Study guide

6.3 Resistance, Capacitance & Inductance

FCC General Radiotelephone Operator License GROL

Track your progress as you read

Finished sections get a check mark.

1 Introduction & GROL Exam Overview

1.1 About the General Radiotelephone Operator License 1.2 Exam Format, COLEMs, FRN & Application Process

2 Element 1: Rules & Regulations

2.1 Equipment Requirements (Part 80) 2.2 License Requirements & Operator Authority 2.3 Watchkeeping & Logkeeping Duties 2.4 Log Entries & Required Records 2.5 Ship Station Control, Inspections & International Rules

3 Element 1: Communications Procedures

3.1 Bridge-to-Bridge Operations & VTS 3.2 Distress Communications & Alerting 3.3 Operating Procedures, Calling & Testing 3.4 Urgency (PAN PAN) & Safety (SECURITE) Traffic 3.5 The GMDSS Concept & Ship Responsibilities

4 Element 1: Equipment Operations

4.1 VHF Equipment Controls 4.2 MF/HF SSB Equipment Controls 4.3 DSC Operations & Equipment Faults 4.4 VHF Channel Selection & Channel Assignments 4.5 MF/HF Frequency & Emission Selection 4.6 Required Equipment Tests & On-Air Test Procedure

5 Element 1: Other Equipment & Antennas

5.1 Marine Antennas & Polarization 5.2 EPIRBs & Emergency Beacons 5.3 Power Sources, Reserve Power & Required Tests 5.4 Search and Rescue Transponders (SARTs) 5.5 Survival Craft Portable VHF (SCT) Requirements 5.6 NAVTEX & Maritime Safety Information

6 Element 3: Electrical Principles

6.1 Electrical Elements, Units & Power Types 6.2 Magnetism & Magnetic Circuits 6.3 Resistance, Capacitance & Inductance 6.4 Waveforms & Semiconductor Introduction 6.5 Materials, Corrosion & Skin Effect 6.6 AC Measurement & Conversion Factors 6.7 Conduction, Reactive Power & Maximum Power Transfer

7 Element 3: Electrical Math

7.1 Ohm's Law — Series & Parallel Circuits 7.2 Frequency, Period, Wavelength & Waveform Math 7.3 Power Relationships & Decibels 7.4 RC/RL Time Constants 7.5 Frequency Counter Accuracy, PPM & Harmonics 7.6 Impedance in Rectangular & Polar Coordinates 7.7 Regulation, Turns Ratio, Zener Bias & Conductance

8 Element 3: Circuit Components — Passives & Power Devices

8.1 Capacitors & Photoconductive Devices 8.2 Transformers, Voltage Regulators & Zener Diodes 8.3 Diodes, SCRs & Triacs

9 Element 3: Active Components — Transistors & Devices

9.1 Bipolar Junction Transistors 9.2 FETs, LEDs & Specialty Devices 9.3 Device Selection, Ratings & Thermal Design

10 Element 3: Practical Circuits — RLC, Op Amps & Schematics

10.1 R-L-C Resonant Circuits 10.2 Op Amps, PLLs, VCOs & Mixers 10.3 Reading Schematics & Signal Flow

11 Element 3: Digital Logic

11.1 Logic Gates & Boolean Functions 11.2 Flip-Flops & Sequential Elements 11.3 Multivibrators & Timing Circuits 11.4 Microprocessors & Bus Architecture 11.5 TTL Logic Families & Input Voltage Levels 11.6 Positive & Negative Logic and Truth Tables 11.7 Memory Types & Microprocessor Concepts 11.8 Counters, Prescalers, BCD & Data Converters

12 Element 3: Receivers

12.1 Receiver Theory & Superheterodyne Architecture 12.2 RF Amplifiers & Front-End Design 12.3 Filters & Detectors 12.4 Audio, Squelch & Receiver Performance Specs 12.5 Receiver Oscillators: Colpitts, Hartley & Pierce 12.6 Mixing, Image Frequencies & Spurious Products 12.7 IF Selectivity & Filter Bandwidth

13 Element 3: Transmitters

13.1 RF Amplifier Classes & Efficiency 13.2 Oscillators, Modulators & Tuning Networks 13.3 SSB Transmitters & Modern Transmitter Technology

14 Element 3: Signals, Emissions & Modulation

14.1 Amplitude & Frequency Modulation 14.2 Single-Sideband Modulation 14.3 Pulse Modulation & Emission Types

15 Element 3: Power Sources

15.1 Batteries & Energy Storage 15.2 Motors, Generators & Power Supplies

16 Element 3: Antennas & Feed Lines

16.1 Antenna Theory, Types & Patterns 16.2 Voltage, Current & Impedance on Antennas 16.3 Transmission Lines, Velocity Factor & SWR 16.4 Effective Radiated Power & Antenna Bandwidth

17 Element 3 Background: Propagation & Radio Practice

17.1 Radio Wave Propagation Modes 17.2 Multipath, Fading & Doppler Effects 17.3 Radio Practice, Interference & Good Engineering

18 Element 3: Aircraft Radio Navigation Systems

18.1 DME & VOR 18.2 ILS, ADF & ATC Transponders 18.3 Aircraft Antennas, Frequencies & Equipment Functions

19 Element 3: Installation, Maintenance & Repair

19.1 Indicating Meters & Meter Movements 19.2 Oscilloscopes & Waveform Measurement 19.3 Measurement Procedures 19.4 Installation Codes & Bonding Procedures 19.5 Frequency Standards, SINAD Meters & EMI Hunting 19.6 Spectrum Analyzers, TDRs & Service Monitors 19.7 Bench Repair Practices, ESD & Rework Tools 19.8 Systematic Troubleshooting & Field Fault Diagnosis

20 Element 3: Communications Technology & Marine Systems

20.1 Transmission Types, Coding & Multiplexing 20.2 Signal Processing, Software & Codes 20.3 Marine VHF, MF/HF & SSB-SITOR 20.4 Survival Craft Electronics, FAX & NAVTEX 20.5 NMEA 0183 & NMEA 2000 Data Networks

21 Element 3: RADAR & Satellite Systems

21.1 RADAR Theory & Pulse Fundamentals 21.2 Range, Pulse Width & PRF 21.3 Radar Antennas & Waveguides 21.4 INMARSAT Satellite Communications 21.5 RADAR Components: Magnetron, Duplexer, ATR & Synchro 21.6 RADAR Equipment, ARPA & Radiation Safety 21.7 Low Earth Orbit Systems: Iridium & COSPAS-SARSAT 21.8 GPS Satellite Navigation & DGPS

22 Element 3: RF & Electrical Safety

22.1 RF Radiation Exposure Limits 22.2 Electrical Safety Practices for Radio Technicians

23 Study Strategy & Exam Day

23.1 Study Strategy, Practice Plan & Exam Day

6.3 Resistance, Capacitance & Inductance

Key Takeaways Explain This Topic AI

Resistance is measured in ohms; capacitance in farads; inductance in henrys—three passive properties that dominate RF network behavior

Inductive reactance is XL = 2πfL; capacitive reactance is XC = 1/(2πfC); both are frequency-dependent oppositions measured in ohms but are not resistance

Series resistances and series inductances add; parallel capacitances add; parallel resistances and series capacitances use reciprocal (product-over-sum) style combinations

Inductors store energy in a magnetic field; capacitors store energy in an electric (electrostatic) field

  • Bypass capacitors provide a low-impedance path to ground for AC; reducing coil turns reduces inductance
  • Last updated: August 2026

6.3 Resistance, Capacitance & Inductance

Quick Answer: R in ohms , C in farads , L in henrys . X L = 2 π f L X_L = 2\pi f L X L ​ = 2 π f L , X C = 1 / ( 2 π f C ) X_C = 1/(2\pi f C) X C ​ = 1/ ( 2 π f C ) . Series L values add ; parallel C values add . Inductors store magnetic energy; capacitors store electric energy. A bypass capacitor shunts AC to ground through a low impedance; fewer turns means less inductance .

If §6.1 named power and §6.2 named materials, this section quantifies the three passive properties you adjust every time you tune a tank, set a coupling network, or troubleshoot an RF deck.

Units and physical meaning

  • Property Unit Symbol Stores energy in… DC steady-state ideal behavior
  • Resistance ohm (Ω) R None (dissipates as heat) Passes current per Ohm’s law; drops voltage
  • Capacitance farad (F) C Electric / electrostatic field Open circuit (after charged); blocks DC
  • Inductance henry (H) L Magnetic field Short circuit (after current established); passes DC

Practical values: RF caps are often pF–µF; inductors µH–mH; resistors from fractions of an ohm to megaohms. The farad and henry are large base units—prefixes dominate lab talk—but the exam still wants the base unit names.

Resistance opposes current and dissipates true power as heat: P = I 2 R P = I^2 R P = I 2 R . It does not return energy to the circuit each cycle the way pure L and C do.

Reactance: frequency-dependent opposition

Reactance is measured in ohms but is not resistance. It causes phase shift and contributes to impedance (Z = R + jX) without the continuous heat of a pure resistor (ideal case).

Inductive reactance X L = 2 π f L X_L = 2\pi f L X L ​ = 2 π f L

(f) in hertz, (L) in henrys → X L X_L X L ​ in ohms.

Double frequency or double L → double X L X_L X L ​ .

Coils look more open at higher RF frequencies (until self-resonance and parasitics intervene).

This is the exact formula tested in Topic 3-A: if frequency and coil inductance are known, X L = 2 π f L X_L = 2\pi f L X L ​ = 2 π f L (not π f L \pi f L π f L , not the capacitive formula).

Capacitive reactance X C = 1 2 π f C X_C = \frac{1}{2\pi f C} X C ​ = 2 π f C 1 ​

Higher frequency or larger C → smaller X C X_C X C ​ .

Capacitors look more like shorts to high-frequency AC and opens to DC—foundation of coupling and bypass practice.

  • Device Reactance vs frequency Phase (ideal)
  • Inductor X L X_L X L ​ rises with (f) Current lags voltage by 90°
  • Capacitor X C X_C X C ​ falls with (f) Current leads voltage by 90°
  • Resistor R independent of (f) (ideal) V and I in phase
  • Worked example — coil reactance

An antenna loading coil is 50 µH at 2.0 MHz (near the 160 m / marine MF neighborhood for scale). X L = 2 π ( 2.0 × 10 6 ) ( 50 × 10 − 6 ) ≈ 628 Ω X_L = 2\pi (2.0\times 10^6)(50\times 10^{-6}) \approx 628\,\Omega X L ​ = 2 π ( 2.0 × 1 0 6 ) ( 50 × 1 0 − 6 ) ≈ 628 Ω

At 4.0 MHz , the same coil presents about 1.26 kΩ of X L X_L X L ​ . Frequency doubled → reactance doubled. That is why a coil that “looks modest” at low HF can dominate impedance higher up.

Worked example — capacitor reactance

A 0.01 µF bypass at 1 MHz : X C = 1 2 π ( 1 × 10 6 ) ( 0.01 × 10 − 6 ) ≈ 16 Ω X_C = \frac{1}{2\pi (1\times 10^6)(0.01\times 10^{-6})} \approx 16\,\Omega X C ​ = 2 π ( 1 × 1 0 6 ) ( 0.01 × 1 0 − 6 ) 1 ​ ≈ 16 Ω

At audio (say 1 kHz) the same capacitor is roughly 16 kΩ —poor as a bypass, fine as a coupling thought experiment. Frequency agility of X C X_C X C ​ is the whole point of choosing bypass values.

  • Series and parallel combination formulas
  • Resistance

Series: R T = R 1 + R 2 + R 3 + ⋯ R_T = R_1 + R_2 + R_3 + \cdots R T ​ = R 1 ​ + R 2 ​ + R 3 ​ + ⋯ (always larger than any single resistor).

Parallel: 1 R T = 1 R 1 + 1 R 2 + ⋯ \frac{1}{R_T} = \frac{1}{R_1} + \frac{1}{R_2} + \cdots R T ​ 1 ​ = R 1 ​ 1 ​ + R 2 ​ 1 ​ + ⋯ , or for two resistors R T = R 1 R 2 R 1 + R 2 R_T = \frac{R_1 R_2}{R_1 + R_2} R T ​ = R 1 ​ + R 2 ​ R 1 ​ R 2 ​ ​ (always smaller than the smallest branch).

Inductance

Series inductors (no mutual coupling): L T = L 1 + L 2 + ⋯ L_T = L_1 + L_2 + \cdots L T ​ = L 1 ​ + L 2 ​ + ⋯ — same pattern as series R . Element 3 explicitly asks for L T = L 1 + L 2 L_T = L_1 + L_2 L T ​ = L 1 ​ + L 2 ​ as the series formula.

Parallel inductors (ideal, no mutual coupling): reciprocal sum, analogous to parallel R .

Capacitance

Parallel capacitors: C T = C 1 + C 2 + C 3 C_T = C_1 + C_2 + C_3 C T ​ = C 1 ​ + C 2 ​ + C 3 ​ — add , like series R . Element 3 tests C T = C 1 + C 2 + C 3 C_T = C_1 + C_2 + C_3 C T ​ = C 1 ​ + C 2 ​ + C 3 ​ for three capacitors in parallel.

Series capacitors: reciprocal sum; total C is less than the smallest capacitor.

  • Configuration Resistances Inductances (ideal) Capacitances
  • Series Add Add Reciprocal sum
  • Parallel Reciprocal sum Reciprocal sum Add

Memory hook: Series L like series R; parallel C like series R (they add).

Energy storage and time-domain behavior (overview)

Inductor: energy E L = 1 2 L I 2 E_L = \frac{1}{2} L I^2 E L ​ = 2 1 ​ L I 2 in the magnetic field . Current through an inductor cannot change instantaneously; the coil “resists” current change with induced voltage. At switch-on, an inductor initially behaves like an open; after many time constants in a resistive circuit, DC current settles as if the inductor were a short (wire resistance only).

Capacitor: energy E C = 1 2 C V 2 E_C = \frac{1}{2} C V^2 E C ​ = 2 1 ​ C V 2 in the electric field . Voltage across a capacitor cannot change instantaneously. At switch-on to a DC source through resistance, the capacitor initially looks like a short (charging surge), then approaches an open once charged.

Time-constant sketch (RC / RL): τ = R C \tau = RC τ = RC or τ = L / R \tau = L/R τ = L / R . After about 5τ , transients are essentially settled for exam-level work. Detailed RC time-constant math returns in Topic 3-B ; here you only need the qualitative “L magnetic / C electric” storage picture and that reactance—not resistance—sets sinusoidal AC phase shift.

Practical RF component behaviors from the pool

Bypass capacitor purpose: it removes alternating current by providing a low-impedance path to ground (for the AC component), keeping DC bias undisturbed. It does not primarily “remove DC by shunting DC to ground”—that would destroy bias supplies. Think: AC short, DC open.

Reducing the inductance of an antenna coil: reduce the number of turns . Adding turns, raising core permeability, or compressing turns generally increases inductance (or coupling), not decreases it.

Conductors again (RLC topic overlap): good conductors → many free electrons ; best low-resistance metals → gold, silver, copper . Same material literacy as §6.2, now tied to minimizing R losses in coils and tank circuits.

Putting R, L, and C together on one mental schematic

Imagine a series R–L–C filter feeding an RF stage:

R sets damping and true-power loss.

L contributes X L = 2 π f L X_L = 2\pi f L X L ​ = 2 π f L and magnetic energy storage.

C contributes X C = 1 / ( 2 π f C ) X_C = 1/(2\pi f C) X C ​ = 1/ ( 2 π f C ) and electric energy storage.

Net reactance X = X L − X C X = X_L - X_C X = X L ​ − X C ​ (series convention) goes to zero at resonance—preview of later RLC circuit topics—but even before resonance math, you must compute each reactance correctly.

Parallel bypass caps on supply pins use large enough C (low enough X C X_C X C ​ at the frequencies of interest) so AC noise sees ground.

When Element 3 shows a formula stem, match symbols carefully: 2 π f L 2\pi f L 2 π f L is inductive; 1 / ( 2 π f C ) 1/(2\pi f C) 1/ ( 2 π f C ) is capacitive; series L adds; parallel C adds. Those four facts clear most of key topic 004 and the reactance item from 001 .