Study guide
18.1 Methods Engineering, Process Charting, and Principles of Motion Economy
FE Industrial and Systems Study Guide Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Exam Overview, CBT Strategy & Handbook Navigation
1.1 FE Industrial Exam Structure, CBT Logistics, and Pacing 1.2 Using the NCEES FE Reference Handbook and Approved Calculators
2 Chapter 2: Mathematics for Industrial Engineers
2.1 Analytic Geometry, Coordinate Systems, and Trigonometry 2.2 Calculus: Differential, Integral, and Series Approximations 2.3 Linear Algebra: Matrix Operations, Systems of Equations, and Vectors
3 Chapter 3: Engineering Sciences Core
3.1 Thermodynamics Fundamentals and Fluid Flow Principles 3.2 Statics, Dynamics, and Mechanics of Materials Core 3.3 Electrical Circuits, DC/AC Analysis, and Power in Industrial Systems
4 Chapter 4: Ethics and Professional Practice
4.1 NCEES Model Rules of Professional Conduct and Technical Society Ethics 4.2 Engineering Licensure, Public Welfare, and Professional Liability 4.3 Engineering Contracts, Intellectual Property, and Conflicts of Interest
5 Chapter 5: Engineering Economics
5.1 Time Value of Money, Discount Factors, and Equivalence 5.2 Evaluating Alternatives: Present Worth, Equivalent Annual Cost, and IRR 5.3 Incremental Rate of Return, Replacement Analysis, and Break-Even 5.4 Depreciation Methods, MACRS, Income Taxes, and Inflation
6 Chapter 6: Probability Foundations & Distributions
6.1 Basic Probability Concepts, Conditional Probability, and Bayes' Theorem 6.2 Discrete Probability Distributions 6.3 Continuous Probability Distributions
7 Chapter 7: Statistical Inference, Regression & Design of Experiments
7.1 Sampling Distributions, Central Limit Theorem, and Confidence Intervals 7.2 Hypothesis Testing: Means, Proportions, and Variances 7.3 Linear Regression, Correlation Analysis, and Design of Experiments (ANOVA)
8 Chapter 8: Data, Logic, Modeling & Linear Programming
8.1 Optimization Modeling: Decision Variables, Objectives, and Constraints 8.2 Linear Programming: Graphical Solutions and Simplex Fundamentals 8.3 Duality, Sensitivity Analysis, and Integer Linear Programming 8.4 Data, Logic Development, and Analytics
9 Chapter 9: Stochastic Models & Simulation
9.1 Queuing Theory: Little's Law, M/M/1, and Multi-Server Systems 9.2 Discrete-Time Markov Chains: Transition Matrices and Steady-State Probabilities 9.3 Discrete-Event Simulation Principles and Monte Carlo Modeling
10 Chapter 10: Engineering Management, Project Planning & Performance Measurement
10.1 Organizational Structure, Leadership, and Worker Motivation Theories 10.2 Project Management: WBS, Critical Path Method (CPM), PERT, and Crashing 10.3 Earned Value Management (EVM), Decision Trees, and Risk Preference 10.4 Performance Measurement: Productivity, KPIs, Wage Systems, and the Balanced Scorecard
11 Chapter 11: Manufacturing & Production Systems
11.1 Manufacturing Processes, Material Processing, and Tolerancing 11.2 Assembly Line Balancing, Takt Time, Cycle Time, and Throughput 11.3 Sustainable Manufacturing, Waste Minimization, and Life-Cycle Assessment
12 Chapter 12: Production Planning, Inventory Control & Sequencing
12.1 Demand Forecasting Methods and Forecast Error Tracking 12.2 Aggregate Planning, Master Production Scheduling (MPS), and MRP 12.3 Deterministic Inventory Models: EOQ, EPQ, and Safety Stock 12.4 Job Sequencing, Dispatching Rules, and Flow Shop Scheduling
13 Chapter 13: Lean Systems & Theory of Constraints
13.1 Lean Foundations: Value Stream Mapping, Seven Wastes, and 5S 13.2 Pull Systems, Kanban, Just-In-Time (JIT), and SMED Setup Reduction 13.3 Theory of Constraints: Bottleneck Identification and Drum-Buffer-Rope
14 Chapter 14: Facilities Planning & Material Handling
14.1 Facility Location Analysis: Qualitative Factor Rating and Centroid Method 14.2 Facility Layout Design and Flow Analysis 14.3 Material Handling Equipment, Warehousing, and AS/RS
15 Chapter 15: Supply Chain Design & Logistics
15.1 Supply Chain Network Architecture and Transportation Modes 15.2 Distribution Strategies, Cross-Docking, and Vehicle Routing 15.3 The Bullwhip Effect, Risk Pooling, and Supply Chain Coordination
16 Chapter 16: Human Factors & Cognitive Ergonomics
16.1 Cognitive Engineering, Human-Machine Interface, Displays, and Controls 16.2 Anthropometric Principles, Percentile Design, and Biomechanical Posture 16.3 Environmental Ergonomics: Industrial Noise, Lighting, and Heat Stress
17 Chapter 17: Physical Ergonomics & Workplace Safety
17.1 Physical Ergonomics: The NIOSH Manual Lifting Equation 17.2 Cumulative Trauma Disorders and Postural Assessment 17.3 Workplace Safety: OSHA Standards, Hazard Analysis, and Control Hierarchy
18 Chapter 18: Work Design & Measurement
18.1 Methods Engineering, Process Charting, and Principles of Motion Economy 18.2 Direct Stopwatch Time Study: Observed Time, Performance Rating, and Allowances 18.3 Predetermined Time Systems, Work Sampling, and Learning Curves
19 Chapter 19: Quality Management, Six Sigma & Analytical Tools
19.1 Quality Philosophies, Total Quality Management, and Cost of Quality 19.2 Six Sigma DMAIC Methodology and Quality Function Deployment 19.3 The Seven Basic Quality Tools, Root Cause Analysis, and Taguchi Loss Function
20 Chapter 20: Statistical Process Control
20.1 Statistical Process Control Principles, Variation, and Run Rules 20.2 Variable Control Charts: X-bar & R, X-bar & S, and Individual-Moving Range 20.3 Attribute Control Charts: Defectives (p, np) and Defects (c, u)
21 Chapter 21: Process Capability & Acceptance Sampling
21.1 Process Capability Indices and Defect Levels 21.2 Acceptance Sampling Concepts and Operating Characteristic Curves 21.3 Sampling Risks, AQL, LTPD, and Standard Sampling Plans
22 Chapter 22: Systems Engineering & Life-Cycle Management
22.1 The Systems Engineering V-Model, Stakeholder Requirements, and Functional Architecture 22.2 Configuration Management, Interface Control, and Verification & Validation 22.3 Life-Cycle Costing, Maintainability, and System Availability
23 Chapter 23: Reliability Engineering & Risk Analysis
23.1 Reliability Mathematics, Hazard Rates, and the Bathtub Curve 23.2 System Reliability Configurations: Series, Parallel, and k-out-of-n Systems 23.3 Failure Modes and Effects Analysis and Fault Tree Analysis
18.1 Methods Engineering, Process Charting, and Principles of Motion Economy
Key Takeaways Explain This Topic AI
Methods engineering systematically analyzes operations to eliminate waste, improve workplace ergonomics, and standardize procedures using the seven-step engineering approach and the ECRS (Eliminate, Combine, Rearrange, Simplify) framework.
ASME standard process charting utilizes five core symbols: Operation (circle), Inspection (square), Transportation (arrow), Delay (D-shape), and Storage (inverted triangle), with combined activities represented by concentric symbols.
Worker and Machine charts calculate idle times and evaluate machine coupling using n <= (l + m) / (l + w), identifying whether a cell is machine-paced or operator-paced and determining machine interference.
Therbligs are the 17 standard fundamental micro-motions developed by Frank and Lillian Gilbreth; effective therbligs (e.g., Reach, Move, Grasp) advance work, while ineffective therbligs (e.g., Hold, Search, Select, Position) represent targets for immediate elimination.
Principles of motion economy span three domains: use of the human body (symmetrical simultaneous motions, lowest motion class, continuous curved paths), arrangement of the workplace (fixed locations, normal and maximum reach zones, gravity feed, drop delivery), and design of tools and equipment.
Last updated: September 2026
Methods engineering—originally pioneered by Frederick Winslow Taylor and Frank and Lillian Gilbreth—is the systematic branch of industrial engineering charged with designing, improving, and standardizing human work systems. It focuses on the human-machine interface, workstation kinematics, material flows, and operation sequences to eliminate waste, enhance physical safety, reduce musculoskeletal fatigue, and optimize unit production costs. On the FE Industrial and Systems exam, methods engineering is tested across qualitative charting standards, mathematical machine-operator coupling models, Therblig classifications, and the classical principles of motion economy.
1. Systematic Methods Engineering Procedure
Methods engineering follows a rigorous, closed-loop problem-solving procedure. Rather than applying intuitive or localized fixes, an industrial engineer moves through seven structured steps: The Methods Engineering Cycle
- 1. Select Project ──► High labor cost, bottleneck, high scrap, fatigue
- │
- ▼
- 2. Get & Record Facts ──► Process charts, flow diagrams, video analysis
- │
- ▼
- 3. Analyze Facts ──► Critical Examination (Why? What? Where? When? Who? How?)
- │ Apply ECRS: Eliminate, Combine, Rearrange, Simplify
- ▼
- 4. Develop Ideal Method ──► Motion economy, ergonomic layout, low-cost automation
- │
- ▼
- 5. Present & Install ──► Economic justification, SOPs, operator training
- │
- ▼
- 6. Job Standardization ──► Standard operating sheet, tooling, feeds & speeds
- │
- ▼
- 7. Follow-Up & Maintain ──► Periodic shop-floor audit to prevent regression
- The ECRS Analysis Framework
During the fact analysis stage, every recorded work element is interrogated through the ECRS hierarchy in strict sequential priority:
E — Eliminate : Can the operation, transit, or inspection be eliminated entirely? If an operation produces no customer-perceived value or if an upstream process can be redesigned to make the step redundant, elimination yields a 100% savings in labor, tooling, and space.
C — Combine : If an element cannot be eliminated, can it be combined with another operation or inspection? Combining steps (e.g., gauging a part while a machine cut proceeds, or using combination tools) reduces handling and setup steps.
R — Rearrange : Can the sequence of operations be altered to smooth workflow, balance cycle times, eliminate backtracking, or group related operations?
S — Simplify : After eliminating, combining, and rearranging, can the remaining necessary steps be made simpler? Simplification includes reducing reach distances, using gravity feed chutes, and employing clamping fixtures instead of manual holds.
2. Process Charting Symbology and ASME Standards
Process charts record operational sequences visually and quantitatively. Standardized by the American Society of Mechanical Engineers ( ASME Standard for Process Charts ), five graphical symbols represent every state an entity (material, human, or paperwork) can experience:
ASME Symbol Graphic Representation Activity Name Engineering Definition Shop-Floor Examples
Circle ◯ \bigcirc ◯ Operation A deliberate modification in physical, chemical, or geometric properties; assembly or disassembly; preparation for subsequent work. Milling a casting surface; driving a fastener; soldering a PCB lead; typing data.
Square □ \square □ Inspection Verification, examination, or comparison of an item against an established standard of quality, dimension, or quantity. Gauging bore diameter with a plug gauge; counting received tote bins; optical inspection.
Arrow ⇒ \Rightarrow ⇒ Transportation Movement of material, equipment, or an operator from one location to another (excluding local handling integral to an operation). Forklift moving pallets to warehouse; roller conveyor transit; worker walking to tool crib.
D-Shape D \text{D} D Delay A temporary, unplanned hold, queue, or bottleneck where the entity awaits the next scheduled action without formal authorization. Parts waiting in an infeed buffer; operator waiting for crane; cooling after heat treat.
Inverted Triangle ∇ \nabla ∇ Storage Controlled retention of an object under formal inventory authorization; withdrawal requires a requisition or release ticket. Raw bar stock stored in central warehouse; finished goods placed in high-bay racking.
Combined Symbol ◯ \bigcirc ◯ inside □ \square □ Combined Activity An operation and an inspection performed concurrently by the same operator at a single workstation. Turning a shaft on a lathe while inspecting finished surface finish with a profilometer.
Exam Distinction : Do not confuse Delay (D) with Storage ( ∇ \nabla ∇ ) . Delay is an unplanned queue or staging pause where material simply sits waiting for capacity. Storage is controlled, secure inventory retention where material cannot be moved without formal inventory transactions.
- 3. Macro-Level Process Charts: Flow Process Chart & Flow Diagram
- Flow Process Chart
A Flow Process Chart records the chronological sequence of all operations, inspections, transportations, delays, and storages across an entire manufacturing value stream. Charts are constructed for three distinct subjects:
Material Flow Process Chart : Tracks the physical transformations and movements of a part or raw stock.
Worker Flow Process Chart : Tracks the physical actions, tasks, and travel of an operator.
Equipment Flow Process Chart : Tracks the utilization, cutting cycles, and idle periods of a machine.
The header of every Flow Process Chart contains a Summary Table that totals the count of each symbol, cumulative transit distances (in feet or meters), and total elapsed durations (in minutes or hours). The methods engineer compares the Present Method summary against the Proposed Method summary to quantify improvements: Flow Process Chart Summary Table
- ┌─────────────────┬───────────┬────────────┬─────────────┬──────────────┐
- │ Activity Class │ Present │ Proposed │ Difference │ Savings (%) │
- ├─────────────────┼───────────┼────────────┼─────────────┼──────────────┤
- │ Operations │ 14 │ 9 │ -5 │ 35.7% │
- │ Inspections │ 4 │ 2 │ -2 │ 50.0% │
- │ Transportations │ 11 │ 4 │ -7 │ 63.6% │
- │ Delays │ 7 │ 1 │ -6 │ 85.7% │
- │ Storages │ 3 │ 2 │ -1 │ 33.3% │
- ├─────────────────┼───────────┼────────────┼─────────────┼──────────────┤
- │ Total Distance │ 840 ft │ 220 ft │ -620 ft │ 73.8% │
- │ Total Time │ 186.0 min │ 72.5 min │ -113.5 min │ 61.0% │
- └─────────────────┴───────────┴────────────┴─────────────┴──────────────┘
- Flow Diagram
A Flow Diagram is a scale drawing of the physical shop-floor layout (including walls, machinery, workstations, storage racks, and aisles) upon which the path of the material or operator is traced using lines and ASME symbols. While a Flow Process Chart shows the sequence of activities, the Flow Diagram exposes:
Long travel distances and excessive transit paths.
Backtracking (loops where parts double back over previously traversed routes).
Floor congestion and cross-traffic intersections where collisions or material handling bottlenecks occur.
Opportunities for cellular machine rearrangement (converting disconnected process layouts into compact U-shaped cells).
- 4. Micro-Level Analysis: Worker and Machine Chart & Two-Handed Process Chart
- Worker and Machine Chart (Man-Machine Chart)
A Worker and Machine Chart visualizes the synchronous relationship between an operator and one or more machines along a shared chronological time axis. It identifies idle periods and evaluates the economic feasibility of multi-machine coupling (assigning multiple machines to a single operator). Worker and Machine Time Synchronization
- Time Operator Activity Machine Activity
- (min) ┌──────────────────────────┐ ┌──────────────────────────┐
- 0.0 ───┤ Load/Unload Machine (l) │◄─────────►│ Concurrent Loading (l) │
- 1.2 ───┼──────────────────────────┤ ├──────────────────────────┤
- │ Walk to Machine 2 (w) │ │ │
- 1.6 ───┼──────────────────────────┤ │ │
- │ │ │ Machine Automatic │
- │ Operator Idle Time │ │ Run Time (m) │
- │ │ │ │
- 5.6 ───┼──────────────────────────┤ │ │
- │ Walk to Machine 1 (w) │ │ │
- 6.0 ───┴──────────────────────────┴───────────┴──────────────────────────┘
- Time Component Breakdown
Independent Operator Service Time : Tasks performed by the operator while the machine is running (e.g., retrieving raw forgings, inspecting finished parts, walking between equipment).
Concurrent Service Time / Coupling Time ( l l l ) : Tasks that require the operator and the machine to interact while the machine is stopped (e.g., loading raw blanks into a chuck, clamping fixtures, unloading finished parts).
Machine Automatic Run Time ( m m m ) : Time during which the machine operates under automated power without human intervention (e.g., automatic spindle feed, CNC milling cycle).
Operator Walk / Transit Time ( w w w ) : Time spent traversing between adjacent machines.
Operator Idle Time : Time the operator waits for a machine to complete its run.
Machine Idle Time (Machine Interference) : Time a machine sits stopped waiting for the operator to finish servicing another machine.
Mathematical Machine Coupling Model
To determine the theoretical maximum number of identical machines ( n n n ) an operator can tend without creating machine interference: n = l + m l + w n = \frac{l + m}{l + w} n = l + w l + m
Where:
- l l l = loading and unloading time (concurrent service)
- m m m = machine automatic run time
- w w w = worker transit, setup, or inspection time between machines
Because n n n is rarely an exact integer, the methods engineer must evaluate two integer options: n 1 = ⌊ n ⌋ n_1 = \lfloor n \rfloor n 1 = ⌊ n ⌋ (rounded down) versus n 2 = ⌈ n ⌉ n_2 = \lceil n \rceil n 2 = ⌈ n ⌉ (rounded up):
Under-Coupling ( n 1 = ⌊ n ⌋ n_1 = \lfloor n \rfloor n 1 = ⌊ n ⌋ ) :
Operator has sufficient time to service all machines.
Cell cycle time is machine-paced : T c = l + m T_c = l + m T c = l + m .
Machines experience zero idle time ( 0 % 0\% 0% interference).
Operator experiences idle time: T idle, op = ( l + m ) − n 1 ( l + w ) T_{\text{idle, op}} = (l + m) - n_1(l + w) T idle, op = ( l + m ) − n 1 ( l + w ) .
Over-Coupling ( n 2 = ⌈ n ⌉ n_2 = \lceil n \rceil n 2 = ⌈ n ⌉ ) :
Machines must wait for the operator to service them.
Cell cycle time is operator-paced : T c = n 2 ( l + w ) T_c = n_2(l + w) T c = n 2 ( l + w ) .
Operator experiences zero idle time.
Machines experience machine interference idle time: T idle, mach = n 2 ( l + w ) − ( l + m ) T_{\text{idle, mach}} = n_2(l + w) - (l + m) T idle, mach = n 2 ( l + w ) − ( l + m ) .
Economic Selection Rule
To select between n 1 n_1 n 1 and n 2 n_2 n 2 , compute the total cost per finished unit ( C u C_u C u ): C u = ( C o + n ⋅ C m ) ⋅ T c n C_u = \frac{(C_o + n \cdot C_m) \cdot T_c}{n} C u = n ( C o + n ⋅ C m ) ⋅ T c
Where:
- C o C_o C o = operator hourly wage ($/hr)
- C m C_m C m = machine hourly operating cost ($/hr per machine)
- T c T_c T c = cell cycle time (hours)
- n n n = number of machines assigned
Select the integer n n n that minimizes total unit cost C u C_u C u .
Two-Handed Process Chart (Operator Process Chart)
A Two-Handed Process Chart records the synchronized micro-motions of an operator's left hand (LH) and right hand (RH) against a shared vertical sequence. It is applied to highly repetitive, short-cycle manual assembly operations.
Adapted Symbols : Operation (grasping/modifying), Transportation (reaching/moving), Hold (triangle ∇ \nabla ∇ , representing a hand acting as a static clamp), and Delay (hand idle).
Primary Engineering Objective : Identify and eliminate Hold (holding a part is non-value-added and induces muscle fatigue) by introducing mechanical fixtures, clamps, or vacuum jigs; balance the workload evenly between both hands.
5. Therbligs: Fundamental Micro-Motions
Formulated by Frank and Lillian Gilbreth , Therbligs (an anagram of Gilbreth spelled backwards with 'th' transposed) are the fundamental elemental subdivisions of human physical work. The Gilbreths originally listed 18; modern methods-engineering texts standardize on the 17 below, having dropped the redundant Find (the instant of recognition at the end of Search ). Every manual job consists of combinations of these 17 micro-motions. Industrial engineers categorize Therbligs into Effective and Ineffective groups: The 17 Gilbreth Therbligs
- Effective Therbligs Ineffective Therbligs
- (Value-Adding / Direct) (Non-Value-Adding / Waste)
- ┌────────────────────────────────┐ ┌────────────────────────────────┐
- │ 1. Reach (RE) │ │ 9. Search (Sh) │
- │ 2. Move (M) │ │ 10. Select (St) │
- │ 3. Grasp (G) │ │ 11. Inspect (I) │
- │ 4. Release Load (RL) │ │ 12. Hold (H) │
- │ 5. Pre-position (PP) │ │ 13. Unavoidable Delay (UD) │
- │ 6. Use (U) │ │ 14. Avoidable Delay (AD) │
- │ 7. Assemble (A) │ │ 15. Plan (Pn) │
- │ 8. Disassemble (DA) │ │ 16. Rest for Fatigue (R) │
- └────────────────────────────────┘ │ 17. Position (P) │
- └────────────────────────────────┘
Therblig Name Abbr. Category Engineering Definition Methods Improvement Strategy
Reach RE Effective Empty hand moving toward an object; begins when hand moves, ends when contact is made. Shorten transit distance; arrange tools within normal reach envelope.
Move M Effective Hand moving an object under load; begins when part is gripped, ends when part arrives at destination. Shorten distance; utilize gravity drop chutes and momentum.
Grasp G Effective Closing fingers around an object to gain physical control. Use pick-up aids; provide vacuum grippers; present parts individually in bins.
Release Load RL Effective Letting go of an object; relinquishing muscular control. Use drop delivery chutes; eliminate manual placement at end of cycle.
Pre-position PP Effective Orienting an object in a predetermined position ready for subsequent use. Use slotted holders, guide funnels, or magnetic orienting fixtures.
Use U Effective Manipulating a tool, device, or apparatus to perform intended work. Optimize tool speeds, feeds, and mechanical leverage.
Assemble A Effective Bringing two or more mating components together. Design parts with chamfers, self-aligning pilots, or snap-fits.
Disassemble DA Effective Separating mating components. Eliminate threaded fasteners; utilize quick-release toggle clamps.
Search Sh Ineffective Eyes or hands hunting for an object; begins when eyes start moving. Eliminate completely : maintain definite, fixed locations for all items.
Select St Ineffective Choosing one object among several similar items. Store parts in separate compartmentalized bins; avoid jumbled tote trays.
Inspect I Ineffective Verifying part quality, finish, or dimensional tolerance. Integrate sensor-based Poka-Yoke fixtures; automate optical gauging.
Hold H Ineffective One hand statically supporting an object while the other works on it. Eliminate completely : replace hand with mechanical clamping fixtures or vises.
Unavoidable Delay UD Ineffective Waiting caused by process interferences outside operator control. Rebalance line cycle times; reorganize man-machine coupling.
Avoidable Delay AD Ineffective Operator idleness, deviation, or unauthorized stoppage. Improve operator training; establish standard operating procedures (SOPs).
Plan Pn Ineffective Mental hesitation or decision-making to determine next action. Standardize process sequence; provide clear visual work instructions.
Rest R Ineffective Physiological pause to overcome muscular or mental fatigue. Improve workstation ergonomics; provide adjustable seating and anti-fatigue mats.
Position P Ineffective Turning, aligning, or orienting an object at the point of use so it fits or engages correctly. Add chamfers, tapered lead-ins, and self-locating nests so the part seats itself; convert Position into Pre-position performed off the critical path.
6. Principles of Motion Economy
Originally formulated by Frank and Lillian Gilbreth and expanded by Ralph M. Barnes , the Principles of Motion Economy provide actionable engineering guidelines for designing productive, low-fatigue work environments. They are categorized into three core domains:
1. Use of the Human Body
Simultaneous and Symmetrical Motions : Both hands should begin and complete their motions at the exact same instant. Both hands should not be idle at the same time (except during authorized rest periods). Arm motions should be simultaneous and in opposite, symmetrical directions; symmetrical arm paths naturally balance biological reaction forces across the torso, minimizing postural muscle fatigue.
Five Classes of Human Motion : Hand and arm motions are classified according to the biological pivots involved. Methods must be designed to utilize the lowest feasible class (lowest energy expenditure and fastest cycle time):
Class 1 : Fingers only (e.g., keyboarding, picking miniature screws). Fastest, lowest energy.
Class 2 : Fingers and wrist (e.g., writing, turning a dial).
Class 3 : Fingers, wrist, and forearm (e.g., assembly bench work, screwdriver rotation).
Class 4 : Fingers, wrist, forearm, and upper arm (e.g., reaching across an assembly table). High energy, causes shoulder strain.
Class 5 : Entire body: trunk bending, torso twisting, shoulder flexion, walking. Highest fatigue, slowest execution. Avoid Class 5 motions through ergonomic layout .
Continuous Curved Motions : Smooth, continuous curved hand sweeps are faster and require far less physical effort than straight-line motions that incorporate sudden, abrupt changes in direction. Reversing or making sharp angle changes requires muscular deceleration to zero velocity followed by acceleration in a new direction, quadrupling energy consumption.
Momentum Utilization : Kinetic momentum should be harnessed to assist the worker whenever physical forces are needed (e.g., utilizing the momentum of a hammer swing). Conversely, muscular effort required to overcome or arrest moving loads must be minimized by providing mechanical stops or bumpers.
2. Arrangement of the Workplace
Definite and Fixed Locations : All tools, fixtures, containers, and materials must possess definite, unchanging, and visually marked locations. This develops sub-conscious muscular automaticity (motor habits), eliminating the ineffective therbligs Search (Sh), Select (St), and Plan (Pn).
Normal and Maximum Working Areas :
Normal Working Area : The comfortable horizontal boundary circumscribed by sweeping the forearm across the bench while the upper arm hangs naturally at the side (elbow remains stationary). All high-frequency components, hand tools, and assembly fixtures must reside within this zone.
Maximum Working Area : The outer horizontal boundary reached by fully extending the arm from the shoulder without bending the torso or leaning forward. Low-frequency parts, secondary tools, and finished goods drop chutes must be located within this zone. Ergonomic Horizontal Working Envelopes
- ┌───────────────────────────────────────────────┐
- │ Maximum Working Area │
- │ ┌───────────────────────────────────────┐ │
- │ │ Normal Working Area │ │
- │ │ ┌─────────────────────────┐ │ │
- │ │ │ Assembly Fixture │ │ │
- │ │ └─────────────────────────┘ │ │
- │ │ Left Hand Sweep Right Hand Sweep│ │
- │ └───────────────────────────────────────┘ │
- │ Extended Arm Reach Boundary │
- └───────────────────────────────────────────────┘
- ▲
- Operator
Gravity Feed and Drop Delivery :
Gravity Feed Bins : Bins tilted toward the operator allow parts to slide to the front pick point via gravity, presenting components at the exact same location at fingertips without requiring the operator to reach deep into a tote.
Drop Delivery : Providing a hole, chute, or conveyor directly beneath or adjacent to the assembly fixture allows the finished part to drop into a container the instant the hands release it, completely eliminating the Move (M) motion required to transport finished goods to a staging tote.
Workstation Lighting and Height : Provide glare-free illumination (minimum 50 to 100 foot-candles for medium assembly; 200+ foot-candles for fine precision work). The working surface height should sit 2 to 4 inches below the operator's resting elbow height for seated or standing assembly, and lower for heavy lifting tasks.
3. Design of Tools and Equipment
Relieve Hands with Fixtures : Hands are poor clamping devices. Always relieve the hands of static holding tasks by employing foot-operated vises, mechanical toggles, magnetic chucks, or pneumatic clamps.
Combined Tools : Combine two or more tools into a single functional unit whenever possible (e.g., combination socket and torque wrench, reversible screwdriver, hammer with nail-puller claw).
Ergonomic Tool Handles : Handles must be designed to maximize contact surface area with the palm to prevent localized pressure hotspots on the median nerve (carpal tunnel syndrome). Handles should be contoured or angled so that the wrist remains in a neutral, straight alignment, completely avoiding extreme ulnar deviation, radial deviation, flexion, or extension .
- 7. Step-by-Step Worked Engineering Calculations
- Worked Example 18.1.1: Man-Machine Allocation and Economic Analysis
Problem : An industrial engineer in an automotive machining department must configure a semi-automated manufacturing cell. An operator tends identical CNC turning machines. The operational time parameters and operating cost rates are:
Loading and unloading time (concurrent service): l = 1.2 minutes/machine l = 1.2\text{ minutes/machine} l = 1.2 minutes/machine
Machine automatic cutting time: m = 4.8 minutes/machine m = 4.8\text{ minutes/machine} m = 4.8 minutes/machine
Operator walking and inspection time between machines: w = 0.4 minutes/machine w = 0.4\text{ minutes/machine} w = 0.4 minutes/machine
Operator labor wage rate: C o = $ 24.00 / hour = $ 0.40 / minute C_o = \text{\textdollar}24.00/\text{hour} = \text{\textdollar}0.40/\text{minute} C o = $ 24.00/ hour = $ 0.40/ minute
Machine operating rate (per machine): C m = $ 36.00 / hour = $ 0.60 / minute C_m = \text{\textdollar}36.00/\text{hour} = \text{\textdollar}0.60/\text{minute} C m = $ 36.00/ hour = $ 0.60/ minute
Calculate the theoretical number of machines ( n n n ) an operator can tend without idle machine interference.
Evaluate cell cycle time, operator idle time, machine idle time, and hourly production rate for both under-coupling ( n 1 = ⌊ n ⌋ n_1 = \lfloor n \rfloor n 1 = ⌊ n ⌋ ) and over-coupling ( n 2 = ⌈ n ⌉ n_2 = \lceil n \rceil n 2 = ⌈ n ⌉ ).
Calculate the total unit production cost ( C u C_u C u ) for both configurations and select the economically optimal machine allocation.
Solution :
Step 1: Compute Theoretical Machine Allocation ( n n n ) n = l + m l + w = 1.2 + 4.8 1.2 + 0.4 = 6.0 minutes 1.6 minutes = 3.75 machines n = \frac{l + m}{l + w} = \frac{1.2 + 4.8}{1.2 + 0.4} = \frac{6.0\text{ minutes}}{1.6\text{ minutes}} = 3.75\text{ machines} n = l + w l + m = 1.2 + 0.4 1.2 + 4.8 = 1.6 minutes 6.0 minutes = 3.75 machines
Because n = 3.75 n = 3.75 n = 3.75 , the engineer must evaluate assigning either n 1 = 3 n_1 = 3 n 1 = 3 machines or n 2 = 4 n_2 = 4 n 2 = 4 machines.
Step 2: Operational Evaluation of n 1 = 3 n_1 = 3 n 1 = 3 Machines (Under-Coupling)
Cell Cycle Time: Because n 1 ( l + w ) = 3 × 1.6 = 4.8 min < 6.0 min n_1 (l + w) = 3 \times 1.6 = 4.8\text{ min} < 6.0\text{ min} n 1 ( l + w ) = 3 × 1.6 = 4.8 min < 6.0 min , the cell is machine-paced : T c = l + m = 1.2 + 4.8 = 6.0 minutes T_c = l + m = 1.2 + 4.8 = 6.0\text{ minutes} T c = l + m = 1.2 + 4.8 = 6.0 minutes
Operator Work Time in Cycle: 3 × ( l + w ) = 3 × 1.6 = 4.8 minutes 3 \times (l + w) = 3 \times 1.6 = 4.8\text{ minutes} 3 × ( l + w ) = 3 × 1.6 = 4.8 minutes
Operator Idle Time per Cycle: T idle, op = 6.0 − 4.8 = 1.2 minutes T_{\text{idle, op}} = 6.0 - 4.8 = 1.2\text{ minutes} T idle, op = 6.0 − 4.8 = 1.2 minutes
Machine Idle Time per Cycle (Machine Interference): T idle, mach = 0.0 minutes T_{\text{idle, mach}} = 0.0\text{ minutes} T idle, mach = 0.0 minutes ( 0 % 0\% 0% interference; machines run continuously)
Production Rate: 3 parts are completed every 6.0 minutes: Rate 3 = 3 parts 6.0 min × 60 min/hr = 30.0 parts/hour \text{Rate}_3 = \frac{3\text{ parts}}{6.0\text{ min}} \times 60\text{ min/hr} = 30.0\text{ parts/hour} Rate 3 = 6.0 min 3 parts × 60 min/hr = 30.0 parts/hour
Step 3: Operational Evaluation of n 2 = 4 n_2 = 4 n 2 = 4 Machines (Over-Coupling)
Cell Cycle Time: Because n 2 ( l + w ) = 4 × 1.6 = 6.4 min > 6.0 min n_2 (l + w) = 4 \times 1.6 = 6.4\text{ min} > 6.0\text{ min} n 2 ( l + w ) = 4 × 1.6 = 6.4 min > 6.0 min , the cell is operator-paced : T c = n 2 ( l + w ) = 4 × 1.6 = 6.4 minutes T_c = n_2(l + w) = 4 \times 1.6 = 6.4\text{ minutes} T c = n 2 ( l + w ) = 4 × 1.6 = 6.4 minutes
Operator Work Time in Cycle: 4 × 1.6 = 6.4 minutes 4 \times 1.6 = 6.4\text{ minutes} 4 × 1.6 = 6.4 minutes
Operator Idle Time per Cycle: T idle, op = 0.0 minutes T_{\text{idle, op}} = 0.0\text{ minutes} T idle, op = 0.0 minutes (operator is fully utilized)
Machine Idle Time per Cycle (Machine Interference): T idle, mach = T c − ( l + m ) = 6.4 − 6.0 = 0.4 minutes per machine T_{\text{idle, mach}} = T_c - (l + m) = 6.4 - 6.0 = 0.4\text{ minutes per machine} T idle, mach = T c − ( l + m ) = 6.4 − 6.0 = 0.4 minutes per machine
Machine Interference Percentage: 0.4 min 6.4 min × 100 % = 6.25 % \frac{0.4\text{ min}}{6.4\text{ min}} \times 100\% = 6.25\% 6.4 min 0.4 min × 100% = 6.25%
Production Rate: 4 parts are completed every 6.4 minutes: Rate 4 = 4 parts 6.4 min × 60 min/hr = 37.5 parts/hour \text{Rate}_4 = \frac{4\text{ parts}}{6.4\text{ min}} \times 60\text{ min/hr} = 37.5\text{ parts/hour} Rate 4 = 6.4 min 4 parts × 60 min/hr = 37.5 parts/hour
Step 4: Economic Unit Cost Comparison
For n 1 = 3 n_1 = 3 n 1 = 3 machines: Cost per cycle = ( C o + 3 ⋅ C m ) ⋅ T c = ( $ 0.40 + 3 × $ 0.60 ) × 6.0 = ( $ 0.40 + $ 1.80 ) × 6.0 = $ 2.20 × 6.0 = $ 13.20 \text{Cost per cycle} = (C_o + 3 \cdot C_m) \cdot T_c = (\$0.40 + 3 \times \$0.60) \times 6.0 = (\$0.40 + \$1.80) \times 6.0 = \$2.20 \times 6.0 = \$13.20 Cost per cycle = ( C o + 3 ⋅ C m ) ⋅ T c = ( $0.40 + 3 × $0.60 ) × 6.0 = ( $0.40 + $1.80 ) × 6.0 = $2.20 × 6.0 = $13.20 C u , 3 = $ 13.20 3 parts = $ 4.40 per part C_{u, 3} = \frac{\$13.20}{3\text{ parts}} = \$4.40\text{ per part} C u , 3 = 3 parts $13.20 = $4.40 per part
For n 2 = 4 n_2 = 4 n 2 = 4 machines: Cost per cycle = ( C o + 4 ⋅ C m ) ⋅ T c = ( $ 0.40 + 4 × $ 0.60 ) × 6.4 = ( $ 0.40 + $ 2.40 ) × 6.4 = $ 2.80 × 6.4 = $ 17.92 \text{Cost per cycle} = (C_o + 4 \cdot C_m) \cdot T_c = (\$0.40 + 4 \times \$0.60) \times 6.4 = (\$0.40 + \$2.40) \times 6.4 = \$2.80 \times 6.4 = \$17.92 Cost per cycle = ( C o + 4 ⋅ C m ) ⋅ T c = ( $0.40 + 4 × $0.60 ) × 6.4 = ( $0.40 + $2.40 ) × 6.4 = $2.80 × 6.4 = $17.92 C u , 4 = $ 17.92 4 parts = $ 4.48 per part C_{u, 4} = \frac{\$17.92}{4\text{ parts}} = \$4.48\text{ per part} C u , 4 = 4 parts $17.92 = $4.48 per part
Step 5: Engineering Conclusion Assigning 3 machines yields a unit manufacturing cost of $4.40/part , compared to $4.48/part when assigning 4 machines. Even though assigning 4 machines yields higher gross hourly volume (37.5 parts/hr vs. 30.0 parts/hr), the machine interference idle time (0.4 min/cycle) on expensive machine capital outweighs the labor utilization gain. Unless the plant is capacity-constrained and willing to pay an 8-cent per part penalty for extra throughput, n = 3 n = 3 n = 3 is the economically optimal allocation .
8. NCEES Reference Handbook Tips & Realistic Exam Traps
ASME Symbol Confusion : On conceptual exam questions, examinees frequently confuse the Delay (D-shape) and Storage (inverted triangle ∇ \nabla ∇ ) symbols. Remember: if material sits in an aisle or bin waiting for the next machine, it is a Delay . Material is in Storage only if it is housed under formal inventory custody where a requisition, receipt, or ERP transaction is required to withdraw it.
Hold is Ineffective : On Therblig classification questions, students frequently assume Hold (H) is an effective assembly motion. Hold is strictly ineffective . Holding a workpiece statically with one hand generates static muscle ischemia and robs that hand of productive work. Eliminate Hold using mechanical clamps.
Motion Class Inversion : Motion classes rank from 1 to 5 based on physical pivots. Class 1 is fingers only; Class 5 is entire body/bending. Do not invert these! Lowest class (Class 1) is fastest, most accurate, and consumes the least energy.
Cycle Time in Man-Machine Charts : Never assume that cell cycle time is always l + m l + m l + m . If the operator is overloaded ( n ( l + w ) > l + m n(l + w) > l + m n ( l + w ) > l + m ), the cycle time stretches to n ( l + w ) n(l + w) n ( l + w ) , and machines experience idle interference!