Study guide

9.6 Dynamic Friction and Vibrations: Natural Frequency and Damping

FE Other Disciplines Fundamentals of Engineering

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Strategy

About the FE Other Disciplines Exam How to Use This Study Guide

2 Chapter 1: Mathematics

1.1 Analytic Geometry, Trigonometry, and Vector Operations 1.2 Differential and Integral Calculus 1.3 Ordinary Differential Equations and Laplace Transforms 1.4 Linear Algebra, Matrices, and Systems of Equations 1.5 Numerical Methods, Root-Finding, and Numerical Integration

3 Chapter 2: Probability and Statistics

2.1 Probability Distributions, PMFs, and PDFs 2.2 Expected Value, Mean, Variance, and Descriptive Statistics 2.3 Estimation, Confidence Intervals, and Sample Sizes 2.4 Hypothesis Testing, Goodness of Fit, and Linear Regression

4 Chapter 3: Chemistry

3.1 Stoichiometry, Chemical Reactions, and Solutions 3.2 Chemical Equilibrium, Acids/Bases, and Ideal Gas Laws 3.3 Oxidation-Reduction, Electrochemistry, and Corrosion Basics

5 Chapter 4: Instrumentation and Controls

4.1 Sensors, Transducers, and Signal Conditioning 4.2 Data Sampling, Accuracy/Precision, and A/D Conversion 4.3 Logic Diagrams, Boolean Algebra, and Control Logic

6 Chapter 5: Engineering Ethics and Societal Impacts

5.1 NCEES Model Rules of Professional Conduct and Codes of Ethics 5.2 Public Protection, Licensure Boards, and Professional Liability 5.3 Societal Impacts: Sustainability, Life-Cycle Analysis, and Public Safety

7 Chapter 6: Safety, Health, and Environment

6.1 OSHA Regulations, Industrial Hygiene, and PPE 6.2 Hazard Assessment, Risk Management, and Environmental Rules 6.3 Gas Detection and Monitoring 6.4 Electrical Safety 6.5 Confined Space Entry and Ventilation Rates

8 Chapter 7: Engineering Economics

7.1 Time Value of Money, Interest Formulas, and Cash Flow Diagrams 7.2 Capital Budgeting: Present Worth, Annual Worth, IRR, and B/C Ratio 7.3 Depreciation Methods, Income Taxes, and Breakeven Analysis 7.4 Cost Analysis, Uncertainty, Expected Value, and Decision Trees

9 Chapter 8: Statics

8.1 Statics Equilibrium, Free-Body Diagrams, and Force Systems 8.2 Distributed Loads, Resultants, and Equivalent Force-Couple Systems 8.3 Internal Forces in Rigid Bodies: Trusses, Frames, Machines, and Friction 8.4 Three-Dimensional Equilibrium, Cables, and Pulley Systems 8.5 Area Properties: Centroids, Moments of Inertia, and Radius of Gyration 8.6 Weight, Mass, and Force Units: slug, lbm, lbf, and g_c

10 Chapter 9: Dynamics

9.1 Kinematics of Particles and Rigid Bodies 9.2 Newton's Second Law for Particles and Rigid Bodies 9.3 Angular Motion, Torque, and Mass Moment of Inertia 9.4 Work-Energy Principle, Power, and Efficiency 9.5 Impulse-Momentum, Impact, and Coefficient of Restitution 9.6 Dynamic Friction and Vibrations: Natural Frequency and Damping

11 Chapter 10: Strength of Materials

10.1 Stress Types, Axial Stress-Strain, and Thermal Deformation 10.2 Torsion of Circular Shafts, Polar Moment, and Angle of Twist 10.3 Shear and Moment Diagrams 10.4 Flexural Bending Stress and Transverse Shear Stress 10.5 Stress Transformations, Principal Stresses, and Mohr's Circle 10.6 Beam Deflections and Combined Axial/Bending Loading 10.7 Column Buckling (Euler Formula) and Yield/Failure Criteria

12 Chapter 11: Materials

11.1 Crystal Structure, Phase Diagrams, and Material Processing 11.2 Mechanical Properties, Fatigue, Fracture, and Corrosion 11.3 Thermal Properties of Materials 11.4 Electrical and Chemical Properties of Materials 11.5 Material Selection for Engineering Design

13 Chapter 12: Fluid Mechanics

12.1 Fluid Properties, Hydrostatic Pressure, and Manometry 12.2 Dimensionless Numbers and Flow Regimes 12.3 Continuity Equation, Bernoulli Equation, and Energy Equation 12.4 Impulse-Momentum Equation and Forces on Control Volumes 12.5 Flow in Pipes, Friction Factors (Moody Diagram), and Head Losses 12.6 Turbomachinery: Pumps, Turbines, Fans, and Compressors 12.7 Open-Channel Flow, Manning's Equation, and Drag 12.8 Fluid Transport Systems and Flow Measurement 12.9 Ideal Gas Law, Gas Mixtures, and the Real Gas Law

14 Chapter 13: Basic Electrical Engineering

13.1 Electrical Fundamentals, Ohm's Law, and DC Circuits 13.2 AC Circuits, Phasors, Impedance, and Three-Phase Power 13.3 Magnetic Fields, Induction, Transformers, and Motor Efficiency 13.4 Electrical Measuring Devices: Voltmeter, Ammeter, and Wattmeter

15 Chapter 14: Thermodynamics and Heat Transfer

14.1 First & Second Laws of Thermodynamics and Pure Substance Properties 14.2 Thermodynamic Processes and Property Diagrams (T-s, P-h, P-v) 14.3 Heat Transfer: Conduction, Convection, and Radiation 14.4 Ideal Gas Processes and Power/Refrigeration Cycles 14.5 Mass and Energy Balances on Control Volumes 14.6 Combustion and Combustion Products 14.7 Psychrometrics: Relative Humidity, Wet-Bulb Temperature, and the Psychrometric Chart

9.6 Dynamic Friction and Vibrations: Natural Frequency and Damping

Key Takeaways Explain This Topic AI

NCEES lists dynamic friction and vibrations, naming natural frequency explicitly, as the final two Dynamics sub-topics.

Kinetic friction is mu_k times the normal force, acts opposite the relative sliding velocity, and is independent of contact area and sliding speed.

Kinetic friction is always less than the maximum static friction, which is why a block accelerates once it breaks free.

The undamped natural frequency of a mass-spring system is the square root of k over m in rad/s, and dividing by 2 pi converts it to hertz.

For a simple pendulum the natural frequency is the square root of g over L and is independent of the mass.

Last updated: August 2026

9.6 Dynamic Friction and Vibrations: Natural Frequency and Damping

These are the last two sub-topics in the NCEES Dynamics list — "Dynamic friction" and "Vibrations (e.g., natural frequency)" — and vibrations is the one candidates most often reach the exam without having studied. It is a small, highly formulaic topic: three or four equations cover almost everything asked.

  • Dynamic (Kinetic) Friction
  • Once sliding begins, the friction force is: F k = μ k N F_k = \mu_k N F k ​ = μ k ​ N

Three properties, all tested as conceptual items:

Independent of contact area. Doubling the footprint does not change the friction force, because the real contact area at asperities is set by the load, not the apparent area.

Independent of sliding speed (in the classical Coulomb model).

Always opposes relative sliding velocity — its direction is set by the motion, not by the applied force.

Static vs. Kinetic μ k < μ s typically μ k ≈ 0.7 – 0.8 μ s \mu_k < \mu_s \qquad\text{typically } \mu_k \approx 0.7\text{–}0.8\,\mu_s μ k ​ < μ s ​ typically μ k ​ ≈ 0.7 – 0.8 μ s ​

This inequality has a directly observable consequence: a block on the verge of sliding needs a force μ s N \mu_s N μ s ​ N to break free, but once moving it needs only μ k N \mu_k N μ k ​ N to keep going, so the surplus accelerates it. This is the "stick-slip" jerk of a dragged object and the reason antilock braking exists — a rolling tire uses the larger μ s \mu_s μ s ​ , while a locked skidding tire is stuck with the smaller μ k \mu_k μ k ​ and stops in a longer distance.

  • Surface pair μ s \mu_s μ s ​ μ k \mu_k μ k ​
  • Steel on steel (dry) 0.74 0.57
  • Steel on steel (lubricated) 0.15 0.09
  • Rubber on dry concrete 1.0 0.8
  • Rubber on wet concrete 0.7 0.5
  • Teflon on steel 0.04 0.04
  • Worked Example: Skidding Stop Distance

A vehicle at 25 m/s locks its brakes on a road with μ k = 0.62 \mu_k = 0.62 μ k ​ = 0.62 . Find the stopping distance. a = − μ k g = − 0.62 ( 9.81 ) = − 6.08 m/s 2 a = -\mu_k g = -0.62(9.81) = -6.08\ \text{m/s}^2 a = − μ k ​ g = − 0.62 ( 9.81 ) = − 6.08 m/s 2 v 2 = v 0 2 + 2 a s ⇒ 0 = ( 25 ) 2 + 2 ( − 6.08 ) s v^2 = v_0^2 + 2as \;\Rightarrow\; 0 = (25)^2 + 2(-6.08)s v 2 = v 0 2 ​ + 2 a s ⇒ 0 = ( 25 ) 2 + 2 ( − 6.08 ) s s = 625 12.16 = 51.4 m s = \frac{625}{12.16} = \boxed{51.4\ \text{m}} s = 12.16 625 ​ = 51.4 m ​

Mass does not appear — friction force scales with weight and so does inertia, so they cancel. Note also that s ∝ v 2 s \propto v^2 s ∝ v 2 : doubling speed quadruples stopping distance, to 206 m.

Springs in Series and Parallel

Getting the equivalent stiffness right precedes every natural-frequency calculation, and the rule is the opposite of resistors: Parallel (side by side, share the load): k e q = k 1 + k 2 \text{Parallel (side by side, share the load): } k_{eq} = k_1 + k_2 Parallel (side by side, share the load): k e q ​ = k 1 ​ + k 2 ​ Series (end to end, share the deflection): 1 k e q = 1 k 1 + 1 k 2 \text{Series (end to end, share the deflection): } \frac{1}{k_{eq}} = \frac{1}{k_1} + \frac{1}{k_2} Series (end to end, share the deflection): k e q ​ 1 ​ = k 1 ​ 1 ​ + k 2 ​ 1 ​

Physical check: springs in series are softer than either one alone (each stretches), while springs in parallel are stiffer . Two 100 N/m springs give 200 N/m in parallel and 50 N/m in series.

Undamped Free Vibration

The equation of motion m x ¨ + k x = 0 m\ddot{x} + kx = 0 m x ¨ + k x = 0 yields simple harmonic motion at the natural frequency : ω n = k m [ rad/s ] , f n = ω n 2 π [ Hz ] , τ = 1 f n = 2 π m k \omega_n = \sqrt{\frac{k}{m}}\ \ [\text{rad/s}], \qquad f_n = \frac{\omega_n}{2\pi}\ \ [\text{Hz}], \qquad \tau = \frac{1}{f_n} = 2\pi\sqrt{\frac{m}{k}} ω n ​ = m k ​ ​ [ rad/s ] , f n ​ = 2 π ω n ​ ​ [ Hz ] , τ = f n ​ 1 ​ = 2 π k m ​ ​ x ( t ) = A sin ⁡ ( ω n t + ϕ ) x(t) = A\sin(\omega_n t + \phi) x ( t ) = A sin ( ω n ​ t + ϕ )

  • System Natural frequency ω n \omega_n ω n ​
  • Mass–spring (translational) k / m \sqrt{k/m} k / m ​
  • Simple pendulum , length L L L g / L \sqrt{g/L} g / L ​ — independent of mass
  • Torsional, stiffness k t k_t k t ​ , inertia I I I k t / I \sqrt{k_t/I} k t ​ / I ​
  • Mass on a beam with static deflection δ \delta δ g / δ \sqrt{g/\delta} g / δ ​
  • Compound pendulum, I O I_O I O ​ about pivot, d d d to mass center m g d / I O \sqrt{mgd/I_O} m g d / I O ​ ​

The static-deflection shortcut is worth memorizing: since k = m g / δ k = mg/\delta k = m g / δ for a spring or beam sagging δ \delta δ under its own load, ω n = g / δ \omega_n = \sqrt{g/\delta} ω n ​ = g / δ ​ . Measure the sag and you have the natural frequency without ever knowing k k k or m m m separately. A floor deflecting 5 mm under load has ω n = 9.81 / 0.005 = 44.3 \omega_n = \sqrt{9.81/0.005} = 44.3 ω n ​ = 9.81/0.005 ​ = 44.3 rad/s = 7.1 Hz — uncomfortably close to the 2–4 Hz range of walking harmonics, which is why floor vibration is a serviceability check.

Damped and Forced Vibration m x ¨ + c x ˙ + k x = F 0 sin ⁡ ω t m\ddot{x} + c\dot{x} + kx = F_0\sin\omega t m x ¨ + c x ˙ + k x = F 0 ​ sin ω t ζ = c 2 k m = c 2 m ω n , ω d = ω n 1 − ζ 2 \zeta = \frac{c}{2\sqrt{km}} = \frac{c}{2m\omega_n}, \qquad \omega_d = \omega_n\sqrt{1-\zeta^2} ζ = 2 km ​ c ​ = 2 m ω n ​ c ​ , ω d ​ = ω n ​ 1 − ζ 2 ​

  • ζ \zeta ζ Regime Behavior
  • 0 0 0 Undamped Constant-amplitude oscillation forever
  • 0 < ζ < 1 0 < \zeta < 1 0 < ζ < 1 Underdamped Decaying oscillation at ω d \omega_d ω d ​
  • 1 1 1 Critically damped Fastest return with no overshoot
  • > 1 > 1 > 1 Overdamped Slow return, no oscillation

Because ω d = ω n 1 − ζ 2 \omega_d = \omega_n\sqrt{1-\zeta^2} ω d ​ = ω n ​ 1 − ζ 2 ​ , light damping barely shifts the frequency: at ζ = 0.05 \zeta = 0.05 ζ = 0.05 (typical for a steel structure), ω d = 0.9987 ω n \omega_d = 0.9987\,\omega_n ω d ​ = 0.9987 ω n ​ . For lightly damped systems you may use ω n \omega_n ω n ​ for ω d \omega_d ω d ​ , which is why the undamped formula is so widely applicable.

Resonance

When the forcing frequency approaches ω n \omega_n ω n ​ , the amplitude is amplified by: M F = 1 [ 1 − ( ω / ω n ) 2 ] 2 + [ 2 ζ ( ω / ω n ) ] 2 MF = \frac{1}{\sqrt{\left[1-(\omega/\omega_n)^2\right]^2 + \left[2\zeta(\omega/\omega_n)\right]^2}} MF = [ 1 − ( ω / ω n ​ ) 2 ] 2 + [ 2 ζ ( ω / ω n ​ ) ] 2 ​ 1 ​

At ω = ω n \omega = \omega_n ω = ω n ​ this reduces to M F = 1 / ( 2 ζ ) MF = 1/(2\zeta) MF = 1/ ( 2 ζ ) . With ζ = 0.02 \zeta = 0.02 ζ = 0.02 , the amplification is 25× — which is why resonance destroys machines and why the standard remedies are to shift ω n \omega_n ω n ​ (change mass or stiffness), avoid the forcing frequency, or add damping.

Worked Example: Natural Frequency and Damping

A 40 kg machine sits on two identical parallel springs, each k = 5,000 k = 5{,}000 k = 5 , 000 N/m, with a damper c = 180 c = 180 c = 180 N·s/m. Find ω n \omega_n ω n ​ , f n f_n f n ​ , ζ \zeta ζ , and ω d \omega_d ω d ​ .

Equivalent stiffness (parallel): k e q = 5,000 + 5,000 = 10,000 N/m k_{eq} = 5{,}000 + 5{,}000 = 10{,}000\ \text{N/m} k e q ​ = 5 , 000 + 5 , 000 = 10 , 000 N/m

Natural frequency: ω n = 10,000 40 = 250 = 15.81 rad/s , f n = 15.81 2 π = 2.52 Hz \omega_n = \sqrt{\frac{10{,}000}{40}} = \sqrt{250} = 15.81\ \text{rad/s}, \qquad f_n = \frac{15.81}{2\pi} = \boxed{2.52\ \text{Hz}} ω n ​ = 40 10 , 000 ​ ​ = 250 ​ = 15.81 rad/s , f n ​ = 2 π 15.81 ​ = 2.52 Hz ​

Damping ratio: ζ = c 2 k m = 180 2 ( 10,000 ) ( 40 ) = 180 2 400,000 = 180 2 ( 632.5 ) = 0.142 \zeta = \frac{c}{2\sqrt{km}} = \frac{180}{2\sqrt{(10{,}000)(40)}} = \frac{180}{2\sqrt{400{,}000}} = \frac{180}{2(632.5)} = \boxed{0.142} ζ = 2 km ​ c ​ = 2 ( 10 , 000 ) ( 40 ) ​ 180 ​ = 2 400 , 000 ​ 180 ​ = 2 ( 632.5 ) 180 ​ = 0.142 ​

Underdamped, as most machinery mounts are.

Damped frequency: ω d = 15.81 1 − ( 0.142 ) 2 = 15.81 0.9798 = 15.65 rad/s \omega_d = 15.81\sqrt{1-(0.142)^2} = 15.81\sqrt{0.9798} = 15.65\ \text{rad/s} ω d ​ = 15.81 1 − ( 0.142 ) 2 ​ = 15.81 0.9798 ​ = 15.65 rad/s

Only 1% below ω n \omega_n ω n ​ . Resonant amplification if forced at ω n \omega_n ω n ​ : M F = 1 / ( 2 × 0.142 ) = 3.5 × MF = 1/(2 \times 0.142) = 3.5\times MF = 1/ ( 2 × 0.142 ) = 3.5 × — modest, because the damper is doing its job. Remove the damper and the amplification is unbounded.

Trap: adding the two springs' deflections instead of their stiffnesses treats parallel springs as series, giving k e q = 2,500 k_{eq} = 2{,}500 k e q ​ = 2 , 500 N/m and f n = 1.26 f_n = 1.26 f n ​ = 1.26 Hz — exactly half the correct value.