Study guide

6.7 Conduction, Reactive Power & Maximum Power Transfer

FCC General Radiotelephone Operator License GROL

Track your progress as you read

Finished sections get a check mark.

1 Introduction & GROL Exam Overview

1.1 About the General Radiotelephone Operator License 1.2 Exam Format, COLEMs, FRN & Application Process

2 Element 1: Rules & Regulations

2.1 Equipment Requirements (Part 80) 2.2 License Requirements & Operator Authority 2.3 Watchkeeping & Logkeeping Duties 2.4 Log Entries & Required Records 2.5 Ship Station Control, Inspections & International Rules

3 Element 1: Communications Procedures

3.1 Bridge-to-Bridge Operations & VTS 3.2 Distress Communications & Alerting 3.3 Operating Procedures, Calling & Testing 3.4 Urgency (PAN PAN) & Safety (SECURITE) Traffic 3.5 The GMDSS Concept & Ship Responsibilities

4 Element 1: Equipment Operations

4.1 VHF Equipment Controls 4.2 MF/HF SSB Equipment Controls 4.3 DSC Operations & Equipment Faults 4.4 VHF Channel Selection & Channel Assignments 4.5 MF/HF Frequency & Emission Selection 4.6 Required Equipment Tests & On-Air Test Procedure

5 Element 1: Other Equipment & Antennas

5.1 Marine Antennas & Polarization 5.2 EPIRBs & Emergency Beacons 5.3 Power Sources, Reserve Power & Required Tests 5.4 Search and Rescue Transponders (SARTs) 5.5 Survival Craft Portable VHF (SCT) Requirements 5.6 NAVTEX & Maritime Safety Information

6 Element 3: Electrical Principles

6.1 Electrical Elements, Units & Power Types 6.2 Magnetism & Magnetic Circuits 6.3 Resistance, Capacitance & Inductance 6.4 Waveforms & Semiconductor Introduction 6.5 Materials, Corrosion & Skin Effect 6.6 AC Measurement & Conversion Factors 6.7 Conduction, Reactive Power & Maximum Power Transfer

7 Element 3: Electrical Math

7.1 Ohm's Law — Series & Parallel Circuits 7.2 Frequency, Period, Wavelength & Waveform Math 7.3 Power Relationships & Decibels 7.4 RC/RL Time Constants 7.5 Frequency Counter Accuracy, PPM & Harmonics 7.6 Impedance in Rectangular & Polar Coordinates 7.7 Regulation, Turns Ratio, Zener Bias & Conductance

8 Element 3: Circuit Components — Passives & Power Devices

8.1 Capacitors & Photoconductive Devices 8.2 Transformers, Voltage Regulators & Zener Diodes 8.3 Diodes, SCRs & Triacs

9 Element 3: Active Components — Transistors & Devices

9.1 Bipolar Junction Transistors 9.2 FETs, LEDs & Specialty Devices 9.3 Device Selection, Ratings & Thermal Design

10 Element 3: Practical Circuits — RLC, Op Amps & Schematics

10.1 R-L-C Resonant Circuits 10.2 Op Amps, PLLs, VCOs & Mixers 10.3 Reading Schematics & Signal Flow

11 Element 3: Digital Logic

11.1 Logic Gates & Boolean Functions 11.2 Flip-Flops & Sequential Elements 11.3 Multivibrators & Timing Circuits 11.4 Microprocessors & Bus Architecture 11.5 TTL Logic Families & Input Voltage Levels 11.6 Positive & Negative Logic and Truth Tables 11.7 Memory Types & Microprocessor Concepts 11.8 Counters, Prescalers, BCD & Data Converters

12 Element 3: Receivers

12.1 Receiver Theory & Superheterodyne Architecture 12.2 RF Amplifiers & Front-End Design 12.3 Filters & Detectors 12.4 Audio, Squelch & Receiver Performance Specs 12.5 Receiver Oscillators: Colpitts, Hartley & Pierce 12.6 Mixing, Image Frequencies & Spurious Products 12.7 IF Selectivity & Filter Bandwidth

13 Element 3: Transmitters

13.1 RF Amplifier Classes & Efficiency 13.2 Oscillators, Modulators & Tuning Networks 13.3 SSB Transmitters & Modern Transmitter Technology

14 Element 3: Signals, Emissions & Modulation

14.1 Amplitude & Frequency Modulation 14.2 Single-Sideband Modulation 14.3 Pulse Modulation & Emission Types

15 Element 3: Power Sources

15.1 Batteries & Energy Storage 15.2 Motors, Generators & Power Supplies

16 Element 3: Antennas & Feed Lines

16.1 Antenna Theory, Types & Patterns 16.2 Voltage, Current & Impedance on Antennas 16.3 Transmission Lines, Velocity Factor & SWR 16.4 Effective Radiated Power & Antenna Bandwidth

17 Element 3 Background: Propagation & Radio Practice

17.1 Radio Wave Propagation Modes 17.2 Multipath, Fading & Doppler Effects 17.3 Radio Practice, Interference & Good Engineering

18 Element 3: Aircraft Radio Navigation Systems

18.1 DME & VOR 18.2 ILS, ADF & ATC Transponders 18.3 Aircraft Antennas, Frequencies & Equipment Functions

19 Element 3: Installation, Maintenance & Repair

19.1 Indicating Meters & Meter Movements 19.2 Oscilloscopes & Waveform Measurement 19.3 Measurement Procedures 19.4 Installation Codes & Bonding Procedures 19.5 Frequency Standards, SINAD Meters & EMI Hunting 19.6 Spectrum Analyzers, TDRs & Service Monitors 19.7 Bench Repair Practices, ESD & Rework Tools 19.8 Systematic Troubleshooting & Field Fault Diagnosis

20 Element 3: Communications Technology & Marine Systems

20.1 Transmission Types, Coding & Multiplexing 20.2 Signal Processing, Software & Codes 20.3 Marine VHF, MF/HF & SSB-SITOR 20.4 Survival Craft Electronics, FAX & NAVTEX 20.5 NMEA 0183 & NMEA 2000 Data Networks

21 Element 3: RADAR & Satellite Systems

21.1 RADAR Theory & Pulse Fundamentals 21.2 Range, Pulse Width & PRF 21.3 Radar Antennas & Waveguides 21.4 INMARSAT Satellite Communications 21.5 RADAR Components: Magnetron, Duplexer, ATR & Synchro 21.6 RADAR Equipment, ARPA & Radiation Safety 21.7 Low Earth Orbit Systems: Iridium & COSPAS-SARSAT 21.8 GPS Satellite Navigation & DGPS

22 Element 3: RF & Electrical Safety

22.1 RF Radiation Exposure Limits 22.2 Electrical Safety Practices for Radio Technicians

23 Study Strategy & Exam Day

23.1 Study Strategy, Practice Plan & Exam Day

6.7 Conduction, Reactive Power & Maximum Power Transfer

Key Takeaways Explain This Topic AI

Halving the cross-sectional area of a conductor doubles its resistance

Descending conductivity order is silver, copper, aluminium, iron, lead

Reactive power in a circuit containing both inductance and capacitance alternates between magnetic and electric fields and is never dissipated

True power in an out-of-phase AC circuit is apparent power multiplied by the power factor

  • Maximum power is transferred to the load when the load impedance equals the internal impedance of the source
  • Last updated: August 2026

6.7 Conduction, Reactive Power & Maximum Power Transfer

Quick Answer: Halving cross-sectional area doubles resistance. Descending conductivity: silver, copper, aluminium, iron, lead . Reactive power shuttles between magnetic and electric fields and is not dissipated . True power = apparent power × power factor. Maximum power transfer happens when load impedance = source internal impedance .

Sub-topic 3-A-008 (Conduction) is broader than its title suggests. It bundles conductor geometry, the conductivity league table, the nature of reactive power, and the maximum power transfer theorem—four ideas that reappear throughout Element 3.

Conductor geometry and resistance

Halving the cross-sectional area of a conductor will double the resistance.

Resistance follows R = ρL / A, where ρ is resistivity, L is length, and A is cross-sectional area:

  • Change Effect on resistance
  • Halve the area Doubles — the pool's answer
  • Double the area Halves
  • Double the length Doubles
  • Halve the length Halves
  • Use a material of higher resistivity Increases proportionally

Area appears in the denominator , so resistance is inversely proportional to it—that is the whole trick. Note also that wire gauge numbering runs backwards: a larger AWG number means a thinner wire and therefore more resistance per foot. Going from AWG 14 to AWG 17 roughly halves the area and roughly doubles the resistance.

Recall from section 6.5 that at RF the skin effect confines current to the surface, so the DC cross-sectional area stops telling the whole story—an important caveat when you are sizing an RF ground strap rather than a DC feed.

The conductivity league table

Which group is correct for listing common materials in order of descending conductivity? Silver, copper, aluminium, iron, and lead.

  • Rank Metal Practical note
  • 1 Silver Best conductor; used as plating where surface conduction matters (waveguide, UHF contacts)
  • 2 Copper ~95% of silver's conductivity at a fraction of the cost — the default for wiring
  • 3 Aluminium ~60% of copper, but far lighter; used in aircraft wiring and large feeders
  • 4 Iron Poor conductor; magnetic, so also unsuitable for many RF roles
  • 5 Lead Worst of the five; used for shielding mass, not conduction

Only the ordering matters for the exam. If an option opens with copper before silver, or places aluminium above copper, it is wrong.

Reactive power: energy that never leaves

What happens to reactive power in a circuit that has both inductors and capacitors? It alternates between magnetic and electric fields and is not dissipated.

This is the conceptual heart of AC power and worth getting genuinely right rather than memorising.

An inductor stores energy in a magnetic field while current rises, then returns it to the circuit as current falls.

A capacitor stores energy in an electric field while voltage rises, then returns it as voltage falls.

Because their storage phases are opposite, in a circuit containing both, energy sloshes back and forth between the two fields .

None of that energy is converted to heat. Only resistance dissipates power. That is why an ideal inductor or capacitor consumes no real power no matter how large the circulating current—and also why a badly power-factor-corrected installation can circulate large currents (with real I²R losses in the wiring ) while delivering little useful work.

True, apparent, and reactive power

  • Quantity Symbol / unit Meaning
  • Apparent power VA (volt-amperes) Simply V × I, ignoring phase
  • True (real) power W (watts) The power actually dissipated
  • Reactive power VAR The circulating, non-dissipated component
  • Power factor (dimensionless) cos θ, where θ is the phase angle between V and I

How do you compute true power in a circuit where AC voltage and current are out of phase? Multiply apparent power times the power factor.

That relationship is asked in two sub-topics — here and in 3-B-013 — so it is worth two marks. The companion numbers from the electrical-math topic:

  • Phase angle Power factor (cos θ)
  • 0° 1.0 (purely resistive)
  • 30° 0.866
  • 45° 0.707
  • 60° 0.5
  • 90° 0 (purely reactive — no true power at all)

Those three middle values are asked directly. Note the pattern: cos 60° = 0.5 , not 0.866. Candidates who memorise sines instead of cosines reverse 30° and 60°.

Maximum power transfer

Assuming a power source to have a fixed value of internal resistance, maximum power will be transferred to the load when the load impedance equals the internal impedance of the source.

The reasoning is a balance. If the load impedance is much lower than the source impedance, current is high but most of the voltage drops inside the source. If the load is much higher , the voltage divides favourably but almost no current flows. The product V × I in the load peaks exactly at the match point .

Two cautions that matter professionally:

Maximum power transfer is not maximum efficiency. At a perfect match, half the total power is dissipated inside the source , so efficiency is 50%. Power distribution systems deliberately run a very low source impedance into a much higher load for efficiency; RF systems match because getting the signal out matters more than heat in the final.

This theorem is why RF systems are built around a consistent characteristic impedance —50 ohms for most commercial radio work. Matching transmitter, feed line, and antenna is the practical application, and it drives the transformer turns-ratio and SWR material in sections 7.6 and 16.3.