Study guide
Stress Transformation and Material Failure
FE Fundamentals of Engineering Exam
Track your progress as you read
Finished sections get a check mark.
1 Introduction to the FE Exam
About the FE Exam FE Exam Study Strategies Navigating the FE Reference Handbook
2 Mathematics (8–12 Questions)
Analytic Geometry and Trigonometry Single-Variable Calculus Differential Equations Linear Algebra and Matrix Operations Numerical Methods
3 Probability and Statistics (6–9 Questions)
Probability Fundamentals Probability Distributions Statistical Estimation and Hypothesis Testing
4 Chemistry (5–8 Questions)
Chemical Reactions and Stoichiometry Acids, Bases, and pH Oxidation-Reduction and Corrosion
5 Ethics and Professional Practice (5–8 Questions)
Engineering Ethics Fundamentals
6 Engineering Economics (6–9 Questions)
Time Value of Money Economic Analysis Methods
7 Statics (9–14 Questions)
Force Systems and Equilibrium Trusses, Frames, and Machines Centroids and Moments of Inertia Static Friction
8 Dynamics (9–14 Questions)
Particle Kinematics Kinetics: Force, Mass, and Acceleration Work, Energy, Impulse, and Momentum Rigid-Body Rotation and Mechanical Vibrations
9 Strength of Materials (9–14 Questions)
Stress and Strain Fundamentals Beam Analysis: Shear and Moment Diagrams Bending Stress and Torsion Stress Transformation and Material Failure
10 Materials Science (6–9 Questions)
Material Properties and Selection Phase Diagrams and Alloy Systems
11 Fluid Mechanics (12–18 Questions)
Fluid Properties and Statics Fluid Dynamics and Bernoulli's Equation Pumps, Turbines, and Flow Measurement
12 Thermodynamics and Heat Transfer (9–14 Questions)
Laws of Thermodynamics and Properties Thermodynamic Cycles and Applications Heat Transfer: Conduction, Convection, and Radiation
13 Basic Electrical Engineering (6–9 Questions)
Electrical Fundamentals and DC Circuits AC Circuits and Three-Phase Power
14 Safety, Health, and Environment (6–9 Questions)
Industrial Safety and Hazard Management
15 Instrumentation and Controls (4–6 Questions)
Sensors, Data Acquisition, and Control Systems
16 Computational Tools and Computer Science
Spreadsheets, Structured Programming, and Flowcharts
Stress Transformation and Material Failure
Key Takeaways Explain This Topic AI
Principal stresses σ₁,₂ = (σx+σy)/2 ± √[((σx−σy)/2)² + τxy²] are the max/min normal stresses; shear is zero on principal planes.
Maximum in-plane shear τ_max = √[((σx−σy)/2)² + τxy²] = (σ₁−σ₂)/2, on planes 45° from the principal planes.
Mohr's circle has center C = (σx+σy)/2 and radius R = τ_max; principal stresses are C ± R.
Von Mises (distortion energy) predicts ductile yielding: σ_VM = √(σ₁² − σ₁σ₂ + σ₂²) ≥ σy; Tresca uses |σ₁ − σ₂| ≥ σy.
Euler buckling: P_cr = π²EI/(KL)²; use the smallest I (weakest axis) and the K for the end conditions.
Stress concentration σ_max = K_t·σ_nominal (K_t ≈ 3 for a small hole); fatigue and creep cause failure below σu under cyclic or hot sustained loads.
Last updated: June 2026
Plane Stress Transformation
A point in a loaded body has a stress state (σx, σy, τxy). Rotate the element by angle θ and the stresses change:
- σx' = (σx+σy)/2 + [(σx−σy)/2]cos2θ + τxy sin2θ
- τx'y' = −[(σx−σy)/2]sin2θ + τxy cos2θ
The quantity (σx+σy)/2 is the average normal stress and is invariant — it does not change with rotation. The goal is to find the orientation giving the largest normal stress (used for brittle failure) or the largest shear stress (used for ductile failure).
Principal Stresses and Maximum Shear
The principal stresses are the extreme normal stresses, occurring on planes where shear vanishes:
σ₁,₂ = (σx+σy)/2 ± √[((σx−σy)/2)² + τxy²]
The principal-plane angle is tan2θp = 2τxy/(σx − σy). The maximum in-plane shear stress equals the radical:
τ_max = √[((σx−σy)/2)² + τxy²] = (σ₁ − σ₂)/2
and acts on planes 45° from the principal planes. On those max-shear planes the normal stress equals the average (σx+σy)/2 — shear and principal planes are never the same plane.
Worked example — principal stresses and τ_max
Given σx = 80 MPa, σy = −40 MPa, τxy = 30 MPa:
Average = (80 + (−40))/2 = 20 MPa.
R = √[((80−(−40))/2)² + 30²] = √[(60)² + (30)²] = √(3,600 + 900) = √4,500 = 67.1 MPa.
σ₁ = 20 + 67.1 = 87.1 MPa; σ₂ = 20 − 67.1 = −47.1 MPa.
τ_max = R = 67.1 MPa .
The radius R is the maximum shear stress — a one-step shortcut once you build Mohr's circle.
Mohr's Circle
Mohr's circle turns the transformation equations into geometry on a σ–τ plot:
Center C = ((σx+σy)/2, 0).
Radius R = √[((σx−σy)/2)² + τxy²].
Principal stresses: σ₁ = C + R (right intercept), σ₂ = C − R (left intercept).
Maximum shear: τ_max = R (top/bottom of the circle).
Angles on the physical element double on the circle (a 90° physical rotation = 180° on the circle).
Mohr's circle is the fastest way to read off all three results — σ₁, σ₂, τ_max — at once.
- Failure Theories for Ductile Materials
- Maximum shear stress (Tresca)
Yielding begins when τ_max reaches σy/2, i.e. |σ₁ − σ₂| ≥ σy. Conservative and simple.
Distortion energy (von Mises)
Yielding begins when the equivalent stress reaches σy:
σ_VM = √(σ₁² − σ₁σ₂ + σ₂²) ≥ σy (plane stress)
Von Mises matches test data better than Tresca and is the standard choice in practice. For a pure shear state (σ₁ = −σ₂ = τ), von Mises predicts yield at τ = 0.577σy, whereas Tresca gives the more conservative 0.5σy.
Worked example — von Mises check
Using σ₁ = 87 MPa and σ₂ = −47 MPa from the earlier transformation, with σy = 250 MPa:
σ_VM = √(87² − (87)(−47) + (−47)²) = √(7,569 + 4,089 + 2,209) = √13,867 = 117.8 MPa.
Since 117.8 < 250 MPa, the material does not yield; the factor of safety is FS = σy/σ_VM = 250/117.8 = 2.1.
Maximum normal stress (brittle materials)
Brittle materials such as cast iron fail when σ₁ ≥ σ_ut (ultimate tensile) or |σ₂| ≥ σ_uc, not by yielding. For brittle parts the largest principal stress , not the shear, governs — which is why a chalk stick twisted in torsion fractures on a 45° helix (the plane of maximum tension).
Column Buckling — Euler's Formula
Long, slender columns fail by elastic instability long before the material yields:
P_cr = π²EI / (KL)²
or as a critical stress σ_cr = π²E/(KL/r)², where r = √(I/A) is the radius of gyration and KL/r is the slenderness ratio .
Worked example — Euler buckling load
A 3 m column, pinned–pinned (K = 1.0), E = 200 GPa, I = 5×10⁶ mm⁴:
KL = 1.0 × 3,000 = 3,000 mm.
P_cr = π²EI/(KL)² = π²(200,000)(5×10⁶)/(3,000²)
= (9.87)(1×10¹²)/(9×10⁶) = 1,097 kN .
Effective Length Factor K
- End conditions K P_cr relative to pinned–pinned
- Fixed–fixed 0.5 4× higher
- Fixed–pinned 0.7 ~2× higher
- Pinned–pinned 1.0 reference
- Fixed–free (cantilever) 2.0 4× lower
Two non-negotiable rules: (1) use the smallest I — a column buckles about its weakest axis; (2) Euler's formula is valid only for slender columns (high KL/r); short columns fail by yielding instead, governed by σ = P/A.
Stress Concentrations
Near holes, notches, and fillets, local stress is amplified:
σ_max = K_t · σ_nominal
where K_t ≥ 1 is the stress concentration factor. For a small circular hole in a wide plate under tension, K_t ≈ 3 — the stress at the hole edge is triple the nominal. Ductile materials yield locally and redistribute, so K_t matters most for brittle materials and fatigue.
Fatigue and Creep
- Phenomenon Description
- Fatigue Failure under repeated/cyclic loading at stresses below σu
- Endurance limit Stress below which steel survives infinite cycles (≈ 0.5σu)
- Creep Slow time-dependent deformation under sustained load at high temperature
- Quick reference
σ₁,₂ = avg ± R; τ_max = R = (σ₁−σ₂)/2; avg = (σx+σy)/2.
Von Mises: σ_VM = √(σ₁²−σ₁σ₂+σ₂²) ≥ σy (ductile). Brittle: σ₁ ≥ σ_ut.
Buckling: P_cr = π²EI/(KL)²; smallest I; K = 0.5/0.7/1.0/2.0.
Reading Mohr's Circle and Choosing a Failure Theory
Mohr's circle plots stress states: the center sits at σ_avg = (σx+σy)/2 and the radius R = √[((σx−σy)/2)² + τxy²]. The principal stresses are σ₁,₂ = σ_avg ± R (where shear is zero), and the maximum in-plane shear is τ_max = R. Each 2θ rotation on the circle equals a θ rotation of the physical element.
- Theory Use for Yields when
- Maximum shear (Tresca) Ductile, conservative τ_max = σ_y/2
- Distortion energy (von Mises) Ductile, accurate σ_vm = σ_y
- Maximum normal stress Brittle σ₁ = σ_ult
The factor of safety is FS = σ_failure/σ_applied. Choose Tresca or von Mises for ductile metals and maximum-normal-stress for brittle materials like cast iron — picking the wrong theory for the material is the classic trap.