Study guide
19.7 Bench Repair Practices, ESD & Rework Tools
FCC General Radiotelephone Operator License GROL
Track your progress as you read
Finished sections get a check mark.
1 Introduction & GROL Exam Overview
1.1 About the General Radiotelephone Operator License 1.2 Exam Format, COLEMs, FRN & Application Process
2 Element 1: Rules & Regulations
2.1 Equipment Requirements (Part 80) 2.2 License Requirements & Operator Authority 2.3 Watchkeeping & Logkeeping Duties 2.4 Log Entries & Required Records 2.5 Ship Station Control, Inspections & International Rules
3 Element 1: Communications Procedures
3.1 Bridge-to-Bridge Operations & VTS 3.2 Distress Communications & Alerting 3.3 Operating Procedures, Calling & Testing 3.4 Urgency (PAN PAN) & Safety (SECURITE) Traffic 3.5 The GMDSS Concept & Ship Responsibilities
4 Element 1: Equipment Operations
4.1 VHF Equipment Controls 4.2 MF/HF SSB Equipment Controls 4.3 DSC Operations & Equipment Faults 4.4 VHF Channel Selection & Channel Assignments 4.5 MF/HF Frequency & Emission Selection 4.6 Required Equipment Tests & On-Air Test Procedure
5 Element 1: Other Equipment & Antennas
5.1 Marine Antennas & Polarization 5.2 EPIRBs & Emergency Beacons 5.3 Power Sources, Reserve Power & Required Tests 5.4 Search and Rescue Transponders (SARTs) 5.5 Survival Craft Portable VHF (SCT) Requirements 5.6 NAVTEX & Maritime Safety Information
6 Element 3: Electrical Principles
6.1 Electrical Elements, Units & Power Types 6.2 Magnetism & Magnetic Circuits 6.3 Resistance, Capacitance & Inductance 6.4 Waveforms & Semiconductor Introduction 6.5 Materials, Corrosion & Skin Effect 6.6 AC Measurement & Conversion Factors 6.7 Conduction, Reactive Power & Maximum Power Transfer
7 Element 3: Electrical Math
7.1 Ohm's Law — Series & Parallel Circuits 7.2 Frequency, Period, Wavelength & Waveform Math 7.3 Power Relationships & Decibels 7.4 RC/RL Time Constants 7.5 Frequency Counter Accuracy, PPM & Harmonics 7.6 Impedance in Rectangular & Polar Coordinates 7.7 Regulation, Turns Ratio, Zener Bias & Conductance
8 Element 3: Circuit Components — Passives & Power Devices
8.1 Capacitors & Photoconductive Devices 8.2 Transformers, Voltage Regulators & Zener Diodes 8.3 Diodes, SCRs & Triacs
9 Element 3: Active Components — Transistors & Devices
9.1 Bipolar Junction Transistors 9.2 FETs, LEDs & Specialty Devices 9.3 Device Selection, Ratings & Thermal Design
10 Element 3: Practical Circuits — RLC, Op Amps & Schematics
10.1 R-L-C Resonant Circuits 10.2 Op Amps, PLLs, VCOs & Mixers 10.3 Reading Schematics & Signal Flow
11 Element 3: Digital Logic
11.1 Logic Gates & Boolean Functions 11.2 Flip-Flops & Sequential Elements 11.3 Multivibrators & Timing Circuits 11.4 Microprocessors & Bus Architecture 11.5 TTL Logic Families & Input Voltage Levels 11.6 Positive & Negative Logic and Truth Tables 11.7 Memory Types & Microprocessor Concepts 11.8 Counters, Prescalers, BCD & Data Converters
12 Element 3: Receivers
12.1 Receiver Theory & Superheterodyne Architecture 12.2 RF Amplifiers & Front-End Design 12.3 Filters & Detectors 12.4 Audio, Squelch & Receiver Performance Specs 12.5 Receiver Oscillators: Colpitts, Hartley & Pierce 12.6 Mixing, Image Frequencies & Spurious Products 12.7 IF Selectivity & Filter Bandwidth
13 Element 3: Transmitters
13.1 RF Amplifier Classes & Efficiency 13.2 Oscillators, Modulators & Tuning Networks 13.3 SSB Transmitters & Modern Transmitter Technology
14 Element 3: Signals, Emissions & Modulation
14.1 Amplitude & Frequency Modulation 14.2 Single-Sideband Modulation 14.3 Pulse Modulation & Emission Types
15 Element 3: Power Sources
15.1 Batteries & Energy Storage 15.2 Motors, Generators & Power Supplies
16 Element 3: Antennas & Feed Lines
16.1 Antenna Theory, Types & Patterns 16.2 Voltage, Current & Impedance on Antennas 16.3 Transmission Lines, Velocity Factor & SWR 16.4 Effective Radiated Power & Antenna Bandwidth
17 Element 3 Background: Propagation & Radio Practice
17.1 Radio Wave Propagation Modes 17.2 Multipath, Fading & Doppler Effects 17.3 Radio Practice, Interference & Good Engineering
18 Element 3: Aircraft Radio Navigation Systems
18.1 DME & VOR 18.2 ILS, ADF & ATC Transponders 18.3 Aircraft Antennas, Frequencies & Equipment Functions
19 Element 3: Installation, Maintenance & Repair
19.1 Indicating Meters & Meter Movements 19.2 Oscilloscopes & Waveform Measurement 19.3 Measurement Procedures 19.4 Installation Codes & Bonding Procedures 19.5 Frequency Standards, SINAD Meters & EMI Hunting 19.6 Spectrum Analyzers, TDRs & Service Monitors 19.7 Bench Repair Practices, ESD & Rework Tools 19.8 Systematic Troubleshooting & Field Fault Diagnosis
20 Element 3: Communications Technology & Marine Systems
20.1 Transmission Types, Coding & Multiplexing 20.2 Signal Processing, Software & Codes 20.3 Marine VHF, MF/HF & SSB-SITOR 20.4 Survival Craft Electronics, FAX & NAVTEX 20.5 NMEA 0183 & NMEA 2000 Data Networks
21 Element 3: RADAR & Satellite Systems
21.1 RADAR Theory & Pulse Fundamentals 21.2 Range, Pulse Width & PRF 21.3 Radar Antennas & Waveguides 21.4 INMARSAT Satellite Communications 21.5 RADAR Components: Magnetron, Duplexer, ATR & Synchro 21.6 RADAR Equipment, ARPA & Radiation Safety 21.7 Low Earth Orbit Systems: Iridium & COSPAS-SARSAT 21.8 GPS Satellite Navigation & DGPS
22 Element 3: RF & Electrical Safety
22.1 RF Radiation Exposure Limits 22.2 Electrical Safety Practices for Radio Technicians
23 Study Strategy & Exam Day
23.1 Study Strategy, Practice Plan & Exam Day
19.7 Bench Repair Practices, ESD & Rework Tools
Key Takeaways Explain This Topic AI
When working with CMOS, the pool's answer is that a wrist strap must have less than 100,000 ohms of resistance to prevent static electricity
The preferred method of cleaning solder from plated-through circuit board holes is a vacuum device
Plastic wire ties are cut with flush-cut diagonal pliers, cut flush, so no sharp stub remains
The ideal method of removing insulation from wire is the thermal stripper
A hot gas bonder is used for non-contact melting of solder, and safety glasses are the most important precaution when repairing circuit board assemblies
Last updated: August 2026
19.7 Bench Repair Practices, ESD & Rework Tools
Quick Answer: Wrist strap — the pool's keyed answer is less than 100,000 ohms . Clear plated-through holes with a vacuum device . Cut wire ties flush, with flush-cut diagonal pliers . Strip insulation with a thermal stripper . A hot gas bonder does non-contact melting of solder . When repairing boards, wear safety glasses .
Sub-topic 3-L-079 (Repair Procedures) is the most hands-on sub-topic in Element 3. These are shop-floor practices, and the pool tests them because a licensed maintainer who damages equipment or injures themselves is a genuine risk.
ESD and the wrist strap
When soldering or working with CMOS electronics products or equipment, a wrist strap must have less than 100,000 ohms of resistance to prevent static electricity.
That is the exam answer , and it is the one to select. Understand the two competing requirements it sits between:
- Requirement Pushes resistance which way
- Drain static charge from the operator to ground before it can damage a device Lower
- Protect the operator by limiting current if they contact a live circuit Higher
A direct wire to ground would drain charge instantly and electrocute the technician; an open circuit protects them and drains nothing. The compromise is a resistive path. Note for the bench that current industry practice (ANSI/ESD S20.20 and IEC 61340) specifies a 1 megohm series resistor in the strap cord, tested to a path resistance typically under 35 megohms — a higher figure than the pool's. On the exam, answer 100,000 ohms; in the shop, use a 1 MΩ commercial strap.
Why CMOS specifically? A CMOS gate's insulated gate oxide is only nanometres thick and punctures at a few tens of volts across it. Simply walking across a carpeted floor can put several kilovolts on a human body. The damage is frequently latent — the device works on the bench and fails weeks later in service, which is the worst possible outcome on a vessel at sea.
Desoldering plated-through holes
Which of the following is the preferred method of cleaning solder from plated-through circuit-board holes? Use a vacuum device.
A plated-through hole carries a thin copper barrel connecting the layers. That barrel is the fragile part. A vacuum desoldering tool — a solder sucker or, better, a vacuum desoldering station with a heated hollow tip — melts the solder and draws it out axially , leaving the barrel intact and the hole open for the new lead.
- Method Problem
- Vacuum device None — the pool's answer
- Solder wick / braid alone Works on pads, but drags across the barrel and can lift it
- Pushing the lead out with a pick Tears the barrel and breaks the interlayer connection
- Drilling Destroys the plating entirely
Once a barrel is torn out the layer-to-layer connection is gone and the repair needs a through-board jumper — far more work than doing it right the first time.
Wire ties
What is the proper way to cut plastic wire ties? With flush-cut diagonal pliers and cut flush.
Both halves matter: the right tool and the right result . An ordinary side-cutter leaves an angled stub that is genuinely sharp — sharp enough to lacerate a hand reaching into a loom, and sharp enough to chafe insulation on an adjacent conductor over time with vibration. On an aircraft or a vessel, both consequences are serious.
Cut flush with the head , and cut ties hand-tight rather than crushing the bundle; over-tensioned ties deform insulation and create the very chafe point the tie was meant to prevent.
Stripping insulation
The ideal method of removing insulation from wire is the thermal stripper.
A thermal stripper melts or vaporises the insulation with a heated element and lifts it away without touching the conductor at all . That matters because a mechanical stripper set even slightly undersized nicks the strands , and a nicked strand is a stress riser that eventually fails from vibration — in a mast loom or an airframe, exactly where you cannot reach it.
- Method Risk to conductor
- Thermal stripper None — the pool's ideal
- Precision mechanical stripper, correct gauge Low if set correctly
- Adjustable stripper set by eye Nicks strands
- Knife High — the worst option
Thermal stripping also handles the tough insulations found in aviation and marine wiring (PTFE, Kapton, Tefzel) that resist mechanical strippers.
The hot gas bonder
A "hot gas bonder" is used for non-contact melting of solder.
Hot gas — usually filtered air or nitrogen — is directed at a joint through a nozzle, melting the solder without any tool touching the board . Two reasons this matters:
Surface-mount rework. A fine-pitch QFP or a BGA cannot be removed with an iron; hot gas reflows every joint of the package simultaneously.
Fragile assemblies. No mechanical force is applied to pads, so nothing lifts.
Key the answer on the phrase non-contact . The distractors describe contact methods.
The overriding safety rule
When repairing circuit board assemblies it is most important to: wear safety glasses.
The pool asks what is most important, and the answer is eye protection. The hazards are specific and common:
- Solder spits when flux boils, especially on a damp or contaminated joint
- Clipped component leads launch at speed when cut
- Wire tie ends and stripped insulation flick unpredictably
- Solvents and flux removers splash
- Electrolytic capacitors vent, and a reverse-biased or overvoltaged one can rupture
None of these is exotic; all of them happen at ordinary benches, and the eye has no protection of its own. Every other good practice in this section protects the equipment — this one protects you , which is why it ranks first.