Study guide
7.6 Impedance in Rectangular & Polar Coordinates
FCC General Radiotelephone Operator License GROL
Track your progress as you read
Finished sections get a check mark.
1 Introduction & GROL Exam Overview
1.1 About the General Radiotelephone Operator License 1.2 Exam Format, COLEMs, FRN & Application Process
2 Element 1: Rules & Regulations
2.1 Equipment Requirements (Part 80) 2.2 License Requirements & Operator Authority 2.3 Watchkeeping & Logkeeping Duties 2.4 Log Entries & Required Records 2.5 Ship Station Control, Inspections & International Rules
3 Element 1: Communications Procedures
3.1 Bridge-to-Bridge Operations & VTS 3.2 Distress Communications & Alerting 3.3 Operating Procedures, Calling & Testing 3.4 Urgency (PAN PAN) & Safety (SECURITE) Traffic 3.5 The GMDSS Concept & Ship Responsibilities
4 Element 1: Equipment Operations
4.1 VHF Equipment Controls 4.2 MF/HF SSB Equipment Controls 4.3 DSC Operations & Equipment Faults 4.4 VHF Channel Selection & Channel Assignments 4.5 MF/HF Frequency & Emission Selection 4.6 Required Equipment Tests & On-Air Test Procedure
5 Element 1: Other Equipment & Antennas
5.1 Marine Antennas & Polarization 5.2 EPIRBs & Emergency Beacons 5.3 Power Sources, Reserve Power & Required Tests 5.4 Search and Rescue Transponders (SARTs) 5.5 Survival Craft Portable VHF (SCT) Requirements 5.6 NAVTEX & Maritime Safety Information
6 Element 3: Electrical Principles
6.1 Electrical Elements, Units & Power Types 6.2 Magnetism & Magnetic Circuits 6.3 Resistance, Capacitance & Inductance 6.4 Waveforms & Semiconductor Introduction 6.5 Materials, Corrosion & Skin Effect 6.6 AC Measurement & Conversion Factors 6.7 Conduction, Reactive Power & Maximum Power Transfer
7 Element 3: Electrical Math
7.1 Ohm's Law — Series & Parallel Circuits 7.2 Frequency, Period, Wavelength & Waveform Math 7.3 Power Relationships & Decibels 7.4 RC/RL Time Constants 7.5 Frequency Counter Accuracy, PPM & Harmonics 7.6 Impedance in Rectangular & Polar Coordinates 7.7 Regulation, Turns Ratio, Zener Bias & Conductance
8 Element 3: Circuit Components — Passives & Power Devices
8.1 Capacitors & Photoconductive Devices 8.2 Transformers, Voltage Regulators & Zener Diodes 8.3 Diodes, SCRs & Triacs
9 Element 3: Active Components — Transistors & Devices
9.1 Bipolar Junction Transistors 9.2 FETs, LEDs & Specialty Devices 9.3 Device Selection, Ratings & Thermal Design
10 Element 3: Practical Circuits — RLC, Op Amps & Schematics
10.1 R-L-C Resonant Circuits 10.2 Op Amps, PLLs, VCOs & Mixers 10.3 Reading Schematics & Signal Flow
11 Element 3: Digital Logic
11.1 Logic Gates & Boolean Functions 11.2 Flip-Flops & Sequential Elements 11.3 Multivibrators & Timing Circuits 11.4 Microprocessors & Bus Architecture 11.5 TTL Logic Families & Input Voltage Levels 11.6 Positive & Negative Logic and Truth Tables 11.7 Memory Types & Microprocessor Concepts 11.8 Counters, Prescalers, BCD & Data Converters
12 Element 3: Receivers
12.1 Receiver Theory & Superheterodyne Architecture 12.2 RF Amplifiers & Front-End Design 12.3 Filters & Detectors 12.4 Audio, Squelch & Receiver Performance Specs 12.5 Receiver Oscillators: Colpitts, Hartley & Pierce 12.6 Mixing, Image Frequencies & Spurious Products 12.7 IF Selectivity & Filter Bandwidth
13 Element 3: Transmitters
13.1 RF Amplifier Classes & Efficiency 13.2 Oscillators, Modulators & Tuning Networks 13.3 SSB Transmitters & Modern Transmitter Technology
14 Element 3: Signals, Emissions & Modulation
14.1 Amplitude & Frequency Modulation 14.2 Single-Sideband Modulation 14.3 Pulse Modulation & Emission Types
15 Element 3: Power Sources
15.1 Batteries & Energy Storage 15.2 Motors, Generators & Power Supplies
16 Element 3: Antennas & Feed Lines
16.1 Antenna Theory, Types & Patterns 16.2 Voltage, Current & Impedance on Antennas 16.3 Transmission Lines, Velocity Factor & SWR 16.4 Effective Radiated Power & Antenna Bandwidth
17 Element 3 Background: Propagation & Radio Practice
17.1 Radio Wave Propagation Modes 17.2 Multipath, Fading & Doppler Effects 17.3 Radio Practice, Interference & Good Engineering
18 Element 3: Aircraft Radio Navigation Systems
18.1 DME & VOR 18.2 ILS, ADF & ATC Transponders 18.3 Aircraft Antennas, Frequencies & Equipment Functions
19 Element 3: Installation, Maintenance & Repair
19.1 Indicating Meters & Meter Movements 19.2 Oscilloscopes & Waveform Measurement 19.3 Measurement Procedures 19.4 Installation Codes & Bonding Procedures 19.5 Frequency Standards, SINAD Meters & EMI Hunting 19.6 Spectrum Analyzers, TDRs & Service Monitors 19.7 Bench Repair Practices, ESD & Rework Tools 19.8 Systematic Troubleshooting & Field Fault Diagnosis
20 Element 3: Communications Technology & Marine Systems
20.1 Transmission Types, Coding & Multiplexing 20.2 Signal Processing, Software & Codes 20.3 Marine VHF, MF/HF & SSB-SITOR 20.4 Survival Craft Electronics, FAX & NAVTEX 20.5 NMEA 0183 & NMEA 2000 Data Networks
21 Element 3: RADAR & Satellite Systems
21.1 RADAR Theory & Pulse Fundamentals 21.2 Range, Pulse Width & PRF 21.3 Radar Antennas & Waveguides 21.4 INMARSAT Satellite Communications 21.5 RADAR Components: Magnetron, Duplexer, ATR & Synchro 21.6 RADAR Equipment, ARPA & Radiation Safety 21.7 Low Earth Orbit Systems: Iridium & COSPAS-SARSAT 21.8 GPS Satellite Navigation & DGPS
22 Element 3: RF & Electrical Safety
22.1 RF Radiation Exposure Limits 22.2 Electrical Safety Practices for Radio Technicians
23 Study Strategy & Exam Day
23.1 Study Strategy, Practice Plan & Exam Day
7.6 Impedance in Rectangular & Polar Coordinates
Key Takeaways Explain This Topic AI
Rectangular form writes impedance as R plus or minus jX, where a positive j term is inductive and a negative j term is capacitive
Inductive reactance is 2 pi f L and capacitive reactance is 1 divided by 2 pi f C - compute the reactance first, then attach the sign
A 0.1 microhenry inductor in series with 20 ohms at 30 MHz gives 20 + j19; a 1.0 millihenry inductor with 200 ohms at 30 kHz gives 200 + j188
Polar form gives magnitude and phase angle: 100 ohms of inductive reactance in series with 100 ohms of resistance is 141 ohms at +45 degrees
- A polar plot of a voltage in a sinewave circuit shows the magnitude and the phase angle
- Last updated: August 2026
7.6 Impedance in Rectangular & Polar Coordinates
Quick Answer: X_L = 2πfL , X_C = 1/(2πfC) . Rectangular: Z = R + jX_L or R − jX_C . Polar: |Z| = √(R² + X²) , θ = arctan(X/R) . Series 100 Ω R + 100 Ω X_L → 141 Ω ∠ +45° . Series 300 Ω R + 400 Ω X_C → 500 Ω ∠ −53.1° . A polar plot shows magnitude and phase angle .
Official sub-topics 3-B-016 (Impedance Networks-1) and 3-B-017 (Impedance Networks-2) are the same underlying task in two notations, which is why they cluster into one teaching section. Twelve pool questions ride on four formulas.
Step 1 — get the reactance
- Component Formula Sign in rectangular form
- Inductor X_L = 2πfL +j
- Capacitor X_C = 1/(2πfC) −j
The sign convention is worth fixing permanently: inductive is positive j, capacitive is negative j. "ELI the ICE man" is the classic aid — in an invert E r, vo L tage leads current I (inductive, +); in a C apacitor, current I leads voltage E (capacitive, −).
Step 2 — series networks in rectangular form
For components in series , just add: Z = R + jX .
Three worked pool items:
- 0.1 µH in series with 20 Ω at 30 MHz X_L = 2π × 30 × 10⁶ × 0.1 × 10⁻⁶ = 2π × 3 = 18.85 Ω → Z = 20 + j19
- 1.0 mH in series with 200 Ω at 30 kHz X_L = 2π × 30 × 10³ × 1 × 10⁻³ = 2π × 30 = 188.5 Ω → Z = 200 + j188
10 µH in series with 40 Ω at 500 MHz X_L = 2π × 500 × 10⁶ × 10 × 10⁻⁶ = 2π × 5000 = 31,416 Ω → Z = 40 + j31400 Note how completely the reactance swamps the resistance here: at 500 MHz a 10 µH
inductor is very nearly an open circuit, which is exactly why RF chokes work and why
you never see a 10 µH inductor used as a series element at UHF.
0.001 µF in series with 400 Ω at 500 kHz X_C = 1/(2π × 5 × 10⁵ × 1 × 10⁻⁹) = 1/(3.1416 × 10⁻³) = 318.3 Ω → Z = 400 − j318
The unit-prefix discipline
Nearly every wrong answer in this sub-topic comes from a prefix slip, not from the physics. Convert everything to base units before you touch the calculator:
- Prefix Symbol Multiplier
- pico pF 10⁻¹²
- nano nF 10⁻⁹
- micro µH, µF 10⁻⁶
- milli mH 10⁻³
- kilo kHz 10³
- mega MHz 10⁶
A useful sanity check: µH with MHz and mH with kHz both leave you multiplying by 2π and a small integer, because 10⁻⁶ × 10⁶ = 1 and 10⁻³ × 10³ = 1. If your answer is a factor of 1000 out, that is where it went.
Step 3 — parallel networks
Parallel is where candidates lose marks, because you cannot simply add. Use the product-over-sum rule with complex arithmetic, which is easiest in polar form:
0.01 µF in parallel with 300 Ω at 50 kHz X_C = 1/(2π × 5 × 10⁴ × 1 × 10⁻⁸) = 318.3 Ω Z = (300 × 318.3∠−90°) / (300 − j318.3)
- Denominator magnitude = √(300² + 318.3²) = 437.4, angle = −46.7°
- Z = 95,490 / 437.4 ∠ (−90° + 46.7°) = 218.3 ∠ −43.3°
- Convert back: 218.3 cos(−43.3°) = 159, 218.3 sin(−43.3°) = −150 → Z = 159 − j150
Note what happened: the resistive part of the answer, 159 Ω, is lower than the 300 Ω resistor. That is normal for a parallel network and is a useful check — a parallel combination is always smaller in magnitude than either branch alone.
Step 4 — polar form
|Z| = √(R² + X²) and θ = arctan(X / R) .
- Network Working Polar answer
- 100 Ω X_L series 100 Ω R √(100²+100²) = 141; arctan(100/100) = 45° 141 Ω ∠ +45°
- 400 Ω X_C series 300 Ω R √(300²+400²) = 500; arctan(−400/300) = −53.1° 500 Ω ∠ −53.1°
300 Ω X_C, 600 Ω X_L, 400 Ω R all series Net X = 600 − 300 = +300; √(400²+300²) = 500; arctan(300/400) = 36.9° 500 Ω ∠ +37°
400 Ω X_L parallel 300 Ω R (300 × 400∠90°)/(500∠53.1°) = 240 ∠ 36.9° 240 Ω ∠ +36.9°
Two habits that make these fast:
In a series circuit, combine reactances first. 600 Ω inductive and 300 Ω capacitive in series net to 300 Ω inductive — a single number — before you touch the resistance. That third row looks intimidating and is actually the 3-4-5 triangle.
Recognise the Pythagorean triples. 3-4-5 (300, 400, 500) and the 1-1-√2 case (100, 100, 141) cover most of the pool. If your magnitude is not landing on a clean number, re-check the arithmetic.
The sign of the angle tells you the character of the circuit: positive = net inductive, negative = net capacitive, zero = resonant or purely resistive (section 10.1).
What a polar plot shows
Using the polar coordinate system, what visual representation would you get of a voltage in a sinewave circuit? The plot shows the magnitude and phase angle.
That is the whole point of polar notation. Rectangular form (R + jX) tells you what the circuit is made of ; polar form (|Z| ∠ θ) tells you what it does — how big the opposition is and how far current lags or leads voltage. Both describe the same complex number, and converting between them is exactly the trigonometry above.