Study guide

4.5 Environmental Engineering (Water & Wastewater)

FE Civil Fundamentals of Engineering — Civil

Track your progress as you read

Finished sections get a check mark.

1 Introduction & FE Civil Exam Strategy

1.1 FE Civil Exam Facts (2026) 1.2 Mastering the NCEES FE Reference Handbook 1.3 Computational Tools & Numerical Methods 1.4 Study Plan, Pacing & Exam-Day Logistics

2 Mathematics, Probability, Statistics & General Topics

2.1 Mathematics (Algebra, Trigonometry, Geometry & Calculus) 2.2 Probability & Statistics 2.3 Engineering Sciences 2.4 Ethics & Professional Practice 2.5 Engineering Economics

3 Statics, Dynamics & Mechanics of Materials

3.1 Statics I: Resultants, Equilibrium & Trusses 3.2 Statics II: Friction, Centroids & Moment of Inertia 3.3 Dynamics (Kinematics & Kinetics) 3.4 Mechanics of Materials I: Stress, Strain & Axial Loading 3.5 Mechanics of Materials II: Beams, Torsion, Bending & Columns 3.6 Civil Engineering Materials

4 Fluid Mechanics, Hydraulics & Water Resources

4.1 Fluid Properties & Fluid Statics 4.2 Fluid Dynamics: Continuity, Bernoulli & Momentum 4.3 Hydraulics: Pipe Flow, Open Channel & Pumps 4.4 Hydrologic Systems 4.5 Environmental Engineering (Water & Wastewater)

5 Geotechnical & Structural Engineering

5.1 Soil Classification & Index Properties 5.2 Soil Mechanics: Effective Stress, Consolidation & Shear Strength 5.3 Foundations, Retaining Walls & Slope Stability 5.4 Structural Analysis 5.5 Structural Design (Steel & Reinforced Concrete) 5.6 Loads, Load Combinations & Design Codes

6 Transportation, Construction & Surveying

6.1 Transportation: Geometric Design 6.2 Transportation: Traffic Engineering & Pavement 6.3 Construction: Scheduling, Earthwork & Estimating 6.4 Construction: Means, Methods & Safety 6.5 Surveying

4.5 Environmental Engineering (Water & Wastewater)

Key Takeaways Explain This Topic AI

BOD (Biochemical Oxygen Demand) measures biodegradable organics; the standard test is BOD₅ at 20°C, modeled by BOD_t = L₀(1 − e^(−kt))

Hydraulic detention time θ = V/Q sizes tanks; a tank of volume V passing flow Q holds water for θ on average

Drinking-water train: coagulation → flocculation → sedimentation → filtration → disinfection

Conventional wastewater train: primary (settling) → secondary (biological, e.g., activated sludge) → tertiary (nutrient/polishing) → disinfection

  • A completely-mixed reactor mass balance: accumulation = inflow − outflow ± reaction (in − out ± rxn)
  • Last updated: June 2026

Water-Quality Parameters

Environmental items test the indicators that define water quality. Biochemical Oxygen Demand (BOD) is the oxygen microbes consume to break down biodegradable organics; the standard BOD₅ is measured over 5 days at 20°C. First-order kinetics give BOD_t = L₀(1 − e^(−kt)) , where L₀ is the ultimate BOD and k is the rate constant (day⁻¹). Chemical Oxygen Demand (COD) oxidizes both biodegradable and non-biodegradable matter chemically, so COD ≥ BOD always.

Other key parameters: Dissolved Oxygen (DO) sustains aquatic life (a healthy stream holds several mg/L; saturation DO falls as temperature rises, so warm water holds less oxygen — thermal pollution is harmful). High BOD discharged to a stream depletes DO downstream, creating the classic DO sag curve (modeled by the Streeter-Phelps equation, balancing deoxygenation against reaeration). Turbidity (cloudiness, in Nephelometric Turbidity Units, NTU) indicates suspended particles and interferes with disinfection; drinking water is typically held below ~1 NTU after filtration.

pH (0–14, neutral 7) measures acidity/alkalinity and affects coagulation, disinfection, and corrosion. Coliforms (especially E. coli ) are fecal-contamination indicator organisms — easy to test for and signaling possible pathogens. S. Safe Drinking Water Act sets a Maximum Contaminant Level Goal (MCLG) of zero for total coliforms. Other regulated items include total suspended solids (TSS) , total dissolved solids (TDS) , nitrogen and phosphorus (nutrients that cause eutrophication), and alkalinity/hardness (mostly Ca²⁺ and Mg²⁺, reported as mg/L of CaCO₃).

Drinking-Water Treatment Train

Conventional surface-water treatment follows a sequence; know the order and the purpose of each step:

Coagulation — add a coagulant (e.g., alum, Al₂(SO₄)₃) and rapid-mix to destabilize colloidal particles by neutralizing their charge.

Flocculation — gentle, slow mixing lets destabilized particles collide and grow into settleable floc .

Sedimentation — floc settles out by gravity in a clarifier; design uses the overflow rate (surface loading) = Q/A_surface , which equals the critical settling velocity captured.

Filtration — typically rapid sand or dual-media filters remove remaining fine particles.

Disinfection — chlorine, chloramine, ozone, or ultraviolet (UV) light inactivates pathogens; chlorine also leaves a measurable residual to protect the distribution system, which UV and ozone do not provide. Disinfection effectiveness follows the CT concept (disinfectant concentration × contact time): a higher CT achieves greater log-removal of organisms.

Softening (lime-soda or ion exchange) may be added to remove hardness, and fluoridation for dental health. Sedimentation-basin sizing hinges on the overflow rate v_o = Q/A_surface : a particle settles out only if its settling velocity exceeds v_o, so a larger surface area captures finer particles — note that detention time alone does not govern removal, the surface loading does.

  • Parameter Meaning Note
  • BOD Biodegradable organic load BOD₅ at 20°C
  • COD Total chemically oxidizable matter COD ≥ BOD
  • DO Dissolved oxygen Lower as temp rises
  • Turbidity Cloudiness (NTU) Suspended solids
  • Coliforms Fecal indicator MCLG = 0

Wastewater Treatment & the Activated-Sludge Process

Municipal wastewater treatment removes organics, solids, and nutrients in stages:

Preliminary — bar screens and grit removal protect downstream equipment.

Primary — quiescent sedimentation removes ~50–60% of suspended solids and ~30–35% of BOD by settling.

Secondary (biological) — microorganisms metabolize dissolved/colloidal organics. In the activated-sludge process , an aeration basin grows a biomass (measured as Mixed Liquor Suspended Solids, MLSS) that is settled in a secondary clarifier and partly recycled (Return Activated Sludge). Secondary treatment removes ~85–95% of BOD. Trickling filters are an attached-growth alternative.

Tertiary/advanced — nutrient removal (nitrogen, phosphorus), filtration, polishing.

Disinfection — chlorination/dechlorination or UV before discharge.

A frequent exam concept is removal efficiency E = (C_in − C_out)/C_in × 100%, and combining stages (overall removal compounds through the train).

Mass Balances, Detention Time & a Worked Example

The workhorse tool is the mass balance on a control volume: accumulation = mass in − mass out ± reaction . At steady state, accumulation = 0, so in = out ± reaction. For a completely-mixed flow reactor (CMFR) with first-order decay, the effluent concentration satisfies C_out = C_in/(1 + kθ).

The hydraulic detention (retention) time is θ = V/Q , the average time a parcel of water spends in a tank of volume V passing flow Q. It sizes sedimentation basins, aeration tanks, and disinfection contact chambers. Watch your units — flow in MGD or m³/min must be converted so V comes out in the desired unit; carrying minutes versus hours is a common slip.

For a simple flow-blending mass balance with no reaction, the combined concentration of two merging streams is C = (Q₁C₁ + Q₂C₂)/(Q₁ + Q₂) — a flow-weighted average. The same in/out bookkeeping handles chemical dosing (mass added = Q × dose) and removal across a unit process. When a reaction consumes the constituent (e.g., first-order decay of BOD or a disinfectant), include the reaction term: rate = −kC·V for first-order kinetics. These mass-balance setups, combined with detention time, answer most FE environmental design questions, so always write 'in − out ± reaction = accumulation' first and then simplify.

Worked Detention-Time Example

A sedimentation basin must hold wastewater for θ = 2 hours at a flow of Q = 5 million gallons per day (MGD). Find the required volume.

Convert Q: 5 MGD = 5,000,000 gal/day ÷ 24 h = 208,333 gal/h.

V = Q·θ = 208,333 gal/h × 2 h = 416,667 gallons.

In cubic feet: 416,667 gal ÷ 7.48 gal/ft³ = 55,700 ft³ .

Solid waste and air (high level): municipal solid waste (MSW) is managed by reduction, recycling, composting, waste-to-energy, and engineered landfills with liners and leachate/gas collection. Air topics include criteria pollutants (PM, SO₂, NOₓ, CO, O₃, Pb) and basic dispersion concepts — these appear lightly on FE Civil.