Study guide

5.1 NCEES Model Rules of Professional Conduct and Codes of Ethics

FE Other Disciplines Fundamentals of Engineering

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Strategy

About the FE Other Disciplines Exam How to Use This Study Guide

2 Chapter 1: Mathematics

1.1 Analytic Geometry, Trigonometry, and Vector Operations 1.2 Differential and Integral Calculus 1.3 Ordinary Differential Equations and Laplace Transforms 1.4 Linear Algebra, Matrices, and Systems of Equations 1.5 Numerical Methods, Root-Finding, and Numerical Integration

3 Chapter 2: Probability and Statistics

2.1 Probability Distributions, PMFs, and PDFs 2.2 Expected Value, Mean, Variance, and Descriptive Statistics 2.3 Estimation, Confidence Intervals, and Sample Sizes 2.4 Hypothesis Testing, Goodness of Fit, and Linear Regression

4 Chapter 3: Chemistry

3.1 Stoichiometry, Chemical Reactions, and Solutions 3.2 Chemical Equilibrium, Acids/Bases, and Ideal Gas Laws 3.3 Oxidation-Reduction, Electrochemistry, and Corrosion Basics

5 Chapter 4: Instrumentation and Controls

4.1 Sensors, Transducers, and Signal Conditioning 4.2 Data Sampling, Accuracy/Precision, and A/D Conversion 4.3 Logic Diagrams, Boolean Algebra, and Control Logic

6 Chapter 5: Engineering Ethics and Societal Impacts

5.1 NCEES Model Rules of Professional Conduct and Codes of Ethics 5.2 Public Protection, Licensure Boards, and Professional Liability 5.3 Societal Impacts: Sustainability, Life-Cycle Analysis, and Public Safety

7 Chapter 6: Safety, Health, and Environment

6.1 OSHA Regulations, Industrial Hygiene, and PPE 6.2 Hazard Assessment, Risk Management, and Environmental Rules 6.3 Gas Detection and Monitoring 6.4 Electrical Safety 6.5 Confined Space Entry and Ventilation Rates

8 Chapter 7: Engineering Economics

7.1 Time Value of Money, Interest Formulas, and Cash Flow Diagrams 7.2 Capital Budgeting: Present Worth, Annual Worth, IRR, and B/C Ratio 7.3 Depreciation Methods, Income Taxes, and Breakeven Analysis 7.4 Cost Analysis, Uncertainty, Expected Value, and Decision Trees

9 Chapter 8: Statics

8.1 Statics Equilibrium, Free-Body Diagrams, and Force Systems 8.2 Distributed Loads, Resultants, and Equivalent Force-Couple Systems 8.3 Internal Forces in Rigid Bodies: Trusses, Frames, Machines, and Friction 8.4 Three-Dimensional Equilibrium, Cables, and Pulley Systems 8.5 Area Properties: Centroids, Moments of Inertia, and Radius of Gyration 8.6 Weight, Mass, and Force Units: slug, lbm, lbf, and g_c

10 Chapter 9: Dynamics

9.1 Kinematics of Particles and Rigid Bodies 9.2 Newton's Second Law for Particles and Rigid Bodies 9.3 Angular Motion, Torque, and Mass Moment of Inertia 9.4 Work-Energy Principle, Power, and Efficiency 9.5 Impulse-Momentum, Impact, and Coefficient of Restitution 9.6 Dynamic Friction and Vibrations: Natural Frequency and Damping

11 Chapter 10: Strength of Materials

10.1 Stress Types, Axial Stress-Strain, and Thermal Deformation 10.2 Torsion of Circular Shafts, Polar Moment, and Angle of Twist 10.3 Shear and Moment Diagrams 10.4 Flexural Bending Stress and Transverse Shear Stress 10.5 Stress Transformations, Principal Stresses, and Mohr's Circle 10.6 Beam Deflections and Combined Axial/Bending Loading 10.7 Column Buckling (Euler Formula) and Yield/Failure Criteria

12 Chapter 11: Materials

11.1 Crystal Structure, Phase Diagrams, and Material Processing 11.2 Mechanical Properties, Fatigue, Fracture, and Corrosion 11.3 Thermal Properties of Materials 11.4 Electrical and Chemical Properties of Materials 11.5 Material Selection for Engineering Design

13 Chapter 12: Fluid Mechanics

12.1 Fluid Properties, Hydrostatic Pressure, and Manometry 12.2 Dimensionless Numbers and Flow Regimes 12.3 Continuity Equation, Bernoulli Equation, and Energy Equation 12.4 Impulse-Momentum Equation and Forces on Control Volumes 12.5 Flow in Pipes, Friction Factors (Moody Diagram), and Head Losses 12.6 Turbomachinery: Pumps, Turbines, Fans, and Compressors 12.7 Open-Channel Flow, Manning's Equation, and Drag 12.8 Fluid Transport Systems and Flow Measurement 12.9 Ideal Gas Law, Gas Mixtures, and the Real Gas Law

14 Chapter 13: Basic Electrical Engineering

13.1 Electrical Fundamentals, Ohm's Law, and DC Circuits 13.2 AC Circuits, Phasors, Impedance, and Three-Phase Power 13.3 Magnetic Fields, Induction, Transformers, and Motor Efficiency 13.4 Electrical Measuring Devices: Voltmeter, Ammeter, and Wattmeter

15 Chapter 14: Thermodynamics and Heat Transfer

14.1 First & Second Laws of Thermodynamics and Pure Substance Properties 14.2 Thermodynamic Processes and Property Diagrams (T-s, P-h, P-v) 14.3 Heat Transfer: Conduction, Convection, and Radiation 14.4 Ideal Gas Processes and Power/Refrigeration Cycles 14.5 Mass and Energy Balances on Control Volumes 14.6 Combustion and Combustion Products 14.7 Psychrometrics: Relative Humidity, Wet-Bulb Temperature, and the Psychrometric Chart

5.1 NCEES Model Rules of Professional Conduct and Codes of Ethics

Key Takeaways Explain This Topic AI

The NCEES Model Rules of Professional Conduct mandate that an engineer's primary and paramount obligation is to safeguard the health, safety, and welfare of the public above all commercial, client, or personal interests.

Licensees are legally and ethically restricted to performing engineering assignments only within their specific areas of technical competence based on education, training, and experience.

Engineers must seal and sign only those engineering documents, plans, and calculations prepared under their direct supervisory control or personal technical review.

Engineers must act as faithful agents or trustees for employers and clients, disclosing all real or potential conflicts of interest and refusing multi-party compensation without written consent.

All public statements, reports, expert testimony, and promotional materials must be objective, truthful, and based on adequate knowledge of relevant facts and professional competence.

Last updated: August 2026

5.1 NCEES Model Rules of Professional Conduct and Codes of Ethics

Core Principle: The National Council of Examiners for Engineering and Surveying (NCEES) Model Rules set the standard code of ethics for professional practice across all engineering disciplines. The fundamental canon dictates that engineers shall hold paramount the safety, health, and welfare of the public in the performance of their professional duties.

Structure of the NCEES Model Rules

The NCEES Model Rules of Professional Conduct are partitioned into three major categories of professional obligation:

Obligation to Society: Protecting public health, safety, and welfare, issuing truthful public statements, and reporting safety or ethical violations to proper authorities.

Obligation to Employers and Clients: Acting as faithful agents or trustees, maintaining confidentiality of proprietary technical data, and identifying and disclosing conflicts of interest.

Obligation to Other Licensees & the Profession: Maintaining professional dignity, avoiding unfair competition, honoring professional credentials, and refraining from illegal solicitations or misrepresentations.

Category Primary Ethical Focus Key NCEES Mandate

Obligation to Society Public Health, Safety, & Welfare Paramount duty above all financial, client, or employer interests

Obligation to Employers/Clients Faithful Agency & Loyalty Full written disclosure of conflicts; confidentiality of proprietary data

Obligation to Licensees Professional Integrity No false credentials; no illegal solicitations, bribes, or plan stamping

The Paramount Rule: Public Health, Safety, and Welfare

In engineering practice, technical design decisions frequently intersect with economic constraints, client budget limits, and aggressive project schedules. However, NCEES Model Rules establish an absolute ethical hierarchy: public safety takes precedence over all other considerations .

Conflict Resolution & Whistleblowing Protocols

When an engineer's professional judgment is overruled by a client, project supervisor, or corporate executive under circumstances where life, health, safety, property, or public welfare are endangered, the engineer must adhere to a strict multi-step ethical protocol:

Internal Technical Notification: Formally notify the employer, client, or project manager in writing, clearly identifying the technical deficiency, potential failure mode, and safety risk.

Refusal to Sanction: Refuse to sign, seal, or approve engineering plans, calculations, or specifications that fail to comply with applicable safety standards and building codes.

External Regulatory Disclosure (Whistleblowing): If management or the client fails to take corrective action, the engineer is obligated to inform the appropriate public regulatory authority (such as the local building official, environmental authority, or state engineering licensing board).

Loading diagram... NCEES Whistleblowing & Safety Escalation Protocol

  • Scope of Competence and Sealing/Stamping Requirements
  • Performing Work Within Areas of Competence

NCEES Model Rules require engineers to perform engineering assignments only in the specific fields in which they are qualified by education, training, or experience:

A licensed engineer educated in civil/structural engineering cannot sign or seal electrical distribution or chemical process plans unless they possess documented technical competence in those specific engineering disciplines.

On multi-disciplinary projects, a lead engineer may sign and seal the overall project submission only if each technical segment is signed and sealed by the qualified licensed engineer who prepared or directly supervised that specific portion.

Direct Supervisory Control

One of the most heavily tested NCEES ethical concepts on the FE examination is the requirement of direct supervisory control (also referred to as direct engineering control and responsible charge) for sealing engineering documents. Direct Supervisory Control ⟹ { Personal direction and technical oversight of design staff Direct involvement in calculations and engineering decisions Authority to modify, revise, or reject work prior to sealing \text{Direct Supervisory Control} \implies \begin{cases} \text{Personal direction and technical oversight of design staff} \\\ \text{Direct involvement in calculations and engineering decisions} \\\ \text{Authority to modify, revise, or reject work prior to sealing} \end{cases} Direct Supervisory Control ⟹ ⎩ ⎨ ⎧ ​ Personal direction and technical oversight of design staff Direct involvement in calculations and engineering decisions Authority to modify, revise, or reject work prior to sealing ​

Sealing Rules and Prohibited Practices

Practice Status Legal & Ethical Implication

Sealing Own Work Permitted Engineer authored calculations, drawings, or specifications directly.

Sealing Supervised Work Permitted Work prepared by subordinates under the engineer's direct supervisory control.

Plan Stamping Prohibited Sealing work prepared by an un-affiliated third party without direct oversight.

Post-Facto Sealing Prohibited Sealing completed plans prepared by others after a superficial visual review.

Definition — Plan Stamping: The illegal practice of affixing a professional seal or signature to engineering plans, reports, or calculations that were not prepared under the licensee's direct supervisory control. Plan stamping is a severe violation that results in license revocation, administrative fines, and potential legal liability.

  • Obligations to Employers and Clients
  • Acting as Faithful Agents or Trustees

Engineers must act in professional matters for each employer or client as faithful agents or trustees. This requires maintaining strict confidentiality of business affairs, proprietary technical data, and trade secrets obtained during employment or consulting engagements.

Managing Conflicts of Interest

A conflict of interest arises when an engineer has personal, financial, or professional interests that could compromise—or appear to compromise—their independent professional judgment.

NCEES Conflict of Interest Rules:

Full Written Disclosure: Licensees must promptly inform their employers or clients of any business association, interest, or circumstances that could influence their judgment or the quality of their services.

Multi-Party Compensation: Licensees shall not accept financial or other valuable consideration from more than one party for services on the same project (or for services pertaining to the same project) unless the circumstances are fully disclosed to, and agreed to in writing by, all interested parties.

Supplier Gratuities & Kickbacks: Engineers shall not solicit or accept financial or other valuable considerations (such as kickbacks, lavish gifts, free equipment, or contingent fees) from material suppliers, equipment vendors, or construction contractors in exchange for specifying their products.

  • Public Statements, Truthfulness, and Professional Misconduct
  • Objectivity in Public Reports and Expert Testimony

When engineers issue public statements, engineering reports, expert testimony, or published articles, NCEES rules enforce strict standards of truthfulness and objectivity:

Reports and testimony must be truthful, objective, and unbiased .

Engineers must express engineering opinions only when founded upon adequate knowledge of the facts and competent evaluation of the subject matter.

When testifying as an expert witness, an engineer must express an honest engineering opinion based on technical facts, rather than serving as an advocate for the hiring party.

Public statements must disclose whether the engineer is being compensated by an interested party.

Solicitation, Bribery, and Misrepresentation

Engineers must maintain the highest standards of integrity when seeking employment or business engagements:

No False Credentials: Misrepresenting academic degrees, licensure status, professional experience, or firm capacity is illegal and unethical.

Prohibition on Bribery: Engineers shall not offer, give, solicit, or receive any gift, bribe, or political contribution with the intent to influence the award of a public or private contract.

Contingent Fee Arrangements: Engineers shall not accept contracts under contingent fee arrangements where their professional judgment might be compromised by financial stakes tied to a specific engineering finding or approval outcome.

Worked Ethical Case Study Problem

Scenario: An engineer is hired by a land developer to perform an environmental site assessment for a proposed housing project. During soil sampling, the engineer discovers toxic heavy metal contamination exceeding state health limits. The developer demands that the engineer omit the contamination data from the final public report, threatening to withhold payment and fire the engineer if the report is modified.

Ethical Analysis & Step-by-Step Resolution:

Evaluate the Conflict: The client's demand pits commercial interest (getting paid) against public safety (heavy metal contamination poses a direct health hazard to future residents).

Apply the Paramount Rule: NCEES rules state public health and safety must be held paramount over client desires or financial compensation.

Identify Mandatory Actions:

The engineer must refuse to alter or omit the contamination data from the report.

The engineer must issue an accurate, objective report containing the true soil findings.

If the developer refuses to notify public health officials and attempts to conceal the hazard, the engineer has an affirmative obligation to inform the state environmental regulatory agency and local building authority.