Study guide
11.2 Solids Transportation and Storage
NCEES Fundamentals of Engineering FE
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Mathematics
1.1 Analytic Geometry, Algebra, and Trigonometry 1.2 Calculus and Differential Equations 1.3 Numerical Methods and Measurement Error
2 Chapter 2: Probability and Statistics
2.1 Probability Distributions, Central Tendency, and Regression 2.2 Hypothesis Testing, ANOVA, and Statistical Quality Control
3 Chapter 3: Engineering Sciences
3.1 Mechanics and Dynamics 3.2 Electrical Circuits and Laws
4 Chapter 4: Materials Science
4.1 Material Properties and Compatibilities 4.2 Corrosion, Polymers, Ceramics, and Composites
5 Chapter 5: Chemistry and Biology
5.1 Stoichiometry, Analytical Chemistry, and Chemical Equilibrium 5.2 Organic Chemistry and Nomenclature 5.3 Biological Systems and Kinetics
6 Chapter 6: Fluid Mechanics and Dynamics
6.1 Fluid Properties, Dimensionless Numbers, and Flow Regimes 6.2 Bernoulli Equation and Mechanical Energy Balances 6.3 Flow Measurement and Fluid Machinery 6.4 Compressible and Non-Newtonian Flows
7 Chapter 7: Thermodynamics
7.1 Thermodynamic Properties, Ideal Gas, and State Equations 7.2 Laws of Thermodynamics and Cyclic Processes 7.3 Vapor-Liquid Equilibrium (VLE) and Phase Equilibrium 7.4 Chemical Equilibrium, Heats of Reaction, and Mixing
8 Chapter 8: Material and Energy Balances
8.1 Steady-State Material Balances 8.2 Unsteady-State Mass Balances 8.3 Steady-State Energy Balances 8.4 Unsteady-State Energy Balances
9 Chapter 9: Heat Transfer
9.1 Conduction, Convection, and Radiation Fundamentals 9.2 Heat Transfer Coefficients, Fouling, and Overall U 9.3 Heat Exchanger Design
10 Chapter 10: Mass Transfer and Separation
10.1 Diffusion Fundamentals 10.2 Gas Absorption, Stripping, and Liquid-Liquid Extraction 10.3 Distillation and McCabe-Thiele Method 10.4 Continuous Contact Methods, Membrane Separations, and Evaporative Operations
11 Chapter 11: Solids Handling
11.1 Particle Properties and Solid Processing 11.2 Solids Transportation and Storage
12 Chapter 12: Chemical Reaction Engineering
12.1 Reaction Kinetics and Performance Metrics 12.2 Ideal Reactor Design 12.3 Multiple Reactions, Catalysis, and Heterogeneous Kinetics
13 Chapter 13: Economics
13.1 Time Value of Money and Project Selection 13.2 Profitability Analysis, Depreciation, and Break-Even
14 Chapter 14: Process Design
14.1 Process Flowsheets and Instrumentation 14.2 Equipment Selection, Sizing, and Cost Estimation 14.3 Process Optimization, Sustainability, and Inherently Safer Design
15 Chapter 15: Process Control
15.1 Process Dynamics and Transfer Functions 15.2 Feedback Control Loops, PID Tuning, and Control Hardware
16 Chapter 16: Safety, Health, and Environment
16.1 Flammability, Toxicity, and Industrial Hygiene 16.2 Hazard Identification and Risk Analysis 16.3 Overpressure Relief, Reactivity Hazards, and Waste Regulations
17 Chapter 17: Ethics and Professional Practice
17.1 Professional Codes of Ethics and Public Welfare 17.2 Intellectual Property, Contracts, and Professional Liability
11.2 Solids Transportation and Storage
Key Takeaways Explain This Topic AI
Belt conveyor capacity is determined by belt velocity and the cross-sectional area of the solid load, with inclinations limited to prevent slip.
Screw conveyor delivery is modeled based on rotating speed, pitch, diameter, and loading factor, with factors kept low for abrasive materials.
Pneumatic conveying is divided into dilute phase (suspension flow, high-velocity) and dense phase (non-suspended plug flow, low-velocity).
Slurry transport relies on velocity exceeding the critical deposition velocity to avoid solids settling and blocking pipelines.
Bulk solids storage silos experience wall-friction effects described by Janssen's equation, requiring mass flow hopper design to avoid arching and ratholing.
Last updated: July 2026
- 11.2 Solids Transportation and Storage
- 1. Solids Transportation Systems
Moving bulk solids is a critical operational task in chemical plants. Transportation systems are split into mechanical conveying and fluid-based piping systems.
Belt Conveyors: Used for horizontal or slightly inclined transport ( < 20 ∘ <20^\circ < 2 0 ∘ ) over long distances. The volumetric capacity ( Q Q Q , m 3 / h \text{m}^3/\text{h} m 3 / h ) is determined by the cross-sectional area of the solid load on the belt ( A A A , m 2 \text{m}^2 m 2 ) and belt velocity ( v v v , m/s \text{m/s} m/s ): Q = 3600 ⋅ A ⋅ v Q = 3600 \cdot A \cdot v Q = 3600 ⋅ A ⋅ v
The cross-sectional area A A A depends on the belt width, the shape of the idlers (troughed vs. flat), and the material's dynamic surcharge angle.
Screw Conveyors: Consist of a rotating helical screw flight in a stationary trough. They are ideal for short distances ( < 30 m <30\text{ m} < 30 m ) and can operate at steep inclines. Capacity ( Q s Q_s Q s , m 3 / h \text{m}^3/\text{h} m 3 / h ) is calculated as: Q s = 60 ⋅ π 4 ( D s 2 − ( D s c ) 2 ) ⋅ P ⋅ n ⋅ η L Q_s = 60 \cdot \frac{\pi}{4} (D_s^2 - (D_s^c)^2) \cdot P \cdot n \cdot \eta_L Q s = 60 ⋅ 4 π ( D s 2 − ( D s c ) 2 ) ⋅ P ⋅ n ⋅ η L
where D s D_s D s is the screw diameter, D s c D_s^c D s c is the shaft diameter, P P P is the pitch, n n n is rotational speed in rpm, and η L \eta_L η L is the loading factor. The loading factor is typically 15% to 30% for abrasive solids to minimize wear, and up to 45% for non-abrasive, free-flowing solids.
Pneumatic Conveying: Uses a gas stream (usually air) to transport particles through pipelines.
Dilute Phase: Particles are fully suspended in high-velocity air ( 15 − 35 m/s 15 - 35\text{ m/s} 15 − 35 m/s ) at low pressure. The air velocity must exceed the saltation velocity (horizontal pipes) or choking velocity (vertical pipes) to prevent settling. High velocities cause pipe erosion and particle attrition.
Dense Phase: Particles slide or move in plugs along the pipe at low velocities ( 1 − 10 m/s 1 - 10\text{ m/s} 1 − 10 m/s ) under high pressure. This regime minimizes erosion and is ideal for fragile or abrasive materials.
Slurry Transport: Involves pumping solid-liquid mixtures through pipelines. To prevent settling, the slurry velocity must exceed the critical deposition velocity ( v D v_D v D ), which Durand's equation estimates: v D = F L 2 g D p ( ρ s − ρ f ρ f ) v_D = F_L \sqrt{2 g D_p \left(\frac{\rho_s - \rho_f}{\rho_f}\right)} v D = F L 2 g D p ( ρ f ρ s − ρ f )
where F L F_L F L is an empirical factor, g g g is gravity, D p D_p D p is pipe diameter, ρ s \rho_s ρ s is solid density, and ρ f \rho_f ρ f is fluid density.
2. Solids Storage and Silo Design
Bulk solids are stored in vertical bins, silos, or hoppers. Unlike liquids, which exert hydrostatic pressure increasing linearly with depth ( P = ρ g h P = \rho g h P = ρ g h ), bulk solids transfer their weight to the walls through friction. Consequently, the vertical pressure in a silo asymptotes to a maximum limit at deep levels. This behavior is modeled by Janssen’s Equation : σ v = ρ b g R h μ w K [ 1 − e − μ w K z R h ] \sigma_v = \frac{\rho_b g R_h}{\mu_w K} \left[ 1 - e^{-\frac{\mu_w K z}{R_h}} \right] σ v = μ w K ρ b g R h [ 1 − e − R h μ w Kz ]
where σ v \sigma_v σ v is vertical stress, ρ b \rho_b ρ b is bulk density, R h R_h R h is hydraulic radius of the silo cross-section, μ w \mu_w μ w is the wall friction coefficient ( tan ϕ ′ \tan\phi' tan ϕ ′ ), and K K K is the lateral-to-vertical pressure ratio. The lateral stress on the wall is σ h = K σ v \sigma_h = K \sigma_v σ h = K σ v .
3. Flow Patterns and Discharge Obstructions
When discharging solids from a hopper, two main flow patterns can occur:
Mass Flow: The entire solid mass is in motion. This produces a "first-in, first-out" sequence, eliminating stagnant zones and segregation. It requires steep, smooth walls, which increases height and causes wall wear.
Funnel Flow: Material flows only through a central channel. Solids near the walls remain stagnant, producing a "first-in, last-out" sequence. This occurs in shallow or rough hoppers and can lead to product degradation or silo instability.
Hoppers can fail to discharge due to two major obstructions:
Arching (Bridging): A stable cohesive arch forms over the outlet, blocking flow.
Ratholing (Piping): Solid drains from the center, leaving a stable empty core surrounded by stagnant material.
To prevent arching, the minimum hopper outlet width ( B B B ) is designed as: B ≥ H ( θ ′ ) σ ˉ 1 g ρ b B \ge \frac{H(\theta') \bar{\sigma}_1}{g \rho_b} B ≥ g ρ b H ( θ ′ ) σ ˉ 1
where H ( θ ′ ) H(\theta') H ( θ ′ ) is a geometry factor and σ ˉ 1 \bar{\sigma}_1 σ ˉ 1 is the bulk strength of the solid.
4. Worked Examples
Example 1: Slurry Transport Critical Velocity A sand slurry ( ρ s = 2650 kg/m 3 \rho_s = 2650\text{ kg/m}^3 ρ s = 2650 kg/m 3 ) in water ( ρ f = 1000 kg/m 3 \rho_f = 1000\text{ kg/m}^3 ρ f = 1000 kg/m 3 ) is transported in a 0.20 m 0.20\text{ m} 0.20 m diameter pipe. If the empirical factor F L F_L F L is 1.40 1.40 1.40 , calculate the critical deposition velocity ( v D v_D v D ) in m/s.
Solution: Durand's equation is: v D = F L 2 g D p ( ρ s − ρ f ρ f ) v_D = F_L \sqrt{2 g D_p \left(\frac{\rho_s - \rho_f}{\rho_f}\right)} v D = F L 2 g D p ( ρ f ρ s − ρ f )
Calculate the density ratio term: ρ s − ρ f ρ f = 2650 − 1000 1000 = 1.65 \frac{\rho_s - \rho_f}{\rho_f} = \frac{2650 - 1000}{1000} = 1.65 ρ f ρ s − ρ f = 1000 2650 − 1000 = 1.65
Substitute parameters: v D = 1.40 ⋅ 2 ⋅ 9.81 m/s 2 ⋅ 0.20 m ⋅ 1.65 v_D = 1.40 \cdot \sqrt{2 \cdot 9.81\text{ m/s}^2 \cdot 0.20\text{ m} \cdot 1.65} v D = 1.40 ⋅ 2 ⋅ 9.81 m/s 2 ⋅ 0.20 m ⋅ 1.65 v D = 1.40 ⋅ 6.4746 ≈ 1.40 ⋅ 2.5445 ≈ 3.56 m/s v_D = 1.40 \cdot \sqrt{6.4746} \approx 1.40 \cdot 2.5445 \approx 3.56\text{ m/s} v D = 1.40 ⋅ 6.4746 ≈ 1.40 ⋅ 2.5445 ≈ 3.56 m/s
The critical deposition velocity is 3.56 m/s.
Example 2: Screw Conveyor Capacity Sizing Determine the volumetric capacity in m 3 / h \text{m}^3/\text{h} m 3 / h of a screw conveyor with a screw diameter of 0.40 m 0.40\text{ m} 0.40 m , a shaft diameter of 0.10 m 0.10\text{ m} 0.10 m , and a pitch of 0.35 m 0.35\text{ m} 0.35 m rotating at 50 rpm 50\text{ rpm} 50 rpm with a trough loading factor of 25 % 25\% 25% .
Solution:
Calculate cross-sectional area: A = π 4 ( D s 2 − ( D s c ) 2 ) = π 4 ( 0.40 2 − 0.10 2 ) = π 4 ( 0.16 − 0.01 ) = π 4 ( 0.15 ) ≈ 0.1178 m 2 A = \frac{\pi}{4} (D_s^2 - (D_s^c)^2) = \frac{\pi}{4} (0.40^2 - 0.10^2) = \frac{\pi}{4} (0.16 - 0.01) = \frac{\pi}{4} (0.15) \approx 0.1178\text{ m}^2 A = 4 π ( D s 2 − ( D s c ) 2 ) = 4 π ( 0.4 0 2 − 0.1 0 2 ) = 4 π ( 0.16 − 0.01 ) = 4 π ( 0.15 ) ≈ 0.1178 m 2
Use capacity formula: Q s = 60 ⋅ A ⋅ P ⋅ n ⋅ η L Q_s = 60 \cdot A \cdot P \cdot n \cdot \eta_L Q s = 60 ⋅ A ⋅ P ⋅ n ⋅ η L Q s = 60 ⋅ 0.1178 m 2 ⋅ 0.35 m ⋅ 50 rpm ⋅ 0.25 Q_s = 60 \cdot 0.1178\text{ m}^2 \cdot 0.35\text{ m} \cdot 50\text{ rpm} \cdot 0.25 Q s = 60 ⋅ 0.1178 m 2 ⋅ 0.35 m ⋅ 50 rpm ⋅ 0.25 Q s = 60 ⋅ 0.1178 ⋅ 4.375 = 30.92 m 3 / h Q_s = 60 \cdot 0.1178 \cdot 4.375 = 30.92\text{ m}^3/\text{h} Q s = 60 ⋅ 0.1178 ⋅ 4.375 = 30.92 m 3 / h
The capacity is approximately 30.9 m 3 / h \text{m}^3/\text{h} m 3 / h .