Study guide

7.3 Power Relationships & Decibels

FCC General Radiotelephone Operator License GROL

Track your progress as you read

Finished sections get a check mark.

1 Introduction & GROL Exam Overview

1.1 About the General Radiotelephone Operator License 1.2 Exam Format, COLEMs, FRN & Application Process

2 Element 1: Rules & Regulations

2.1 Equipment Requirements (Part 80) 2.2 License Requirements & Operator Authority 2.3 Watchkeeping & Logkeeping Duties 2.4 Log Entries & Required Records 2.5 Ship Station Control, Inspections & International Rules

3 Element 1: Communications Procedures

3.1 Bridge-to-Bridge Operations & VTS 3.2 Distress Communications & Alerting 3.3 Operating Procedures, Calling & Testing 3.4 Urgency (PAN PAN) & Safety (SECURITE) Traffic 3.5 The GMDSS Concept & Ship Responsibilities

4 Element 1: Equipment Operations

4.1 VHF Equipment Controls 4.2 MF/HF SSB Equipment Controls 4.3 DSC Operations & Equipment Faults 4.4 VHF Channel Selection & Channel Assignments 4.5 MF/HF Frequency & Emission Selection 4.6 Required Equipment Tests & On-Air Test Procedure

5 Element 1: Other Equipment & Antennas

5.1 Marine Antennas & Polarization 5.2 EPIRBs & Emergency Beacons 5.3 Power Sources, Reserve Power & Required Tests 5.4 Search and Rescue Transponders (SARTs) 5.5 Survival Craft Portable VHF (SCT) Requirements 5.6 NAVTEX & Maritime Safety Information

6 Element 3: Electrical Principles

6.1 Electrical Elements, Units & Power Types 6.2 Magnetism & Magnetic Circuits 6.3 Resistance, Capacitance & Inductance 6.4 Waveforms & Semiconductor Introduction 6.5 Materials, Corrosion & Skin Effect 6.6 AC Measurement & Conversion Factors 6.7 Conduction, Reactive Power & Maximum Power Transfer

7 Element 3: Electrical Math

7.1 Ohm's Law — Series & Parallel Circuits 7.2 Frequency, Period, Wavelength & Waveform Math 7.3 Power Relationships & Decibels 7.4 RC/RL Time Constants 7.5 Frequency Counter Accuracy, PPM & Harmonics 7.6 Impedance in Rectangular & Polar Coordinates 7.7 Regulation, Turns Ratio, Zener Bias & Conductance

8 Element 3: Circuit Components — Passives & Power Devices

8.1 Capacitors & Photoconductive Devices 8.2 Transformers, Voltage Regulators & Zener Diodes 8.3 Diodes, SCRs & Triacs

9 Element 3: Active Components — Transistors & Devices

9.1 Bipolar Junction Transistors 9.2 FETs, LEDs & Specialty Devices 9.3 Device Selection, Ratings & Thermal Design

10 Element 3: Practical Circuits — RLC, Op Amps & Schematics

10.1 R-L-C Resonant Circuits 10.2 Op Amps, PLLs, VCOs & Mixers 10.3 Reading Schematics & Signal Flow

11 Element 3: Digital Logic

11.1 Logic Gates & Boolean Functions 11.2 Flip-Flops & Sequential Elements 11.3 Multivibrators & Timing Circuits 11.4 Microprocessors & Bus Architecture 11.5 TTL Logic Families & Input Voltage Levels 11.6 Positive & Negative Logic and Truth Tables 11.7 Memory Types & Microprocessor Concepts 11.8 Counters, Prescalers, BCD & Data Converters

12 Element 3: Receivers

12.1 Receiver Theory & Superheterodyne Architecture 12.2 RF Amplifiers & Front-End Design 12.3 Filters & Detectors 12.4 Audio, Squelch & Receiver Performance Specs 12.5 Receiver Oscillators: Colpitts, Hartley & Pierce 12.6 Mixing, Image Frequencies & Spurious Products 12.7 IF Selectivity & Filter Bandwidth

13 Element 3: Transmitters

13.1 RF Amplifier Classes & Efficiency 13.2 Oscillators, Modulators & Tuning Networks 13.3 SSB Transmitters & Modern Transmitter Technology

14 Element 3: Signals, Emissions & Modulation

14.1 Amplitude & Frequency Modulation 14.2 Single-Sideband Modulation 14.3 Pulse Modulation & Emission Types

15 Element 3: Power Sources

15.1 Batteries & Energy Storage 15.2 Motors, Generators & Power Supplies

16 Element 3: Antennas & Feed Lines

16.1 Antenna Theory, Types & Patterns 16.2 Voltage, Current & Impedance on Antennas 16.3 Transmission Lines, Velocity Factor & SWR 16.4 Effective Radiated Power & Antenna Bandwidth

17 Element 3 Background: Propagation & Radio Practice

17.1 Radio Wave Propagation Modes 17.2 Multipath, Fading & Doppler Effects 17.3 Radio Practice, Interference & Good Engineering

18 Element 3: Aircraft Radio Navigation Systems

18.1 DME & VOR 18.2 ILS, ADF & ATC Transponders 18.3 Aircraft Antennas, Frequencies & Equipment Functions

19 Element 3: Installation, Maintenance & Repair

19.1 Indicating Meters & Meter Movements 19.2 Oscilloscopes & Waveform Measurement 19.3 Measurement Procedures 19.4 Installation Codes & Bonding Procedures 19.5 Frequency Standards, SINAD Meters & EMI Hunting 19.6 Spectrum Analyzers, TDRs & Service Monitors 19.7 Bench Repair Practices, ESD & Rework Tools 19.8 Systematic Troubleshooting & Field Fault Diagnosis

20 Element 3: Communications Technology & Marine Systems

20.1 Transmission Types, Coding & Multiplexing 20.2 Signal Processing, Software & Codes 20.3 Marine VHF, MF/HF & SSB-SITOR 20.4 Survival Craft Electronics, FAX & NAVTEX 20.5 NMEA 0183 & NMEA 2000 Data Networks

21 Element 3: RADAR & Satellite Systems

21.1 RADAR Theory & Pulse Fundamentals 21.2 Range, Pulse Width & PRF 21.3 Radar Antennas & Waveguides 21.4 INMARSAT Satellite Communications 21.5 RADAR Components: Magnetron, Duplexer, ATR & Synchro 21.6 RADAR Equipment, ARPA & Radiation Safety 21.7 Low Earth Orbit Systems: Iridium & COSPAS-SARSAT 21.8 GPS Satellite Navigation & DGPS

22 Element 3: RF & Electrical Safety

22.1 RF Radiation Exposure Limits 22.2 Electrical Safety Practices for Radio Technicians

23 Study Strategy & Exam Day

23.1 Study Strategy, Practice Plan & Exam Day

7.3 Power Relationships & Decibels

Key Takeaways Explain This Topic AI

Resistive/DC power: P = VI = I²R = V²/R; use consistent RMS values for sine-wave AC true power in resistors

Peak Envelope Power (PEP) is the average power during one RF cycle at the crest of the modulation envelope—not the same as long-term average power of a modulated signal

Power ratios in decibels: dB = 10 log10(P2/P1); voltage (or current) ratios in the same impedance: dB = 20 log10(V2/V1)

Memory anchors: +3 dB ≈ ×2 power; −3 dB ≈ ×½ power; +6 dB ≈ ×2 voltage (×4 power); +10 dB = ×10 power; +20 dB = ×100 power

Gains and losses in a cascade add in dB (or multiply as linear ratios); attenuators reduce power by a known dB amount

Last updated: August 2026

7.3 Power Relationships & Decibels

Quick Answer: P = VI = I²R = V²/R . PEP is average power at the envelope crest , not the long-term average of a keyed/modulated signal. dB (power) = 10 log(P2/P1) ; dB (voltage) = 20 log(V2/V1) at constant Z. +3 dB ≈ double power ; +6 dB ≈ double voltage .

Topic 3-B power questions mix bench DC formulas with RF concepts (PEP) and logarithmic ratios (dB). GROL techs use all three daily: supply loading, transmitter output, and gain/loss budgets.

Three forms of electrical power

For a resistance R carrying current I with voltage V across it: P = V I = I 2 R = V 2 R P = V I = I^2 R = \frac{V^2}{R} P = V I = I 2 R = R V 2 ​

  • Formula Best when you know
  • (P = VI) Both voltage and current
  • P = I 2 R P = I^2 R P = I 2 R Current and resistance
  • P = V 2 / R P = V^2 / R P = V 2 / R Voltage and resistance

DC circuit pool form: the formula for power is P = V × I (among the three equivalents). On pure resistance, all three agree.

Worked example — resistor dissipation

A 50 Ω dummy load shows 100 V RMS RF (sine, properly metered): P = V 2 R = 100 2 50 = 200 W P = \frac{V^2}{R} = \frac{100^2}{50} = 200\,\mathrm{W} P = R V 2 ​ = 50 10 0 2 ​ = 200 W

Alternatively, I = V / R = 2 A I = V/R = 2\,\mathrm{A} I = V / R = 2 A , so P = V I = 200 W P = VI = 200\,\mathrm{W} P = V I = 200 W or P = I 2 R = 4 × 50 = 200 W P = I^2 R = 4 \times 50 = 200\,\mathrm{W} P = I 2 R = 4 × 50 = 200 W .

Worked example — series power split

12 V across series R1 = 4 Ω and R2 = 8 Ω :

R T = 12 Ω R_T = 12\,\Omega R T ​ = 12 Ω , I = 1 A I = 1\,\mathrm{A} I = 1 A

P 1 = I 2 R 1 = 4 W P_1 = I^2 R_1 = 4\,\mathrm{W} P 1 ​ = I 2 R 1 ​ = 4 W , P 2 = 8 W P_2 = 8\,\mathrm{W} P 2 ​ = 8 W , total 12 W (also P = V I = 12 × 1 P = VI = 12 \times 1 P = V I = 12 × 1 )

Larger series R dissipates more power at the same current.

Apparent, true, and reactive power (callback)

From Chapter 6: on AC with phase shift, V_RMS × I_RMS is apparent power (VA) ; true power (W) is S × P F S \times \mathrm{PF} S × PF or I 2 R I^2 R I 2 R in resistive parts; reactive power (VAR) is the out-of-phase L/C component. Section 7.3’s P = VI for DC/resistive sine heating still holds for true power when V and I are the resistive-component values or when PF is included.

Peak Envelope Power (PEP) vs average power

Peak Envelope Power (PEP) is the average power supplied to the antenna transmission line by a transmitter during one RF cycle at the crest of the modulation envelope . Read that carefully:

It is not the instantaneous peak of a single RF sine sample without the “average over one RF cycle” idea.

It is not automatically the long-term average power of SSB speech or CW keying.

For a steady unmodulated carrier (CW key-down, constant envelope), PEP equals the continuous average power.

For SSB voice , PEP is set by the loudest envelope peaks; long-term average power is lower (depends on voice, compression, and duty of speech).

  • Signal PEP vs long-term average
  • Unmodulated carrier Essentially equal
  • AM 100% modulated PEP higher than carrier power (classic 4× carrier for ideal full AM envelope peaks)
  • SSB voice PEP is the regulatory/spec number; average much lower
  • Pulsed RF Average ≈ PEP × duty cycle (if off power ≈ 0)
  • Worked example — pulse average from PEP

Transmitter PEP = 100 W during a pulse; duty cycle 20% ; off power negligible: P a v g ≈ 100 × 0.20 = 20 W P_{\mathrm{avg}} \approx 100 \times 0.20 = 20\,\mathrm{W} P avg ​ ≈ 100 × 0.20 = 20 W

That average matters for power-supply sizing and thermal design even when the plate/license discussion quotes PEP.

Decibels — power ratios

The decibel expresses a ratio , not an absolute unit by itself (unless referenced: dBm, dBW, etc.).

Power ratio: d B = 10 log ⁡ 10 ( P 2 P 1 ) \mathrm{dB} = 10 \log_{10}\left(\frac{P_2}{P_1}\right) dB = 10 lo g 10 ​ ( P 1 ​ P 2 ​ ​ )

  • Power ratio P2/P1 dB
  • 2 ≈ +3 dB
  • 4 ≈ +6 dB
  • 10 +10 dB
  • 100 +20 dB
  • 0.5 ≈ −3 dB
  • 0.1 −10 dB
  • 0.01 −20 dB
  • Worked example — amplifier gain (pool style)

Input 0.5 mW , output 50 mW : P 2 P 1 = 50 0.5 = 100 ⇒ 10 log ⁡ 10 ( 100 ) = 20 d B \frac{P_2}{P_1} = \frac{50}{0.5} = 100 \Rightarrow 10 \log_{10}(100) = 20\,\mathrm{dB} P 1 ​ P 2 ​ ​ = 0.5 50 ​ = 100 ⇒ 10 lo g 10 ​ ( 100 ) = 20 dB

Trap answers: 10 dB (forgot the ratio is 100, not 10), 100 dB (confused linear ratio with dB), 17 dB (mis-log).

Worked example — half power

A filter’s cutoff is often specified at −3 dB , meaning output power is about half the midband power (−3 dB ≈ 10 log(0.5)).

Decibels — voltage and current ratios

When comparing voltages (or currents) across the same impedance : d B = 20 log ⁡ 10 ( V 2 V 1 ) = 20 log ⁡ 10 ( I 2 I 1 ) \mathrm{dB} = 20 \log_{10}\left(\frac{V_2}{V_1}\right) = 20 \log_{10}\left(\frac{I_2}{I_1}\right) dB = 20 lo g 10 ​ ( V 1 ​ V 2 ​ ​ ) = 20 lo g 10 ​ ( I 1 ​ I 2 ​ ​ )

Why 20? Because power scales with V² (or I²) at fixed R, so 10 log(V² ratio) = 20 log(V ratio).

  • Voltage ratio V2/V1 dB
  • 2 ≈ +6 dB
  • 10 +20 dB
  • 0.5 ≈ −6 dB
  • 100 +40 dB

Memory hooks Element 3 loves:

  • 3 dB ↔ factor-of-two power
  • 6 dB ↔ factor-of-two voltage (and four times power)
  • 10 dB ↔ ×10 power
  • 20 dB ↔ ×100 power or ×10 voltage
  • Worked example — voltage gain to dB

Amplifier voltage gain ×10 into matched Z: 20 log ⁡ 10 ( 10 ) = 20 d B 20 \log_{10}(10) = 20\,\mathrm{dB} 20 lo g 10 ​ ( 10 ) = 20 dB

Power gain is also ×100 → 20 dB when Z is the same—consistent story.

Cascaded gains and losses

In decibels , stage gains and losses add : G t o t a l , d B = G 1 + G 2 + G 3 + ⋯ G_{\mathrm{total,dB}} = G_1 + G_2 + G_3 + \cdots G total , dB ​ = G 1 ​ + G 2 ​ + G 3 ​ + ⋯

(Negative numbers for attenuators and line loss.)

In linear ratios , you multiply .

Worked example — RF chain budget

  • Stage Gain/loss
  • Preamplifier +12 dB
  • Filter −2 dB
  • Cable −3 dB
  • Power amp +20 dB

Total: 12 − 2 − 3 + 20 = + 27 d B 12 - 2 - 3 + 20 = +27\,\mathrm{dB} 12 − 2 − 3 + 20 = + 27 dB .

If Pin = 1 mW (0 dBm), Pout ≈ 27 dBm = 0.5 W (because 30 dBm = 1 W, 27 dBm is 3 dB less → half a watt).

Attenuators

An RF attenuator reduces signal power by a known amount (fixed pad or step attenuator). Purpose is level control, protection, and measurement—not frequency conversion or demodulation. A 10 dB pad multiplies power by 0.1 and multiplies voltage (same Z) by ≈ 0.316 .

Absolute decibel references (useful, not always tested)

  • Unit Reference
  • dBm 1 mW
  • dBW 1 W
  • dBV 1 V
  • dBµV 1 µV

Conversion example: 30 dBm = 1 W = 0 dBW . 0 dBm = 1 mW .

Exam-day checklist for §7.3

Pick the convenient P form: VI, I²R, or V²/R.

PEP = average power of one RF cycle at the envelope peak .

Power dB → 10 log ; voltage dB → 20 log (same Z).

Memorize 3 / 6 / 10 / 20 dB anchors cold.

Cascade: add dB ; multiply linear ratios.

Attenuator: known power reduction , not a frequency mixer.

Next, RC/RL time constants and impedance networks complete Topic 3-B’s quantitative toolkit.