Study guide

13.4 Electrical Measuring Devices: Voltmeter, Ammeter, and Wattmeter

FE Other Disciplines Fundamentals of Engineering

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Strategy

About the FE Other Disciplines Exam How to Use This Study Guide

2 Chapter 1: Mathematics

1.1 Analytic Geometry, Trigonometry, and Vector Operations 1.2 Differential and Integral Calculus 1.3 Ordinary Differential Equations and Laplace Transforms 1.4 Linear Algebra, Matrices, and Systems of Equations 1.5 Numerical Methods, Root-Finding, and Numerical Integration

3 Chapter 2: Probability and Statistics

2.1 Probability Distributions, PMFs, and PDFs 2.2 Expected Value, Mean, Variance, and Descriptive Statistics 2.3 Estimation, Confidence Intervals, and Sample Sizes 2.4 Hypothesis Testing, Goodness of Fit, and Linear Regression

4 Chapter 3: Chemistry

3.1 Stoichiometry, Chemical Reactions, and Solutions 3.2 Chemical Equilibrium, Acids/Bases, and Ideal Gas Laws 3.3 Oxidation-Reduction, Electrochemistry, and Corrosion Basics

5 Chapter 4: Instrumentation and Controls

4.1 Sensors, Transducers, and Signal Conditioning 4.2 Data Sampling, Accuracy/Precision, and A/D Conversion 4.3 Logic Diagrams, Boolean Algebra, and Control Logic

6 Chapter 5: Engineering Ethics and Societal Impacts

5.1 NCEES Model Rules of Professional Conduct and Codes of Ethics 5.2 Public Protection, Licensure Boards, and Professional Liability 5.3 Societal Impacts: Sustainability, Life-Cycle Analysis, and Public Safety

7 Chapter 6: Safety, Health, and Environment

6.1 OSHA Regulations, Industrial Hygiene, and PPE 6.2 Hazard Assessment, Risk Management, and Environmental Rules 6.3 Gas Detection and Monitoring 6.4 Electrical Safety 6.5 Confined Space Entry and Ventilation Rates

8 Chapter 7: Engineering Economics

7.1 Time Value of Money, Interest Formulas, and Cash Flow Diagrams 7.2 Capital Budgeting: Present Worth, Annual Worth, IRR, and B/C Ratio 7.3 Depreciation Methods, Income Taxes, and Breakeven Analysis 7.4 Cost Analysis, Uncertainty, Expected Value, and Decision Trees

9 Chapter 8: Statics

8.1 Statics Equilibrium, Free-Body Diagrams, and Force Systems 8.2 Distributed Loads, Resultants, and Equivalent Force-Couple Systems 8.3 Internal Forces in Rigid Bodies: Trusses, Frames, Machines, and Friction 8.4 Three-Dimensional Equilibrium, Cables, and Pulley Systems 8.5 Area Properties: Centroids, Moments of Inertia, and Radius of Gyration 8.6 Weight, Mass, and Force Units: slug, lbm, lbf, and g_c

10 Chapter 9: Dynamics

9.1 Kinematics of Particles and Rigid Bodies 9.2 Newton's Second Law for Particles and Rigid Bodies 9.3 Angular Motion, Torque, and Mass Moment of Inertia 9.4 Work-Energy Principle, Power, and Efficiency 9.5 Impulse-Momentum, Impact, and Coefficient of Restitution 9.6 Dynamic Friction and Vibrations: Natural Frequency and Damping

11 Chapter 10: Strength of Materials

10.1 Stress Types, Axial Stress-Strain, and Thermal Deformation 10.2 Torsion of Circular Shafts, Polar Moment, and Angle of Twist 10.3 Shear and Moment Diagrams 10.4 Flexural Bending Stress and Transverse Shear Stress 10.5 Stress Transformations, Principal Stresses, and Mohr's Circle 10.6 Beam Deflections and Combined Axial/Bending Loading 10.7 Column Buckling (Euler Formula) and Yield/Failure Criteria

12 Chapter 11: Materials

11.1 Crystal Structure, Phase Diagrams, and Material Processing 11.2 Mechanical Properties, Fatigue, Fracture, and Corrosion 11.3 Thermal Properties of Materials 11.4 Electrical and Chemical Properties of Materials 11.5 Material Selection for Engineering Design

13 Chapter 12: Fluid Mechanics

12.1 Fluid Properties, Hydrostatic Pressure, and Manometry 12.2 Dimensionless Numbers and Flow Regimes 12.3 Continuity Equation, Bernoulli Equation, and Energy Equation 12.4 Impulse-Momentum Equation and Forces on Control Volumes 12.5 Flow in Pipes, Friction Factors (Moody Diagram), and Head Losses 12.6 Turbomachinery: Pumps, Turbines, Fans, and Compressors 12.7 Open-Channel Flow, Manning's Equation, and Drag 12.8 Fluid Transport Systems and Flow Measurement 12.9 Ideal Gas Law, Gas Mixtures, and the Real Gas Law

14 Chapter 13: Basic Electrical Engineering

13.1 Electrical Fundamentals, Ohm's Law, and DC Circuits 13.2 AC Circuits, Phasors, Impedance, and Three-Phase Power 13.3 Magnetic Fields, Induction, Transformers, and Motor Efficiency 13.4 Electrical Measuring Devices: Voltmeter, Ammeter, and Wattmeter

15 Chapter 14: Thermodynamics and Heat Transfer

14.1 First & Second Laws of Thermodynamics and Pure Substance Properties 14.2 Thermodynamic Processes and Property Diagrams (T-s, P-h, P-v) 14.3 Heat Transfer: Conduction, Convection, and Radiation 14.4 Ideal Gas Processes and Power/Refrigeration Cycles 14.5 Mass and Energy Balances on Control Volumes 14.6 Combustion and Combustion Products 14.7 Psychrometrics: Relative Humidity, Wet-Bulb Temperature, and the Psychrometric Chart

13.4 Electrical Measuring Devices: Voltmeter, Ammeter, and Wattmeter

Key Takeaways Explain This Topic AI

NCEES lists measuring devices, naming the voltmeter, ammeter, and wattmeter, as its own Basic Electrical Engineering sub-topic.

A voltmeter connects in parallel and must have very high internal resistance; an ammeter connects in series and must have very low internal resistance.

Connecting an ammeter in parallel across a source creates a near short circuit, which is the most destructive instrument error.

Loading error occurs when the meter's own impedance alters the circuit being measured, and it is worst when the meter resistance is comparable to the circuit resistance.

A wattmeter measures true average power including power factor, so on an AC circuit its reading is less than the product of separate voltmeter and ammeter readings whenever the power factor is below unity.

Last updated: August 2026

13.4 Electrical Measuring Devices: Voltmeter, Ammeter, and Wattmeter

NCEES lists "Measuring devices (e.g., voltmeter, ammeter, wattmeter)" as one of five Basic Electrical Engineering sub-topics. It is examined conceptually — connection topology, ideal internal impedance, and loading error — with occasional short calculations. Small topic, quick points.

The Two Connection Rules

Instrument Measures Connection Ideal internal resistance Why

Voltmeter Potential difference Parallel (across the element) Infinite ( → ∞ \to \infty → ∞ ) Must draw no current, so it cannot divert any from the circuit

Ammeter Current Series (in the current path) Zero ( → 0 \to 0 → 0 ) Must drop no voltage, so it cannot reduce the circuit current

Ohmmeter Resistance Across a de-energized element Supplies its own source External voltage corrupts the reading and can destroy the meter

Wattmeter True average power Current coil in series , voltage coil in parallel Both, as above Needs both quantities simultaneously, with their phase relationship

Memorize the pairing: voltmeter — parallel — high resistance and ammeter — series — low resistance . Everything else in the topic follows from it.

The Consequences of Getting It Wrong

Error Result

Ammeter in parallel across a source Its near-zero resistance forms a short circuit — the most destructive instrument mistake, typically destroying the meter and tripping protection

Voltmeter in series with a load Its enormous resistance nearly opens the circuit ; the load stops working and the voltmeter reads almost the full source voltage

  • Ohmmeter on an energized circuit Wrong reading and probable meter damage
  • Loading Error

A real meter changes the circuit it measures. The magnitude of the disturbance depends on the ratio of meter resistance to circuit resistance.

Voltmeter Loading

A voltmeter of resistance R V R_V R V ​ across a resistor R R R makes the effective resistance: R eff = R R V R + R V R_{\text{eff}} = \frac{R\,R_V}{R + R_V} R eff ​ = R + R V ​ R R V ​ ​

The reading is low, and the fractional error is approximately: error ≈ − R Th R Th + R V \text{error} \approx -\frac{R_{\text{Th}}}{R_{\text{Th}} + R_V} error ≈ − R Th ​ + R V ​ R Th ​ ​

where R Th R_{\text{Th}} R Th ​ is the Thevenin resistance seen by the meter.

Worked Example: Voltmeter Loading in a Divider

Two 1.0 MΩ resistors form a divider across 100 V. A voltmeter with R V = 10 R_V = 10 R V ​ = 10 MΩ measures across the lower resistor. What does it read?

True value (no meter): V = 100 × 1.0 1.0 + 1.0 = 50.0 V = 100 \times \frac{1.0}{1.0+1.0} = 50.0 V = 100 × 1.0 + 1.0 1.0 ​ = 50.0 V.

With the meter , the lower resistor is paralleled by 10 MΩ: R eff = 1.0 ( 10 ) 1.0 + 10 = 0.909 M Ω R_{\text{eff}} = \frac{1.0(10)}{1.0+10} = 0.909\ \text{M}\Omega R eff ​ = 1.0 + 10 1.0 ( 10 ) ​ = 0.909 M Ω V read = 100 × 0.909 1.0 + 0.909 = 100 × 0.909 1.909 = 47.6 V V_{\text{read}} = 100 \times \frac{0.909}{1.0+0.909} = 100 \times \frac{0.909}{1.909} = \boxed{47.6\ \text{V}} V read ​ = 100 × 1.0 + 0.909 0.909 ​ = 100 × 1.909 0.909 ​ = 47.6 V ​

A 4.8% error from a meter whose resistance is 10× the circuit resistance. This is why high-impedance circuits demand high-impedance meters: a modern digital multimeter at 10 MΩ is adequate here, while an old 20 kΩ/V analog meter would read about 2 V and be worthless.

The rule of thumb: keep R V ≥ 100 R Th R_V \ge 100 R_{\text{Th}} R V ​ ≥ 100 R Th ​ for error under 1%. In low-impedance power circuits ( R Th R_{\text{Th}} R Th ​ of a few ohms) loading is negligible; in sensor and instrumentation circuits it dominates.

  • Range Extension: Shunts and Multipliers
  • Ammeter Shunt (parallel)

To extend an ammeter of full-scale current I m I_m I m ​ and resistance R m R_m R m ​ to measure I total I_{\text{total}} I total ​ : R sh = I m R m I total − I m = R m n − 1 , n = I total I m R_{\text{sh}} = \frac{I_mR_m}{I_{\text{total}} - I_m} = \frac{R_m}{n-1}, \qquad n = \frac{I_{\text{total}}}{I_m} R sh ​ = I total ​ − I m ​ I m ​ R m ​ ​ = n − 1 R m ​ ​ , n = I m ​ I total ​ ​

Voltmeter Multiplier (series)

To extend a movement of full-scale voltage V m V_m V m ​ to measure V total V_{\text{total}} V total ​ : R mult = R m ( V total V m − 1 ) = R m ( n − 1 ) R_{\text{mult}} = R_m\left(\frac{V_{\text{total}}}{V_m} - 1\right) = R_m(n-1) R mult ​ = R m ​ ( V m ​ V total ​ ​ − 1 ) = R m ​ ( n − 1 )

Note the symmetry: the shunt divides R m R_m R m ​ by ( n − 1 ) (n-1) ( n − 1 ) and sits in parallel ; the multiplier multiplies R m R_m R m ​ by ( n − 1 ) (n-1) ( n − 1 ) and sits in series . Both follow directly from the connection rules.

For high AC currents and voltages, instrument transformers replace shunts and multipliers: a current transformer (CT) steps current down to a 5 A or 1 A secondary, and a potential transformer (PT) steps voltage down to 120 V. A CT secondary must never be open-circuited while primary current flows — the core saturates and dangerous voltages appear at the terminals.

The Wattmeter

A wattmeter has two coils and reads the true average power , automatically including the phase relationship: P = 1 T ∫ 0 T v ( t ) i ( t ) d t = V rms I rms cos ⁡ θ P = \frac{1}{T}\int_0^T v(t)i(t)\,dt = V_{\text{rms}}I_{\text{rms}}\cos\theta P = T 1 ​ ∫ 0 T ​ v ( t ) i ( t ) d t = V rms ​ I rms ​ cos θ

  • Coil Connection
  • Current coil In series with the load
  • Voltage (potential) coil In parallel with the load

The wattmeter's defining advantage. On an AC circuit, a voltmeter reading times an ammeter reading gives apparent power S = V I S = VI S = V I in volt-amperes — not real power. The wattmeter multiplies the instantaneous values before averaging, so it captures cos ⁡ θ \cos\theta cos θ and reports watts.

Power factor = wattmeter reading voltmeter × ammeter = P S = cos ⁡ θ \text{Power factor} = \frac{\text{wattmeter reading}}{\text{voltmeter} \times \text{ammeter}} = \frac{P}{S} = \cos\theta Power factor = voltmeter × ammeter wattmeter reading ​ = S P ​ = cos θ

This is the standard exam item on this sub-topic , and it also gives you a practical way to determine power factor from three instruments.

Worked Example: Power Factor from Three Meters

A single-phase motor circuit reads 240 V, 18 A, and 3{,}240 W. Find the power factor, apparent power, and reactive power. S = V I = 240 ( 18 ) = 4,320 VA S = VI = 240(18) = 4{,}320\ \text{VA} S = V I = 240 ( 18 ) = 4 , 320 VA p f = cos ⁡ θ = P S = 3,240 4,320 = 0.75 lagging pf = \cos\theta = \frac{P}{S} = \frac{3{,}240}{4{,}320} = \boxed{0.75\ \text{lagging}} p f = cos θ = S P ​ = 4 , 320 3 , 240 ​ = 0.75 lagging ​ θ = arccos ⁡ ( 0.75 ) = 41.4 ° \theta = \arccos(0.75) = 41.4° θ = arccos ( 0.75 ) = 41.4° Q = S sin ⁡ θ = 4,320 sin ⁡ ( 41.4 ° ) = 4,320 ( 0.661 ) = 2,856 VAR Q = S\sin\theta = 4{,}320\sin(41.4°) = 4{,}320(0.661) = 2{,}856\ \text{VAR} Q = S sin θ = 4 , 320 sin ( 41.4° ) = 4 , 320 ( 0.661 ) = 2 , 856 VAR

Check with the power triangle: P 2 + Q 2 = 3,240 2 + 2,856 2 = 1.050 × 10 7 + 8.157 × 10 6 = 1.866 × 10 7 = 4,320 \sqrt{P^2+Q^2} = \sqrt{3{,}240^2 + 2{,}856^2} = \sqrt{1.050\times10^7 + 8.157\times10^6} = \sqrt{1.866\times10^7} = 4{,}320 P 2 + Q 2 ​ = 3 , 24 0 2 + 2 , 85 6 2 ​ = 1.050 × 1 0 7 + 8.157 × 1 0 6 ​ = 1.866 × 1 0 7 ​ = 4 , 320 VA ✓

Trap: assuming P = V I = 4,320 P = VI = 4{,}320 P = V I = 4 , 320 W overstates real power by 33%, and a motor sized on that figure would be a third too large. Only the wattmeter reading is power.

Two-Wattmeter Method for Three-Phase Power

Any three-wire three-phase load — balanced or unbalanced, wye or delta — has its total real power measured by just two wattmeters: P total = W 1 + W 2 P_{\text{total}} = W_1 + W_2 P total ​ = W 1 ​ + W 2 ​

For a balanced load, the two readings also yield the power factor: tan ⁡ θ = 3 W 1 − W 2 W 1 + W 2 \tan\theta = \sqrt{3}\,\frac{W_1 - W_2}{W_1 + W_2} tan θ = 3 ​ W 1 ​ + W 2 ​ W 1 ​ − W 2 ​ ​

  • Power factor Reading behavior
  • p f = 1.0 pf = 1.0 p f = 1.0 W 1 = W 2 W_1 = W_2 W 1 ​ = W 2 ​ (equal readings)
  • p f = 0.5 pf = 0.5 p f = 0.5 One wattmeter reads zero
  • p f < 0.5 pf < 0.5 p f < 0.5 One wattmeter reads negative — reverse its connection and subtract

The negative reading at low power factor surprises candidates but is physically correct, and the total is still W 1 + W 2 W_1 + W_2 W 1 ​ + W 2 ​ with the sign respected.

True-RMS vs. Average-Responding Meters

  • Meter type Reads correctly for Error source
  • True-RMS Any waveform None significant
  • Average-responding, RMS-calibrated Pure sine waves only Reads low on distorted waveforms

Average-responding meters are calibrated by multiplying the rectified average by the sine wave's form factor, 1.11. On the distorted, harmonic-rich currents drawn by variable-frequency drives, switch-mode supplies, and LED lighting, they can read 30–40% low . Where harmonics are present — which is most modern electrical work — a true-RMS instrument is required.