Study guide
14.1 Process Flowsheets and Instrumentation
NCEES Fundamentals of Engineering FE
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Mathematics
1.1 Analytic Geometry, Algebra, and Trigonometry 1.2 Calculus and Differential Equations 1.3 Numerical Methods and Measurement Error
2 Chapter 2: Probability and Statistics
2.1 Probability Distributions, Central Tendency, and Regression 2.2 Hypothesis Testing, ANOVA, and Statistical Quality Control
3 Chapter 3: Engineering Sciences
3.1 Mechanics and Dynamics 3.2 Electrical Circuits and Laws
4 Chapter 4: Materials Science
4.1 Material Properties and Compatibilities 4.2 Corrosion, Polymers, Ceramics, and Composites
5 Chapter 5: Chemistry and Biology
5.1 Stoichiometry, Analytical Chemistry, and Chemical Equilibrium 5.2 Organic Chemistry and Nomenclature 5.3 Biological Systems and Kinetics
6 Chapter 6: Fluid Mechanics and Dynamics
6.1 Fluid Properties, Dimensionless Numbers, and Flow Regimes 6.2 Bernoulli Equation and Mechanical Energy Balances 6.3 Flow Measurement and Fluid Machinery 6.4 Compressible and Non-Newtonian Flows
7 Chapter 7: Thermodynamics
7.1 Thermodynamic Properties, Ideal Gas, and State Equations 7.2 Laws of Thermodynamics and Cyclic Processes 7.3 Vapor-Liquid Equilibrium (VLE) and Phase Equilibrium 7.4 Chemical Equilibrium, Heats of Reaction, and Mixing
8 Chapter 8: Material and Energy Balances
8.1 Steady-State Material Balances 8.2 Unsteady-State Mass Balances 8.3 Steady-State Energy Balances 8.4 Unsteady-State Energy Balances
9 Chapter 9: Heat Transfer
9.1 Conduction, Convection, and Radiation Fundamentals 9.2 Heat Transfer Coefficients, Fouling, and Overall U 9.3 Heat Exchanger Design
10 Chapter 10: Mass Transfer and Separation
10.1 Diffusion Fundamentals 10.2 Gas Absorption, Stripping, and Liquid-Liquid Extraction 10.3 Distillation and McCabe-Thiele Method 10.4 Continuous Contact Methods, Membrane Separations, and Evaporative Operations
11 Chapter 11: Solids Handling
11.1 Particle Properties and Solid Processing 11.2 Solids Transportation and Storage
12 Chapter 12: Chemical Reaction Engineering
12.1 Reaction Kinetics and Performance Metrics 12.2 Ideal Reactor Design 12.3 Multiple Reactions, Catalysis, and Heterogeneous Kinetics
13 Chapter 13: Economics
13.1 Time Value of Money and Project Selection 13.2 Profitability Analysis, Depreciation, and Break-Even
14 Chapter 14: Process Design
14.1 Process Flowsheets and Instrumentation 14.2 Equipment Selection, Sizing, and Cost Estimation 14.3 Process Optimization, Sustainability, and Inherently Safer Design
15 Chapter 15: Process Control
15.1 Process Dynamics and Transfer Functions 15.2 Feedback Control Loops, PID Tuning, and Control Hardware
16 Chapter 16: Safety, Health, and Environment
16.1 Flammability, Toxicity, and Industrial Hygiene 16.2 Hazard Identification and Risk Analysis 16.3 Overpressure Relief, Reactivity Hazards, and Waste Regulations
17 Chapter 17: Ethics and Professional Practice
17.1 Professional Codes of Ethics and Public Welfare 17.2 Intellectual Property, Contracts, and Professional Liability
14.1 Process Flowsheets and Instrumentation
Key Takeaways Explain This Topic AI
PFDs represent the overall chemical process flow and major equipment with stream tables, while P&IDs show detailed piping, valves, instrumentation, safety devices, and control lines.
The ISA-5.1 standard defines instrumentation bubbles where no line represents field-mounted, a solid horizontal line indicates main panel access, and a square-enclosure denotes shared DCS/PLC systems.
Tag numbers use letter codes where the first letter denotes the measured variable (e.g., F for Flow, T for Temperature) and succeeding letters denote the function (e.g., C for Controller, T for Transmitter).
Different connection lines indicate physical media: solid lines for process piping, dashed lines for electrical signals, double-slashed lines for pneumatic signals, and dotted lines for software links.
Control loop configurations on P&IDs include feedback, feedforward, cascade (nested loops where primary controller sets secondary setpoint), and ratio (maintaining a constant ratio of flow rates).
Last updated: July 2026
Process Flowsheets and Instrumentation
Process design begins with flowsheets that visually represent the chemical process. The level of detail increases as the design progresses, transitioning from block flow diagrams (BFDs) to process flow diagrams (PFDs) and eventually to piping and instrumentation diagrams (P&IDs). For the FE Chemical exam, candidates must be proficient in interpreting these diagrams, understanding instrumentation symbols under the ISA-5.1 standard, and identifying various control loop configurations.
Process Flow Diagrams (PFDs) vs. Piping and Instrumentation Diagrams (P&IDs)
A Process Flow Diagram (PFD) provides a high-level overview of the process. It focuses on the main process path, showing major equipment (reactors, columns, heat exchangers, pumps), process streams, and basic control schemes. PFDs typically include a stream table detailing mass and energy balances, operating temperatures, pressures, and flow rates. PFDs omit utility lines, detailed piping, valve specifications, and safety alarms.
A Piping and Instrumentation Diagram (P&ID) is a highly detailed schematic. It displays the entire physical plant design, including all process and utility piping, valve types and sizes, pipe specifications, insulation, instrumentation, safety devices (such as pressure safety valves (PSVs) and rupture discs), alarms, and connection lines to distributed control systems (DCS). P&IDs do not show physical scales, piping layouts, or stream tables.
Instrumentation Symbols (ISA-5.1)
The Instrument Society of America (ISA) S5.1 standard defines the symbols and letters used for instrumentation. A circular symbol, or bubble, represents an instrument. The lines inside and surrounding the bubble indicate its location and accessibility:
No horizontal line: Field-mounted instrument (located near the physical equipment in the plant).
Single solid horizontal line: Board-mounted or control-room instrument, accessible to the operator at the main control panel.
Double solid horizontal line: Auxiliary control panel, accessible to the operator.
Single dashed horizontal line: Instrument located behind the panel or in an inaccessible location.
Bubble inside a square: Shared display and control (e.g., Distributed Control System (DCS) or Programmable Logic Controller (PLC) interface).
Instrument Tag Numbers and Letter Codes
Each instrument has an alphanumeric tag (e.g., TIC 101). The letters represent the function, and the numbers represent the loop.
First Letter (Measured Variable):
- F: Flow
- T: Temperature
- P: Pressure
- L: Level
- C: Concentration or Composition
- H: Hand (manual action)
Succeeding Letters (Readout or Output Function):
- A: Alarm
- C: Controller
- I: Indicator
- T: Transmitter
- V: Valve
- Y: Calculation/Relay
- S: Switch
For example, FIT 202 is a Flow Indicating Transmitter in loop 202. LCV 305 is a Level Control Valve in loop 305. PAH 401 is a Pressure Alarm High in loop 401.
Flowsheet Connection and Signal Lines
Different lines represent the physical connection between instruments and process equipment:
Thick solid line: Major process piping.
Thin solid line: Minor process or utility piping (e.g., steam, cooling water).
Dashed line: Electrical signal (usually 4–20 mA or 1–5 V, represented by a dashed line or a dashed line with single diagonal ticks).
Solid line with double diagonal slashes: Pneumatic signal (usually 3–15 psig air).
Solid line with Xs: Capillary tubing (filled with system fluid).
Dotted line or line with bubbles: Software or data link (DCS communication, fieldbus).
Sine wave line: Electromagnetic, sonic, or optical signal.
Control Loop Configurations
Control loops are categorized based on their structural design:
Feedback Control: The controller measures the controlled variable (e.g., temperature) and compares it with the setpoint. It adjusts the manipulated variable (e.g., steam valve opening) based on the error. This is reactive and only corrects disturbances after they affect the process.
Feedforward Control: The controller measures a major disturbance stream before it enters the process. It calculates the necessary adjustment to the manipulated variable to cancel out the disturbance's impact. Feedforward is proactive but requires a detailed process model and is rarely used alone; it is typically paired with feedback control.
Cascade Control: Two controllers are nested. The primary (outer) controller measures the main process variable (e.g., reactor temperature) and calculates a setpoint for the secondary (inner) controller (e.g., jacket cooling water flow controller). Cascade control responds rapidly to disturbances in the utility line (jacket flow) before they can affect the primary process variable (reactor temperature).
Ratio Control: Maintains a constant ratio between two stream flow rates. Typically, one stream is designated as wild (uncontrolled) and its flow rate is measured to determine the setpoint for the controlled stream's flow controller. This is common in fuel-air combustion systems and reactor feed blending.
Split-Range Control: A single controller output signal is split between two final control elements. For example, a temperature controller might open a cooling water valve when the output is 0–50% and open a steam valve when the output is 50–100%.
Regulatory and Design Standards
Chemical process design must conform to national and international standards to ensure safety, quality, and environmental compliance:
OSHA 29 CFR 1910.119 (Process Safety Management - PSM): Mandates that facilities handling highly hazardous chemicals maintain highly accurate, up-to-date P&IDs and Process Safety Information (PSI). The P&IDs serve as the baseline for mandatory Process Hazard Analyses (PHAs), such as Hazard and Operability (HAZOP) studies.
ISO 10628 (Flow Diagrams for Process Plants): Establishes general rules for the drawing and structure of PFDs, P&IDs, and block diagrams.
ASTM Standards: Specify material properties, testing methods, and fabrication limits for piping, pressure vessels, and flanges.
ISA-5.1: Governs the standard symbols and identification codes used for process instrumentation.
Worked Example: Interpreting a Control Loop on a P&ID
Consider a shell-and-tube heat exchanger heating a cold process stream using condensing steam on the shell side. A temperature transmitter (TT 102) is mounted on the process outlet line. The TT 102 sends an electrical signal (represented by a dashed line) to a temperature indicating controller (TIC 102), which is shown as a circle inside a square with a single horizontal line. The TIC 102 compares the temperature to a setpoint and sends an electrical signal to a current-to-pressure transducer (TY 102). The TY 102 converts the electrical signal into a pneumatic signal (represented by a line with double slashes) that actuates a control valve (TV 102) on the steam utility inlet line.
Let's analyze each component of this system:
TT 102: A field-mounted temperature transmitter (circle with no horizontal lines) that senses the temperature of the exiting stream.
TIC 102: A temperature indicating controller located in the main control panel (circle inside a square with a single solid horizontal line). The circle inside the square indicates that it is a shared display DCS instrument.
TY 102: A signal converter or transducer. In this case, it is an I/P (current-to-pressure) transducer, converting the controller's electrical current output (e.g., 4–20 mA) to a pneumatic pressure signal (e.g., 3–15 psig) to drive the physical diaphragm of the steam valve.
TV 102: The temperature control valve on the steam supply line.
This represents a classic feedback control loop. If the outlet temperature drops below the setpoint, the controller senses the error, and increases the steam valve opening. If a disturbance occurs in the steam supply pressure, the feedback loop cannot react until the outlet temperature actually shifts, demonstrating the limitation of simple feedback systems compared to cascade configurations.