Study guide
12.7 Open-Channel Flow, Manning's Equation, and Drag
FE Other Disciplines Fundamentals of Engineering
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Exam Strategy
About the FE Other Disciplines Exam How to Use This Study Guide
2 Chapter 1: Mathematics
1.1 Analytic Geometry, Trigonometry, and Vector Operations 1.2 Differential and Integral Calculus 1.3 Ordinary Differential Equations and Laplace Transforms 1.4 Linear Algebra, Matrices, and Systems of Equations 1.5 Numerical Methods, Root-Finding, and Numerical Integration
3 Chapter 2: Probability and Statistics
2.1 Probability Distributions, PMFs, and PDFs 2.2 Expected Value, Mean, Variance, and Descriptive Statistics 2.3 Estimation, Confidence Intervals, and Sample Sizes 2.4 Hypothesis Testing, Goodness of Fit, and Linear Regression
4 Chapter 3: Chemistry
3.1 Stoichiometry, Chemical Reactions, and Solutions 3.2 Chemical Equilibrium, Acids/Bases, and Ideal Gas Laws 3.3 Oxidation-Reduction, Electrochemistry, and Corrosion Basics
5 Chapter 4: Instrumentation and Controls
4.1 Sensors, Transducers, and Signal Conditioning 4.2 Data Sampling, Accuracy/Precision, and A/D Conversion 4.3 Logic Diagrams, Boolean Algebra, and Control Logic
6 Chapter 5: Engineering Ethics and Societal Impacts
5.1 NCEES Model Rules of Professional Conduct and Codes of Ethics 5.2 Public Protection, Licensure Boards, and Professional Liability 5.3 Societal Impacts: Sustainability, Life-Cycle Analysis, and Public Safety
7 Chapter 6: Safety, Health, and Environment
6.1 OSHA Regulations, Industrial Hygiene, and PPE 6.2 Hazard Assessment, Risk Management, and Environmental Rules 6.3 Gas Detection and Monitoring 6.4 Electrical Safety 6.5 Confined Space Entry and Ventilation Rates
8 Chapter 7: Engineering Economics
7.1 Time Value of Money, Interest Formulas, and Cash Flow Diagrams 7.2 Capital Budgeting: Present Worth, Annual Worth, IRR, and B/C Ratio 7.3 Depreciation Methods, Income Taxes, and Breakeven Analysis 7.4 Cost Analysis, Uncertainty, Expected Value, and Decision Trees
9 Chapter 8: Statics
8.1 Statics Equilibrium, Free-Body Diagrams, and Force Systems 8.2 Distributed Loads, Resultants, and Equivalent Force-Couple Systems 8.3 Internal Forces in Rigid Bodies: Trusses, Frames, Machines, and Friction 8.4 Three-Dimensional Equilibrium, Cables, and Pulley Systems 8.5 Area Properties: Centroids, Moments of Inertia, and Radius of Gyration 8.6 Weight, Mass, and Force Units: slug, lbm, lbf, and g_c
10 Chapter 9: Dynamics
9.1 Kinematics of Particles and Rigid Bodies 9.2 Newton's Second Law for Particles and Rigid Bodies 9.3 Angular Motion, Torque, and Mass Moment of Inertia 9.4 Work-Energy Principle, Power, and Efficiency 9.5 Impulse-Momentum, Impact, and Coefficient of Restitution 9.6 Dynamic Friction and Vibrations: Natural Frequency and Damping
11 Chapter 10: Strength of Materials
10.1 Stress Types, Axial Stress-Strain, and Thermal Deformation 10.2 Torsion of Circular Shafts, Polar Moment, and Angle of Twist 10.3 Shear and Moment Diagrams 10.4 Flexural Bending Stress and Transverse Shear Stress 10.5 Stress Transformations, Principal Stresses, and Mohr's Circle 10.6 Beam Deflections and Combined Axial/Bending Loading 10.7 Column Buckling (Euler Formula) and Yield/Failure Criteria
12 Chapter 11: Materials
11.1 Crystal Structure, Phase Diagrams, and Material Processing 11.2 Mechanical Properties, Fatigue, Fracture, and Corrosion 11.3 Thermal Properties of Materials 11.4 Electrical and Chemical Properties of Materials 11.5 Material Selection for Engineering Design
13 Chapter 12: Fluid Mechanics
12.1 Fluid Properties, Hydrostatic Pressure, and Manometry 12.2 Dimensionless Numbers and Flow Regimes 12.3 Continuity Equation, Bernoulli Equation, and Energy Equation 12.4 Impulse-Momentum Equation and Forces on Control Volumes 12.5 Flow in Pipes, Friction Factors (Moody Diagram), and Head Losses 12.6 Turbomachinery: Pumps, Turbines, Fans, and Compressors 12.7 Open-Channel Flow, Manning's Equation, and Drag 12.8 Fluid Transport Systems and Flow Measurement 12.9 Ideal Gas Law, Gas Mixtures, and the Real Gas Law
14 Chapter 13: Basic Electrical Engineering
13.1 Electrical Fundamentals, Ohm's Law, and DC Circuits 13.2 AC Circuits, Phasors, Impedance, and Three-Phase Power 13.3 Magnetic Fields, Induction, Transformers, and Motor Efficiency 13.4 Electrical Measuring Devices: Voltmeter, Ammeter, and Wattmeter
15 Chapter 14: Thermodynamics and Heat Transfer
14.1 First & Second Laws of Thermodynamics and Pure Substance Properties 14.2 Thermodynamic Processes and Property Diagrams (T-s, P-h, P-v) 14.3 Heat Transfer: Conduction, Convection, and Radiation 14.4 Ideal Gas Processes and Power/Refrigeration Cycles 14.5 Mass and Energy Balances on Control Volumes 14.6 Combustion and Combustion Products 14.7 Psychrometrics: Relative Humidity, Wet-Bulb Temperature, and the Psychrometric Chart
12.7 Open-Channel Flow, Manning's Equation, and Drag
Key Takeaways Explain This Topic AI
NCEES lists open-channel flow with Manning's equation and drag as a single Fluid Mechanics sub-topic.
Manning's equation gives velocity as (1/n) times hydraulic radius to the two-thirds power times the square root of slope in SI units, with a 1.486 coefficient in US Customary units.
Hydraulic radius is flow area divided by wetted perimeter, and for a wide shallow channel it approaches the flow depth.
Discharge is maximized for a given area by the most efficient cross-section, which for a rectangular channel is a width equal to twice the depth.
Drag force is the drag coefficient times one-half rho V squared times the reference area, so drag rises with the square of velocity.
Last updated: August 2026
12.7 Open-Channel Flow, Manning's Equation, and Drag
The NCEES Fluid Mechanics specification pairs these as one sub-topic: "Open-channel flow (e.g., Manning's equation, drag)." Open-channel flow differs fundamentally from pipe flow in that it has a free surface at atmospheric pressure , so the flow is driven by gravity acting on the channel slope rather than by a pressure difference.
Manning's Equation V = 1 n R h 2 / 3 S 1 / 2 (SI: m/s) , Q = 1 n A R h 2 / 3 S 1 / 2 V = \frac{1}{n}R_h^{2/3}S^{1/2} \quad\text{(SI: m/s)}, \qquad Q = \frac{1}{n}A R_h^{2/3}S^{1/2} V = n 1 R h 2/3 S 1/2 (SI: m/s) , Q = n 1 A R h 2/3 S 1/2 V = 1.486 n R h 2 / 3 S 1 / 2 (US Customary: ft/s) V = \frac{1.486}{n}R_h^{2/3}S^{1/2} \quad\text{(US Customary: ft/s)} V = n 1.486 R h 2/3 S 1/2 (US Customary: ft/s)
where n n n is Manning's roughness coefficient (dimensional, and the same numerical value in both systems ), R h R_h R h is the hydraulic radius, and S S S is the channel slope (dimensionless, often the bed slope).
The 1.486 factor is purely a unit conversion , equal to 3.2808 1 / 3 3.2808^{1/3} 3.280 8 1/3 . Applying the SI form to feet under-predicts velocity by 33%, and forgetting it in US Customary work is one of the most common errors in this topic.
Hydraulic Radius R h = A P R_h = \frac{A}{P} R h = P A
with P P P the wetted perimeter — the length of channel boundary in contact with water, excluding the free surface . The free surface has no shear, so it contributes no resistance and is never counted.
Section A A A P P P R h R_h R h
Rectangle, width b b b , depth y y y b y by b y b + 2 y b + 2y b + 2 y b y b + 2 y \dfrac{by}{b+2y} b + 2 y b y
Wide shallow channel ( b ≫ y b \gg y b ≫ y ) b y by b y ≈ b \approx b ≈ b ≈ y \approx y ≈ y
Trapezoid, side slope z z z :1 b y + z y 2 by + zy^2 b y + z y 2 b + 2 y 1 + z 2 b + 2y\sqrt{1+z^2} b + 2 y 1 + z 2 b y + z y 2 b + 2 y 1 + z 2 \dfrac{by+zy^2}{b+2y\sqrt{1+z^2}} b + 2 y 1 + z 2 b y + z y 2
- Circular pipe flowing full π D 2 / 4 \pi D^2/4 π D 2 /4 π D \pi D π D D / 4 D/4 D /4
- Circular pipe flowing half full π D 2 / 8 \pi D^2/8 π D 2 /8 π D / 2 \pi D/2 π D /2 D / 4 D/4 D /4
A pipe flowing half full has the same hydraulic radius as one flowing full — both are D / 4 D/4 D /4 — so Manning's equation gives them the same velocity . Since the half-full pipe has half the area, it carries half the discharge at the same velocity. And a partly full pipe actually carries its maximum discharge at about 94% of full depth , because the wetted perimeter grows faster than the area in the last few percent. This counterintuitive result is a favorite exam item.
Manning's Roughness Coefficients
- Channel surface n n n
- Glass, smooth plastic 0.010
- Finished concrete 0.012
- Unfinished concrete 0.014
- Corrugated metal pipe 0.022
- Clean earth channel 0.022
- Gravel bed 0.025
- Natural stream, clean and straight 0.030
- Natural stream with weeds and stones 0.035–0.050
- Heavy brush, floodplain 0.075–0.150
Because Q ∝ 1 / n Q \propto 1/n Q ∝ 1/ n , a channel that silts up and vegetates from n = 0.014 n = 0.014 n = 0.014 to n = 0.040 n = 0.040 n = 0.040 loses 65% of its capacity at the same depth and slope — the usual explanation for a culvert that suddenly floods after years of service.
Worked Example: Trapezoidal Channel Discharge
A trapezoidal channel has a 3.0 m bottom width, 2:1 side slopes ( z = 2 z = 2 z = 2 ), a flow depth of 1.2 m, n = 0.025 n = 0.025 n = 0.025 , and a bed slope of 0.0008. Find the discharge. A = b y + z y 2 = 3.0 ( 1.2 ) + 2 ( 1.2 ) 2 = 3.60 + 2.88 = 6.48 m 2 A = by + zy^2 = 3.0(1.2) + 2(1.2)^2 = 3.60 + 2.88 = 6.48\ \text{m}^2 A = b y + z y 2 = 3.0 ( 1.2 ) + 2 ( 1.2 ) 2 = 3.60 + 2.88 = 6.48 m 2 P = b + 2 y 1 + z 2 = 3.0 + 2 ( 1.2 ) 1 + 4 = 3.0 + 2.4 ( 2.236 ) = 3.0 + 5.367 = 8.367 m P = b + 2y\sqrt{1+z^2} = 3.0 + 2(1.2)\sqrt{1+4} = 3.0 + 2.4(2.236) = 3.0 + 5.367 = 8.367\ \text{m} P = b + 2 y 1 + z 2 = 3.0 + 2 ( 1.2 ) 1 + 4 = 3.0 + 2.4 ( 2.236 ) = 3.0 + 5.367 = 8.367 m R h = 6.48 8.367 = 0.7746 m R_h = \frac{6.48}{8.367} = 0.7746\ \text{m} R h = 8.367 6.48 = 0.7746 m R h 2 / 3 = ( 0.7746 ) 2 / 3 = e 0.6667 ln 0.7746 = e 0.6667 ( − 0.2553 ) = e − 0.1702 = 0.8435 R_h^{2/3} = (0.7746)^{2/3} = e^{0.6667\ln 0.7746} = e^{0.6667(-0.2553)} = e^{-0.1702} = 0.8435 R h 2/3 = ( 0.7746 ) 2/3 = e 0.6667 l n 0.7746 = e 0.6667 ( − 0.2553 ) = e − 0.1702 = 0.8435 S 1 / 2 = 0.0008 = 0.02828 S^{1/2} = \sqrt{0.0008} = 0.02828 S 1/2 = 0.0008 = 0.02828 Q = 1 0.025 ( 6.48 ) ( 0.8435 ) ( 0.02828 ) = 40 ( 6.48 ) ( 0.8435 ) ( 0.02828 ) = 6.18 m 3 / s Q = \frac{1}{0.025}(6.48)(0.8435)(0.02828) = 40(6.48)(0.8435)(0.02828) = \boxed{6.18\ \text{m}^3/\text{s}} Q = 0.025 1 ( 6.48 ) ( 0.8435 ) ( 0.02828 ) = 40 ( 6.48 ) ( 0.8435 ) ( 0.02828 ) = 6.18 m 3 / s
Mean velocity V = Q / A = 6.18 / 6.48 = 0.954 V = Q/A = 6.18/6.48 = 0.954 V = Q / A = 6.18/6.48 = 0.954 m/s. Froude check: F r = 0.954 / 9.81 ( 1.2 ) = 0.954 / 3.431 = 0.278 Fr = 0.954/\sqrt{9.81(1.2)} = 0.954/3.431 = 0.278 F r = 0.954/ 9.81 ( 1.2 ) = 0.954/3.431 = 0.278 — subcritical , as designed channels normally are.
Most Efficient Cross-Sections
For a fixed cross-sectional area, discharge is maximized when the wetted perimeter is minimized (maximizing R h R_h R h ). This also minimizes lining cost.
- Section Most efficient proportions
- Rectangular b = 2 y b = 2y b = 2 y — width twice the depth, so R h = y / 2 R_h = y/2 R h = y /2
- Trapezoidal Half of a regular hexagon; side slopes at 60°
- Circular Flowing half full (semicircle)
- Overall best Semicircle — least perimeter for a given area
- Normal vs. Critical Depth
- Depth Determined by Meaning
- Normal depth y n y_n y n Manning's equation (roughness, slope, discharge) Uniform-flow equilibrium depth
Critical depth y c y_c y c y c = ( q 2 / g ) 1 / 3 y_c = (q^2/g)^{1/3} y c = ( q 2 / g ) 1/3 Minimum specific energy for that discharge
Comparing them classifies the channel slope: y n > y c y_n > y_c y n > y c is a mild slope with subcritical uniform flow; y n < y c y_n < y_c y n < y c is a steep slope with supercritical uniform flow. E = y + V 2 2 g (specific energy, measured from the channel bed) E = y + \frac{V^2}{2g} \qquad\text{(specific energy, measured from the channel bed)} E = y + 2 g V 2 (specific energy, measured from the channel bed)
Drag F D = C D 1 2 ρ V 2 A F_D = C_D\,\frac{1}{2}\rho V^2 A F D = C D 2 1 ρ V 2 A
where A A A is the reference area — usually the frontal (projected) area for bluff bodies, and the planform area for airfoils. Check which the problem intends, since it changes C D C_D C D by a large factor.
- Body C D C_D C D (frontal area, high R e Re R e )
- Flat plate normal to flow 1.28
- Sphere (subcritical R e Re R e ) 0.47
- Sphere (post-critical, R e > 3 × 10 5 Re > 3\times10^5 R e > 3 × 1 0 5 ) ~0.20
- Circular cylinder (long, crossflow) 1.2
- Streamlined body / airfoil 0.04
- Modern passenger car 0.25–0.35
- Cube, face-on 1.05
- Hemisphere, open side facing flow 1.42
Drag scales with V 2 V^2 V 2 , so power to overcome it scales with V 3 V^3 V 3 ( P = F D V P = F_D V P = F D V ). Doubling a vehicle's speed quadruples the drag force and requires eight times the power. This cubic relationship is why highway fuel economy degrades so sharply with speed.
Terminal Velocity
At terminal velocity, weight minus buoyancy equals drag: V t = 2 ( ρ s − ρ ) V o l g C D ρ A V_t = \sqrt{\frac{2(\rho_s-\rho)Vol\,g}{C_D\rho A}} V t = C D ρ A 2 ( ρ s − ρ ) V o l g
For a sphere of diameter D D D , substituting V o l = π D 3 / 6 Vol = \pi D^3/6 V o l = π D 3 /6 and A = π D 2 / 4 A = \pi D^2/4 A = π D 2 /4 : V t = 4 g D ( ρ s − ρ ) 3 C D ρ V_t = \sqrt{\frac{4gD(\rho_s-\rho)}{3C_D\rho}} V t = 3 C D ρ 4 g D ( ρ s − ρ )
Worked Example: Drag Force and Power
A vehicle with frontal area 2.4 m² and C D = 0.31 C_D = 0.31 C D = 0.31 travels at 100 km/h through air ( ρ = 1.20 \rho = 1.20 ρ = 1.20 kg/m³). Find the drag force and the power required, then compare with 130 km/h. V = 100 3.6 = 27.78 m/s V = \frac{100}{3.6} = 27.78\ \text{m/s} V = 3.6 100 = 27.78 m/s F D = 0.31 ( 1 2 ) ( 1.20 ) ( 27.78 ) 2 ( 2.4 ) = 0.31 ( 0.60 ) ( 771.6 ) ( 2.4 ) = 344.4 N F_D = 0.31\left(\tfrac{1}{2}\right)(1.20)(27.78)^2(2.4) = 0.31(0.60)(771.6)(2.4) = 344.4\ \text{N} F D = 0.31 ( 2 1 ) ( 1.20 ) ( 27.78 ) 2 ( 2.4 ) = 0.31 ( 0.60 ) ( 771.6 ) ( 2.4 ) = 344.4 N P = F D V = 344.4 ( 27.78 ) = 9,568 W = 9.57 kW P = F_D V = 344.4(27.78) = 9{,}568\ \text{W} = \boxed{9.57\ \text{kW}} P = F D V = 344.4 ( 27.78 ) = 9 , 568 W = 9.57 kW
At 130 km/h ( V = 36.11 V = 36.11 V = 36.11 m/s), the ratio is ( 36.11 / 27.78 ) = 1.30 (36.11/27.78) = 1.30 ( 36.11/27.78 ) = 1.30 : F D = 344.4 ( 1.30 ) 2 = 582 N , P = 9.57 ( 1.30 ) 3 = 21.0 kW F_D = 344.4(1.30)^2 = 582\ \text{N}, \qquad P = 9.57(1.30)^3 = \boxed{21.0\ \text{kW}} F D = 344.4 ( 1.30 ) 2 = 582 N , P = 9.57 ( 1.30 ) 3 = 21.0 kW
A 30% speed increase raises drag 69% and required power 120% — more than doubling it. That is the V 3 V^3 V 3 law made concrete.