Study guide
11.5 Material Selection for Engineering Design
FE Other Disciplines Fundamentals of Engineering
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Exam Strategy
About the FE Other Disciplines Exam How to Use This Study Guide
2 Chapter 1: Mathematics
1.1 Analytic Geometry, Trigonometry, and Vector Operations 1.2 Differential and Integral Calculus 1.3 Ordinary Differential Equations and Laplace Transforms 1.4 Linear Algebra, Matrices, and Systems of Equations 1.5 Numerical Methods, Root-Finding, and Numerical Integration
3 Chapter 2: Probability and Statistics
2.1 Probability Distributions, PMFs, and PDFs 2.2 Expected Value, Mean, Variance, and Descriptive Statistics 2.3 Estimation, Confidence Intervals, and Sample Sizes 2.4 Hypothesis Testing, Goodness of Fit, and Linear Regression
4 Chapter 3: Chemistry
3.1 Stoichiometry, Chemical Reactions, and Solutions 3.2 Chemical Equilibrium, Acids/Bases, and Ideal Gas Laws 3.3 Oxidation-Reduction, Electrochemistry, and Corrosion Basics
5 Chapter 4: Instrumentation and Controls
4.1 Sensors, Transducers, and Signal Conditioning 4.2 Data Sampling, Accuracy/Precision, and A/D Conversion 4.3 Logic Diagrams, Boolean Algebra, and Control Logic
6 Chapter 5: Engineering Ethics and Societal Impacts
5.1 NCEES Model Rules of Professional Conduct and Codes of Ethics 5.2 Public Protection, Licensure Boards, and Professional Liability 5.3 Societal Impacts: Sustainability, Life-Cycle Analysis, and Public Safety
7 Chapter 6: Safety, Health, and Environment
6.1 OSHA Regulations, Industrial Hygiene, and PPE 6.2 Hazard Assessment, Risk Management, and Environmental Rules 6.3 Gas Detection and Monitoring 6.4 Electrical Safety 6.5 Confined Space Entry and Ventilation Rates
8 Chapter 7: Engineering Economics
7.1 Time Value of Money, Interest Formulas, and Cash Flow Diagrams 7.2 Capital Budgeting: Present Worth, Annual Worth, IRR, and B/C Ratio 7.3 Depreciation Methods, Income Taxes, and Breakeven Analysis 7.4 Cost Analysis, Uncertainty, Expected Value, and Decision Trees
9 Chapter 8: Statics
8.1 Statics Equilibrium, Free-Body Diagrams, and Force Systems 8.2 Distributed Loads, Resultants, and Equivalent Force-Couple Systems 8.3 Internal Forces in Rigid Bodies: Trusses, Frames, Machines, and Friction 8.4 Three-Dimensional Equilibrium, Cables, and Pulley Systems 8.5 Area Properties: Centroids, Moments of Inertia, and Radius of Gyration 8.6 Weight, Mass, and Force Units: slug, lbm, lbf, and g_c
10 Chapter 9: Dynamics
9.1 Kinematics of Particles and Rigid Bodies 9.2 Newton's Second Law for Particles and Rigid Bodies 9.3 Angular Motion, Torque, and Mass Moment of Inertia 9.4 Work-Energy Principle, Power, and Efficiency 9.5 Impulse-Momentum, Impact, and Coefficient of Restitution 9.6 Dynamic Friction and Vibrations: Natural Frequency and Damping
11 Chapter 10: Strength of Materials
10.1 Stress Types, Axial Stress-Strain, and Thermal Deformation 10.2 Torsion of Circular Shafts, Polar Moment, and Angle of Twist 10.3 Shear and Moment Diagrams 10.4 Flexural Bending Stress and Transverse Shear Stress 10.5 Stress Transformations, Principal Stresses, and Mohr's Circle 10.6 Beam Deflections and Combined Axial/Bending Loading 10.7 Column Buckling (Euler Formula) and Yield/Failure Criteria
12 Chapter 11: Materials
11.1 Crystal Structure, Phase Diagrams, and Material Processing 11.2 Mechanical Properties, Fatigue, Fracture, and Corrosion 11.3 Thermal Properties of Materials 11.4 Electrical and Chemical Properties of Materials 11.5 Material Selection for Engineering Design
13 Chapter 12: Fluid Mechanics
12.1 Fluid Properties, Hydrostatic Pressure, and Manometry 12.2 Dimensionless Numbers and Flow Regimes 12.3 Continuity Equation, Bernoulli Equation, and Energy Equation 12.4 Impulse-Momentum Equation and Forces on Control Volumes 12.5 Flow in Pipes, Friction Factors (Moody Diagram), and Head Losses 12.6 Turbomachinery: Pumps, Turbines, Fans, and Compressors 12.7 Open-Channel Flow, Manning's Equation, and Drag 12.8 Fluid Transport Systems and Flow Measurement 12.9 Ideal Gas Law, Gas Mixtures, and the Real Gas Law
14 Chapter 13: Basic Electrical Engineering
13.1 Electrical Fundamentals, Ohm's Law, and DC Circuits 13.2 AC Circuits, Phasors, Impedance, and Three-Phase Power 13.3 Magnetic Fields, Induction, Transformers, and Motor Efficiency 13.4 Electrical Measuring Devices: Voltmeter, Ammeter, and Wattmeter
15 Chapter 14: Thermodynamics and Heat Transfer
14.1 First & Second Laws of Thermodynamics and Pure Substance Properties 14.2 Thermodynamic Processes and Property Diagrams (T-s, P-h, P-v) 14.3 Heat Transfer: Conduction, Convection, and Radiation 14.4 Ideal Gas Processes and Power/Refrigeration Cycles 14.5 Mass and Energy Balances on Control Volumes 14.6 Combustion and Combustion Products 14.7 Psychrometrics: Relative Humidity, Wet-Bulb Temperature, and the Psychrometric Chart
11.5 Material Selection for Engineering Design
Key Takeaways Explain This Topic AI
NCEES lists material selection as its own Materials sub-topic, so it is examined as a decision process rather than a property lookup.
Specific strength is strength divided by density and specific stiffness is modulus divided by density; these govern weight-critical design.
For a beam of fixed geometry minimizing mass at a given stiffness, the material index to maximize is E^(1/2)/rho, which is why wood and composites outperform steel per unit weight.
Aluminum and steel have almost identical specific stiffness, so substituting aluminum for steel saves weight only by using a deeper or thicker section.
A single limiting requirement such as maximum service temperature or chloride exposure eliminates whole material classes before any optimization begins.
Last updated: August 2026
11.5 Material Selection for Engineering Design
NCEES lists "Material selection" as a Materials sub-topic in its own right. It is not a property-recall item — it asks you to compare candidates against a stated requirement, which means normalizing properties and knowing which normalization the requirement implies.
The Selection Process
- Step Question Output
- 1. Translate What must the part do, and what must it not do? Function, constraints, objective, free variables
- 2. Screen Which materials fail a hard constraint outright? Reduced candidate list
- 3. Rank Which surviving candidate best serves the objective? Material index
4. Document What supporting information decides between close finishers? Cost, availability, joinability, code approval
Screening comes before ranking, and it is where most real selections are decided. A single hard constraint — maximum service temperature, chloride exposure, food contact, code listing, electrical isolation — eliminates entire classes before any optimization begins. An exam item that specifies a service condition is usually testing screening, not optimization.
Normalizing Properties: Specific Strength and Stiffness
Absolute properties mislead whenever weight matters: Specific strength = σ y ρ , Specific stiffness = E ρ \text{Specific strength} = \frac{\sigma_y}{\rho}, \qquad \text{Specific stiffness} = \frac{E}{\rho} Specific strength = ρ σ y , Specific stiffness = ρ E
Material ρ \rho ρ (kg/m³) E E E (GPa) σ y \sigma_y σ y (MPa) E / ρ E/\rho E / ρ (MPa·m³/kg) σ y / ρ \sigma_y/\rho σ y / ρ (kPa·m³/kg)
- Structural steel (A36) 7{,}850 200 250 25.5 31.8
- High-strength steel 7{,}850 200 1{,}000 25.5 127
- Aluminum 6061-T6 2{,}700 69 276 25.6 102
- Titanium Ti-6Al-4V 4{,}430 114 880 25.7 199
- Magnesium AZ91 1{,}810 45 160 24.9 88
- Carbon fiber composite 1{,}600 150 1{,}500 93.8 938
- Douglas fir (along grain) 500 13 50 26.0 100
- Alumina ceramic 3{,}900 370 300 (compressive ~2{,}500) 94.9 77
- Nylon 6/6 1{,}140 3 80 2.6 70
The striking result in that table: steel, aluminum, titanium, magnesium, and wood all have specific stiffness E / ρ E/\rho E / ρ near 25–26 . This is not coincidence — for metals it reflects the similar stiffness of atomic bonds per unit mass. Substituting aluminum for steel does not save weight in a stiffness-limited part unless the section geometry also changes , because the two have essentially identical E / ρ E/\rho E / ρ . Aluminum wins in practice by allowing a thicker or deeper section at equal weight, which raises I I I — and I I I scales with h 3 h^3 h 3 .
Only carbon fiber composites and ceramics break out of the pack, at roughly 3.7× the specific stiffness of metals.
Material Indices
When the geometry is free to change, the property combination to maximize depends on the loading mode:
- Design objective Free variable Index to maximize
- Minimum mass tie rod at given stiffness Area E / ρ E/\rho E / ρ
- Minimum mass beam at given stiffness Section depth E 1 / 2 / ρ E^{1/2}/\rho E 1/2 / ρ
- Minimum mass plate/panel at given stiffness Thickness E 1 / 3 / ρ E^{1/3}/\rho E 1/3 / ρ
- Minimum mass beam at given strength Section depth σ f 2 / 3 / ρ \sigma_f^{2/3}/\rho σ f 2/3 / ρ
- Maximum elastic energy storage (springs) — σ f 2 / E \sigma_f^2/E σ f 2 / E
- Best thermal shock resistance — σ f k / ( E α ) \sigma_f k/(E\alpha) σ f k / ( E α )
The fractional exponents come from the fact that a beam's stiffness depends on I ∝ h 4 I \propto h^4 I ∝ h 4 while its mass depends on h 2 h^2 h 2 , so allowing depth to change rewards low density more heavily than high modulus.
Worked Example: Beam Material for Minimum Weight
A stiffness-limited beam of fixed length may have any cross-section depth. Compare steel, aluminum, and Douglas fir using E 1 / 2 / ρ E^{1/2}/\rho E 1/2 / ρ .
Steel: 200,000 MPa 7,850 = 447.2 7,850 = 0.0570 \dfrac{\sqrt{200{,}000\ \text{MPa}}}{7{,}850} = \dfrac{447.2}{7{,}850} = 0.0570 7 , 850 200 , 000 MPa = 7 , 850 447.2 = 0.0570
Aluminum: 69,000 2,700 = 262.7 2,700 = 0.0973 \dfrac{\sqrt{69{,}000}}{2{,}700} = \dfrac{262.7}{2{,}700} = 0.0973 2 , 700 69 , 000 = 2 , 700 262.7 = 0.0973
Douglas fir: 13,000 500 = 114.0 500 = 0.228 \dfrac{\sqrt{13{,}000}}{500} = \dfrac{114.0}{500} = 0.228 500 13 , 000 = 500 114.0 = 0.228
Wood wins by a factor of 4 over steel and 2.3 over aluminum. This is the quantitative reason wood floor joists and aircraft spars (historically) and modern engineered lumber remain competitive: for a stiffness-limited beam whose depth is free, low density matters more than high modulus.
Note how the ranking reverses against the E / ρ E/\rho E / ρ table, where all three were tied near 25. Same three materials, same stiffness objective — but allowing the depth to change alters which index applies and therefore which material wins. Reading which variable is free is the entire skill.
Screening Constraints That Decide Real Selections
- Constraint Eliminates
- Service above ~150 °C Most thermoplastics
- Service above ~500 °C Aluminum, magnesium alloys
- Seawater / chloride exposure Carbon steel, 304 stainless in stagnant service
- Electrical insulation required All metals
- Cyclic loading with a required infinite life Aluminum (no true endurance limit)
- Impact loading at low temperature Ceramics, and ferritic steels below their transition temperature
- Food or potable water contact Lead-bearing alloys, many plasticized polymers
- Optical transparency Metals, most ceramics
The aluminum fatigue constraint is a favorite exam item. Steel exhibits a true endurance limit — a stress below which life is effectively infinite. Aluminum does not : its S-N curve keeps descending, so every aluminum part under cyclic load has a finite life and must be designed to a specified number of cycles. This is why aircraft structures have mandated inspection intervals and retirement lives, and it is a screening constraint no amount of specific-strength advantage can overcome.
Worked Example: Selecting a Pressure Vessel Material
A vessel must hold a chloride-bearing process fluid at 200 °C, resist cyclic pressure for 10 7 10^7 1 0 7 cycles, and minimize cost.
Screen:
- 200 °C eliminates thermoplastics and aluminum alloys (creep and strength loss)
- Chlorides at temperature eliminate 304 stainless (chloride stress corrosion cracking of austenitic grades)
10 7 10^7 1 0 7 cycles with a required infinite life favors a material with a genuine endurance limit → steel family
Ceramics are eliminated by their brittleness under cyclic pressure and thermal gradients
Surviving candidates: carbon steel with a corrosion-resistant lining or cladding, duplex stainless steel (much better chloride SCC resistance than austenitic grades), or a nickel alloy.
Rank on cost: clad carbon steel is typically the least expensive, duplex intermediate, nickel alloy highest.
Select clad carbon steel , with duplex as the alternative if cladding integrity or inspection access is a concern.
Note that no material index was needed . Four screening constraints reduced the entire materials universe to three candidates, and cost decided among them. That is how most real selections proceed, and why screening deserves the attention that ranking usually gets.