Study guide
21.7 Low Earth Orbit Systems: Iridium & COSPAS-SARSAT
FCC General Radiotelephone Operator License GROL
Track your progress as you read
Finished sections get a check mark.
1 Introduction & GROL Exam Overview
1.1 About the General Radiotelephone Operator License 1.2 Exam Format, COLEMs, FRN & Application Process
2 Element 1: Rules & Regulations
2.1 Equipment Requirements (Part 80) 2.2 License Requirements & Operator Authority 2.3 Watchkeeping & Logkeeping Duties 2.4 Log Entries & Required Records 2.5 Ship Station Control, Inspections & International Rules
3 Element 1: Communications Procedures
3.1 Bridge-to-Bridge Operations & VTS 3.2 Distress Communications & Alerting 3.3 Operating Procedures, Calling & Testing 3.4 Urgency (PAN PAN) & Safety (SECURITE) Traffic 3.5 The GMDSS Concept & Ship Responsibilities
4 Element 1: Equipment Operations
4.1 VHF Equipment Controls 4.2 MF/HF SSB Equipment Controls 4.3 DSC Operations & Equipment Faults 4.4 VHF Channel Selection & Channel Assignments 4.5 MF/HF Frequency & Emission Selection 4.6 Required Equipment Tests & On-Air Test Procedure
5 Element 1: Other Equipment & Antennas
5.1 Marine Antennas & Polarization 5.2 EPIRBs & Emergency Beacons 5.3 Power Sources, Reserve Power & Required Tests 5.4 Search and Rescue Transponders (SARTs) 5.5 Survival Craft Portable VHF (SCT) Requirements 5.6 NAVTEX & Maritime Safety Information
6 Element 3: Electrical Principles
6.1 Electrical Elements, Units & Power Types 6.2 Magnetism & Magnetic Circuits 6.3 Resistance, Capacitance & Inductance 6.4 Waveforms & Semiconductor Introduction 6.5 Materials, Corrosion & Skin Effect 6.6 AC Measurement & Conversion Factors 6.7 Conduction, Reactive Power & Maximum Power Transfer
7 Element 3: Electrical Math
7.1 Ohm's Law — Series & Parallel Circuits 7.2 Frequency, Period, Wavelength & Waveform Math 7.3 Power Relationships & Decibels 7.4 RC/RL Time Constants 7.5 Frequency Counter Accuracy, PPM & Harmonics 7.6 Impedance in Rectangular & Polar Coordinates 7.7 Regulation, Turns Ratio, Zener Bias & Conductance
8 Element 3: Circuit Components — Passives & Power Devices
8.1 Capacitors & Photoconductive Devices 8.2 Transformers, Voltage Regulators & Zener Diodes 8.3 Diodes, SCRs & Triacs
9 Element 3: Active Components — Transistors & Devices
9.1 Bipolar Junction Transistors 9.2 FETs, LEDs & Specialty Devices 9.3 Device Selection, Ratings & Thermal Design
10 Element 3: Practical Circuits — RLC, Op Amps & Schematics
10.1 R-L-C Resonant Circuits 10.2 Op Amps, PLLs, VCOs & Mixers 10.3 Reading Schematics & Signal Flow
11 Element 3: Digital Logic
11.1 Logic Gates & Boolean Functions 11.2 Flip-Flops & Sequential Elements 11.3 Multivibrators & Timing Circuits 11.4 Microprocessors & Bus Architecture 11.5 TTL Logic Families & Input Voltage Levels 11.6 Positive & Negative Logic and Truth Tables 11.7 Memory Types & Microprocessor Concepts 11.8 Counters, Prescalers, BCD & Data Converters
12 Element 3: Receivers
12.1 Receiver Theory & Superheterodyne Architecture 12.2 RF Amplifiers & Front-End Design 12.3 Filters & Detectors 12.4 Audio, Squelch & Receiver Performance Specs 12.5 Receiver Oscillators: Colpitts, Hartley & Pierce 12.6 Mixing, Image Frequencies & Spurious Products 12.7 IF Selectivity & Filter Bandwidth
13 Element 3: Transmitters
13.1 RF Amplifier Classes & Efficiency 13.2 Oscillators, Modulators & Tuning Networks 13.3 SSB Transmitters & Modern Transmitter Technology
14 Element 3: Signals, Emissions & Modulation
14.1 Amplitude & Frequency Modulation 14.2 Single-Sideband Modulation 14.3 Pulse Modulation & Emission Types
15 Element 3: Power Sources
15.1 Batteries & Energy Storage 15.2 Motors, Generators & Power Supplies
16 Element 3: Antennas & Feed Lines
16.1 Antenna Theory, Types & Patterns 16.2 Voltage, Current & Impedance on Antennas 16.3 Transmission Lines, Velocity Factor & SWR 16.4 Effective Radiated Power & Antenna Bandwidth
17 Element 3 Background: Propagation & Radio Practice
17.1 Radio Wave Propagation Modes 17.2 Multipath, Fading & Doppler Effects 17.3 Radio Practice, Interference & Good Engineering
18 Element 3: Aircraft Radio Navigation Systems
18.1 DME & VOR 18.2 ILS, ADF & ATC Transponders 18.3 Aircraft Antennas, Frequencies & Equipment Functions
19 Element 3: Installation, Maintenance & Repair
19.1 Indicating Meters & Meter Movements 19.2 Oscilloscopes & Waveform Measurement 19.3 Measurement Procedures 19.4 Installation Codes & Bonding Procedures 19.5 Frequency Standards, SINAD Meters & EMI Hunting 19.6 Spectrum Analyzers, TDRs & Service Monitors 19.7 Bench Repair Practices, ESD & Rework Tools 19.8 Systematic Troubleshooting & Field Fault Diagnosis
20 Element 3: Communications Technology & Marine Systems
20.1 Transmission Types, Coding & Multiplexing 20.2 Signal Processing, Software & Codes 20.3 Marine VHF, MF/HF & SSB-SITOR 20.4 Survival Craft Electronics, FAX & NAVTEX 20.5 NMEA 0183 & NMEA 2000 Data Networks
21 Element 3: RADAR & Satellite Systems
21.1 RADAR Theory & Pulse Fundamentals 21.2 Range, Pulse Width & PRF 21.3 Radar Antennas & Waveguides 21.4 INMARSAT Satellite Communications 21.5 RADAR Components: Magnetron, Duplexer, ATR & Synchro 21.6 RADAR Equipment, ARPA & Radiation Safety 21.7 Low Earth Orbit Systems: Iridium & COSPAS-SARSAT 21.8 GPS Satellite Navigation & DGPS
22 Element 3: RF & Electrical Safety
22.1 RF Radiation Exposure Limits 22.2 Electrical Safety Practices for Radio Technicians
23 Study Strategy & Exam Day
23.1 Study Strategy, Practice Plan & Exam Day
21.7 Low Earth Orbit Systems: Iridium & COSPAS-SARSAT
Key Takeaways Explain This Topic AI
The Iridium satellite constellation orbits at an altitude of 485 miles and uses 1616-1626 MHz for telephone and messaging
Iridium provides digital voice and data at 2.4 kbps, with 48 spot beams per satellite and a footprint about 30 miles in diameter per beam
The main function of the COSPAS-SARSAT satellite system is to monitor 406 MHz for distress calls from EPIRBs
COSPAS-SARSAT determines the position of a ship in distress by measuring the Doppler shift of the 406 MHz signal at several different points in its orbit
Low earth orbit gives short path delay and polar coverage, which is why Iridium and COSPAS-SARSAT work where geostationary Inmarsat does not
Last updated: August 2026
21.7 Low Earth Orbit Systems: Iridium & COSPAS-SARSAT
Quick Answer: Iridium : orbit 485 miles , band 1616–1626 MHz , digital voice and data at 2.4 kbps , 48 spot beams per satellite with a 30-mile footprint each. COSPAS-SARSAT : monitors 406 MHz for distress calls from EPIRBs , and fixes position by measuring the Doppler shift of the 406 MHz signal at several different points in its orbit .
Sub-topic 3-P-095 (Low Earth Orbit Systems) covers the two LEO constellations a marine technician meets. It pairs naturally with the geostationary Inmarsat material, because the contrast between the two orbit types explains everything about what each system can do.
Why low earth orbit at all
- Geostationary (Inmarsat) Low earth orbit (Iridium, COSPAS-SARSAT)
- Altitude ~22,300 miles ~485 miles (Iridium)
- Coverage Near-global except the poles Including the poles
- Path delay ~250 ms round trip Tens of milliseconds
- Terminal power / antenna Higher gain needed Modest — a handset works
- Satellites needed 3–4 Dozens
Two consequences drive everything else. First, a geostationary satellite sits above the equator, so from high latitudes it is at or below the horizon — which is exactly why sea area A4 (the polar regions) is defined as the area outside Inmarsat coverage, and why LEO systems matter there. Second, because a LEO satellite is roughly 46 times closer , path loss is dramatically lower and a handheld terminal becomes practical.
Iridium: the numbers
The pool asks four separate factual items about Iridium, so learn them as a block:
- Parameter Value
- Orbiting altitude 485 miles
- Frequency band (telephone and messaging) 1616–1626 MHz
- Services provided Digital voice and data at 2.4 kbps
- Spot beams 48 per satellite , footprint about 30 miles in diameter
A few notes that make the numbers stick:
1616–1626 MHz is in L-band , the same general region as GPS (1227.6 and 1575.4 MHz, section 21.8) and Inmarsat. L-band is used for mobile satellite service because it penetrates weather with minimal rain fade and works with small, non-tracking antennas.
2.4 kbps sounds slow, and it is — Iridium was designed around voice and short messaging , not broadband. For a GROL technician the relevance is that a vessel's Iridium terminal is for telephony, position reporting and short data, not for bulk transfer.
48 spot beams per satellite is how the constellation reuses its limited spectrum: each satellite paints its coverage as a honeycomb of small beams, and the same frequencies serve non-adjacent beams simultaneously — the same cellular principle used on land, projected from orbit.
Because the satellites move fast relative to the ground, a call is handed off between beams and between satellites during a conversation, which is why the system needs inter-satellite links.
COSPAS-SARSAT
What is the main function of the COSPAS-SARSAT satellite system? Monitor 406 MHz for distress calls from EPIRBs.
COSPAS-SARSAT is the alerting backbone of GMDSS. It is an international, government-run, non-commercial system whose only job is to detect and locate distress beacons — EPIRBs at sea (section 5.2), ELTs in aircraft, and PLBs carried by individuals.
406 MHz is the frequency to remember. It is dedicated to satellite distress alerting, and a 406 MHz beacon transmits a digitally coded burst carrying a unique identity that ties back to a registration database — vessel name, owner, emergency contacts.
Position by Doppler shift
How does the COSPAS-SARSAT satellite system determine the position of a ship in distress? By measuring the Doppler shift of the 406 MHz signal taken at several different points in its orbit.
This is the elegant part, and worth understanding rather than memorising.
A LEO satellite passing overhead is moving fast relative to the beacon. As it approaches, the received frequency is shifted up ; as it recedes, shifted down . The instant of zero Doppler shift — the moment the frequency crosses the beacon's true value — occurs at the satellite's closest approach . The rate at which the shift changes through that crossing indicates how close the pass was.
Take those measurements at several points along the orbital pass, combine them with the precisely known satellite ephemeris, and the beacon's position falls out — typically to within a few kilometres, with no position data required from the beacon at all.
Two practical points follow:
Doppler location needs relative motion , so it works with LEO satellites, not geostationary ones. The geostationary part of COSPAS-SARSAT provides instant alerting but no Doppler position.
A modern GPS-equipped EPIRB transmits its own position inside the 406 MHz message, giving a fix in minutes instead of the up-to-an-hour wait for a suitable satellite pass. Doppler remains the fallback and remains the pool's answer.
Recall from section 5.2 that COSPAS-SARSAT is the international satellite-based SAR system that detects and locates 406 MHz EPIRB alerts — the same fact framed from the Element 1 side.