Study guide

12.7 IF Selectivity & Filter Bandwidth

FCC General Radiotelephone Operator License GROL

Track your progress as you read

Finished sections get a check mark.

1 Introduction & GROL Exam Overview

1.1 About the General Radiotelephone Operator License 1.2 Exam Format, COLEMs, FRN & Application Process

2 Element 1: Rules & Regulations

2.1 Equipment Requirements (Part 80) 2.2 License Requirements & Operator Authority 2.3 Watchkeeping & Logkeeping Duties 2.4 Log Entries & Required Records 2.5 Ship Station Control, Inspections & International Rules

3 Element 1: Communications Procedures

3.1 Bridge-to-Bridge Operations & VTS 3.2 Distress Communications & Alerting 3.3 Operating Procedures, Calling & Testing 3.4 Urgency (PAN PAN) & Safety (SECURITE) Traffic 3.5 The GMDSS Concept & Ship Responsibilities

4 Element 1: Equipment Operations

4.1 VHF Equipment Controls 4.2 MF/HF SSB Equipment Controls 4.3 DSC Operations & Equipment Faults 4.4 VHF Channel Selection & Channel Assignments 4.5 MF/HF Frequency & Emission Selection 4.6 Required Equipment Tests & On-Air Test Procedure

5 Element 1: Other Equipment & Antennas

5.1 Marine Antennas & Polarization 5.2 EPIRBs & Emergency Beacons 5.3 Power Sources, Reserve Power & Required Tests 5.4 Search and Rescue Transponders (SARTs) 5.5 Survival Craft Portable VHF (SCT) Requirements 5.6 NAVTEX & Maritime Safety Information

6 Element 3: Electrical Principles

6.1 Electrical Elements, Units & Power Types 6.2 Magnetism & Magnetic Circuits 6.3 Resistance, Capacitance & Inductance 6.4 Waveforms & Semiconductor Introduction 6.5 Materials, Corrosion & Skin Effect 6.6 AC Measurement & Conversion Factors 6.7 Conduction, Reactive Power & Maximum Power Transfer

7 Element 3: Electrical Math

7.1 Ohm's Law — Series & Parallel Circuits 7.2 Frequency, Period, Wavelength & Waveform Math 7.3 Power Relationships & Decibels 7.4 RC/RL Time Constants 7.5 Frequency Counter Accuracy, PPM & Harmonics 7.6 Impedance in Rectangular & Polar Coordinates 7.7 Regulation, Turns Ratio, Zener Bias & Conductance

8 Element 3: Circuit Components — Passives & Power Devices

8.1 Capacitors & Photoconductive Devices 8.2 Transformers, Voltage Regulators & Zener Diodes 8.3 Diodes, SCRs & Triacs

9 Element 3: Active Components — Transistors & Devices

9.1 Bipolar Junction Transistors 9.2 FETs, LEDs & Specialty Devices 9.3 Device Selection, Ratings & Thermal Design

10 Element 3: Practical Circuits — RLC, Op Amps & Schematics

10.1 R-L-C Resonant Circuits 10.2 Op Amps, PLLs, VCOs & Mixers 10.3 Reading Schematics & Signal Flow

11 Element 3: Digital Logic

11.1 Logic Gates & Boolean Functions 11.2 Flip-Flops & Sequential Elements 11.3 Multivibrators & Timing Circuits 11.4 Microprocessors & Bus Architecture 11.5 TTL Logic Families & Input Voltage Levels 11.6 Positive & Negative Logic and Truth Tables 11.7 Memory Types & Microprocessor Concepts 11.8 Counters, Prescalers, BCD & Data Converters

12 Element 3: Receivers

12.1 Receiver Theory & Superheterodyne Architecture 12.2 RF Amplifiers & Front-End Design 12.3 Filters & Detectors 12.4 Audio, Squelch & Receiver Performance Specs 12.5 Receiver Oscillators: Colpitts, Hartley & Pierce 12.6 Mixing, Image Frequencies & Spurious Products 12.7 IF Selectivity & Filter Bandwidth

13 Element 3: Transmitters

13.1 RF Amplifier Classes & Efficiency 13.2 Oscillators, Modulators & Tuning Networks 13.3 SSB Transmitters & Modern Transmitter Technology

14 Element 3: Signals, Emissions & Modulation

14.1 Amplitude & Frequency Modulation 14.2 Single-Sideband Modulation 14.3 Pulse Modulation & Emission Types

15 Element 3: Power Sources

15.1 Batteries & Energy Storage 15.2 Motors, Generators & Power Supplies

16 Element 3: Antennas & Feed Lines

16.1 Antenna Theory, Types & Patterns 16.2 Voltage, Current & Impedance on Antennas 16.3 Transmission Lines, Velocity Factor & SWR 16.4 Effective Radiated Power & Antenna Bandwidth

17 Element 3 Background: Propagation & Radio Practice

17.1 Radio Wave Propagation Modes 17.2 Multipath, Fading & Doppler Effects 17.3 Radio Practice, Interference & Good Engineering

18 Element 3: Aircraft Radio Navigation Systems

18.1 DME & VOR 18.2 ILS, ADF & ATC Transponders 18.3 Aircraft Antennas, Frequencies & Equipment Functions

19 Element 3: Installation, Maintenance & Repair

19.1 Indicating Meters & Meter Movements 19.2 Oscilloscopes & Waveform Measurement 19.3 Measurement Procedures 19.4 Installation Codes & Bonding Procedures 19.5 Frequency Standards, SINAD Meters & EMI Hunting 19.6 Spectrum Analyzers, TDRs & Service Monitors 19.7 Bench Repair Practices, ESD & Rework Tools 19.8 Systematic Troubleshooting & Field Fault Diagnosis

20 Element 3: Communications Technology & Marine Systems

20.1 Transmission Types, Coding & Multiplexing 20.2 Signal Processing, Software & Codes 20.3 Marine VHF, MF/HF & SSB-SITOR 20.4 Survival Craft Electronics, FAX & NAVTEX 20.5 NMEA 0183 & NMEA 2000 Data Networks

21 Element 3: RADAR & Satellite Systems

21.1 RADAR Theory & Pulse Fundamentals 21.2 Range, Pulse Width & PRF 21.3 Radar Antennas & Waveguides 21.4 INMARSAT Satellite Communications 21.5 RADAR Components: Magnetron, Duplexer, ATR & Synchro 21.6 RADAR Equipment, ARPA & Radiation Safety 21.7 Low Earth Orbit Systems: Iridium & COSPAS-SARSAT 21.8 GPS Satellite Navigation & DGPS

22 Element 3: RF & Electrical Safety

22.1 RF Radiation Exposure Limits 22.2 Electrical Safety Practices for Radio Technicians

23 Study Strategy & Exam Day

23.1 Study Strategy, Practice Plan & Exam Day

12.7 IF Selectivity & Filter Bandwidth

Key Takeaways Explain This Topic AI

A receiver IF filter bandwidth should be slightly greater than the bandwidth of the received signal

2.4 kHz IF selectivity is optimum for SSB voice signals

10 kHz IF selectivity is optimum for double-sideband AM

15 kHz IF selectivity is desirable for a wideband FM phone receiver

  • Too wide an IF filter lets undesired signals reach the audio stage; SAW filters suit micro-miniature circuits
  • Last updated: August 2026

12.7 IF Selectivity & Filter Bandwidth

Quick Answer: IF bandwidth should be slightly greater than the received-signal bandwidth . SSB voice → 2.4 kHz. Double-sideband AM → 10 kHz. Wideband FM phone → 15 kHz. Too wide and undesired signals reach the audio stage . SAW filters suit micro-miniature circuits.

Sub-topic 3-F-045 is three numbers and one principle. Because the numbers map directly onto the modulation types in chapter 14, learning them here pays twice.

The matching principle

How should the filter bandwidth of a receiver IF section compare with the bandwidth of a received signal? Slightly greater than the received-signal bandwidth.

Not equal, not much greater — slightly greater . The reasoning cuts both ways:

  • Filter too narrow Filter too wide
  • Clips the edges of the wanted signal Undesired signals reach the audio stage
  • Muffled, distorted audio Adjacent-channel interference audible
  • FM signals distort badly as deviation peaks are cut Noise floor rises — bandwidth admits noise power
  • Reduced effective sensitivity

The margin exists because a real signal is never perfectly centred. Transmitter frequency error, receiver oscillator drift, and Doppler shift on a moving vessel all displace the signal slightly within the passband. A filter exactly as wide as the signal would clip whichever edge drifted outward.

What is an undesirable effect of using too wide a filter bandwidth in the IF section of a receiver? Undesired signals will reach the audio stage. That is the pool's phrasing, and it is worth noting the mechanism: a wide filter does not merely add noise, it lets adjacent-channel transmissions through to be demodulated alongside the one you want.

The three numbers

  • Signal type Optimum IF selectivity Why
  • SSB voice 2.4 kHz One sideband only, carrying roughly 300–2700 Hz of speech — no carrier, no second sideband
  • Double-sideband AM 10 kHz Carrier plus two sidebands: a 5 kHz audio bandwidth becomes 10 kHz of RF
  • Wideband FM phone 15 kHz Carson's rule on a narrowband-FM voice channel with ±5 kHz deviation

These are asked in both directions — " a receiver selectivity of 2.4 kHz is optimum for what type of signals? " as well as " what selectivity is desirable for a wideband FM phone receiver? " — so learn the pairing, not just the list.

Where the numbers come from

SSB — 2.4 kHz. Suppressing the carrier and one sideband is the whole point of SSB (section 14.2). What remains is a single translated copy of the speech band, roughly 2.4 kHz wide. This is why SSB is so spectrum-efficient, and why a 2.4 kHz filter in an SSB receiver is doing exactly the right job.

AM — 10 kHz. In double-sideband AM the transmitted bandwidth is twice the highest audio frequency. Feed 5 kHz of audio in and you occupy 10 kHz of RF, symmetric about the carrier. Note the relationship to SSB: AM needs roughly four times the bandwidth of SSB for the same audio, because it carries two sidebands instead of one.

FM — 15 kHz. For frequency modulation, Carson's rule estimates bandwidth as 2 × (deviation + highest modulating frequency) . A marine or land-mobile channel with ±5 kHz deviation and 3 kHz audio gives 2 × (5 + 3) = 16 kHz , which the pool rounds to the standard 15 kHz IF figure. Recall from section 20.3 that ±5 kHz is exactly the maximum allowable deviation for VHF marine radios — the numbers are consistent across the pool.

Filter technologies

Which one of these filters can be used in micro-miniature electronic circuits? Receiver SAW IF filter.

A SAW (Surface Acoustic Wave) filter launches an acoustic wave across a piezoelectric substrate between interdigitated metal transducers. Because acoustic waves travel roughly 100,000 times slower than electromagnetic ones, the structure that would need metres of transmission line becomes millimetres of chip.

  • Filter type Typical use Size
  • SAW Micro-miniature circuits , IF filtering in handhelds — the pool's answer Chip-scale
  • Crystal / monolithic crystal Narrow SSB and CW filters, high Q Small module
  • Ceramic Consumer FM/AM IF stages Small
  • LC Wideband IF, general purpose Larger
  • Mechanical Very sharp HF-band IF filters (older designs) Bulky

Practical note: filter characteristics live in the shape factor — the ratio of the −60 dB bandwidth to the −6 dB bandwidth. A shape factor near 1 approaches a brick wall; a value of 3 or more means skirts so gentle that a strong adjacent signal still gets through even though the nominal bandwidth looks correct. Two filters both specified at "2.4 kHz" can perform very differently for this reason.

On the bench

A receiver that sounds muffled and lacks highs on SSB, or that distorts on FM, is a candidate for a too-narrow or misaligned IF. A receiver that is noisy and picks up the channel next door has an IF that is too wide — or a filter that has been bypassed or damaged. Because the IF filter fixes the receiver's fundamental selectivity, no amount of audio filtering downstream can recover what a wrong IF bandwidth has already let through.