Study guide

7.7 Regulation, Turns Ratio, Zener Bias & Conductance

FCC General Radiotelephone Operator License GROL

Track your progress as you read

Finished sections get a check mark.

1 Introduction & GROL Exam Overview

1.1 About the General Radiotelephone Operator License 1.2 Exam Format, COLEMs, FRN & Application Process

2 Element 1: Rules & Regulations

2.1 Equipment Requirements (Part 80) 2.2 License Requirements & Operator Authority 2.3 Watchkeeping & Logkeeping Duties 2.4 Log Entries & Required Records 2.5 Ship Station Control, Inspections & International Rules

3 Element 1: Communications Procedures

3.1 Bridge-to-Bridge Operations & VTS 3.2 Distress Communications & Alerting 3.3 Operating Procedures, Calling & Testing 3.4 Urgency (PAN PAN) & Safety (SECURITE) Traffic 3.5 The GMDSS Concept & Ship Responsibilities

4 Element 1: Equipment Operations

4.1 VHF Equipment Controls 4.2 MF/HF SSB Equipment Controls 4.3 DSC Operations & Equipment Faults 4.4 VHF Channel Selection & Channel Assignments 4.5 MF/HF Frequency & Emission Selection 4.6 Required Equipment Tests & On-Air Test Procedure

5 Element 1: Other Equipment & Antennas

5.1 Marine Antennas & Polarization 5.2 EPIRBs & Emergency Beacons 5.3 Power Sources, Reserve Power & Required Tests 5.4 Search and Rescue Transponders (SARTs) 5.5 Survival Craft Portable VHF (SCT) Requirements 5.6 NAVTEX & Maritime Safety Information

6 Element 3: Electrical Principles

6.1 Electrical Elements, Units & Power Types 6.2 Magnetism & Magnetic Circuits 6.3 Resistance, Capacitance & Inductance 6.4 Waveforms & Semiconductor Introduction 6.5 Materials, Corrosion & Skin Effect 6.6 AC Measurement & Conversion Factors 6.7 Conduction, Reactive Power & Maximum Power Transfer

7 Element 3: Electrical Math

7.1 Ohm's Law — Series & Parallel Circuits 7.2 Frequency, Period, Wavelength & Waveform Math 7.3 Power Relationships & Decibels 7.4 RC/RL Time Constants 7.5 Frequency Counter Accuracy, PPM & Harmonics 7.6 Impedance in Rectangular & Polar Coordinates 7.7 Regulation, Turns Ratio, Zener Bias & Conductance

8 Element 3: Circuit Components — Passives & Power Devices

8.1 Capacitors & Photoconductive Devices 8.2 Transformers, Voltage Regulators & Zener Diodes 8.3 Diodes, SCRs & Triacs

9 Element 3: Active Components — Transistors & Devices

9.1 Bipolar Junction Transistors 9.2 FETs, LEDs & Specialty Devices 9.3 Device Selection, Ratings & Thermal Design

10 Element 3: Practical Circuits — RLC, Op Amps & Schematics

10.1 R-L-C Resonant Circuits 10.2 Op Amps, PLLs, VCOs & Mixers 10.3 Reading Schematics & Signal Flow

11 Element 3: Digital Logic

11.1 Logic Gates & Boolean Functions 11.2 Flip-Flops & Sequential Elements 11.3 Multivibrators & Timing Circuits 11.4 Microprocessors & Bus Architecture 11.5 TTL Logic Families & Input Voltage Levels 11.6 Positive & Negative Logic and Truth Tables 11.7 Memory Types & Microprocessor Concepts 11.8 Counters, Prescalers, BCD & Data Converters

12 Element 3: Receivers

12.1 Receiver Theory & Superheterodyne Architecture 12.2 RF Amplifiers & Front-End Design 12.3 Filters & Detectors 12.4 Audio, Squelch & Receiver Performance Specs 12.5 Receiver Oscillators: Colpitts, Hartley & Pierce 12.6 Mixing, Image Frequencies & Spurious Products 12.7 IF Selectivity & Filter Bandwidth

13 Element 3: Transmitters

13.1 RF Amplifier Classes & Efficiency 13.2 Oscillators, Modulators & Tuning Networks 13.3 SSB Transmitters & Modern Transmitter Technology

14 Element 3: Signals, Emissions & Modulation

14.1 Amplitude & Frequency Modulation 14.2 Single-Sideband Modulation 14.3 Pulse Modulation & Emission Types

15 Element 3: Power Sources

15.1 Batteries & Energy Storage 15.2 Motors, Generators & Power Supplies

16 Element 3: Antennas & Feed Lines

16.1 Antenna Theory, Types & Patterns 16.2 Voltage, Current & Impedance on Antennas 16.3 Transmission Lines, Velocity Factor & SWR 16.4 Effective Radiated Power & Antenna Bandwidth

17 Element 3 Background: Propagation & Radio Practice

17.1 Radio Wave Propagation Modes 17.2 Multipath, Fading & Doppler Effects 17.3 Radio Practice, Interference & Good Engineering

18 Element 3: Aircraft Radio Navigation Systems

18.1 DME & VOR 18.2 ILS, ADF & ATC Transponders 18.3 Aircraft Antennas, Frequencies & Equipment Functions

19 Element 3: Installation, Maintenance & Repair

19.1 Indicating Meters & Meter Movements 19.2 Oscilloscopes & Waveform Measurement 19.3 Measurement Procedures 19.4 Installation Codes & Bonding Procedures 19.5 Frequency Standards, SINAD Meters & EMI Hunting 19.6 Spectrum Analyzers, TDRs & Service Monitors 19.7 Bench Repair Practices, ESD & Rework Tools 19.8 Systematic Troubleshooting & Field Fault Diagnosis

20 Element 3: Communications Technology & Marine Systems

20.1 Transmission Types, Coding & Multiplexing 20.2 Signal Processing, Software & Codes 20.3 Marine VHF, MF/HF & SSB-SITOR 20.4 Survival Craft Electronics, FAX & NAVTEX 20.5 NMEA 0183 & NMEA 2000 Data Networks

21 Element 3: RADAR & Satellite Systems

21.1 RADAR Theory & Pulse Fundamentals 21.2 Range, Pulse Width & PRF 21.3 Radar Antennas & Waveguides 21.4 INMARSAT Satellite Communications 21.5 RADAR Components: Magnetron, Duplexer, ATR & Synchro 21.6 RADAR Equipment, ARPA & Radiation Safety 21.7 Low Earth Orbit Systems: Iridium & COSPAS-SARSAT 21.8 GPS Satellite Navigation & DGPS

22 Element 3: RF & Electrical Safety

22.1 RF Radiation Exposure Limits 22.2 Electrical Safety Practices for Radio Technicians

23 Study Strategy & Exam Day

23.1 Study Strategy, Practice Plan & Exam Day

7.7 Regulation, Turns Ratio, Zener Bias & Conductance

Key Takeaways Explain This Topic AI

Percentage voltage regulation is the no-load voltage minus the full-load voltage, divided by the full-load voltage, times 100

A supply with 12 V no load and 10 V full load has 20 percent regulation; a supply with 200 V full load and 25 percent regulation has 250 V no load

Impedance-matching transformer turns ratio is the square root of the impedance ratio - matching 500 ohms to 10 ohms needs 7.1 to 1

Size a Zener current-limiting resistor from the voltage across it divided by the midpoint bias current

Conductance G is the reciprocal of resistance, G equals I divided by V, and is measured in siemens (formerly mhos)

Last updated: August 2026

7.7 Regulation, Turns Ratio, Zener Bias & Conductance

Quick Answer: % regulation = (V_nl − V_fl) / V_fl × 100. Turns ratio = √(Z_source / Z_load) , so 500:10 → 7.1 : 1 . Zener limiting resistor R = (V_in − V_z) / I_midpoint . Conductance G = I / V , unit the siemens (S) , formerly the mho . Series impedance magnitude = √(R² + X²) .

Sub-topic 3-B-018 (Calculations) is the miscellany of the electrical-math topic — five unrelated formulas plus one impedance-magnitude repeat. Each is a single step, so the whole sub-topic is winnable in a few minutes of drill.

Conductance and the siemens

What is the conductance (G) of a circuit if 6 amperes of current flows when 12 volts DC is applied? 0.50 siemens (mhos).

Conductance is simply the reciprocal of resistance :

G = 1 / R = I / V

Here G = 6 A ÷ 12 V = 0.5 S . Equivalently, R = 12/6 = 2 Ω, and 1/2 = 0.5 S. Either route gets there.

  • Quantity Symbol Unit Relationship
  • Resistance R ohm (Ω) R = V / I
  • Conductance G siemens (S) G = I / V = 1 / R
  • Reactance X ohm (Ω)
  • Susceptance B siemens (S) reciprocal of reactance
  • Impedance Z ohm (Ω)
  • Admittance Y siemens (S) reciprocal of impedance

Why two names? The unit was originally the mho — "ohm" spelled backwards, a piece of nineteenth-century engineering humour — and was formally renamed the siemens in 1971 after Werner von Siemens. Both names appear in the pool's own answer text, so recognise either. The mho symbol is an upside-down omega and still appears on older meters and schematics.

When is conductance the more natural quantity? For parallel networks. Resistances in parallel require the reciprocal-of-sum-of-reciprocals dance; conductances in parallel simply add. Three 0.5 S branches in parallel total 1.5 S, which is 0.667 Ω — far quicker than the resistance route. Transistor data sheets use the same idea when they specify transconductance in siemens (section 9.2).

  • Percentage voltage regulation
  • % regulation = (V_no-load − V_full-load) / V_full-load × 100

The denominator is the full-load voltage. That is the detail candidates get wrong, and the pool tests the formula in both directions:

  • Forward: no load 12 V, full load 10 V → (12 − 10)/10 × 100 = 20%
  • Reverse: full load 200 V, regulation 25% → V_nl = 200 × 1.25 = 250 V

Interpret the number properly: lower regulation percentage is better. A perfect supply holds its output constant as load current rises, giving 0%. A 20% figure means the output sags a fifth below its unloaded value when fully loaded — poor for a regulated bench supply, unremarkable for an unregulated transformer-and-rectifier design. Section 15.2 covers the circuits that improve it.

Impedance-matching transformer turns ratio

What turns ratio does a transformer need in order to match a source impedance of 500 ohms to a load of 10 ohms? 7.1 to 1.

The key relationship is that a transformer transforms impedance as the square of the turns ratio:

Z_primary / Z_secondary = (N_p / N_s)² , so N_p / N_s = √(Z_p / Z_s)

Here: 500 / 10 = 50, and √50 = 7.07 ≈ 7.1 : 1 .

The single most common error is answering 50 : 1 — the impedance ratio, not the turns ratio. Take the square root. A quick sanity check: a 4:1 turns ratio gives a 16:1 impedance ratio, not 4:1.

This connects to the maximum power transfer theorem from section 6.7. You match impedances because maximum power reaches the load when load impedance equals source impedance, and a transformer is the classic way to make an unequal pair look equal.

Zener current-limiting resistor

A 1-watt, 10-volt Zener diode with I_min = 5 mA, I_max = 95 mA and Z = 8 Ω is used as part of a voltage regulator in a 20-V supply. Approximately what size current-limiting resistor sets its bias to the midpoint of its operating range? 200 ohms.

Work it in three steps:

  • Midpoint current: (5 mA + 95 mA) / 2 = 50 mA
  • Voltage across the resistor: the supply minus the Zener voltage = 20 − 10 = 10 V
  • Ohm's law: R = 10 V / 0.05 A = 200 Ω

The 8-Ω Zener impedance and the 1-watt rating are deliberately supplied and deliberately unused in this calculation — they are there to check whether you know which parameters the question actually needs. (They matter elsewhere: 1 W ÷ 10 V = 100 mA absolute maximum, consistent with the stated 95 mA I_max.)

Series impedance magnitude

What is the magnitude of the impedance of a series AC circuit having 6 ohms resistance, 17 ohms inductive reactance, and zero capacitive reactance? 18 ohms.

|Z| = √(6² + 17²) = √(36 + 289) = √325 = 18.03 ≈ 18 Ω . This is the same Pythagorean step as section 7.6; note the magnitude is only slightly above the larger of the two terms, which is the usual pattern when one term dominates.

Drill card

  • Ask Formula Pool example
  • Conductance G = I / V 6 A, 12 V → 0.5 S
  • % regulation (V_nl − V_fl)/V_fl × 100 12/10 → 20%
  • No-load from regulation V_nl = V_fl × (1 + reg) 200 V, 25% → 250 V
  • Turns ratio √(Z_p / Z_s) 500:10 → 7.1 : 1
  • Zener resistor (V_in − V_z) / I_mid 10 V / 50 mA → 200 Ω
  • Series |Z| √(R² + X²) 6, 17 → 18 Ω