Study guide

Bending Stress and Torsion

FE Fundamentals of Engineering Exam

Track your progress as you read

Finished sections get a check mark.

1 Introduction to the FE Exam

About the FE Exam FE Exam Study Strategies Navigating the FE Reference Handbook

2 Mathematics (8–12 Questions)

Analytic Geometry and Trigonometry Single-Variable Calculus Differential Equations Linear Algebra and Matrix Operations Numerical Methods

3 Probability and Statistics (6–9 Questions)

Probability Fundamentals Probability Distributions Statistical Estimation and Hypothesis Testing

4 Chemistry (5–8 Questions)

Chemical Reactions and Stoichiometry Acids, Bases, and pH Oxidation-Reduction and Corrosion

5 Ethics and Professional Practice (5–8 Questions)

Engineering Ethics Fundamentals

6 Engineering Economics (6–9 Questions)

Time Value of Money Economic Analysis Methods

7 Statics (9–14 Questions)

Force Systems and Equilibrium Trusses, Frames, and Machines Centroids and Moments of Inertia Static Friction

8 Dynamics (9–14 Questions)

Particle Kinematics Kinetics: Force, Mass, and Acceleration Work, Energy, Impulse, and Momentum Rigid-Body Rotation and Mechanical Vibrations

9 Strength of Materials (9–14 Questions)

Stress and Strain Fundamentals Beam Analysis: Shear and Moment Diagrams Bending Stress and Torsion Stress Transformation and Material Failure

10 Materials Science (6–9 Questions)

Material Properties and Selection Phase Diagrams and Alloy Systems

11 Fluid Mechanics (12–18 Questions)

Fluid Properties and Statics Fluid Dynamics and Bernoulli's Equation Pumps, Turbines, and Flow Measurement

12 Thermodynamics and Heat Transfer (9–14 Questions)

Laws of Thermodynamics and Properties Thermodynamic Cycles and Applications Heat Transfer: Conduction, Convection, and Radiation

13 Basic Electrical Engineering (6–9 Questions)

Electrical Fundamentals and DC Circuits AC Circuits and Three-Phase Power

14 Safety, Health, and Environment (6–9 Questions)

Industrial Safety and Hazard Management

15 Instrumentation and Controls (4–6 Questions)

Sensors, Data Acquisition, and Control Systems

16 Computational Tools and Computer Science

Spreadsheets, Structured Programming, and Flowcharts

Bending Stress and Torsion

Key Takeaways Explain This Topic AI

Bending stress varies linearly across the section: σ = My/I, with the maximum σ_max = Mc/I = M/S at the extreme fiber (S = I/c is the section modulus).

Transverse shear stress in a beam is τ = VQ/(Ib), maximum at the neutral axis — the opposite location to maximum bending stress.

For a rectangular section τ_max = 3V/(2A) = 1.5τ_avg; for a circular section τ_max = 4V/(3A) = 1.33τ_avg.

Torsion of a circular shaft: τ = Tr/J, maximum at the outer surface τ_max = Tc/J.

Polar moment of inertia: solid shaft J = πd⁴/32, hollow shaft J = π(d_o⁴ − d_i⁴)/32; angle of twist φ = TL/(GJ).

Transmitted power P = Tω, with ω = 2πn/60 for n in rpm — the standard way torque and motor speed are linked.

Last updated: June 2026

Bending (Flexure) Stress

In pure bending, plane sections stay plane and the normal stress varies linearly from the neutral axis , which passes through the centroid:

σ = M y / I

where M is the bending moment, y is the distance from the neutral axis, and I is the centroidal moment of inertia. Stress is zero at the neutral axis and largest at the extreme fiber, where y = c:

σ_max = M c / I = M / S

The section modulus S = I/c packages the geometry into one number, so σ_max = M/S — a larger S means lower stress for the same moment. For a sagging (positive M) beam, the top fiber is in compression and the bottom in tension.

Section properties of common shapes

  • Shape I (about centroid) c S = I/c
  • Rectangle (b × h) bh³/12 h/2 bh²/6
  • Solid circle (dia. d) πd⁴/64 d/2 πd³/32
  • Hollow circle π(d_o⁴ − d_i⁴)/64 d_o/2 π(d_o⁴ − d_i⁴)/(32 d_o)
  • Worked example — maximum bending stress

A rectangular beam 50 mm wide × 100 mm tall carries M = 10 kN·m. Find σ_max.

S = bh²/6 = (50)(100²)/6 = 500,000/6 = 83,333 mm³.

Convert moment to N·mm: M = 10 kN·m = 10×10⁶ N·mm.

σ_max = M/S = 10×10⁶ / 83,333 = 120 MPa .

The trap is the moment unit: 10 kN·m = 10,000 N·m = 10,000,000 N·mm. Forgetting the ×1000 (kN→N) and the ×1000 (m→mm) is the classic error.

Transverse Shear Stress

Where the bending moment changes (dM/dx = V ≠ 0), a transverse shear stress acts on the cross-section:

  • τ = V Q / (I b)
  • V = shear force at the section
  • Q = first moment of the area above (or below) the level of interest, taken about the neutral axis: Q = A′ ȳ′
  • I = moment of inertia of the whole section
  • b = section width at the level of interest

Because Q is largest at the neutral axis, maximum transverse shear occurs at the neutral axis — exactly where bending stress is zero. This complementary pattern is a favorite FE distinction.

  • Section τ_max Relation to average
  • Rectangle 3V/(2A) 1.5 × τ_avg
  • Solid circle 4V/(3A) 1.33 × τ_avg
  • I-beam (approx.) ≈ V/A_web concentrated in the web
  • Torsion of Circular Shafts

For a circular shaft carrying torque T, the shear stress grows linearly from the center:

τ = T r / J

with the maximum at the outer surface (r = c = d/2), τ_max = Tc/J. The polar moment of inertia J is:

  • Solid shaft: J = πd⁴/32
  • Hollow shaft: J = π(d_o⁴ − d_i⁴)/32
  • Worked example — polar moment and shaft stress

For a solid shaft d = 50 mm carrying T = 2 kN·m:

J = πd⁴/32 = π(50⁴)/32 = π(6,250,000)/32 = 613,592 mm⁴.

c = d/2 = 25 mm; T = 2×10⁶ N·mm.

τ_max = Tc/J = (2×10⁶)(25)/613,592 = 50×10⁶/613,592 = 81.5 MPa .

  • Angle of Twist
  • φ = T L / (G J) (radians)

The twist is proportional to torque and length and inversely proportional to the shaft's stiffness GJ. For shafts in series, sum φ segment by segment, just as with axial δ.

Power Transmission

A rotating shaft transmits power:

P = T ω, where ω = 2πn/60 for n in rpm

P is in watts when T is in N·m and ω in rad/s. Rearranged to size a shaft from a motor rating: T = P/ω.

Worked example — torque from motor power

A motor delivers 50 kW at 1,500 rpm. Find the shaft torque.

ω = 2π(1,500)/60 = 157.08 rad/s.

T = P/ω = 50,000 / 157.08 = 318.3 N·m .

Note the inverse relationship: at fixed power, higher rpm means lower torque, so high-speed shafts can be slimmer.

Putting It Together — Common Traps

Mc/I vs. Tr/J. Bending uses the area moment of inertia I = πd⁴/64 for a circle; torsion uses the polar moment J = πd⁴/32. Note J = 2I for a circle. Mixing them halves or doubles the stress.

Shear location. Bending stress is max at the extreme fiber; transverse shear is max at the neutral axis. They never peak at the same place.

Units. Convert kN·m to N·mm (×10⁶) before dividing by mm³ or mm⁴ section properties.

Hollow shafts are efficient. Removing the low-stress core near the center barely reduces J but saves weight — why drive shafts are tubes.

Quick reference

  • Action Formula Stress is max at
  • Bending σ = Mc/I = M/S Extreme fiber (y = c)
  • Transverse shear τ = VQ/(Ib) Neutral axis
  • Torsion τ = Tr/J Outer surface (r = c)
  • Twist φ = TL/(GJ) —
  • Power P = Tω, ω = 2πn/60 —

Section Modulus and Power Transmission

The bending-stress formula σ = Mc/I is often rewritten with the section modulus S = I/c, giving σ = M/S. Because S captures both I and c, beam selection tables list S directly — to keep stress below an allowable σ_allow, simply require S ≥ M_max/σ_allow. A larger S means a stronger section for the same bending moment.

For shafts, torsion connects to power transmission : P = Tω, where T is torque and ω is angular speed in rad/s. Given power and rpm, find T = P/ω, then the shear stress τ = Tc/J.

  • Quantity Relation
  • Section modulus S = I/c, σ = M/S
  • Required size S ≥ M_max/σ_allow
  • Shaft power P = Tω = T(2πN/60)
  • Worked Example

A motor delivers 10 kW at 1800 rpm: ω = 1800·2π/60 = 188.5 rad/s, so T = 10,000/188.5 = 53 N·m — the torque the shaft must carry.