Study guide

11.5 TTL Logic Families & Input Voltage Levels

FCC General Radiotelephone Operator License GROL

Track your progress as you read

Finished sections get a check mark.

1 Introduction & GROL Exam Overview

1.1 About the General Radiotelephone Operator License 1.2 Exam Format, COLEMs, FRN & Application Process

2 Element 1: Rules & Regulations

2.1 Equipment Requirements (Part 80) 2.2 License Requirements & Operator Authority 2.3 Watchkeeping & Logkeeping Duties 2.4 Log Entries & Required Records 2.5 Ship Station Control, Inspections & International Rules

3 Element 1: Communications Procedures

3.1 Bridge-to-Bridge Operations & VTS 3.2 Distress Communications & Alerting 3.3 Operating Procedures, Calling & Testing 3.4 Urgency (PAN PAN) & Safety (SECURITE) Traffic 3.5 The GMDSS Concept & Ship Responsibilities

4 Element 1: Equipment Operations

4.1 VHF Equipment Controls 4.2 MF/HF SSB Equipment Controls 4.3 DSC Operations & Equipment Faults 4.4 VHF Channel Selection & Channel Assignments 4.5 MF/HF Frequency & Emission Selection 4.6 Required Equipment Tests & On-Air Test Procedure

5 Element 1: Other Equipment & Antennas

5.1 Marine Antennas & Polarization 5.2 EPIRBs & Emergency Beacons 5.3 Power Sources, Reserve Power & Required Tests 5.4 Search and Rescue Transponders (SARTs) 5.5 Survival Craft Portable VHF (SCT) Requirements 5.6 NAVTEX & Maritime Safety Information

6 Element 3: Electrical Principles

6.1 Electrical Elements, Units & Power Types 6.2 Magnetism & Magnetic Circuits 6.3 Resistance, Capacitance & Inductance 6.4 Waveforms & Semiconductor Introduction 6.5 Materials, Corrosion & Skin Effect 6.6 AC Measurement & Conversion Factors 6.7 Conduction, Reactive Power & Maximum Power Transfer

7 Element 3: Electrical Math

7.1 Ohm's Law — Series & Parallel Circuits 7.2 Frequency, Period, Wavelength & Waveform Math 7.3 Power Relationships & Decibels 7.4 RC/RL Time Constants 7.5 Frequency Counter Accuracy, PPM & Harmonics 7.6 Impedance in Rectangular & Polar Coordinates 7.7 Regulation, Turns Ratio, Zener Bias & Conductance

8 Element 3: Circuit Components — Passives & Power Devices

8.1 Capacitors & Photoconductive Devices 8.2 Transformers, Voltage Regulators & Zener Diodes 8.3 Diodes, SCRs & Triacs

9 Element 3: Active Components — Transistors & Devices

9.1 Bipolar Junction Transistors 9.2 FETs, LEDs & Specialty Devices 9.3 Device Selection, Ratings & Thermal Design

10 Element 3: Practical Circuits — RLC, Op Amps & Schematics

10.1 R-L-C Resonant Circuits 10.2 Op Amps, PLLs, VCOs & Mixers 10.3 Reading Schematics & Signal Flow

11 Element 3: Digital Logic

11.1 Logic Gates & Boolean Functions 11.2 Flip-Flops & Sequential Elements 11.3 Multivibrators & Timing Circuits 11.4 Microprocessors & Bus Architecture 11.5 TTL Logic Families & Input Voltage Levels 11.6 Positive & Negative Logic and Truth Tables 11.7 Memory Types & Microprocessor Concepts 11.8 Counters, Prescalers, BCD & Data Converters

12 Element 3: Receivers

12.1 Receiver Theory & Superheterodyne Architecture 12.2 RF Amplifiers & Front-End Design 12.3 Filters & Detectors 12.4 Audio, Squelch & Receiver Performance Specs 12.5 Receiver Oscillators: Colpitts, Hartley & Pierce 12.6 Mixing, Image Frequencies & Spurious Products 12.7 IF Selectivity & Filter Bandwidth

13 Element 3: Transmitters

13.1 RF Amplifier Classes & Efficiency 13.2 Oscillators, Modulators & Tuning Networks 13.3 SSB Transmitters & Modern Transmitter Technology

14 Element 3: Signals, Emissions & Modulation

14.1 Amplitude & Frequency Modulation 14.2 Single-Sideband Modulation 14.3 Pulse Modulation & Emission Types

15 Element 3: Power Sources

15.1 Batteries & Energy Storage 15.2 Motors, Generators & Power Supplies

16 Element 3: Antennas & Feed Lines

16.1 Antenna Theory, Types & Patterns 16.2 Voltage, Current & Impedance on Antennas 16.3 Transmission Lines, Velocity Factor & SWR 16.4 Effective Radiated Power & Antenna Bandwidth

17 Element 3 Background: Propagation & Radio Practice

17.1 Radio Wave Propagation Modes 17.2 Multipath, Fading & Doppler Effects 17.3 Radio Practice, Interference & Good Engineering

18 Element 3: Aircraft Radio Navigation Systems

18.1 DME & VOR 18.2 ILS, ADF & ATC Transponders 18.3 Aircraft Antennas, Frequencies & Equipment Functions

19 Element 3: Installation, Maintenance & Repair

19.1 Indicating Meters & Meter Movements 19.2 Oscilloscopes & Waveform Measurement 19.3 Measurement Procedures 19.4 Installation Codes & Bonding Procedures 19.5 Frequency Standards, SINAD Meters & EMI Hunting 19.6 Spectrum Analyzers, TDRs & Service Monitors 19.7 Bench Repair Practices, ESD & Rework Tools 19.8 Systematic Troubleshooting & Field Fault Diagnosis

20 Element 3: Communications Technology & Marine Systems

20.1 Transmission Types, Coding & Multiplexing 20.2 Signal Processing, Software & Codes 20.3 Marine VHF, MF/HF & SSB-SITOR 20.4 Survival Craft Electronics, FAX & NAVTEX 20.5 NMEA 0183 & NMEA 2000 Data Networks

21 Element 3: RADAR & Satellite Systems

21.1 RADAR Theory & Pulse Fundamentals 21.2 Range, Pulse Width & PRF 21.3 Radar Antennas & Waveguides 21.4 INMARSAT Satellite Communications 21.5 RADAR Components: Magnetron, Duplexer, ATR & Synchro 21.6 RADAR Equipment, ARPA & Radiation Safety 21.7 Low Earth Orbit Systems: Iridium & COSPAS-SARSAT 21.8 GPS Satellite Navigation & DGPS

22 Element 3: RF & Electrical Safety

22.1 RF Radiation Exposure Limits 22.2 Electrical Safety Practices for Radio Technicians

23 Study Strategy & Exam Day

23.1 Study Strategy, Practice Plan & Exam Day

11.5 TTL Logic Families & Input Voltage Levels

Key Takeaways Explain This Topic AI

TTL stands for transistor-transistor logic and runs from a 5-volt supply

A valid TTL logic low input at 5 volts is zero to 0.8 volts

A valid TTL logic high input at 5 volts is 2.0 to 5.5 volts

A TTL input left open floats to a high logic state, which is why unused inputs must be tied deliberately

  • A logic probe is the best instrument for checking a TTL logic circuit
  • Last updated: August 2026

11.5 TTL Logic Families & Input Voltage Levels

Quick Answer: TTL = transistor-transistor logic , supply 5 V . Valid low input = 0 to 0.8 V . Valid high input = 2.0 to 5.5 V . An open TTL input floats high . Best diagnostic instrument: a logic probe .

Sub-topic 3-E-033 (Types of Logic) is almost entirely about TTL numbers , and every one of them is a specific figure the pool asks directly. There is no reasoning path — learn the four values.

What TTL is

What do the initials TTL stand for? Transistor-transistor logic. The name describes the internal construction: bipolar transistors drive other bipolar transistors directly, with a multi-emitter input transistor as the characteristic front end. TTL dominated digital design for decades and remains the reference family the commercial pool tests against, even though CMOS displaced it in most new work.

What is the common power supply voltage for TTL series integrated circuits? 5 volts. Not 3.3 V, not 12 V, and not "whatever the design requires" — classic TTL is a 5-volt family, and its threshold voltages are defined relative to that rail.

The two voltage windows

This is the heart of the sub-topic:

  • Input state Valid range at a 5 V supply
  • Logic LOW 0 to 0.8 volts
  • Undefined (forbidden zone) above 0.8 V and below 2.0 V
  • Logic HIGH 2.0 to 5.5 volts

Three things to notice:

The windows are asymmetric. Low occupies only the bottom 0.8 V; high occupies everything from 2.0 V up. This reflects TTL's internal bipolar structure, which sinks current well and sources it poorly.

There is a forbidden band between 0.8 V and 2.0 V. A signal sitting there is neither a valid 0 nor a valid 1, and the gate's behaviour is undefined — it may oscillate, draw excess current, or interpret the input differently from one device to the next. A slow-rising signal crossing that band is a classic source of intermittent digital faults, and it is why Schmitt-trigger inputs exist.

The high window extends to 5.5 V, above the 5 V rail. That is a specification allowance, not an invitation — exceeding it damages the device.

The floating input

TTL inputs left open develop what logic state? A high-logic state.

Understand why, because the pool likes this one. A TTL input's multi-emitter transistor is internally pulled toward the positive rail; with nothing connected, no current is drawn out of the emitter, and the input behaves as though it were tied high.

But "floats high" is not the same as "safe to leave open." A floating TTL input is a high-impedance antenna. It will pick up noise from adjacent traces, switching supplies and nearby RF — the exact environment a GROL technician works in. The professional practice is unambiguous:

  • Unused input Correct treatment
  • Should be high Tie to Vcc through a 1 kΩ to 10 kΩ resistor (not directly, to limit fault current)
  • Should be low Tie directly to ground
  • Parallel gate not used Tie its inputs to a defined level anyway

Contrast CMOS, where a floating input has no defined state at all and may drift anywhere, causing both output transistors to conduct and the device to overheat. CMOS unused inputs must always be tied.

The right instrument

Which of the following instruments would be best for checking a TTL logic circuit? A logic probe.

A logic probe is a handheld tool with an LED or tone output that reports high , low , floating/invalid , and often pulsing at a point in a circuit. It is the right choice here for a specific reason: it interprets the signal against TTL thresholds and tells you which of the three regions the node is in — including the forbidden zone, which is exactly the fault a voltmeter obscures.

  • Instrument Why it is not the pool's answer
  • Analogue voltmeter Averages fast switching into a meaningless mid-scale reading

Oscilloscope Excellent for timing and edges, but slower to deploy for simple state checks and does not classify against logic thresholds

  • Signal generator Injects rather than measures
  • Logic probe Classifies the node as high, low, invalid, or pulsing — the answer

A logic pulser is the companion tool: it injects a brief pulse into a node so you can watch the downstream effect with the probe. Probe to observe, pulser to stimulate.

How this connects forward

The gate types themselves (AND, OR, NAND, NOR, XOR, inverter) belong to sub-topic 3-E-034 in section 11.1; the meaning of positive and negative logic and the reading of truth tables is 3-E-035 in section 11.6. This section is the electrical layer underneath both — the actual voltages that make a 1 a 1.