Study guide

12.6 Mixing, Image Frequencies & Spurious Products

FCC General Radiotelephone Operator License GROL

Track your progress as you read

Finished sections get a check mark.

1 Introduction & GROL Exam Overview

1.1 About the General Radiotelephone Operator License 1.2 Exam Format, COLEMs, FRN & Application Process

2 Element 1: Rules & Regulations

2.1 Equipment Requirements (Part 80) 2.2 License Requirements & Operator Authority 2.3 Watchkeeping & Logkeeping Duties 2.4 Log Entries & Required Records 2.5 Ship Station Control, Inspections & International Rules

3 Element 1: Communications Procedures

3.1 Bridge-to-Bridge Operations & VTS 3.2 Distress Communications & Alerting 3.3 Operating Procedures, Calling & Testing 3.4 Urgency (PAN PAN) & Safety (SECURITE) Traffic 3.5 The GMDSS Concept & Ship Responsibilities

4 Element 1: Equipment Operations

4.1 VHF Equipment Controls 4.2 MF/HF SSB Equipment Controls 4.3 DSC Operations & Equipment Faults 4.4 VHF Channel Selection & Channel Assignments 4.5 MF/HF Frequency & Emission Selection 4.6 Required Equipment Tests & On-Air Test Procedure

5 Element 1: Other Equipment & Antennas

5.1 Marine Antennas & Polarization 5.2 EPIRBs & Emergency Beacons 5.3 Power Sources, Reserve Power & Required Tests 5.4 Search and Rescue Transponders (SARTs) 5.5 Survival Craft Portable VHF (SCT) Requirements 5.6 NAVTEX & Maritime Safety Information

6 Element 3: Electrical Principles

6.1 Electrical Elements, Units & Power Types 6.2 Magnetism & Magnetic Circuits 6.3 Resistance, Capacitance & Inductance 6.4 Waveforms & Semiconductor Introduction 6.5 Materials, Corrosion & Skin Effect 6.6 AC Measurement & Conversion Factors 6.7 Conduction, Reactive Power & Maximum Power Transfer

7 Element 3: Electrical Math

7.1 Ohm's Law — Series & Parallel Circuits 7.2 Frequency, Period, Wavelength & Waveform Math 7.3 Power Relationships & Decibels 7.4 RC/RL Time Constants 7.5 Frequency Counter Accuracy, PPM & Harmonics 7.6 Impedance in Rectangular & Polar Coordinates 7.7 Regulation, Turns Ratio, Zener Bias & Conductance

8 Element 3: Circuit Components — Passives & Power Devices

8.1 Capacitors & Photoconductive Devices 8.2 Transformers, Voltage Regulators & Zener Diodes 8.3 Diodes, SCRs & Triacs

9 Element 3: Active Components — Transistors & Devices

9.1 Bipolar Junction Transistors 9.2 FETs, LEDs & Specialty Devices 9.3 Device Selection, Ratings & Thermal Design

10 Element 3: Practical Circuits — RLC, Op Amps & Schematics

10.1 R-L-C Resonant Circuits 10.2 Op Amps, PLLs, VCOs & Mixers 10.3 Reading Schematics & Signal Flow

11 Element 3: Digital Logic

11.1 Logic Gates & Boolean Functions 11.2 Flip-Flops & Sequential Elements 11.3 Multivibrators & Timing Circuits 11.4 Microprocessors & Bus Architecture 11.5 TTL Logic Families & Input Voltage Levels 11.6 Positive & Negative Logic and Truth Tables 11.7 Memory Types & Microprocessor Concepts 11.8 Counters, Prescalers, BCD & Data Converters

12 Element 3: Receivers

12.1 Receiver Theory & Superheterodyne Architecture 12.2 RF Amplifiers & Front-End Design 12.3 Filters & Detectors 12.4 Audio, Squelch & Receiver Performance Specs 12.5 Receiver Oscillators: Colpitts, Hartley & Pierce 12.6 Mixing, Image Frequencies & Spurious Products 12.7 IF Selectivity & Filter Bandwidth

13 Element 3: Transmitters

13.1 RF Amplifier Classes & Efficiency 13.2 Oscillators, Modulators & Tuning Networks 13.3 SSB Transmitters & Modern Transmitter Technology

14 Element 3: Signals, Emissions & Modulation

14.1 Amplitude & Frequency Modulation 14.2 Single-Sideband Modulation 14.3 Pulse Modulation & Emission Types

15 Element 3: Power Sources

15.1 Batteries & Energy Storage 15.2 Motors, Generators & Power Supplies

16 Element 3: Antennas & Feed Lines

16.1 Antenna Theory, Types & Patterns 16.2 Voltage, Current & Impedance on Antennas 16.3 Transmission Lines, Velocity Factor & SWR 16.4 Effective Radiated Power & Antenna Bandwidth

17 Element 3 Background: Propagation & Radio Practice

17.1 Radio Wave Propagation Modes 17.2 Multipath, Fading & Doppler Effects 17.3 Radio Practice, Interference & Good Engineering

18 Element 3: Aircraft Radio Navigation Systems

18.1 DME & VOR 18.2 ILS, ADF & ATC Transponders 18.3 Aircraft Antennas, Frequencies & Equipment Functions

19 Element 3: Installation, Maintenance & Repair

19.1 Indicating Meters & Meter Movements 19.2 Oscilloscopes & Waveform Measurement 19.3 Measurement Procedures 19.4 Installation Codes & Bonding Procedures 19.5 Frequency Standards, SINAD Meters & EMI Hunting 19.6 Spectrum Analyzers, TDRs & Service Monitors 19.7 Bench Repair Practices, ESD & Rework Tools 19.8 Systematic Troubleshooting & Field Fault Diagnosis

20 Element 3: Communications Technology & Marine Systems

20.1 Transmission Types, Coding & Multiplexing 20.2 Signal Processing, Software & Codes 20.3 Marine VHF, MF/HF & SSB-SITOR 20.4 Survival Craft Electronics, FAX & NAVTEX 20.5 NMEA 0183 & NMEA 2000 Data Networks

21 Element 3: RADAR & Satellite Systems

21.1 RADAR Theory & Pulse Fundamentals 21.2 Range, Pulse Width & PRF 21.3 Radar Antennas & Waveguides 21.4 INMARSAT Satellite Communications 21.5 RADAR Components: Magnetron, Duplexer, ATR & Synchro 21.6 RADAR Equipment, ARPA & Radiation Safety 21.7 Low Earth Orbit Systems: Iridium & COSPAS-SARSAT 21.8 GPS Satellite Navigation & DGPS

22 Element 3: RF & Electrical Safety

22.1 RF Radiation Exposure Limits 22.2 Electrical Safety Practices for Radio Technicians

23 Study Strategy & Exam Day

23.1 Study Strategy, Practice Plan & Exam Day

12.6 Mixing, Image Frequencies & Spurious Products

Key Takeaways Explain This Topic AI

Mixing is the combination of two signals to produce sum and difference frequencies

The principal frequencies at a mixer output are the two original frequencies plus their sum and their difference

The image frequency is rejected in the RF stage, before the mixer, because after mixing it is indistinguishable from the wanted signal

With a 151.000 MHz channel, an 11.000 MHz IF and a 140.000 MHz local oscillator, the image frequency is 129.000 MHz

  • Overdriving a mixer with excessive signal energy generates spurious mixer products
  • Last updated: August 2026

12.6 Mixing, Image Frequencies & Spurious Products

Quick Answer: Mixing is the combination of two signals to produce sum and difference frequencies . A mixer's output holds the original frequencies plus the sum and the difference . The image is rejected in the RF stage . Image = LO ∓ IF on the opposite side of the LO from the wanted signal: 151 MHz signal, 140 MHz LO, 11 MHz IF → image 129 MHz . Overdriving a mixer generates spurious mixer products .

Sub-topic 3-F-044 (Mixers) contains the single most calculation-heavy idea in the Receivers topic. Get the image-frequency geometry straight and four of its six items fall out.

What mixing does

What is the mixing process in a radio receiver? The combination of two signals to produce sum and difference frequencies.

A mixer is a non-linear device fed two signals — the incoming RF and the local oscillator. Non-linearity is essential: a perfectly linear stage would simply add the two waveforms and produce no new frequencies at all. The non-linear transfer characteristic multiplies them, and multiplication of two sinusoids produces their sum and difference.

What are the principal frequencies that appear at the output of a mixer circuit? The original frequencies and the sum and difference frequencies.

Four components, and the pool's answer names all four:

  • Component Example: RF = 200 MHz, LO = 150 MHz
  • Original RF 200 MHz
  • Original LO 150 MHz
  • Sum (RF + LO) 350 MHz
  • Difference (RF − LO) 50 MHz

The pool asks this concretely — "RF input to a mixer is 200 MHz and the local oscillator frequency is 150 MHz. What output would you expect at the IF output prior to any filtering?" — and the keyed answer is 50, 150, 200 and 350 MHz . All four, because the question says prior to any filtering . The IF filter then selects the one you want, normally the difference.

The image frequency

This is the concept that separates candidates who memorised from candidates who understood.

A mixer produces the IF from any input that differs from the LO by the IF amount — and there are always two such inputs, one above the LO and one below it. One is your wanted signal; the other is the image .

  • Image = wanted signal − 2 × IF (when the LO is below the signal)
  • Equivalently: image = LO − IF when the wanted signal is LO + IF
  • The pool's worked example

Normal channel 151.000 MHz, IF 11.000 MHz, LO 140.000 MHz. What is the image frequency? 129.000 MHz.

Lay it out on a line:

  • Frequency Role Distance from LO
  • 129.000 MHz Image 11 MHz below LO
  • 140.000 MHz Local oscillator —
  • 151.000 MHz Wanted signal 11 MHz above LO

Both 151 and 129 differ from the 140 MHz LO by exactly 11 MHz, so both produce an 11 MHz IF. The mixer cannot tell them apart. Check by subtraction: 151 − 129 = 22 = 2 × IF , which is always the spacing between a signal and its image.

The second pool example

"If a receiver mixes a 13.8 MHz VFO with a 14.255 MHz receive signal to produce a 455 kHz IF, what type of interference will a 13.345 MHz signal produce?" → an image response.

Verify: 14.255 − 13.8 = 0.455 MHz ✓. And 13.8 − 13.345 = 0.455 MHz ✓. Both land on the 455 kHz IF, and 14.255 − 13.345 = 0.910 MHz = 2 × 455 kHz . Textbook image.

Where the image must be rejected

In what radio stage is the image frequency normally rejected? The RF stage.

This is forced by logic, not by convention. Once mixing has happened, the image and the wanted signal occupy exactly the same IF frequency. No IF filter, however sharp, can separate them — they are literally the same frequency by then. The only opportunity is before the mixer, in the tuned RF amplifier and preselector , which is 22 MHz away from the wanted signal in the first example and must roll off enough over that span.

Three consequences worth knowing:

A higher IF improves image rejection , because the image moves further from the wanted signal (2 × IF away) and the RF selectivity has an easier job.

A lower IF improves adjacent-channel selectivity , because sharp narrow filters are easier to build at low frequencies.

Those two pull in opposite directions, which is exactly why double-conversion receivers exist: a high first IF for image rejection, then a low second IF for selectivity (section 12.1).

Overdriving the mixer

What might occur in a receiver if excessive amounts of signal energy overdrive the mixer circuit? Spurious mixer products are generated.

A mixer is deliberately non-linear, but only in a controlled way. Drive it too hard — a strong local transmitter, a nearby broadcast station, too much RF gain — and higher-order products appear: 2RF ± LO , RF ± 2LO , 3RF ± 2LO and beyond. These land on frequencies unrelated to anything you intended, producing "phantom" signals that appear and disappear as the offending transmitter keys.

The practical fixes are the ones the pool implies elsewhere: back off the RF gain , insert attenuation ahead of the receiver, or add a preselector filter. This is also the reason a receiver's intermodulation and blocking specifications matter as much as its sensitivity (section 12.4) — on a ship's mast or an airport ramp, the noise floor is rarely the limiting factor; strong nearby transmitters are.