Study guide

21.5 RADAR Components: Magnetron, Duplexer, ATR & Synchro

FCC General Radiotelephone Operator License GROL

Track your progress as you read

Finished sections get a check mark.

1 Introduction & GROL Exam Overview

1.1 About the General Radiotelephone Operator License 1.2 Exam Format, COLEMs, FRN & Application Process

2 Element 1: Rules & Regulations

2.1 Equipment Requirements (Part 80) 2.2 License Requirements & Operator Authority 2.3 Watchkeeping & Logkeeping Duties 2.4 Log Entries & Required Records 2.5 Ship Station Control, Inspections & International Rules

3 Element 1: Communications Procedures

3.1 Bridge-to-Bridge Operations & VTS 3.2 Distress Communications & Alerting 3.3 Operating Procedures, Calling & Testing 3.4 Urgency (PAN PAN) & Safety (SECURITE) Traffic 3.5 The GMDSS Concept & Ship Responsibilities

4 Element 1: Equipment Operations

4.1 VHF Equipment Controls 4.2 MF/HF SSB Equipment Controls 4.3 DSC Operations & Equipment Faults 4.4 VHF Channel Selection & Channel Assignments 4.5 MF/HF Frequency & Emission Selection 4.6 Required Equipment Tests & On-Air Test Procedure

5 Element 1: Other Equipment & Antennas

5.1 Marine Antennas & Polarization 5.2 EPIRBs & Emergency Beacons 5.3 Power Sources, Reserve Power & Required Tests 5.4 Search and Rescue Transponders (SARTs) 5.5 Survival Craft Portable VHF (SCT) Requirements 5.6 NAVTEX & Maritime Safety Information

6 Element 3: Electrical Principles

6.1 Electrical Elements, Units & Power Types 6.2 Magnetism & Magnetic Circuits 6.3 Resistance, Capacitance & Inductance 6.4 Waveforms & Semiconductor Introduction 6.5 Materials, Corrosion & Skin Effect 6.6 AC Measurement & Conversion Factors 6.7 Conduction, Reactive Power & Maximum Power Transfer

7 Element 3: Electrical Math

7.1 Ohm's Law — Series & Parallel Circuits 7.2 Frequency, Period, Wavelength & Waveform Math 7.3 Power Relationships & Decibels 7.4 RC/RL Time Constants 7.5 Frequency Counter Accuracy, PPM & Harmonics 7.6 Impedance in Rectangular & Polar Coordinates 7.7 Regulation, Turns Ratio, Zener Bias & Conductance

8 Element 3: Circuit Components — Passives & Power Devices

8.1 Capacitors & Photoconductive Devices 8.2 Transformers, Voltage Regulators & Zener Diodes 8.3 Diodes, SCRs & Triacs

9 Element 3: Active Components — Transistors & Devices

9.1 Bipolar Junction Transistors 9.2 FETs, LEDs & Specialty Devices 9.3 Device Selection, Ratings & Thermal Design

10 Element 3: Practical Circuits — RLC, Op Amps & Schematics

10.1 R-L-C Resonant Circuits 10.2 Op Amps, PLLs, VCOs & Mixers 10.3 Reading Schematics & Signal Flow

11 Element 3: Digital Logic

11.1 Logic Gates & Boolean Functions 11.2 Flip-Flops & Sequential Elements 11.3 Multivibrators & Timing Circuits 11.4 Microprocessors & Bus Architecture 11.5 TTL Logic Families & Input Voltage Levels 11.6 Positive & Negative Logic and Truth Tables 11.7 Memory Types & Microprocessor Concepts 11.8 Counters, Prescalers, BCD & Data Converters

12 Element 3: Receivers

12.1 Receiver Theory & Superheterodyne Architecture 12.2 RF Amplifiers & Front-End Design 12.3 Filters & Detectors 12.4 Audio, Squelch & Receiver Performance Specs 12.5 Receiver Oscillators: Colpitts, Hartley & Pierce 12.6 Mixing, Image Frequencies & Spurious Products 12.7 IF Selectivity & Filter Bandwidth

13 Element 3: Transmitters

13.1 RF Amplifier Classes & Efficiency 13.2 Oscillators, Modulators & Tuning Networks 13.3 SSB Transmitters & Modern Transmitter Technology

14 Element 3: Signals, Emissions & Modulation

14.1 Amplitude & Frequency Modulation 14.2 Single-Sideband Modulation 14.3 Pulse Modulation & Emission Types

15 Element 3: Power Sources

15.1 Batteries & Energy Storage 15.2 Motors, Generators & Power Supplies

16 Element 3: Antennas & Feed Lines

16.1 Antenna Theory, Types & Patterns 16.2 Voltage, Current & Impedance on Antennas 16.3 Transmission Lines, Velocity Factor & SWR 16.4 Effective Radiated Power & Antenna Bandwidth

17 Element 3 Background: Propagation & Radio Practice

17.1 Radio Wave Propagation Modes 17.2 Multipath, Fading & Doppler Effects 17.3 Radio Practice, Interference & Good Engineering

18 Element 3: Aircraft Radio Navigation Systems

18.1 DME & VOR 18.2 ILS, ADF & ATC Transponders 18.3 Aircraft Antennas, Frequencies & Equipment Functions

19 Element 3: Installation, Maintenance & Repair

19.1 Indicating Meters & Meter Movements 19.2 Oscilloscopes & Waveform Measurement 19.3 Measurement Procedures 19.4 Installation Codes & Bonding Procedures 19.5 Frequency Standards, SINAD Meters & EMI Hunting 19.6 Spectrum Analyzers, TDRs & Service Monitors 19.7 Bench Repair Practices, ESD & Rework Tools 19.8 Systematic Troubleshooting & Field Fault Diagnosis

20 Element 3: Communications Technology & Marine Systems

20.1 Transmission Types, Coding & Multiplexing 20.2 Signal Processing, Software & Codes 20.3 Marine VHF, MF/HF & SSB-SITOR 20.4 Survival Craft Electronics, FAX & NAVTEX 20.5 NMEA 0183 & NMEA 2000 Data Networks

21 Element 3: RADAR & Satellite Systems

21.1 RADAR Theory & Pulse Fundamentals 21.2 Range, Pulse Width & PRF 21.3 Radar Antennas & Waveguides 21.4 INMARSAT Satellite Communications 21.5 RADAR Components: Magnetron, Duplexer, ATR & Synchro 21.6 RADAR Equipment, ARPA & Radiation Safety 21.7 Low Earth Orbit Systems: Iridium & COSPAS-SARSAT 21.8 GPS Satellite Navigation & DGPS

22 Element 3: RF & Electrical Safety

22.1 RF Radiation Exposure Limits 22.2 Electrical Safety Practices for Radio Technicians

23 Study Strategy & Exam Day

23.1 Study Strategy, Practice Plan & Exam Day

21.5 RADAR Components: Magnetron, Duplexer, ATR & Synchro

Key Takeaways Explain This Topic AI

The magnetron is the component providing the transmitter output power for a RADAR system

The duplexer or circulator is an electronic switch that allows one antenna to be used for both transmission and reception

The ATR box prevents the received signal from entering the transmitter

A synchro transmitter and receiver transmits the angular position of the antenna to the indicator unit

An echo box is the device used to determine the performance of a RADAR system at sea, and DSP of radar signals improves weak signal or target enhancement

Last updated: August 2026

21.5 RADAR Components: Magnetron, Duplexer, ATR & Synchro

Quick Answer: Magnetron = transmitter output power. Duplexer/circulator = electronic switch letting one antenna transmit and receive. ATR box = prevents the received signal from entering the transmitter . Synchro transmitter and receiver = carries the antenna's angular position to the indicator. Echo box = checks radar performance at sea . DSP = improved weak signal or target enhancement .

Sub-topic 3-O-091 (Components) is a naming exercise, but the components make sense as a set once you see the problem they collectively solve: one antenna must transmit kilowatts and then receive microwatts, milliseconds later, without destroying the receiver.

The magnetron

The component or circuit providing the transmitter output power for a RADAR system is the magnetron.

A magnetron is a cavity oscillator — a vacuum tube in which electrons spiralling in crossed electric and magnetic fields excite resonant cavities machined into a copper anode block. It is not an amplifier; it generates the pulse itself. Marine navigational radars use magnetrons because they deliver kilowatts of peak pulse power at 9 GHz cheaply, compactly and reliably.

Two properties worth knowing:

  • Property Consequence
  • Frequency set by cavity dimensions Non-tunable in service; a replacement must match
  • Very high peak power, low average power Duty cycle is tiny — see section 21.2
  • Wears out Magnetrons weaken with hours and with abuse; performance degrades gradually
  • The duplexer, the TR and the ATR

What is the purpose or function of the RADAR duplexer/circulator? It is an electronic switch that allows the use of one antenna for both transmission and reception.

The magnetron produces kilowatts. The receiver front end is destroyed by milliwatts. They share one antenna. The duplexer resolves this by switching, at microsecond speed, between two paths:

  • Phase Duplexer action
  • Transmit Connects magnetron → antenna; isolates the receiver
  • Receive Connects antenna → receiver; isolates the transmitter

Two gas-filled or solid-state switching elements do the work, and the pool tests them by name:

TR (transmit-receive) box — fires during transmit to short the receiver path , protecting the receiver from the outgoing pulse.

ATR (anti-transmit-receive) box — prevents the received signal from entering the transmitter. During receive, the ATR blocks the magnetron branch so the faint echo goes to the receiver instead of being wasted down a dead transmitter path.

Learn the ATR by its keyed sentence. TR protects the receiver from the transmitter ; ATR keeps the received signal out of the transmitter . The pool asks only the ATR direction, and the distractors invert it.

A circulator is the modern solid-state equivalent: a ferrite device that routes energy one way around three ports, so power entering port 1 leaves at port 2 (the antenna) and energy entering port 2 leaves at port 3 (the receiver) — never back toward the transmitter.

The synchro pair

What is the purpose of a synchro transmitter and receiver? Transmits the angular position of the antenna to the indicator unit.

A radar display is useless without bearing. The scanner rotates on the mast; the display is on the bridge. A synchro pair solves the problem electromechanically: a synchro transmitter geared to the antenna shaft produces a set of three-phase-like stator voltages encoding shaft angle, and a synchro receiver in the indicator reproduces that angle exactly.

The elegance is that no counting, no reference pulse and no calibration is needed — the receiver's rotor simply follows the transmitter's rotor. Modern radars replace synchros with optical encoders and digital bearing data, but the function is unchanged and the pool asks the classic name.

The echo box

What device can be used to determine the performance of a RADAR system at sea? An echo box.

An echo box is a resonant cavity coupled to the radar. The transmitted pulse rings it; the cavity re-radiates a decaying signal that the radar receives as an artificial target. The duration of the ringing — measured as the length of the "sun-burst" or plume on the display — indicates overall system performance.

Why it is the right tool at sea :

It exercises the whole chain — transmitter power, duplexer, antenna, receiver sensitivity — in one measurement

It gives a repeatable number for trend monitoring; a shortening plume means the system is degrading, usually a weakening magnetron

It needs no external target, no shore reference and no test range

That last point is decisive. You cannot take a vessel to a calibrated range mid-ocean, but you can key the radar into an echo box on the mast in any conditions.

Digital signal processing

Digital signal processing (DSP) of RADAR signals (compared with analog) causes improved weak signal or target enhancement.

DSP integrates successive returns from the same bearing and range cell. A genuine target returns consistently scan after scan; sea clutter and receiver noise are random . Averaging therefore builds the target and suppresses the noise, pulling a small vessel or a buoy out of clutter that would bury it on an analogue display. The same processing enables scan-to-scan correlation, target trails, and the automatic tracking that underpins ARPA (section 21.6).