH = 1. Negative logic: HIGH = 0. A truth table is a list of input combinations and their corresponding outputs that characterises a device's function. Figure-based pool items assume positive logic and are solved by tracing gate by gate.

Sub-topic 3-E-035 (Logic Levels) splits cleanly into two halves: a pair of definition questions about logic convention, and three diagram-tracing questions where you must read levels at test points A, B and C.

Positive and negative logic

The voltage levels themselves never change. What changes is which voltage you agree to call a 1 .

  • Convention Logic 1 Logic 0
  • Positive logic High level Low level
  • Negative logic Low level High level

The pool asks both directions:

"In a positive-logic circuit, what level is used to represent a logic 1?" → High level.

"In a negative-logic circuit, what level is used to represent a logic 0?" → High level.

Read those two answers together and the symmetry is obvious: the answer is "high level" both times , because the second question asks about logic 0 under the inverted convention. Candidates who skim and answer "low level" for the second one have not noticed the digit changed.

Why negative logic exists

It is not perversity. Many real signals are active-low — a chip-select, a reset, an interrupt request, an enable — because a bipolar output sinks current far better than it sources it, so pulling a line down is the electrically stronger action. When a designer labels a pin RESET with an overbar, the assertion of that function is a low level, and describing that portion of the circuit in negative logic keeps the documentation honest.

A single gate can even be read two ways. A device that is a NAND in positive logic is a NOR in negative logic — the same silicon, described under two conventions. That duality is why schematics use bubbles on inputs and outputs to make the active level explicit rather than relying on the gate name alone.

Truth tables

What is a truth table? A list of input combinations and their corresponding outputs that characterizes a digital device's function.

Every word of that definition earns its place:

List of input combinations — every one of them. For n inputs there are 2ⁿ rows: 2 inputs → 4 rows, 3 inputs → 8 rows, 4 inputs → 16 rows.

Corresponding outputs — one output column per output.

Characterizes the function — the table is the specification. Two circuits with identical truth tables are functionally interchangeable however differently they are built.

The two-input basics, in positive logic:

  • A B AND OR NAND NOR XOR
  • 0 0 0 0 1 1 0
  • 0 1 0 1 1 0 1
  • 1 0 0 1 1 0 1
  • 1 1 1 1 0 0 0

Two memory hooks that survive exam pressure: AND is 1 only when everything is 1 ; OR is 0 only when everything is 0 . NAND and NOR are those two inverted, and XOR is 1 only when the inputs differ .

Tracing a logic diagram

Three of this sub-topic's six items show a figure and ask for the levels at test points A, B and C, assuming positive logic. There is no shortcut — but there is a reliable method:

Write the given input levels directly on the diagram as 1s and 0s. Do not hold them in your head.

Find every gate whose inputs are all known. Resolve those first, and write the result on its output line.

Repeat. Each pass makes more gates resolvable, and the wave moves left to right.

Account for every bubble. A bubble on an output inverts it; a bubble on an input inverts before the gate acts. Missing one bubble flips the whole downstream answer.

Only then read off A, B and C and match against the option set.

The most common failure is skipping step 1 and trying to trace mentally through three gate levels. Write it down. On a real exam sheet you have the diagram in front of you and nothing forbids annotating your scratch paper.

A worked pattern

Take a NAND whose inputs are high and low. AND of (1,0) is 0; the bubble inverts it to 1 . Feed that 1 plus another 1 into a second NAND: AND is 1, inverted to 0 . Feed that 0 into an inverter: output 1 . Three gates, three written intermediate values, no mental juggling.

Note that the pool's keyed answers for these items include combinations such as "A is low, B is high and C is high" and "A is high, B is high and C is high" — so do not assume the answer must have a mix of levels. Two of the three visible test points being identical is common.

  • Exam checklist
  • Positive logic → high = 1 ; negative logic → high = 0
  • Both convention questions key to "high level" — check which digit is being asked about
  • Truth table = all input combinations with their outputs , 2ⁿ rows
  • Diagram questions assume positive logic unless stated otherwise
  • Annotate the figure; resolve gates whose inputs are all known; respect every bubble