Study guide
21.2 Range, Pulse Width & PRF
FCC General Radiotelephone Operator License GROL
Track your progress as you read
Finished sections get a check mark.
1 Introduction & GROL Exam Overview
1.1 About the General Radiotelephone Operator License 1.2 Exam Format, COLEMs, FRN & Application Process
2 Element 1: Rules & Regulations
2.1 Equipment Requirements (Part 80) 2.2 License Requirements & Operator Authority 2.3 Watchkeeping & Logkeeping Duties 2.4 Log Entries & Required Records 2.5 Ship Station Control, Inspections & International Rules
3 Element 1: Communications Procedures
3.1 Bridge-to-Bridge Operations & VTS 3.2 Distress Communications & Alerting 3.3 Operating Procedures, Calling & Testing 3.4 Urgency (PAN PAN) & Safety (SECURITE) Traffic 3.5 The GMDSS Concept & Ship Responsibilities
4 Element 1: Equipment Operations
4.1 VHF Equipment Controls 4.2 MF/HF SSB Equipment Controls 4.3 DSC Operations & Equipment Faults 4.4 VHF Channel Selection & Channel Assignments 4.5 MF/HF Frequency & Emission Selection 4.6 Required Equipment Tests & On-Air Test Procedure
5 Element 1: Other Equipment & Antennas
5.1 Marine Antennas & Polarization 5.2 EPIRBs & Emergency Beacons 5.3 Power Sources, Reserve Power & Required Tests 5.4 Search and Rescue Transponders (SARTs) 5.5 Survival Craft Portable VHF (SCT) Requirements 5.6 NAVTEX & Maritime Safety Information
6 Element 3: Electrical Principles
6.1 Electrical Elements, Units & Power Types 6.2 Magnetism & Magnetic Circuits 6.3 Resistance, Capacitance & Inductance 6.4 Waveforms & Semiconductor Introduction 6.5 Materials, Corrosion & Skin Effect 6.6 AC Measurement & Conversion Factors 6.7 Conduction, Reactive Power & Maximum Power Transfer
7 Element 3: Electrical Math
7.1 Ohm's Law — Series & Parallel Circuits 7.2 Frequency, Period, Wavelength & Waveform Math 7.3 Power Relationships & Decibels 7.4 RC/RL Time Constants 7.5 Frequency Counter Accuracy, PPM & Harmonics 7.6 Impedance in Rectangular & Polar Coordinates 7.7 Regulation, Turns Ratio, Zener Bias & Conductance
8 Element 3: Circuit Components — Passives & Power Devices
8.1 Capacitors & Photoconductive Devices 8.2 Transformers, Voltage Regulators & Zener Diodes 8.3 Diodes, SCRs & Triacs
9 Element 3: Active Components — Transistors & Devices
9.1 Bipolar Junction Transistors 9.2 FETs, LEDs & Specialty Devices 9.3 Device Selection, Ratings & Thermal Design
10 Element 3: Practical Circuits — RLC, Op Amps & Schematics
10.1 R-L-C Resonant Circuits 10.2 Op Amps, PLLs, VCOs & Mixers 10.3 Reading Schematics & Signal Flow
11 Element 3: Digital Logic
11.1 Logic Gates & Boolean Functions 11.2 Flip-Flops & Sequential Elements 11.3 Multivibrators & Timing Circuits 11.4 Microprocessors & Bus Architecture 11.5 TTL Logic Families & Input Voltage Levels 11.6 Positive & Negative Logic and Truth Tables 11.7 Memory Types & Microprocessor Concepts 11.8 Counters, Prescalers, BCD & Data Converters
12 Element 3: Receivers
12.1 Receiver Theory & Superheterodyne Architecture 12.2 RF Amplifiers & Front-End Design 12.3 Filters & Detectors 12.4 Audio, Squelch & Receiver Performance Specs 12.5 Receiver Oscillators: Colpitts, Hartley & Pierce 12.6 Mixing, Image Frequencies & Spurious Products 12.7 IF Selectivity & Filter Bandwidth
13 Element 3: Transmitters
13.1 RF Amplifier Classes & Efficiency 13.2 Oscillators, Modulators & Tuning Networks 13.3 SSB Transmitters & Modern Transmitter Technology
14 Element 3: Signals, Emissions & Modulation
14.1 Amplitude & Frequency Modulation 14.2 Single-Sideband Modulation 14.3 Pulse Modulation & Emission Types
15 Element 3: Power Sources
15.1 Batteries & Energy Storage 15.2 Motors, Generators & Power Supplies
16 Element 3: Antennas & Feed Lines
16.1 Antenna Theory, Types & Patterns 16.2 Voltage, Current & Impedance on Antennas 16.3 Transmission Lines, Velocity Factor & SWR 16.4 Effective Radiated Power & Antenna Bandwidth
17 Element 3 Background: Propagation & Radio Practice
17.1 Radio Wave Propagation Modes 17.2 Multipath, Fading & Doppler Effects 17.3 Radio Practice, Interference & Good Engineering
18 Element 3: Aircraft Radio Navigation Systems
18.1 DME & VOR 18.2 ILS, ADF & ATC Transponders 18.3 Aircraft Antennas, Frequencies & Equipment Functions
19 Element 3: Installation, Maintenance & Repair
19.1 Indicating Meters & Meter Movements 19.2 Oscilloscopes & Waveform Measurement 19.3 Measurement Procedures 19.4 Installation Codes & Bonding Procedures 19.5 Frequency Standards, SINAD Meters & EMI Hunting 19.6 Spectrum Analyzers, TDRs & Service Monitors 19.7 Bench Repair Practices, ESD & Rework Tools 19.8 Systematic Troubleshooting & Field Fault Diagnosis
20 Element 3: Communications Technology & Marine Systems
20.1 Transmission Types, Coding & Multiplexing 20.2 Signal Processing, Software & Codes 20.3 Marine VHF, MF/HF & SSB-SITOR 20.4 Survival Craft Electronics, FAX & NAVTEX 20.5 NMEA 0183 & NMEA 2000 Data Networks
21 Element 3: RADAR & Satellite Systems
21.1 RADAR Theory & Pulse Fundamentals 21.2 Range, Pulse Width & PRF 21.3 Radar Antennas & Waveguides 21.4 INMARSAT Satellite Communications 21.5 RADAR Components: Magnetron, Duplexer, ATR & Synchro 21.6 RADAR Equipment, ARPA & Radiation Safety 21.7 Low Earth Orbit Systems: Iridium & COSPAS-SARSAT 21.8 GPS Satellite Navigation & DGPS
22 Element 3: RF & Electrical Safety
22.1 RF Radiation Exposure Limits 22.2 Electrical Safety Practices for Radio Technicians
23 Study Strategy & Exam Day
23.1 Study Strategy, Practice Plan & Exam Day
21.2 Range, Pulse Width & PRF
Key Takeaways Explain This Topic AI
Range R = c × t / 2; each nautical mile of range corresponds to about 12.346 µs of round-trip delay
Pulse width sets minimum range and range resolution: shorter pulses resolve closer/finer targets; longer pulses put more energy on distant targets
PRF (or PRR) sets maximum unambiguous range: lower PRF → longer wait for late echoes → greater unambiguous range
Long-range scales use wide pulse width and slow PRF; short-range scales use narrow pulse width and fast PRF
- Duty cycle = pulse width × PRF; average power = peak power × duty cycle
- Last updated: August 2026
21.2 Range, Pulse Width & PRF
Quick Answer: Range from time : R = c t / 2 (≈ 12.346 µs/NM ). Short pulse → better range resolution and minimum range ; long pulse → more energy for distant targets. Low PRF → greater maximum unambiguous range ; high PRF → more pulses per scan on short scales. Long range = wide PW + slow PRF ; short range = narrow PW + fast PRF . Duty cycle = PW × PRF .
Key topic 092 is almost pure trade-off reasoning. If you only memorize one sentence for radar timing, make it: long range wants energy and waiting time; short range wants precision and rapid updates.
Range from round-trip time
Electromagnetic energy travels at c ≈ 3 × 10⁸ m/s . For a target at one-way distance R, the pulse travels 2R , so: R = c t 2 R = \frac{c \, t}{2} R = 2 c t
In nautical-mile units used on marine displays: R N M ≈ t μ s 12.346 R_{\mathrm{NM}} \approx \frac{t_{\mu\mathrm{s}}}{12.346} R NM ≈ 12.346 t μ s
- t (round trip) Approx. range
- 12.346 µs 1 NM
- 61.7–62 µs 5 NM
- 123.5 µs 10 NM
The same physics underlies aircraft DME slant-range timing (Topic 3-K)—radar simply uses a passive echo instead of a ground transponder reply.
- Pulse width — minimum range and range resolution
- Minimum range
While the transmitter is on, the receiver is effectively deaf (duplexer isolation, TR firing, recovery time). If a target’s echo returns before the pulse ends and the receiver recovers, that echo is lost or corrupted. Therefore minimum detectable range grows with pulse width (plus recovery). Short-range harbor work demands narrow pulses.
Range resolution
Range resolution is the minimum range separation at which two targets on the same bearing still paint as two echoes: Δ R = c τ 2 \Delta R = \frac{c \, \tau}{2} Δ R = 2 c τ
- Pulse width τ Approx. range resolution
- 0.1 µs 15 m
- 0.25 µs ~37.5 m
- 1.0 µs ~150 m
Two ships 20 m apart in range look like one blob if τ is 0.25 µs, but may split cleanly with a 0.05–0.1 µs pulse. That is why short-range scales auto-select narrow PW.
Energy vs resolution trade-off
Longer pulses deliver more energy (Pt × τ) to the target, improving detection of weak or distant echoes, rain-filled paths, or small RCS objects—at the cost of resolution and minimum range. Shorter pulses do the opposite.
- Parameter primarily improved by… Shorter PW Longer PW
- Range resolution ✓
- Minimum range ✓
- Detecting weak/long-range targets (energy) ✓
- PRF / PRR — maximum unambiguous range
PRF (pulse repetition frequency) or PRR (pulse repetition rate) is the number of pulses transmitted per second . PRI = 1 / PRF is the listening window after each pulse.
Unambiguous range
The radar must receive an echo from a target before it transmits the next pulse—or it cannot tell whether a late return belongs to the latest pulse or an earlier one ( second-time-around / range ambiguity ). R u n a m b = c 2 P R F = c P R I 2 R_{\mathrm{unamb}} = \frac{c}{2 \, \mathrm{PRF}} = \frac{c \, \mathrm{PRI}}{2} R unamb = 2 PRF c = 2 c PRI
- PRF PRI Approx. max unambiguous range
- 2,500 Hz 400 µs ~32 NM (≈ 60 km)
- 2,000 Hz 500 µs ~40 NM
- 1,000 Hz 1,000 µs ~80 NM
- 500 Hz 2,000 µs ~160 NM
Lower PRF → greater maximum unambiguous range. That is the pool relationship in one line. Higher PRF is fine on short scales where all real targets return quickly and you want more hits per antenna scan (smoother paint, better detection probability).
Hits per scan (qualitative)
As the antenna beam sweeps past a target, the number of pulses that “illuminate” it is roughly beamwidth / 360° × PRF / RPM . Higher PRF or slower rotation increases hits per scan—another reason short-range modes run faster PRFs.
Duty cycle and average power
Duty cycle is the fraction of time the transmitter is actually emitting RF: D = τ × P R F = τ P R I D = \tau \times \mathrm{PRF} = \frac{\tau}{\mathrm{PRI}} D = τ × PRF = PRI τ
Average power : P a v g = P p e a k × D = P p e a k × τ × P R F P_{\mathrm{avg}} = P_{\mathrm{peak}} \times D = P_{\mathrm{peak}} \times \tau \times \mathrm{PRF} P avg = P peak × D = P peak × τ × PRF
Worked example (classic numbers): peak power 25 kW , τ = 0.5 µs , PRF = 1,000 Hz : D = 0.5 × 10 − 6 × 1000 = 5 × 10 − 4 = 0.05 % D = 0.5 \times 10^{-6} \times 1000 = 5 \times 10^{-4} = 0.05\% D = 0.5 × 1 0 − 6 × 1000 = 5 × 1 0 − 4 = 0.05% P a v g = 25,000 × 5 × 10 − 4 = 12.5 W P_{\mathrm{avg}} = 25{,}000 \times 5 \times 10^{-4} = \mathbf{12.5\ W} P avg = 25 , 000 × 5 × 1 0 − 4 = 12.5 W
Marine radars are peak-hungry but average-power modest—important for power-supply sizing and for understanding why a “25 kW radar” does not draw 25 kW continuously from the ship’s bus.
Range-scale pairing table (memorize for 092)
Element 3 asks which pulse width and pulse repetition rate pair with common range scales. Pattern: far = wide + slow; near = narrow + fast .
- Range setting Appropriate PW Appropriate PRF (pps) Logic
- 1.5 mile 0.05 µs 2,000 Finest resolution, short listening window OK
- 6 mile 0.25 µs 1,000 Mid short-range compromise
- 25 mile 1.0 µs 500 Energy + long unambiguous wait
- 48 mile 1.0 µs 500 Long-range: wide + slow
- Verbal rules (exact pool wording)
Long ranges: use a wide pulse width and slow repetition rate .
Short ranges: use a narrow pulse width and fast repetition rates .
Wrong combinations to reject on sight:
Wide pulse + fast PRF on long range (wastes unambiguous margin, smears close targets if used short).
Narrow pulse + slow PRF on short range (poor update/hits, not the pool’s “most appropriate”).
Extremely long pulses (e.g., 2.5 µs) paired with high PRF—usually distractors.
Putting the three knobs together
When the operator (or automatic range logic) changes the range scale , the radar typically changes PW and PRF together :
Zoom in (harbor): narrow τ for resolution/min range; high PRF for dense paint; unambiguous range still covers the short scale.
Zoom out (open sea): wide τ for echo energy; low PRF so 48 NM targets return before the next pulse.
Duty cycle may stay in a similar order of magnitude even as τ and PRF move in opposite directions—designers balance average power and magnetron stress.
Qualitative radar equation reminder
Even with perfect PW/PRF choice, detection still needs enough Pr . Peak power, antenna gain, target RCS, and R⁴ loss dominate. A technician chasing “no long-range targets” checks magnetron power, waveguide SWR, antenna height/obstructions, and tune —not only the PRF number on the menu.
Exam-day checklist (3-O 092 + 090 timing)
R = c t / 2 ; NM ≈ t_µs / 12.346 .
PW controls min range and range resolution (ΔR = cτ/2).
PRF controls max unambiguous range (lower PRF → farther unambiguous).
Long range: wide PW + slow PRF; short range: narrow PW + fast PRF.
Memorize table anchors: 1.5 mi → 0.05 µs / 2000 pps ; 6 mi → 0.25 µs / 1000 ; 25–48 mi → 1.0 µs / 500 .
Duty cycle = PW × PRF ; Pavg = Ppeak × D .
Next section moves the pulse from the modulator to space: slotted arrays, waveguides, beamwidth, and SART painting on the PPI .