Study guide

7.1 Ohm's Law — Series & Parallel Circuits

FCC General Radiotelephone Operator License GROL

Track your progress as you read

Finished sections get a check mark.

1 Introduction & GROL Exam Overview

1.1 About the General Radiotelephone Operator License 1.2 Exam Format, COLEMs, FRN & Application Process

2 Element 1: Rules & Regulations

2.1 Equipment Requirements (Part 80) 2.2 License Requirements & Operator Authority 2.3 Watchkeeping & Logkeeping Duties 2.4 Log Entries & Required Records 2.5 Ship Station Control, Inspections & International Rules

3 Element 1: Communications Procedures

3.1 Bridge-to-Bridge Operations & VTS 3.2 Distress Communications & Alerting 3.3 Operating Procedures, Calling & Testing 3.4 Urgency (PAN PAN) & Safety (SECURITE) Traffic 3.5 The GMDSS Concept & Ship Responsibilities

4 Element 1: Equipment Operations

4.1 VHF Equipment Controls 4.2 MF/HF SSB Equipment Controls 4.3 DSC Operations & Equipment Faults 4.4 VHF Channel Selection & Channel Assignments 4.5 MF/HF Frequency & Emission Selection 4.6 Required Equipment Tests & On-Air Test Procedure

5 Element 1: Other Equipment & Antennas

5.1 Marine Antennas & Polarization 5.2 EPIRBs & Emergency Beacons 5.3 Power Sources, Reserve Power & Required Tests 5.4 Search and Rescue Transponders (SARTs) 5.5 Survival Craft Portable VHF (SCT) Requirements 5.6 NAVTEX & Maritime Safety Information

6 Element 3: Electrical Principles

6.1 Electrical Elements, Units & Power Types 6.2 Magnetism & Magnetic Circuits 6.3 Resistance, Capacitance & Inductance 6.4 Waveforms & Semiconductor Introduction 6.5 Materials, Corrosion & Skin Effect 6.6 AC Measurement & Conversion Factors 6.7 Conduction, Reactive Power & Maximum Power Transfer

7 Element 3: Electrical Math

7.1 Ohm's Law — Series & Parallel Circuits 7.2 Frequency, Period, Wavelength & Waveform Math 7.3 Power Relationships & Decibels 7.4 RC/RL Time Constants 7.5 Frequency Counter Accuracy, PPM & Harmonics 7.6 Impedance in Rectangular & Polar Coordinates 7.7 Regulation, Turns Ratio, Zener Bias & Conductance

8 Element 3: Circuit Components — Passives & Power Devices

8.1 Capacitors & Photoconductive Devices 8.2 Transformers, Voltage Regulators & Zener Diodes 8.3 Diodes, SCRs & Triacs

9 Element 3: Active Components — Transistors & Devices

9.1 Bipolar Junction Transistors 9.2 FETs, LEDs & Specialty Devices 9.3 Device Selection, Ratings & Thermal Design

10 Element 3: Practical Circuits — RLC, Op Amps & Schematics

10.1 R-L-C Resonant Circuits 10.2 Op Amps, PLLs, VCOs & Mixers 10.3 Reading Schematics & Signal Flow

11 Element 3: Digital Logic

11.1 Logic Gates & Boolean Functions 11.2 Flip-Flops & Sequential Elements 11.3 Multivibrators & Timing Circuits 11.4 Microprocessors & Bus Architecture 11.5 TTL Logic Families & Input Voltage Levels 11.6 Positive & Negative Logic and Truth Tables 11.7 Memory Types & Microprocessor Concepts 11.8 Counters, Prescalers, BCD & Data Converters

12 Element 3: Receivers

12.1 Receiver Theory & Superheterodyne Architecture 12.2 RF Amplifiers & Front-End Design 12.3 Filters & Detectors 12.4 Audio, Squelch & Receiver Performance Specs 12.5 Receiver Oscillators: Colpitts, Hartley & Pierce 12.6 Mixing, Image Frequencies & Spurious Products 12.7 IF Selectivity & Filter Bandwidth

13 Element 3: Transmitters

13.1 RF Amplifier Classes & Efficiency 13.2 Oscillators, Modulators & Tuning Networks 13.3 SSB Transmitters & Modern Transmitter Technology

14 Element 3: Signals, Emissions & Modulation

14.1 Amplitude & Frequency Modulation 14.2 Single-Sideband Modulation 14.3 Pulse Modulation & Emission Types

15 Element 3: Power Sources

15.1 Batteries & Energy Storage 15.2 Motors, Generators & Power Supplies

16 Element 3: Antennas & Feed Lines

16.1 Antenna Theory, Types & Patterns 16.2 Voltage, Current & Impedance on Antennas 16.3 Transmission Lines, Velocity Factor & SWR 16.4 Effective Radiated Power & Antenna Bandwidth

17 Element 3 Background: Propagation & Radio Practice

17.1 Radio Wave Propagation Modes 17.2 Multipath, Fading & Doppler Effects 17.3 Radio Practice, Interference & Good Engineering

18 Element 3: Aircraft Radio Navigation Systems

18.1 DME & VOR 18.2 ILS, ADF & ATC Transponders 18.3 Aircraft Antennas, Frequencies & Equipment Functions

19 Element 3: Installation, Maintenance & Repair

19.1 Indicating Meters & Meter Movements 19.2 Oscilloscopes & Waveform Measurement 19.3 Measurement Procedures 19.4 Installation Codes & Bonding Procedures 19.5 Frequency Standards, SINAD Meters & EMI Hunting 19.6 Spectrum Analyzers, TDRs & Service Monitors 19.7 Bench Repair Practices, ESD & Rework Tools 19.8 Systematic Troubleshooting & Field Fault Diagnosis

20 Element 3: Communications Technology & Marine Systems

20.1 Transmission Types, Coding & Multiplexing 20.2 Signal Processing, Software & Codes 20.3 Marine VHF, MF/HF & SSB-SITOR 20.4 Survival Craft Electronics, FAX & NAVTEX 20.5 NMEA 0183 & NMEA 2000 Data Networks

21 Element 3: RADAR & Satellite Systems

21.1 RADAR Theory & Pulse Fundamentals 21.2 Range, Pulse Width & PRF 21.3 Radar Antennas & Waveguides 21.4 INMARSAT Satellite Communications 21.5 RADAR Components: Magnetron, Duplexer, ATR & Synchro 21.6 RADAR Equipment, ARPA & Radiation Safety 21.7 Low Earth Orbit Systems: Iridium & COSPAS-SARSAT 21.8 GPS Satellite Navigation & DGPS

22 Element 3: RF & Electrical Safety

22.1 RF Radiation Exposure Limits 22.2 Electrical Safety Practices for Radio Technicians

23 Study Strategy & Exam Day

23.1 Study Strategy, Practice Plan & Exam Day

7.1 Ohm's Law — Series & Parallel Circuits

Key Takeaways Explain This Topic AI

Ohm’s Law states V = IR (also I = V/R and R = V/I); voltage, current, and resistance are locked together in every resistive network you analyze on Element 3

In a series circuit the same current flows through every element and the voltage drops add to the source; total resistance is the sum of the individual resistances

In a parallel circuit every branch sees the same voltage and the branch currents add to the total current; equivalent resistance is always less than the smallest branch

Equal resistors in parallel: n identical R’s give R/n; two unequal resistors use the product-over-sum formula Req = (R1 R2)/(R1 + R2)

Voltage dividers set intermediate DC/AC potentials from a string of series resistors: Vout = Vin × (Rbottom / Rtotal) when the load does not load the divider heavily

Last updated: August 2026

7.1 Ohm's Law — Series & Parallel Circuits

Quick Answer: V = IR . Series: current is the same everywhere; voltages add ; R_total = R1 + R2 + … . Parallel: voltage is the same across every branch; currents add ; 1/Req = 1/R1 + 1/R2 + … (two resistors: Req = R1 R2 / (R1 + R2) ). A voltage divider yields Vout = Vin × (R_lower / R_total) .

Element 3 Topic 3-B (key topics roughly 009–018 ) is the quantitative core of general radiotelephone theory. Before you can size loads, bias stages, or reason about RF networks, you must compute resistive circuits the way a bench tech does—with Ohm’s Law and series/parallel combination rules that never change.

Ohm’s Law in three forms

Georg Ohm’s relationship for a pure resistance (or the resistive part of a network) is: V = I R I = V R R = V I V = I R \qquad I = \frac{V}{R} \qquad R = \frac{V}{I} V = I R I = R V ​ R = I V ​

  • Known Solve for Formula
  • I and R Voltage (V = IR)
  • V and R Current (I = V/R)
  • V and I Resistance (R = V/I)

Units: volts (V), amperes (A), ohms (Ω). Keep prefixes consistent: milliamps with kilohms often cancel neatly ( I m A = V / R k Ω I\,\mathrm{mA} = V / R_{\mathrm{k}\Omega} I mA = V / R k Ω ​ ).

Worked example — classic pool arithmetic

What current flows through a 50 Ω resistor with 100 V applied? I = V R = 100 V 50 Ω = 2 A I = \frac{V}{R} = \frac{100\,\mathrm{V}}{50\,\Omega} = 2\,\mathrm{A} I = R V ​ = 50 Ω 100 V ​ = 2 A

Trap answers on Element 3 style stems include 0.5 A (inverted formula), 5 A (misread 100/20), or absurd 5000 A (unit mix-ups). Always write the formula first, then substitute.

Worked example — finding R from meter readings

A resistor drops 12 V while carrying 40 mA . What is R? R = 12 0.040 = 300 Ω R = \frac{12}{0.040} = 300\,\Omega R = 0.040 12 ​ = 300 Ω

Convert milliamps to amperes before dividing, or use R = 12 / 40 m A = 0.3 k Ω = 300 Ω R = 12 / 40\,\mathrm{mA} = 0.3\,\mathrm{k}\Omega = 300\,\Omega R = 12/40 mA = 0.3 k Ω = 300 Ω .

Series circuits — same current, voltages add

In a series connection there is one path for current. Therefore:

Current is the same through every series element.

Voltage drops add to equal the source: V s = V 1 + V 2 + ⋯ V_s = V_1 + V_2 + \cdots V s ​ = V 1 ​ + V 2 ​ + ⋯ .

Total resistance is the sum : R T = R 1 + R 2 + ⋯ R_T = R_1 + R_2 + \cdots R T ​ = R 1 ​ + R 2 ​ + ⋯ .

Each voltage drop is V n = I R n V_n = I R_n V n ​ = I R n ​ with the same I.

  • Series rule Statement
  • Current Identical in every element
  • Voltage Individual drops sum to source
  • Resistance Algebraic sum of ohms
  • Power Individual powers sum to total power
  • Worked example — three series resistors

A 24 V supply feeds R1 = 100 Ω , R2 = 200 Ω , and R3 = 300 Ω in series.

R T = 100 + 200 + 300 = 600 Ω R_T = 100 + 200 + 300 = 600\,\Omega R T ​ = 100 + 200 + 300 = 600 Ω

I = 24 / 600 = 0.040 A = 40 m A I = 24 / 600 = 0.040\,\mathrm{A} = 40\,\mathrm{mA} I = 24/600 = 0.040 A = 40 mA

Drops: V 1 = 4 V V_1 = 4\,\mathrm{V} V 1 ​ = 4 V , V 2 = 8 V V_2 = 8\,\mathrm{V} V 2 ​ = 8 V , V 3 = 12 V V_3 = 12\,\mathrm{V} V 3 ​ = 12 V (sum = 24 V)

Notice the voltage shares the same proportions as the resistances (100:200:300 = 1:2:3). That proportion is exactly the voltage-divider idea below.

Parallel circuits — same voltage, currents add

In a parallel connection every branch is connected across the same two nodes . Therefore:

Voltage is the same across every parallel branch.

Branch currents add to the total source current: I T = I 1 + I 2 + ⋯ I_T = I_1 + I_2 + \cdots I T ​ = I 1 ​ + I 2 ​ + ⋯ .

Equivalent resistance satisfies: 1 R e q = 1 R 1 + 1 R 2 + ⋯ \frac{1}{R_{eq}} = \frac{1}{R_1} + \frac{1}{R_2} + \cdots R e q ​ 1 ​ = R 1 ​ 1 ​ + R 2 ​ 1 ​ + ⋯

For two resistors: R e q = R 1 R 2 R 1 + R 2 R_{eq} = \frac{R_1 R_2}{R_1 + R_2} R e q ​ = R 1 ​ + R 2 ​ R 1 ​ R 2 ​ ​

Critical exam fact: R e q R_{eq} R e q ​ of a parallel group is always less than the smallest individual resistor in that group. If someone offers an answer larger than the smallest R, reject it.

  • Equal resistors shortcut
  • n identical resistors of value R in parallel: R e q = R n R_{eq} = \frac{R}{n} R e q ​ = n R ​

Three 30 Ω resistors in parallel: R e q = 30 3 = 10 Ω R_{eq} = \frac{30}{3} = 10\,\Omega R e q ​ = 3 30 ​ = 10 Ω

That exact pattern appears in Element 3-style practice: equal values → divide by count. Trap options often list the series sum (90 Ω) or a product (270 Ω).

Worked example — two unequal parallels

R1 = 60 Ω and R2 = 40 Ω in parallel across 12 V :

R e q = ( 60 × 40 ) / ( 60 + 40 ) = 2400 / 100 = 24 Ω R_{eq} = (60 \times 40)/(60 + 40) = 2400/100 = 24\,\Omega R e q ​ = ( 60 × 40 ) / ( 60 + 40 ) = 2400/100 = 24 Ω

I T = 12 / 24 = 0.5 A I_T = 12 / 24 = 0.5\,\mathrm{A} I T ​ = 12/24 = 0.5 A

Branch currents: I 1 = 12 / 60 = 0.2 A I_1 = 12/60 = 0.2\,\mathrm{A} I 1 ​ = 12/60 = 0.2 A , I 2 = 12 / 40 = 0.3 A I_2 = 12/40 = 0.3\,\mathrm{A} I 2 ​ = 12/40 = 0.3 A (sum 0.5 A)

Series–parallel combinations

Real schematics mix both topologies. Method:

Collapse pure series groups into one equivalent.

Collapse pure parallel groups into one equivalent.

Repeat until one equivalent resistance remains; then apply Ohm’s Law to find total current; finally back-substitute for branch currents and drops.

Worked example — series with a parallel pair

A 48 V source feeds R1 = 20 Ω in series with the parallel combination of R2 = 60 Ω and R3 = 30 Ω .

Parallel pair: R 23 = ( 60 × 30 ) / ( 60 + 30 ) = 20 Ω R_{23} = (60 \times 30)/(60 + 30) = 20\,\Omega R 23 ​ = ( 60 × 30 ) / ( 60 + 30 ) = 20 Ω

  • Total: R T = 20 + 20 = 40 Ω R_T = 20 + 20 = 40\,\Omega R T ​ = 20 + 20 = 40 Ω
  • I T = 48 / 40 = 1.2 A I_T = 48/40 = 1.2\,\mathrm{A} I T ​ = 48/40 = 1.2 A

Drop on R1: V 1 = 1.2 × 20 = 24 V V_1 = 1.2 \times 20 = 24\,\mathrm{V} V 1 ​ = 1.2 × 20 = 24 V ; remaining 24 V appears across the parallel pair.

Currents: I 2 = 24 / 60 = 0.4 A I_2 = 24/60 = 0.4\,\mathrm{A} I 2 ​ = 24/60 = 0.4 A , I 3 = 24 / 30 = 0.8 A I_3 = 24/30 = 0.8\,\mathrm{A} I 3 ​ = 24/30 = 0.8 A .

Voltage dividers

A string of series resistors across a source creates intermediate voltages. For a two-resistor divider with R_top toward the high side and R_bottom toward ground (unloaded): V o u t = V i n × R b o t t o m R t o p + R b o t t o m V_{out} = V_{in} \times \frac{R_{bottom}}{R_{top} + R_{bottom}} V o u t ​ = V in ​ × R t o p ​ + R b o tt o m ​ R b o tt o m ​ ​

  • Goal How the divider helps
  • Bias a transistor base Set DC operating point from a supply rail
  • Scale a sensor voltage Feed an ADC or meter within range
  • Reference for comparators Fixed fraction of a regulated supply
  • Worked example — unloaded divider

V i n = 15 V V_{in} = 15\,\mathrm{V} V in ​ = 15 V , R t o p = 2 k Ω R_{top} = 2\,\mathrm{k}\Omega R t o p ​ = 2 k Ω , R b o t t o m = 1 k Ω R_{bottom} = 1\,\mathrm{k}\Omega R b o tt o m ​ = 1 k Ω : V o u t = 15 × 1 2 + 1 = 5 V V_{out} = 15 \times \frac{1}{2+1} = 5\,\mathrm{V} V o u t ​ = 15 × 2 + 1 1 ​ = 5 V

Loading warning: if a low-resistance load is placed across R b o t t o m R_{bottom} R b o tt o m ​ , the parallel combination lowers the bottom resistance and pulls Vout down . For exam estimation, either assume “no load” as the stem states, or recompute the parallel of R b o t t o m R_{bottom} R b o tt o m ​ and R l o a d R_{load} R l o a d ​ first.

Current dividers (parallel dual)

Two resistors in parallel share current inversely with resistance: I 1 = I T × R 2 R 1 + R 2 I_1 = I_T \times \frac{R_2}{R_1 + R_2} I 1 ​ = I T ​ × R 1 ​ + R 2 ​ R 2 ​ ​

The smaller resistor takes the larger share of current—same physics as Ohm’s Law at equal voltage.

Power in resistive networks (preview of §7.3)

Once you know V and I (or I and R, or V and R), local dissipation is: P = V I = I 2 R = V 2 R P = VI = I^2 R = \frac{V^2}{R} P = V I = I 2 R = R V 2 ​

In series, the largest resistor dissipates the most power (same I, larger R). In parallel, the smallest resistor dissipates the most power (same V, smaller R → larger I and larger V 2 / R V^2/R V 2 / R ).

Exam-day checklist for §7.1

Write V = IR and rearrange only after labeling knowns.

Ask: series or parallel? Same I vs same V is the fork.

Series total R = sum ; parallel equal R’s → R/n ; two unequal → product/sum .

Parallel Req must be < smallest R .

Voltage divider: fraction of total R on the bottom leg (unloaded).

Back-check: series voltages sum to source; parallel currents sum to total.

Master these six checks and you clear the Ohm’s-Law and network slice of Topic 3-B before moving into frequency, wavelength, and waveform amplitude math.