Study guide

12.3 Multiple Reactions, Catalysis, and Heterogeneous Kinetics

NCEES Fundamentals of Engineering FE

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Mathematics

1.1 Analytic Geometry, Algebra, and Trigonometry 1.2 Calculus and Differential Equations 1.3 Numerical Methods and Measurement Error

2 Chapter 2: Probability and Statistics

2.1 Probability Distributions, Central Tendency, and Regression 2.2 Hypothesis Testing, ANOVA, and Statistical Quality Control

3 Chapter 3: Engineering Sciences

3.1 Mechanics and Dynamics 3.2 Electrical Circuits and Laws

4 Chapter 4: Materials Science

4.1 Material Properties and Compatibilities 4.2 Corrosion, Polymers, Ceramics, and Composites

5 Chapter 5: Chemistry and Biology

5.1 Stoichiometry, Analytical Chemistry, and Chemical Equilibrium 5.2 Organic Chemistry and Nomenclature 5.3 Biological Systems and Kinetics

6 Chapter 6: Fluid Mechanics and Dynamics

6.1 Fluid Properties, Dimensionless Numbers, and Flow Regimes 6.2 Bernoulli Equation and Mechanical Energy Balances 6.3 Flow Measurement and Fluid Machinery 6.4 Compressible and Non-Newtonian Flows

7 Chapter 7: Thermodynamics

7.1 Thermodynamic Properties, Ideal Gas, and State Equations 7.2 Laws of Thermodynamics and Cyclic Processes 7.3 Vapor-Liquid Equilibrium (VLE) and Phase Equilibrium 7.4 Chemical Equilibrium, Heats of Reaction, and Mixing

8 Chapter 8: Material and Energy Balances

8.1 Steady-State Material Balances 8.2 Unsteady-State Mass Balances 8.3 Steady-State Energy Balances 8.4 Unsteady-State Energy Balances

9 Chapter 9: Heat Transfer

9.1 Conduction, Convection, and Radiation Fundamentals 9.2 Heat Transfer Coefficients, Fouling, and Overall U 9.3 Heat Exchanger Design

10 Chapter 10: Mass Transfer and Separation

10.1 Diffusion Fundamentals 10.2 Gas Absorption, Stripping, and Liquid-Liquid Extraction 10.3 Distillation and McCabe-Thiele Method 10.4 Continuous Contact Methods, Membrane Separations, and Evaporative Operations

11 Chapter 11: Solids Handling

11.1 Particle Properties and Solid Processing 11.2 Solids Transportation and Storage

12 Chapter 12: Chemical Reaction Engineering

12.1 Reaction Kinetics and Performance Metrics 12.2 Ideal Reactor Design 12.3 Multiple Reactions, Catalysis, and Heterogeneous Kinetics

13 Chapter 13: Economics

13.1 Time Value of Money and Project Selection 13.2 Profitability Analysis, Depreciation, and Break-Even

14 Chapter 14: Process Design

14.1 Process Flowsheets and Instrumentation 14.2 Equipment Selection, Sizing, and Cost Estimation 14.3 Process Optimization, Sustainability, and Inherently Safer Design

15 Chapter 15: Process Control

15.1 Process Dynamics and Transfer Functions 15.2 Feedback Control Loops, PID Tuning, and Control Hardware

16 Chapter 16: Safety, Health, and Environment

16.1 Flammability, Toxicity, and Industrial Hygiene 16.2 Hazard Identification and Risk Analysis 16.3 Overpressure Relief, Reactivity Hazards, and Waste Regulations

17 Chapter 17: Ethics and Professional Practice

17.1 Professional Codes of Ethics and Public Welfare 17.2 Intellectual Property, Contracts, and Professional Liability

12.3 Multiple Reactions, Catalysis, and Heterogeneous Kinetics

Key Takeaways Explain This Topic AI

Parallel reaction selectivity is optimized by reactor choice: high concentration (PFR/Batch) for higher-order desired reactions; low concentration (CSTR) for lower-order desired reactions.

Series reaction yield of the intermediate product is maximized in PFR or Batch reactors due to the absence of back-mixing.

Heterogeneous catalytic rates are defined per unit mass of catalyst, and the Packed Bed Reactor (PBR) equation sizes the catalyst weight W.

The catalytic cycle involves seven sequential steps: external diffusion, internal diffusion, adsorption, surface reaction, desorption, internal diffusion, and external diffusion.

The Thiele modulus compares reaction and pore diffusion rates; the effectiveness factor measures catalyst active site utilization.

Last updated: July 2026

In industrial chemical processes, reactions rarely occur in isolation. Multiple reactions (occurring in series or parallel) are the norm, and catalysts are widely used to accelerate rates and steer selectivity. On the FE Chemical exam, you must understand how to select and operate reactors to maximize selectivity for multiple reactions, identify the steps in heterogeneous catalytic systems, apply packed bed design equations, and analyze mass transfer limitations using the Thiele modulus and effectiveness factor.

Multiple Reactions and Reactor Selectivity

When multiple reactions occur, the primary objective is to maximize the formation of the desired product ( D D D ) while minimizing the undesired product ( U U U ).

1. Parallel Reactions

Consider the competing parallel reactions: Reaction 1 (Desired): A → k 1 D ( − r A1 = r D = k 1 C A a 1 ) \text{Reaction 1 (Desired): } \text{A} \xrightarrow{k_1} \text{D} \quad (-r_{\text{A1}} = r_{\text{D}} = k_1 C_{\text{A}}^{a_1}) Reaction 1 (Desired): A k 1 ​ ​ D ( − r A1 ​ = r D ​ = k 1 ​ C A a 1 ​ ​ ) Reaction 2 (Undesired): A → k 2 U ( − r A2 = r U = k 2 C A a 2 ) \text{Reaction 2 (Undesired): } \text{A} \xrightarrow{k_2} \text{U} \quad (-r_{\text{A2}} = r_{\text{U}} = k_2 C_{\text{A}}^{a_2}) Reaction 2 (Undesired): A k 2 ​ ​ U ( − r A2 ​ = r U ​ = k 2 ​ C A a 2 ​ ​ )

The instantaneous selectivity of desired product D with respect to undesired product U is: S D/U = r D r U = k 1 k 2 C A a 1 − a 2 S_{\text{D/U}} = \frac{r_{\text{D}}}{r_{\text{U}}} = \frac{k_1}{k_2} C_{\text{A}}^{a_1 - a_2} S D/U ​ = r U ​ r D ​ ​ = k 2 ​ k 1 ​ ​ C A a 1 ​ − a 2 ​ ​

To maximize this selectivity, the concentration of reactant A ( C A C_{\text{A}} C A ​ ) must be controlled:

If a 1 > a 2 a_1 > a_2 a 1 ​ > a 2 ​ : The exponent ( a 1 − a 2 ) (a_1 - a_2) ( a 1 ​ − a 2 ​ ) is positive. To maximize selectivity, we must keep C A C_{\text{A}} C A ​ as high as possible. This is achieved by using a Plug Flow Reactor (PFR) or a Batch Reactor , where reactant concentration starts high and decreases gradually, rather than a CSTR. Feeding reactants without diluents also helps.

If a 1 < a 2 a_1 < a_2 a 1 ​ < a 2 ​ : The exponent ( a 1 − a 2 ) (a_1 - a_2) ( a 1 ​ − a 2 ​ ) is negative. To maximize selectivity, we must keep C A C_{\text{A}} C A ​ as low as possible. This is achieved by using a Continuous Stirred Tank Reactor (CSTR) , which operates entirely at the low exit concentration, or by diluting the feed.

2. Series Reactions

Consider series reactions where the desired product is the intermediate, R: A → k 1 R → k 2 S \text{A} \xrightarrow{k_1} \text{R} \xrightarrow{k_2} \text{S} A k 1 ​ ​ R k 2 ​ ​ S

Reactant A is converted to the desired product R, which then reacts to form the undesired waste product S.

The concentration of R reaches a maximum at a specific time (in a batch reactor) or space time (in a flow reactor).

Because a CSTR exhibits back-mixing (where exiting fluid is mixed with incoming reactant, and some fluid leaves immediately while some remains for a long time), the maximum concentration of the intermediate R is significantly lower in a CSTR than in a PFR. Therefore, a PFR or Batch Reactor is preferred to maximize the yield of the intermediate R.

Homogeneous vs. Heterogeneous Kinetics and Catalysis

Homogeneous reactions take place in a single phase, and their rates are based on reactor fluid volume.

Heterogeneous reactions involve more than one phase, most commonly a fluid reactant reacting on the surface of a solid catalyst. In these systems, the reaction rate is defined relative to the mass of the catalyst ( W W W ) rather than fluid volume: − r A ′ = − 1 W d N A d t -r_{\text{A}}' = -\frac{1}{W} \frac{dN_{\text{A}}}{dt} − r A ′ ​ = − W 1 ​ d t d N A ​ ​ where − r A ′ -r_{\text{A}}' − r A ′ ​ has units of mol / ( g cat ⋅ s ) \text{mol}/(\text{g}_{\text{cat}}\cdot\text{s}) mol / ( g cat ​ ⋅ s ) or mol / ( kg cat ⋅ s ) \text{mol}/(\text{kg}_{\text{cat}}\cdot\text{s}) mol / ( kg cat ​ ⋅ s ) .

Packed Bed Reactor (PBR) Design Equation

For a PBR (also called a fixed-bed catalytic reactor), the catalyst is packed inside tubes. The design equation relates the mass of catalyst W W W required to achieve a target conversion X A X_{\text{A}} X A ​ : W = F A 0 ∫ 0 X A d X A − r A ′ W = F_{\text{A}0} \int_0^{X_{\text{A}}} \frac{dX_{\text{A}}}{-r_{\text{A}}'} W = F A 0 ​ ∫ 0 X A ​ ​ − r A ′ ​ d X A ​ ​

This is the heterogeneous analog of the PFR volume design equation.

Steps in a Heterogeneous Catalytic Reaction

For a catalytic reaction to occur on a solid catalyst, reactants must transport from the bulk fluid to the active sites inside the catalyst pores, react, and then the products must transport back. The process consists of seven sequential steps:

External diffusion of reactants from the bulk fluid phase to the external surface of the catalyst pellet.

Internal diffusion of reactants through the catalyst pores to the active sites.

Adsorption of reactants onto the catalyst active sites (often modeled by Langmuir adsorption isotherms).

Surface reaction of adsorbed species to form adsorbed products.

Desorption of products from the active sites.

Internal diffusion of products out of the pores to the external surface.

External diffusion of products from the external surface back into the bulk fluid phase.

If any of these steps is significantly slower than the others, it becomes the Rate-Limiting Step (RLS) .

Mass Transfer Limitations: Thiele Modulus and Effectiveness Factor

Pore diffusion and external mass transfer can severely limit the overall reaction rate, making the catalyst under-utilized.

1. The Thiele Modulus ( ϕ \phi ϕ )

The Thiele modulus is a dimensionless number that represents the ratio of the intrinsic surface reaction rate to the rate of internal diffusion through the catalyst pores. For a first-order reaction in a flat plate or spherical catalyst pellet: ϕ = L k D e \phi = L \sqrt{\frac{k}{D_e}} ϕ = L D e ​ k ​ ​

where:

L L L is the characteristic length of the catalyst pellet (volume of pellet divided by external surface area; for a sphere, L = R p / 3 L = R_p / 3 L = R p ​ /3 ).

k k k is the intrinsic first-order reaction rate constant (based on pellet volume).

D e D_e D e ​ is the effective diffusivity of the reactant inside the pores.

2. The Internal Effectiveness Factor ( η \eta η )

The internal effectiveness factor η \eta η is defined as the ratio of the actual overall reaction rate to the rate that would be achieved if the entire interior of the pellet were exposed to the reactant concentration and temperature at the external pellet surface: η = Actual Reaction Rate Reaction Rate at Surface Conditions \eta = \frac{\text{Actual Reaction Rate}}{\text{Reaction Rate at Surface Conditions}} η = Reaction Rate at Surface Conditions Actual Reaction Rate ​

For isothermal systems, η \eta η is related to the Thiele modulus:

Reaction-Controlled Regime ( ϕ < 1 \phi < 1 ϕ < 1 ): When diffusion is very fast compared to reaction, ϕ \phi ϕ is small and η ≈ 1 \eta \approx 1 η ≈ 1 . The reactant concentration is uniform throughout the pellet, and the catalyst is fully utilized.

Diffusion-Controlled Regime ( ϕ > 3 \phi > 3 ϕ > 3 or large): When diffusion is slow compared to reaction, ϕ \phi ϕ is large and η ≈ 1 / ϕ \eta \approx 1/\phi η ≈ 1/ ϕ . The reactant is consumed near the external surface of the pellet, leaving the interior of the catalyst unutilized.

Worked Example: Packed Bed Reactor Design

Problem: A second-order heterogeneous catalytic reaction A → B \text{A} \rightarrow \text{B} A → B is carried out in a Packed Bed Reactor (PBR). The rate law is − r A ′ = k ′ C A 2 -r_{\text{A}}' = k' C_{\text{A}}^2 − r A ′ ​ = k ′ C A 2 ​ , where k ′ = 0.15 L 2 / ( mol ⋅ g cat ⋅ min ) k' = 0.15\text{ L}^2/(\text{mol}\cdot\text{g}_{\text{cat}}\cdot\text{min}) k ′ = 0.15 L 2 / ( mol ⋅ g cat ​ ⋅ min ) . The feed is a liquid mixture entering at a volumetric flow rate v 0 = 5 L/min v_0 = 5\text{ L/min} v 0 ​ = 5 L/min with an inlet concentration C A 0 = 1.0 mol/L C_{\text{A}0} = 1.0\text{ mol/L} C A 0 ​ = 1.0 mol/L . Calculate the mass of catalyst W W W (in grams) required to achieve 75 % 75\% 75% conversion ( X A = 0.75 X_{\text{A}} = 0.75 X A ​ = 0.75 ). Assume no pressure drop and constant density.

Solution:

State the parameters:

  • v 0 = 5 L/min v_0 = 5\text{ L/min} v 0 ​ = 5 L/min
  • C A 0 = 1.0 mol/L C_{\text{A}0} = 1.0\text{ mol/L} C A 0 ​ = 1.0 mol/L

F A 0 = v 0 C A 0 = 5.0 mol/min F_{\text{A}0} = v_0 C_{\text{A}0} = 5.0\text{ mol/min} F A 0 ​ = v 0 ​ C A 0 ​ = 5.0 mol/min

k ′ = 0.15 L 2 / ( mol ⋅ g cat ⋅ min ) k' = 0.15\text{ L}^2/(\text{mol}\cdot\text{g}_{\text{cat}}\cdot\text{min}) k ′ = 0.15 L 2 / ( mol ⋅ g cat ​ ⋅ min )

X A = 0.75 X_{\text{A}} = 0.75 X A ​ = 0.75

Express concentration in terms of conversion (for constant density): C A = C A 0 ( 1 − X A ) C_{\text{A}} = C_{\text{A}0}(1 - X_{\text{A}}) C A ​ = C A 0 ​ ( 1 − X A ​ ) − r A ′ = k ′ C A 2 = k ′ C A 0 2 ( 1 − X A ) 2 -r_{\text{A}}' = k' C_{\text{A}}^2 = k' C_{\text{A}0}^2 (1 - X_{\text{A}})^2 − r A ′ ​ = k ′ C A 2 ​ = k ′ C A 0 2 ​ ( 1 − X A ​ ) 2

Set up the PBR design equation: W = F A 0 ∫ 0 X A d X A k ′ C A 0 2 ( 1 − X A ) 2 = F A 0 k ′ C A 0 2 ∫ 0 X A d X A ( 1 − X A ) 2 W = F_{\text{A}0} \int_0^{X_{\text{A}}} \frac{dX_{\text{A}}}{k' C_{\text{A}0}^2 (1 - X_{\text{A}})^2} = \frac{F_{\text{A}0}}{k' C_{\text{A}0}^2} \int_0^{X_{\text{A}}} \frac{dX_{\text{A}}}{(1 - X_{\text{A}})^2} W = F A 0 ​ ∫ 0 X A ​ ​ k ′ C A 0 2 ​ ( 1 − X A ​ ) 2 d X A ​ ​ = k ′ C A 0 2 ​ F A 0 ​ ​ ∫ 0 X A ​ ​ ( 1 − X A ​ ) 2 d X A ​ ​

Integrate the expression: ∫ 0 X A d X A ( 1 − X A ) 2 = [ 1 1 − X A ] 0 X A = 1 1 − X A − 1 = X A 1 − X A \int_0^{X_{\text{A}}} \frac{dX_{\text{A}}}{(1 - X_{\text{A}})^2} = \left[ \frac{1}{1 - X_{\text{A}}} \right]_0^{X_{\text{A}}} = \frac{1}{1 - X_{\text{A}}} - 1 = \frac{X_{\text{A}}}{1 - X_{\text{A}}} ∫ 0 X A ​ ​ ( 1 − X A ​ ) 2 d X A ​ ​ = [ 1 − X A ​ 1 ​ ] 0 X A ​ ​ = 1 − X A ​ 1 ​ − 1 = 1 − X A ​ X A ​ ​

Substitute the values: W = 5.0 0.15 ⋅ ( 1.0 ) 2 ⋅ ( 0.75 1 − 0.75 ) W = \frac{5.0}{0.15 \cdot (1.0)^2} \cdot \left( \frac{0.75}{1 - 0.75} \right) W = 0.15 ⋅ ( 1.0 ) 2 5.0 ​ ⋅ ( 1 − 0.75 0.75 ​ ) W = 5.0 0.15 ⋅ ( 0.75 0.25 ) = 33.33 ⋅ 3 = 100 g W = \frac{5.0}{0.15} \cdot \left( \frac{0.75}{0.25} \right) = 33.33 \cdot 3 = 100\text{ g} W = 0.15 5.0 ​ ⋅ ( 0.25 0.75 ​ ) = 33.33 ⋅ 3 = 100 g

Thus, 100 g 100\text{ g} 100 g of catalyst is required to achieve the desired conversion of 75 % 75\% 75% .