Study guide

Beams, Deflection, Columns, Mohr's Circle, and Combined Loading

FE Mechanical Study Guide Exam

Track your progress as you read

Finished sections get a check mark.

1 FE Mechanical Exam Map, Handbook, and Strategy

1.1 Official NCEES FE Mechanical Facts 1.2 Scoring, Attempts, Fees, and State Board Context 1.3 Reference Handbook Search, Units, and Calculator Workflow 1.4 Official Content Specification and Study Allocation 1.5 Pacing, Flagging, and Error Classification 1.6 How FE Mechanical Questions Test Model Selection

2 Math, Economics, Ethics, and Tools

Calculus, Differential Equations, and Linear Algebra Review Numerical Methods, Vectors, and Engineering Models Probability, Statistics, and Uncertainty Engineering Economics, Cash Flow, and Decision Methods Ethics, Professional Practice, and Public Welfare Calculator Workflows, Algebra, and Unit Checks

3 Mechanics Core

Statics: Free-Body Diagrams and Equilibrium Trusses, Frames, Centroids, and Friction Dynamics: Kinematics, Newton's Laws, and Relative Motion Work, Energy, Impulse, Momentum, Rotation, and Vibration Mechanics of Materials: Stress, Strain, and Torsion Beams, Deflection, Columns, Mohr's Circle, and Combined Loading

4 Thermal-Fluids Core

Fluid Properties, Statics, and Dimensional Analysis Bernoulli, Energy Equation, Pipe Losses, and Pumps Momentum Control Volumes and Turbomachinery Thermodynamic Properties, Energy Balances, and Ideal Gases Power, Refrigeration Cycles, Psychrometrics, and Second Law Heat Transfer: Conduction, Convection, Radiation, and Heat Exchangers

5 Systems, Design, and Final Readiness

5.1 Materials Processing, Failure, and Selection 5.2 Measurements, Instrumentation, Sensors, Circuits, and Uncertainty 5.3 Controls, Transfer Functions, Response, and Feedback 5.4 Mechanical Design: Shafts, Bearings, Gears, Springs, and Fasteners 5.5 Pressure Vessels, Welds, Fatigue, GD&T, and Design Safety 5.6 Final Mixed Practice, Readiness, and Exam-Day Plan

6 Integrated FE Mechanical Practice

Mixed Mechanics and Materials Practice Thermal-Fluid Design and Energy Cases Controls, Instrumentation, and Uncertainty Cases Mechanical Design Failure Mode Cases Full-Exam Simulation, Review, and Remediation Last-Week Handbook, Units, and Calculator Drills

Beams, Deflection, Columns, Mohr's Circle, and Combined Loading

Key Takeaways Explain This Topic AI

Bending stress σ = Mc/I; maximum at the extreme fiber distance c from the neutral axis.

Transverse shear stress τ = VQ/(Ib); load, shear, and moment relate by dV/dx = −w, dM/dx = V.

Max deflection of a simply supported beam with central load P is PL³/(48EI).

Euler buckling: P_cr = π²EI/(KL)²; K = 1 pinned-pinned, 0.5 fixed-fixed, 2 fixed-free.

Mohr's circle: center (σ_x+σ_y)/2, radius √[((σ_x−σ_y)/2)² + τ_xy²] gives principal stresses and τ_max.

Last updated: June 2026

Beam bending and shear

A transverse load on a beam creates internal shear V and bending moment M . They are linked to the distributed load w by the Handbook relations dV/dx = −w(x) and dM/dx = V(x), so moment is the area under the shear diagram and shear is the area under the load diagram. Maximum moment occurs where shear crosses zero — the fastest way to locate it on a shear diagram.

The flexure (bending) stress formula gives normal stress that varies linearly across the depth: σ = M c I \sigma = \frac{M c}{I} σ = I M c ​

where c is the distance from the neutral (centroidal) axis to the extreme fiber and I is the area moment of inertia of the cross-section. The section modulus S = I/c packages this as σ_max = M/S. Transverse shear stress is τ = V Q I b \tau = \frac{VQ}{I b} τ = I b V Q ​

with Q the first moment of the area above (or below) the point and b the width there. For a rectangular section, τ peaks at the neutral axis at 1.5 V/A — 50% higher than the average shear V/A, a frequent FE distinction.

Worked example: a simply supported beam, length 4 m, central point load 12 kN. Max moment at center M = PL/4 = 12(4)/4 = 12 kN·m. For a 50 mm × 150 mm rectangle (tall), I = bh³/12 = (0.05)(0.15)³/12 = 1.406×10⁻⁵ m⁴, c = 0.075 m. σ_max = Mc/I = 12 000(0.075)/1.406×10⁻⁵ = 64.0 MPa.

Beam deflection

Deflection comes from EI y'' = M(x) (the elastic curve), but FE expects you to use tabulated formulas from the Handbook rather than integrate. Memorize the few highest-yield cases:

  • Loading (simply supported unless noted) Max deflection
  • Central point load P PL³/(48EI)
  • Uniform load w (total wL) 5wL⁴/(384EI)
  • Cantilever, end point load P PL³/(3EI)
  • Cantilever, uniform load w wL⁴/(8EI)

Stiffer (larger EI) or shorter beams deflect less; deflection scales with L³ or L⁴, so doubling span increases deflection 8× or 16×.

Column buckling

Long slender columns fail by elastic buckling below the yield stress. Euler's formula gives the critical load: P c r = π 2 E I ( K L ) 2 P_{cr} = \frac{\pi^2 E I}{(KL)^2} P cr ​ = ( K L ) 2 π 2 E I ​

KL is the effective length , and K depends on end conditions: K = 1 pinned-pinned, K = 0.5 fixed-fixed, K = 0.7 fixed-pinned, and K = 2 fixed-free (cantilever column). Use the smallest I (weak axis) because the column buckles about the axis of least resistance. The critical stress is σ_cr = P_cr/A = π²E/(KL/r)², where r = √(I/A) is the radius of gyration and KL/r is the slenderness ratio . Euler's equation is valid only above a transition slenderness; below it, columns fail by yielding/crushing, so check σ_cr against S_y.

Worked example: a 3 m pinned-pinned steel column (E = 200 GPa, I = 4×10⁻⁶ m⁴). P_cr = π²(200×10⁹)(4×10⁻⁶)/(1·3)² = 7.90×10⁶/9 = 877 kN. Fix both ends (K = 0.5) and the same column carries 4× more: 3.51 MN.

Mohr's circle and combined loading

For a plane stress state (σ_x, σ_y, τ_xy), the principal stresses and maximum shear come from the transformation equations, neatly captured by Mohr's circle : σ a v g = σ x + σ y 2 , R = ( σ x − σ y 2 ) 2 + τ x y 2 \sigma_{avg} = \frac{\sigma_x + \sigma_y}{2}, \qquad R = \sqrt{\left(\frac{\sigma_x - \sigma_y}{2}\right)^2 + \tau_{xy}^2} σ a vg ​ = 2 σ x ​ + σ y ​ ​ , R = ( 2 σ x ​ − σ y ​ ​ ) 2 + τ x y 2 ​ ​ σ 1 , 2 = σ a v g ± R , τ m a x = R \sigma_{1,2} = \sigma_{avg} \pm R, \qquad \tau_{max} = R σ 1 , 2 ​ = σ a vg ​ ± R , τ ma x ​ = R

The circle's center sits on the σ-axis at σ_avg; its radius R is the in-plane maximum shear stress. Worked example: σ_x = 80 MPa, σ_y = 20 MPa, τ_xy = 30 MPa. σ_avg = 50; R = √(30² + 30²) = 42.4 MPa. σ₁ = 92.4 MPa, σ₂ = 7.6 MPa, τ_max = 42.4 MPa. Combined loading superposes axial (P/A), bending (Mc/I), and torsional (Tr/J) stresses at a point, then feeds the resulting σ_x, σ_y, τ_xy into Mohr's circle to get the true principal stress used in a failure check — the capstone integration of the whole mechanics-of-materials chain.

Shear and moment diagrams in practice

Building shear (V) and bending-moment (M) diagrams is a high-yield FE skill. Start at one end with the support reaction, step along the beam, and add/subtract loads: a point load causes a vertical jump in V; a uniform load makes V slope linearly (dV/dx = −w); the M-diagram slope equals V (dM/dx = V), so M is the running area under the V-diagram. A point load gives a triangular M-diagram peaking under the load; a uniform load gives a parabolic M-diagram peaking at midspan. For a simply supported beam with central load P, V steps from +P/2 to −P/2 at center and M peaks at PL/4. For a full-span uniform load w, M_max = wL²/8 at midspan.

Locating M_max where V = 0 is the fastest route to the bending-stress check.

Failure theories for combined stress

Once principal stresses are known, FE tests two ductile-failure criteria. The maximum-shear-stress (Tresca) theory predicts yield when τ_max = S_y/2, i.e. (σ₁ − σ₃) reaches S_y. The distortion-energy (von Mises) theory uses the von Mises stress σ' = √(σ₁² − σ₁σ₂ + σ₂²) for plane stress, predicting yield when σ' = S_y; it is less conservative and generally more accurate for ductile metals.

  • Theory Yield criterion Use for
  • Maximum shear (Tresca) σ₁ − σ₃ = S_y Ductile, conservative
  • Distortion energy (von Mises) σ' = S_y Ductile, most accurate
  • Maximum normal stress σ₁ = S_u Brittle materials

For the earlier state σ₁ = 92.4, σ₂ = 7.6 MPa, von Mises gives σ' = √(92.4² − 92.4·7.6 + 7.6²) = 88.9 MPa, so a material with S_y = 250 MPa carries FS = 250/88.9 = 2.8. Combining a combined-loading stress state with a failure theory and a factor of safety is the complete FE design-check sequence — and the reason this chapter's topics are so heavily interlinked.