Study guide

6.1 Electrical Elements, Units & Power Types

FCC General Radiotelephone Operator License GROL

Track your progress as you read

Finished sections get a check mark.

1 Introduction & GROL Exam Overview

1.1 About the General Radiotelephone Operator License 1.2 Exam Format, COLEMs, FRN & Application Process

2 Element 1: Rules & Regulations

2.1 Equipment Requirements (Part 80) 2.2 License Requirements & Operator Authority 2.3 Watchkeeping & Logkeeping Duties 2.4 Log Entries & Required Records 2.5 Ship Station Control, Inspections & International Rules

3 Element 1: Communications Procedures

3.1 Bridge-to-Bridge Operations & VTS 3.2 Distress Communications & Alerting 3.3 Operating Procedures, Calling & Testing 3.4 Urgency (PAN PAN) & Safety (SECURITE) Traffic 3.5 The GMDSS Concept & Ship Responsibilities

4 Element 1: Equipment Operations

4.1 VHF Equipment Controls 4.2 MF/HF SSB Equipment Controls 4.3 DSC Operations & Equipment Faults 4.4 VHF Channel Selection & Channel Assignments 4.5 MF/HF Frequency & Emission Selection 4.6 Required Equipment Tests & On-Air Test Procedure

5 Element 1: Other Equipment & Antennas

5.1 Marine Antennas & Polarization 5.2 EPIRBs & Emergency Beacons 5.3 Power Sources, Reserve Power & Required Tests 5.4 Search and Rescue Transponders (SARTs) 5.5 Survival Craft Portable VHF (SCT) Requirements 5.6 NAVTEX & Maritime Safety Information

6 Element 3: Electrical Principles

6.1 Electrical Elements, Units & Power Types 6.2 Magnetism & Magnetic Circuits 6.3 Resistance, Capacitance & Inductance 6.4 Waveforms & Semiconductor Introduction 6.5 Materials, Corrosion & Skin Effect 6.6 AC Measurement & Conversion Factors 6.7 Conduction, Reactive Power & Maximum Power Transfer

7 Element 3: Electrical Math

7.1 Ohm's Law — Series & Parallel Circuits 7.2 Frequency, Period, Wavelength & Waveform Math 7.3 Power Relationships & Decibels 7.4 RC/RL Time Constants 7.5 Frequency Counter Accuracy, PPM & Harmonics 7.6 Impedance in Rectangular & Polar Coordinates 7.7 Regulation, Turns Ratio, Zener Bias & Conductance

8 Element 3: Circuit Components — Passives & Power Devices

8.1 Capacitors & Photoconductive Devices 8.2 Transformers, Voltage Regulators & Zener Diodes 8.3 Diodes, SCRs & Triacs

9 Element 3: Active Components — Transistors & Devices

9.1 Bipolar Junction Transistors 9.2 FETs, LEDs & Specialty Devices 9.3 Device Selection, Ratings & Thermal Design

10 Element 3: Practical Circuits — RLC, Op Amps & Schematics

10.1 R-L-C Resonant Circuits 10.2 Op Amps, PLLs, VCOs & Mixers 10.3 Reading Schematics & Signal Flow

11 Element 3: Digital Logic

11.1 Logic Gates & Boolean Functions 11.2 Flip-Flops & Sequential Elements 11.3 Multivibrators & Timing Circuits 11.4 Microprocessors & Bus Architecture 11.5 TTL Logic Families & Input Voltage Levels 11.6 Positive & Negative Logic and Truth Tables 11.7 Memory Types & Microprocessor Concepts 11.8 Counters, Prescalers, BCD & Data Converters

12 Element 3: Receivers

12.1 Receiver Theory & Superheterodyne Architecture 12.2 RF Amplifiers & Front-End Design 12.3 Filters & Detectors 12.4 Audio, Squelch & Receiver Performance Specs 12.5 Receiver Oscillators: Colpitts, Hartley & Pierce 12.6 Mixing, Image Frequencies & Spurious Products 12.7 IF Selectivity & Filter Bandwidth

13 Element 3: Transmitters

13.1 RF Amplifier Classes & Efficiency 13.2 Oscillators, Modulators & Tuning Networks 13.3 SSB Transmitters & Modern Transmitter Technology

14 Element 3: Signals, Emissions & Modulation

14.1 Amplitude & Frequency Modulation 14.2 Single-Sideband Modulation 14.3 Pulse Modulation & Emission Types

15 Element 3: Power Sources

15.1 Batteries & Energy Storage 15.2 Motors, Generators & Power Supplies

16 Element 3: Antennas & Feed Lines

16.1 Antenna Theory, Types & Patterns 16.2 Voltage, Current & Impedance on Antennas 16.3 Transmission Lines, Velocity Factor & SWR 16.4 Effective Radiated Power & Antenna Bandwidth

17 Element 3 Background: Propagation & Radio Practice

17.1 Radio Wave Propagation Modes 17.2 Multipath, Fading & Doppler Effects 17.3 Radio Practice, Interference & Good Engineering

18 Element 3: Aircraft Radio Navigation Systems

18.1 DME & VOR 18.2 ILS, ADF & ATC Transponders 18.3 Aircraft Antennas, Frequencies & Equipment Functions

19 Element 3: Installation, Maintenance & Repair

19.1 Indicating Meters & Meter Movements 19.2 Oscilloscopes & Waveform Measurement 19.3 Measurement Procedures 19.4 Installation Codes & Bonding Procedures 19.5 Frequency Standards, SINAD Meters & EMI Hunting 19.6 Spectrum Analyzers, TDRs & Service Monitors 19.7 Bench Repair Practices, ESD & Rework Tools 19.8 Systematic Troubleshooting & Field Fault Diagnosis

20 Element 3: Communications Technology & Marine Systems

20.1 Transmission Types, Coding & Multiplexing 20.2 Signal Processing, Software & Codes 20.3 Marine VHF, MF/HF & SSB-SITOR 20.4 Survival Craft Electronics, FAX & NAVTEX 20.5 NMEA 0183 & NMEA 2000 Data Networks

21 Element 3: RADAR & Satellite Systems

21.1 RADAR Theory & Pulse Fundamentals 21.2 Range, Pulse Width & PRF 21.3 Radar Antennas & Waveguides 21.4 INMARSAT Satellite Communications 21.5 RADAR Components: Magnetron, Duplexer, ATR & Synchro 21.6 RADAR Equipment, ARPA & Radiation Safety 21.7 Low Earth Orbit Systems: Iridium & COSPAS-SARSAT 21.8 GPS Satellite Navigation & DGPS

22 Element 3: RF & Electrical Safety

22.1 RF Radiation Exposure Limits 22.2 Electrical Safety Practices for Radio Technicians

23 Study Strategy & Exam Day

23.1 Study Strategy, Practice Plan & Exam Day

6.1 Electrical Elements, Units & Power Types

Key Takeaways Explain This Topic AI

The product of simultaneous AC voltmeter and AC ammeter readings is apparent power, expressed in volt-amperes (VA), not true watts

The watt is the basic unit of electrical power; energy stored in an electrostatic field is expressed in joules, and a capacitor is the device that stores that energy

Reactive power is the out-of-phase power associated with inductors and capacitors; it is not dissipated as heat the way true power is

True power equals apparent power times the power factor; P = V × I relationships must be interpreted carefully on AC circuits with phase shift

  • Maximum power is transferred to a load when the load impedance equals the internal impedance of the source
  • Last updated: August 2026

6.1 Electrical Elements, Units & Power Types

Quick Answer: Multiply an AC voltmeter reading by an AC ammeter reading and you get apparent power (VA). The basic unit of electrical power is the watt . Energy stored in an electrostatic field is measured in joules , and a capacitor is the device that stores it. Reactive power is the out-of-phase L/C power; true power is what resistors actually dissipate. On AC, true power = apparent power × power factor.

Element 3 begins with electrical principles because every later topic—components, circuits, transmitters, antennas—assumes you can name units, separate power types, and avoid treating every V×I product as “watts on the workbench.” Topic 3-A (key topics 001–008 ) is the foundation under all of general radiotelephone theory.

Core SI units GROL techs must own

  • Quantity Unit Symbol What it measures
  • Voltage (EMF, potential) volt V Electrical pressure that can drive charge
  • Current ampere A Rate of charge flow
  • Resistance / impedance ohm Ω Opposition to current
  • Power watt W Rate of energy transfer or dissipation
  • Energy joule J Stored or delivered work capability
  • Capacitance farad F Ability to store charge / electrostatic energy
  • Inductance henry H Ability to store energy in a magnetic field
  • Frequency hertz Hz Cycles per second
  • Apparent power volt-ampere VA Product of RMS voltage and RMS current
  • Reactive power volt-ampere reactive VAR Out-of-phase power associated with L and C

Exam hook — basic unit of electrical power: the watt . Not the ohm (resistance), not the volt (potential), not the ampere (current). Power is the rate of doing electrical work; energy is the amount of work stored or delivered over time.

Exam hook — electrostatic energy: the amount of electrical energy stored in an electrostatic field is expressed in joules . The device that stores electrical energy in an electrostatic field is a capacitor (not a battery, transformer, or inductor). Batteries store chemical energy; inductors store energy in a magnetic field; transformers couple magnetic fields between windings but are not the classic “electrostatic store” answer.

Apparent power: voltmeter × ammeter

What is the product of the readings of an AC voltmeter and an AC ammeter called? Apparent power.

If a voltmeter across an AC circuit reads 120 V and an ammeter in series reads 2 A, then: S = V × I = 120 V × 2 A = 240 V A S = V \times I = 120\,\mathrm{V} \times 2\,\mathrm{A} = 240\,\mathrm{VA} S = V × I = 120 V × 2 A = 240 VA

That product is apparent power (often written S or | S |). It is not automatically true power, because on AC the voltage and current may not be in phase. Meters that display RMS voltage and RMS current give you the magnitudes; they do not by themselves tell you the phase angle between v and i .

  • Name How you get it Unit Physical meaning
  • Apparent power AC V × AC I (RMS) VA Total “size” of the VA product the source must support

True (real) power Apparent × power factor, or I ² R heating W Power actually converted to heat, light, RF radiation, mechanical work

Reactive power Out-of-phase L/C component VAR Power that oscillates between source and energy-storage fields

Memory hook: VA is what the meters multiply; watts is what the resistor burns; VAR is what L and C bounce.

True power vs reactive power

Reactive power is the exam term for the out-of-phase power associated with inductors and capacitors . In a pure inductance or pure capacitance (ideal case), voltage and current are 90° apart. Instantaneous power still exists, but over a full cycle the average energy delivered to the ideal L or C is zero—the energy is stored and returned.

Pool-level fact you will reuse in later math topics: in a circuit with both inductors and capacitors, reactive power alternates between magnetic and electric fields and is not dissipated . It is not “burned up as heat in the reactive fields.” Heat is a true-power story (resistance, losses, radiation loads).

How do you compute true power when AC voltage and current are out of phase? P t r u e = S × P F = V R M S I R M S cos ⁡ ϕ P_{\mathrm{true}} = S \times \mathrm{PF} = V_{\mathrm{RMS}} \, I_{\mathrm{RMS}} \, \cos\phi P true ​ = S × PF = V RMS ​ I RMS ​ cos ϕ

In words: multiply apparent power by the power factor . Power factor is the cosine of the phase angle between voltage and current (for sinusoidal steady state). Multiplying RMS V by RMS I alone gives apparent power, not true power, when phase shift is present. Dividing or subtracting “power factor from apparent power” is not the rule.

Worked example — three power numbers from one circuit

A marine SSB PA supply rail is measured at 24.0 V RMS into a load that draws 5.0 A RMS . An instrument (or calculation) shows power factor 0.80 lagging because of inductive filtering and cabling.

  • Apparent power: S = 24 × 5 = 120 V A S = 24 \times 5 = 120\,\mathrm{VA} S = 24 × 5 = 120 VA
  • True power: P = 120 × 0.80 = 96 W P = 120 \times 0.80 = 96\,\mathrm{W} P = 120 × 0.80 = 96 W

Reactive power (magnitude): using Q = S 2 − P 2 Q = \sqrt{S^2 - P^2} Q = S 2 − P 2 ​ gives Q = 120 2 − 96 2 = 72 V A R Q = \sqrt{120^2 - 96^2} = 72\,\mathrm{VAR} Q = 12 0 2 − 9 6 2 ​ = 72 VAR

If you only memorize “power is V times I,” you would report 120 W and miss that only 96 W is true power. Element 3 rewards the distinction.

P = VI relationships without the traps

On DC (or purely resistive AC), true power collapses to the simple product: P = V I = I 2 R = V 2 R P = VI = I^2 R = \frac{V^2}{R} P = V I = I 2 R = R V 2 ​

On AC with reactance , keep these rules of thumb:

V_RMS × I_RMS → apparent power (VA), always a valid magnitude product for sinusoids when both meters read RMS.

True power requires resistance or power factor: P = I 2 R P = I^2 R P = I 2 R in the resistive elements, or P = S × P F P = S \times \mathrm{PF} P = S × PF .

Inductive reactance formula (preview of §6.3, already in 3-A-001): X L = 2 π f L X_L = 2\pi f L X L ​ = 2 π f L . Reactance is not resistance, but it still limits AC current and creates the phase shift that produces reactive power.

Do not call reactive power “peak envelope power.” PEP is an RF envelope concept used later for transmitters; reactive power is the L/C out-of-phase power.

Maximum power transfer

Assuming a source with fixed internal resistance (or fixed internal impedance), maximum power is transferred to the load when the load impedance equals the internal impedance of the source . That is the classic conjugate-match idea stated at Element 3 level: match the load to the source, do not deliberately run the load “much higher” or “much lower” if the goal is maximum delivered power.

In RF work you will revisit this as antenna and transmission-line matching. At Topic 3-A, remember the pure statement: load Z = source internal Z for maximum power transfer.

Putting §6.1 together for exam day

When a stem mentions meters, watts, joules, capacitors, reactive power, or power factor, run this checklist:

V_AC × I_AC → apparent power (VA).

Basic power unit → watt .

Electrostatic stored energy unit → joule ; device → capacitor .

Out-of-phase L/C power → reactive power (not dissipated like true power).

True power with phase shift → apparent × power factor .

Max power transfer → load impedance matches source internal impedance.

Master these six hooks and you clear the electrical-elements slice of Topic 3-A before moving into magnetism, materials, RLC properties, waveforms, and semiconductors.