Study guide

21.8 GPS Satellite Navigation & DGPS

FCC General Radiotelephone Operator License GROL

Track your progress as you read

Finished sections get a check mark.

1 Introduction & GROL Exam Overview

1.1 About the General Radiotelephone Operator License 1.2 Exam Format, COLEMs, FRN & Application Process

2 Element 1: Rules & Regulations

2.1 Equipment Requirements (Part 80) 2.2 License Requirements & Operator Authority 2.3 Watchkeeping & Logkeeping Duties 2.4 Log Entries & Required Records 2.5 Ship Station Control, Inspections & International Rules

3 Element 1: Communications Procedures

3.1 Bridge-to-Bridge Operations & VTS 3.2 Distress Communications & Alerting 3.3 Operating Procedures, Calling & Testing 3.4 Urgency (PAN PAN) & Safety (SECURITE) Traffic 3.5 The GMDSS Concept & Ship Responsibilities

4 Element 1: Equipment Operations

4.1 VHF Equipment Controls 4.2 MF/HF SSB Equipment Controls 4.3 DSC Operations & Equipment Faults 4.4 VHF Channel Selection & Channel Assignments 4.5 MF/HF Frequency & Emission Selection 4.6 Required Equipment Tests & On-Air Test Procedure

5 Element 1: Other Equipment & Antennas

5.1 Marine Antennas & Polarization 5.2 EPIRBs & Emergency Beacons 5.3 Power Sources, Reserve Power & Required Tests 5.4 Search and Rescue Transponders (SARTs) 5.5 Survival Craft Portable VHF (SCT) Requirements 5.6 NAVTEX & Maritime Safety Information

6 Element 3: Electrical Principles

6.1 Electrical Elements, Units & Power Types 6.2 Magnetism & Magnetic Circuits 6.3 Resistance, Capacitance & Inductance 6.4 Waveforms & Semiconductor Introduction 6.5 Materials, Corrosion & Skin Effect 6.6 AC Measurement & Conversion Factors 6.7 Conduction, Reactive Power & Maximum Power Transfer

7 Element 3: Electrical Math

7.1 Ohm's Law — Series & Parallel Circuits 7.2 Frequency, Period, Wavelength & Waveform Math 7.3 Power Relationships & Decibels 7.4 RC/RL Time Constants 7.5 Frequency Counter Accuracy, PPM & Harmonics 7.6 Impedance in Rectangular & Polar Coordinates 7.7 Regulation, Turns Ratio, Zener Bias & Conductance

8 Element 3: Circuit Components — Passives & Power Devices

8.1 Capacitors & Photoconductive Devices 8.2 Transformers, Voltage Regulators & Zener Diodes 8.3 Diodes, SCRs & Triacs

9 Element 3: Active Components — Transistors & Devices

9.1 Bipolar Junction Transistors 9.2 FETs, LEDs & Specialty Devices 9.3 Device Selection, Ratings & Thermal Design

10 Element 3: Practical Circuits — RLC, Op Amps & Schematics

10.1 R-L-C Resonant Circuits 10.2 Op Amps, PLLs, VCOs & Mixers 10.3 Reading Schematics & Signal Flow

11 Element 3: Digital Logic

11.1 Logic Gates & Boolean Functions 11.2 Flip-Flops & Sequential Elements 11.3 Multivibrators & Timing Circuits 11.4 Microprocessors & Bus Architecture 11.5 TTL Logic Families & Input Voltage Levels 11.6 Positive & Negative Logic and Truth Tables 11.7 Memory Types & Microprocessor Concepts 11.8 Counters, Prescalers, BCD & Data Converters

12 Element 3: Receivers

12.1 Receiver Theory & Superheterodyne Architecture 12.2 RF Amplifiers & Front-End Design 12.3 Filters & Detectors 12.4 Audio, Squelch & Receiver Performance Specs 12.5 Receiver Oscillators: Colpitts, Hartley & Pierce 12.6 Mixing, Image Frequencies & Spurious Products 12.7 IF Selectivity & Filter Bandwidth

13 Element 3: Transmitters

13.1 RF Amplifier Classes & Efficiency 13.2 Oscillators, Modulators & Tuning Networks 13.3 SSB Transmitters & Modern Transmitter Technology

14 Element 3: Signals, Emissions & Modulation

14.1 Amplitude & Frequency Modulation 14.2 Single-Sideband Modulation 14.3 Pulse Modulation & Emission Types

15 Element 3: Power Sources

15.1 Batteries & Energy Storage 15.2 Motors, Generators & Power Supplies

16 Element 3: Antennas & Feed Lines

16.1 Antenna Theory, Types & Patterns 16.2 Voltage, Current & Impedance on Antennas 16.3 Transmission Lines, Velocity Factor & SWR 16.4 Effective Radiated Power & Antenna Bandwidth

17 Element 3 Background: Propagation & Radio Practice

17.1 Radio Wave Propagation Modes 17.2 Multipath, Fading & Doppler Effects 17.3 Radio Practice, Interference & Good Engineering

18 Element 3: Aircraft Radio Navigation Systems

18.1 DME & VOR 18.2 ILS, ADF & ATC Transponders 18.3 Aircraft Antennas, Frequencies & Equipment Functions

19 Element 3: Installation, Maintenance & Repair

19.1 Indicating Meters & Meter Movements 19.2 Oscilloscopes & Waveform Measurement 19.3 Measurement Procedures 19.4 Installation Codes & Bonding Procedures 19.5 Frequency Standards, SINAD Meters & EMI Hunting 19.6 Spectrum Analyzers, TDRs & Service Monitors 19.7 Bench Repair Practices, ESD & Rework Tools 19.8 Systematic Troubleshooting & Field Fault Diagnosis

20 Element 3: Communications Technology & Marine Systems

20.1 Transmission Types, Coding & Multiplexing 20.2 Signal Processing, Software & Codes 20.3 Marine VHF, MF/HF & SSB-SITOR 20.4 Survival Craft Electronics, FAX & NAVTEX 20.5 NMEA 0183 & NMEA 2000 Data Networks

21 Element 3: RADAR & Satellite Systems

21.1 RADAR Theory & Pulse Fundamentals 21.2 Range, Pulse Width & PRF 21.3 Radar Antennas & Waveguides 21.4 INMARSAT Satellite Communications 21.5 RADAR Components: Magnetron, Duplexer, ATR & Synchro 21.6 RADAR Equipment, ARPA & Radiation Safety 21.7 Low Earth Orbit Systems: Iridium & COSPAS-SARSAT 21.8 GPS Satellite Navigation & DGPS

22 Element 3: RF & Electrical Safety

22.1 RF Radiation Exposure Limits 22.2 Electrical Safety Practices for Radio Technicians

23 Study Strategy & Exam Day

23.1 Study Strategy, Practice Plan & Exam Day

21.8 GPS Satellite Navigation & DGPS

Key Takeaways Explain This Topic AI

GPS satellites orbit at an altitude of 12,554 miles and transmit on 1227.6 MHz and 1575.4 MHz

Twenty-four GPS satellites are normally in operation

The satellites occupy six orbital planes, equally spaced and inclined about 55 degrees to the equator

Four satellites must be received to provide complete position and time - three for position plus one to resolve receiver clock error

  • DGPS is a system providing additional correction factors to improve position accuracy
  • Last updated: August 2026

21.8 GPS Satellite Navigation & DGPS

Quick Answer: GPS orbits at 12,554 miles , transmits on 1227.6 MHz and 1575.4 MHz , uses 24 satellites in six orbital planes equally spaced and inclined about 55° to the equator . Four satellites are needed for complete position and time . DGPS provides additional correction factors to improve position accuracy .

Sub-topic 3-P-098 (GPS) is six factual items with no calculation. GPS is also the single most operationally important system in this chapter for a GROL holder, because a DSC distress alert without a position is a fraction as useful — and that position comes from GPS over NMEA (sections 19.8, 20.5).

The constellation

  • Parameter Value
  • Orbiting altitude 12,554 miles
  • Satellites normally in operation 24
  • Orbital planes Six , equally spaced
  • Inclination About 55° to the equator
  • Orbital period About 12 hours (two orbits per sidereal day)

What best describes the GPS satellites' orbits? They are in six orbital planes equally spaced and inclined about 55 degrees to the equator.

The geometry is deliberate. Six planes of four satellites each, inclined at 55°, guarantees that at least four satellites are above the horizon from anywhere on Earth at any time — which is exactly the number a receiver needs. The 55° inclination is a compromise: high enough to give useful coverage at high latitudes, low enough to concentrate satellites where most users are.

Note that GPS is medium earth orbit — well above the LEO constellations of section 21.7 (Iridium at 485 miles) but far below geostationary (22,300 miles). The 12-hour period means the constellation repeats its ground track daily, which is why GPS reception geometry at a fixed site is similar day to day.

The frequencies

The GPS transmitted frequencies are 1227.6 MHz and 1575.4 MHz.

  • Designation Frequency Traditional use
  • L1 1575.4 MHz Civilian C/A code plus the military P(Y) code
  • L2 1227.6 MHz Traditionally military; used by survey receivers for ionospheric correction

Both are in L-band , alongside Iridium (1616–1626 MHz) and Inmarsat. The choice is deliberate: L-band passes through cloud and rain with minimal attenuation, and works with a small patch antenna that needs no aiming — essential for a system meant to work on a moving vessel, aircraft or handheld.

The reason two frequencies exist is worth knowing: the ionosphere delays the signal by an amount that depends on frequency . A receiver that tracks both L1 and L2 can measure that delay directly and cancel most of it, which is why dual-frequency survey receivers are far more accurate than single-frequency ones.

Why four satellites

How many satellites must be received to provide complete position and time? Four.

The reasoning is genuinely elegant and the pool rewards understanding it.

GPS positioning is trilateration by timing . Each satellite broadcasts its position and a precisely timed signal; the receiver measures the travel time and multiplies by the speed of light to get a range. In principle:

  • Satellites What it resolves
  • 1 A sphere of possible positions
  • 2 A circle where two spheres intersect
  • 3 Two points — geometry alone resolves position
  • 4 Position AND time

So why not three? Because the range measurements depend on the receiver knowing the exact time. Satellites carry atomic clocks; a receiver carries a cheap crystal. A clock error of one microsecond produces a range error of about 300 metres , so an uncorrected receiver clock ruins the fix.

The fourth satellite supplies the fourth equation needed to solve for the fourth unknown — the receiver clock offset — alongside latitude, longitude and altitude. The receiver effectively calculates the exact time as part of the fix. That is why a GPS receiver is also a superb time standard, and why "position and time" is the pool's phrasing.

DGPS

What is DGPS? A system to provide additional correction factors to improve position accuracy.

Differential GPS works on a simple insight: the dominant GPS errors are common to receivers in the same region. Ionospheric delay, tropospheric delay, satellite clock drift and orbit (ephemeris) error affect a reference station and a nearby vessel almost identically.

So a reference receiver at a precisely surveyed location compares its computed position against its known true position, derives per-satellite corrections, and broadcasts them. Any receiver within range applies the corrections and removes most of the shared error.

Error source Corrected by DGPS?

  • Ionospheric delay Yes — largely common
  • Tropospheric delay Yes — largely common
  • Satellite clock and ephemeris error Yes — identical for all users of that satellite
  • Multipath at the user's own antenna No — purely local
  • Receiver noise No — purely local

In the maritime world the corrections are traditionally broadcast by coastal radiobeacons in the 285–325 kHz band , received by a separate DGPS beacon receiver and fed to the GPS set. Accuracy typically improves from tens of metres to a few metres — which matters for harbour approaches, buoy positioning and cable work. The same principle underlies WAAS, EGNOS and modern RTK surveying, each with a different delivery path but the same idea: measure the shared error somewhere known, then subtract it.