Study guide

10.6 Beam Deflections and Combined Axial/Bending Loading

FE Other Disciplines Fundamentals of Engineering

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Strategy

About the FE Other Disciplines Exam How to Use This Study Guide

2 Chapter 1: Mathematics

1.1 Analytic Geometry, Trigonometry, and Vector Operations 1.2 Differential and Integral Calculus 1.3 Ordinary Differential Equations and Laplace Transforms 1.4 Linear Algebra, Matrices, and Systems of Equations 1.5 Numerical Methods, Root-Finding, and Numerical Integration

3 Chapter 2: Probability and Statistics

2.1 Probability Distributions, PMFs, and PDFs 2.2 Expected Value, Mean, Variance, and Descriptive Statistics 2.3 Estimation, Confidence Intervals, and Sample Sizes 2.4 Hypothesis Testing, Goodness of Fit, and Linear Regression

4 Chapter 3: Chemistry

3.1 Stoichiometry, Chemical Reactions, and Solutions 3.2 Chemical Equilibrium, Acids/Bases, and Ideal Gas Laws 3.3 Oxidation-Reduction, Electrochemistry, and Corrosion Basics

5 Chapter 4: Instrumentation and Controls

4.1 Sensors, Transducers, and Signal Conditioning 4.2 Data Sampling, Accuracy/Precision, and A/D Conversion 4.3 Logic Diagrams, Boolean Algebra, and Control Logic

6 Chapter 5: Engineering Ethics and Societal Impacts

5.1 NCEES Model Rules of Professional Conduct and Codes of Ethics 5.2 Public Protection, Licensure Boards, and Professional Liability 5.3 Societal Impacts: Sustainability, Life-Cycle Analysis, and Public Safety

7 Chapter 6: Safety, Health, and Environment

6.1 OSHA Regulations, Industrial Hygiene, and PPE 6.2 Hazard Assessment, Risk Management, and Environmental Rules 6.3 Gas Detection and Monitoring 6.4 Electrical Safety 6.5 Confined Space Entry and Ventilation Rates

8 Chapter 7: Engineering Economics

7.1 Time Value of Money, Interest Formulas, and Cash Flow Diagrams 7.2 Capital Budgeting: Present Worth, Annual Worth, IRR, and B/C Ratio 7.3 Depreciation Methods, Income Taxes, and Breakeven Analysis 7.4 Cost Analysis, Uncertainty, Expected Value, and Decision Trees

9 Chapter 8: Statics

8.1 Statics Equilibrium, Free-Body Diagrams, and Force Systems 8.2 Distributed Loads, Resultants, and Equivalent Force-Couple Systems 8.3 Internal Forces in Rigid Bodies: Trusses, Frames, Machines, and Friction 8.4 Three-Dimensional Equilibrium, Cables, and Pulley Systems 8.5 Area Properties: Centroids, Moments of Inertia, and Radius of Gyration 8.6 Weight, Mass, and Force Units: slug, lbm, lbf, and g_c

10 Chapter 9: Dynamics

9.1 Kinematics of Particles and Rigid Bodies 9.2 Newton's Second Law for Particles and Rigid Bodies 9.3 Angular Motion, Torque, and Mass Moment of Inertia 9.4 Work-Energy Principle, Power, and Efficiency 9.5 Impulse-Momentum, Impact, and Coefficient of Restitution 9.6 Dynamic Friction and Vibrations: Natural Frequency and Damping

11 Chapter 10: Strength of Materials

10.1 Stress Types, Axial Stress-Strain, and Thermal Deformation 10.2 Torsion of Circular Shafts, Polar Moment, and Angle of Twist 10.3 Shear and Moment Diagrams 10.4 Flexural Bending Stress and Transverse Shear Stress 10.5 Stress Transformations, Principal Stresses, and Mohr's Circle 10.6 Beam Deflections and Combined Axial/Bending Loading 10.7 Column Buckling (Euler Formula) and Yield/Failure Criteria

12 Chapter 11: Materials

11.1 Crystal Structure, Phase Diagrams, and Material Processing 11.2 Mechanical Properties, Fatigue, Fracture, and Corrosion 11.3 Thermal Properties of Materials 11.4 Electrical and Chemical Properties of Materials 11.5 Material Selection for Engineering Design

13 Chapter 12: Fluid Mechanics

12.1 Fluid Properties, Hydrostatic Pressure, and Manometry 12.2 Dimensionless Numbers and Flow Regimes 12.3 Continuity Equation, Bernoulli Equation, and Energy Equation 12.4 Impulse-Momentum Equation and Forces on Control Volumes 12.5 Flow in Pipes, Friction Factors (Moody Diagram), and Head Losses 12.6 Turbomachinery: Pumps, Turbines, Fans, and Compressors 12.7 Open-Channel Flow, Manning's Equation, and Drag 12.8 Fluid Transport Systems and Flow Measurement 12.9 Ideal Gas Law, Gas Mixtures, and the Real Gas Law

14 Chapter 13: Basic Electrical Engineering

13.1 Electrical Fundamentals, Ohm's Law, and DC Circuits 13.2 AC Circuits, Phasors, Impedance, and Three-Phase Power 13.3 Magnetic Fields, Induction, Transformers, and Motor Efficiency 13.4 Electrical Measuring Devices: Voltmeter, Ammeter, and Wattmeter

15 Chapter 14: Thermodynamics and Heat Transfer

14.1 First & Second Laws of Thermodynamics and Pure Substance Properties 14.2 Thermodynamic Processes and Property Diagrams (T-s, P-h, P-v) 14.3 Heat Transfer: Conduction, Convection, and Radiation 14.4 Ideal Gas Processes and Power/Refrigeration Cycles 14.5 Mass and Energy Balances on Control Volumes 14.6 Combustion and Combustion Products 14.7 Psychrometrics: Relative Humidity, Wet-Bulb Temperature, and the Psychrometric Chart

10.6 Beam Deflections and Combined Axial/Bending Loading

Key Takeaways Explain This Topic AI

The differential equation for elastic beam deflection is E I ( d 2 v / d x 2 ) = M ( x ) EI (d^2 v / dx^2) = M(x) E I ( d 2 v / d x 2 ) = M ( x ) , solved via double integration with specific kinematic boundary conditions.

Superposition allows complex beam deflections and stress distributions to be evaluated by summing standard load solutions from the NCEES FE Reference Handbook.

Combined axial force and bending moments yield normal stress distributions σ = ± P / A ± M y / I \sigma = \pm P/A \pm My/I σ = ± P / A ± M y / I ; eccentric axial loading P P P creates an equivalent bending moment M = P ⋅ e M = P \cdot e M = P ⋅ e .

Thin-walled pressure vessels under internal gauge pressure p p p experience hoop stress σ h = p r / t \sigma_h = pr/t σ h ​ = p r / t and longitudinal stress σ a = p r / ( 2 t ) \sigma_a = pr/(2t) σ a ​ = p r / ( 2 t ) for cylinders, and σ = p r / ( 2 t ) \sigma = pr/(2t) σ = p r / ( 2 t ) for spheres.

Last updated: August 2026

10.6 Beam Deflections and Combined Axial/Bending Loading

Core Engineering Principle: Structural components in practice are rarely subjected to isolated single loads. Engineers must evaluate deflections using elastic differential equations and analyze combined normal and shear stress states produced by concurrent axial, flexural, torsional, and pressure loadings.

Elastic Beam Deflection: Double Integration Method

For a prismatic elastic beam with flexural rigidity E I E I E I subjected to transverse loads, the relationship between internal bending moment M ( x ) M(x) M ( x ) and transverse deflection v ( x ) v(x) v ( x ) is governed by the second-order linear differential equation: E I d 2 v d x 2 = M ( x ) E I \frac{d^2 v}{dx^2} = M(x) E I d x 2 d 2 v ​ = M ( x )

Integrating once yields the equation for beam slope θ ( x ) = d v d x \theta(x) = \frac{dv}{dx} θ ( x ) = d x d v ​ : E I d v d x = ∫ M ( x ) d x + C 1 E I \frac{dv}{dx} = \int M(x) dx + C_1 E I d x d v ​ = ∫ M ( x ) d x + C 1 ​

Integrating a second time yields the transverse deflection profile v ( x ) v(x) v ( x ) : E I v ( x ) = ∬ M ( x ) d x 2 + C 1 x + C 2 E I v(x) = \iint M(x) dx^2 + C_1 x + C_2 E I v ( x ) = ∬ M ( x ) d x 2 + C 1 ​ x + C 2 ​

The integration constants C 1 C_1 C 1 ​ and C 2 C_2 C 2 ​ are evaluated using physical Boundary Conditions at support locations.

Support Type Physical Constraint Boundary Conditions

Pin / Roller Support (at x = a x = a x = a ) Prevents vertical displacement v ( a ) = 0 v(a) = 0 v ( a ) = 0 (Slope θ ( a ) ≠ 0 \theta(a) \ne 0 θ ( a )  = 0 )

Fixed Support (Cantilever Root) (at x = a x = a x = a ) Prevents displacement & rotation v ( a ) = 0 v(a) = 0 v ( a ) = 0 and θ ( a ) = d v d x ∣ x = a = 0 \theta(a) = \left.\frac{dv}{dx}\right\vert_{x=a} = 0 θ ( a ) = d x d v ​ ​ x = a ​ = 0

Free End (at x = a x = a x = a ) Zero moment & zero shear force M ( a ) = 0 M(a) = 0 M ( a ) = 0 and V ( a ) = 0 V(a) = 0 V ( a ) = 0

Guided / Sliding Support (at x = a x = a x = a ) Prevents rotation, allows deflection θ ( a ) = 0 \theta(a) = 0 θ ( a ) = 0 (Shear V ( a ) = 0 V(a) = 0 V ( a ) = 0 )

Superposition Method for Beam Deflections

Because the elastic governing differential equation is linear, the total deflection or slope caused by multiple transverse loads equals the algebraic sum of the deflections or slopes caused by each individual load acting separately.

Standard FE Exam Beam Deflection Formulas

Below are standard beam deflection equations compiled from the NCEES FE Reference Handbook:

Beam Configuration & Loading Maximum Deflection ( v m a x v_{max} v ma x ​ ) Location of v m a x v_{max} v ma x ​ Maximum Slope ( θ m a x \theta_{max} θ ma x ​ )

Cantilever Beam , Tip Concentrated Load P P P v m a x = P L 3 3 E I v_{max} = \frac{P L^3}{3 E I} v ma x ​ = 3 E I P L 3 ​ Free tip ( x = L x = L x = L ) θ m a x = P L 2 2 E I \theta_{max} = \frac{P L^2}{2 E I} θ ma x ​ = 2 E I P L 2 ​

Cantilever Beam , Uniform Load w w w v m a x = w L 4 8 E I v_{max} = \frac{w L^4}{8 E I} v ma x ​ = 8 E I w L 4 ​ Free tip ( x = L x = L x = L ) θ m a x = w L 3 6 E I \theta_{max} = \frac{w L^3}{6 E I} θ ma x ​ = 6 E I w L 3 ​

Simply Supported Beam , Center Point Load P P P v m a x = P L 3 48 E I v_{max} = \frac{P L^3}{48 E I} v ma x ​ = 48 E I P L 3 ​ Midspan ( x = L / 2 x = L/2 x = L /2 ) θ m a x = P L 2 16 E I \theta_{max} = \frac{P L^2}{16 E I} θ ma x ​ = 16 E I P L 2 ​ (at ends)

Simply Supported Beam , Uniform Load w w w v m a x = 5 w L 4 384 E I v_{max} = \frac{5 w L^4}{384 E I} v ma x ​ = 384 E I 5 w L 4 ​ Midspan ( x = L / 2 x = L/2 x = L /2 ) θ m a x = w L 3 24 E I \theta_{max} = \frac{w L^3}{24 E I} θ ma x ​ = 24 E I w L 3 ​ (at ends)

Exam Tip: Ensure consistency of units when using beam formulas. If E E E is in Pa ( N/m 2 \text{N/m}^2 N/m 2 ), I I I must be in m 4 \text{m}^4 m 4 , L L L in m \text{m} m , and P P P in N \text{N} N , yielding deflection v v v in meters.

Combined Axial and Bending Loading & Eccentricity

When a structural member is subjected simultaneously to an axial load P P P and bending moments M y M_y M y ​ and M z M_z M z ​ , normal stresses superimpose linearly: σ t o t a l = ± P A ± M z y I z ± M y z I y \sigma_{total} = \pm \frac{P}{A} \pm \frac{M_z y}{I_z} \pm \frac{M_y z}{I_y} σ t o t a l ​ = ± A P ​ ± I z ​ M z ​ y ​ ± I y ​ M y ​ z ​

Eccentric Axial Loading

An axial force P P P applied at an eccentricity distance e e e from the centroidal axis of a column cross-section is equivalent to a concentric axial force P P P plus a couple moment M = P ⋅ e M = P \cdot e M = P ⋅ e .

The combined normal stress profile across the section depth is: σ = − P A ± ( P e ) c I = − P A ( 1 ± e c k 2 ) \sigma = - \frac{P}{A} \pm \frac{(P e) c}{I} = - \frac{P}{A} \left( 1 \pm \frac{e c}{k^2} \right) σ = − A P ​ ± I ( P e ) c ​ = − A P ​ ( 1 ± k 2 ec ​ )

where k = I / A k = \sqrt{I/A} k = I / A ​ is the Radius of Gyration of the cross-section.

Kern of a Cross-Section (Middle Third Rule)

For brittle or unreinforced materials (such as masonry, concrete, or soil foundations) that cannot resist tension, the eccentric load P P P must remain within a central region called the Kern so that no tensile normal stresses develop anywhere on the cross-section.

For a solid rectangular cross-section of width b b b and depth h h h , the load eccentricity must satisfy: ≠ ≤ h 6 \ne \le \frac{h}{6}  = ≤ 6 h ​

This requirement is known as the Middle Third Rule (the resultant load must fall within the middle third of the cross-sectional depth).

Thin-Walled Pressure Vessels

A vessel is classified as thin-walled if the ratio of inner radius r r r to wall thickness t t t satisfies r t ≥ 10 \frac{r}{t} \ge 10 t r ​ ≥ 10 . Under internal gauge pressure p p p , radial stress through the wall thickness is negligible, creating a state of plane stress in the vessel wall.

Cylindrical Pressure Vessels

Hoop (Circumferential) Stress ( σ h \sigma_h σ h ​ ): Acts tangentially along the circumference: σ h = p r t \sigma_h = \frac{p r}{t} σ h ​ = t p r ​

Longitudinal (Axial) Stress ( σ a \sigma_a σ a ​ ): Acts parallel to the longitudinal cylinder axis: σ a = p r 2 t \sigma_a = \frac{p r}{2 t} σ a ​ = 2 t p r ​

Notice that hoop stress is exactly twice the magnitude of longitudinal stress ( σ h = 2 σ a \sigma_h = 2 \sigma_a σ h ​ = 2 σ a ​ ). Consequently, cylindrical pressure vessels under excess pressure tend to burst along longitudinal seams.

Spherical Pressure Vessels

Due to spherical symmetry, normal stress is identical in all tangential directions: σ 1 = σ 2 = p r 2 t \sigma_1 = \sigma_2 = \frac{p r}{2 t} σ 1 ​ = σ 2 ​ = 2 t p r ​

Vessel Geometry Maximum In-Plane Stress In-Plane Shear Stress Absolute Max Shear Stress ( τ a b s , m a x \tau_{abs, max} τ ab s , ma x ​ )

Thin Cylinder σ h = p r t \sigma_h = \frac{p r}{t} σ h ​ = t p r ​ τ i n − p l a n e = σ h − σ a 2 = p r 4 t \tau_{in-plane} = \frac{\sigma_h - \sigma_a}{2} = \frac{p r}{4 t} τ in − pl an e ​ = 2 σ h ​ − σ a ​ ​ = 4 t p r ​ τ a b s , m a x = σ h − 0 2 = p r 2 t \tau_{abs, max} = \frac{\sigma_h - 0}{2} = \frac{p r}{2 t} τ ab s , ma x ​ = 2 σ h ​ − 0 ​ = 2 t p r ​

Thin Sphere σ = p r 2 t \sigma = \frac{p r}{2 t} σ = 2 t p r ​ τ i n − p l a n e = 0 \tau_{in-plane} = 0 τ in − pl an e ​ = 0 τ a b s , m a x = σ − 0 2 = p r 4 t \tau_{abs, max} = \frac{\sigma - 0}{2} = \frac{p r}{4 t} τ ab s , ma x ​ = 2 σ − 0 ​ = 4 t p r ​

  • Worked Engineering Problems
  • Problem 1: Combined Eccentric Axial Load on a Column

Scenario: A short rectangular concrete column ( b = 300 mm = 0.30 m b = 300\text{ mm} = 0.30\text{ m} b = 300 mm = 0.30 m , h = 400 mm = 0.40 m h = 400\text{ mm} = 0.40\text{ m} h = 400 mm = 0.40 m ) carries a vertical compressive axial load P = 480 kN P = 480\text{ kN} P = 480 kN applied at an eccentricity e = 60 mm = 0.06 m e = 60\text{ mm} = 0.06\text{ m} e = 60 mm = 0.06 m from the geometric centroid along the principal h h h -axis. Calculate (a) the cross-sectional area A A A , (b) moment of inertia I x I_x I x ​ , (c) equivalent bending moment M M M , and (d) maximum compressive and tensile normal stresses at the extreme cross-sectional fibers.

Solution:

Calculate sectional properties: A = b h = ( 0.30 m ) ( 0.40 m ) = 0.12 m 2 A = b h = (0.30\text{ m})(0.40\text{ m}) = 0.12\text{ m}^2 A = bh = ( 0.30 m ) ( 0.40 m ) = 0.12 m 2 I x = b h 3 12 = ( 0.30 ) ( 0.40 ) 3 12 = ( 0.30 ) ( 0.064 ) 12 = 0.0016 m 4 I_x = \frac{b h^3}{12} = \frac{(0.30)(0.40)^3}{12} = \frac{(0.30)(0.064)}{12} = 0.0016\text{ m}^4 I x ​ = 12 b h 3 ​ = 12 ( 0.30 ) ( 0.40 ) 3 ​ = 12 ( 0.30 ) ( 0.064 ) ​ = 0.0016 m 4 c = h 2 = 0.20 m c = \frac{h}{2} = 0.20\text{ m} c = 2 h ​ = 0.20 m S x = I x c = 0.0016 0.20 = 0.008 m 3 S_x = \frac{I_x}{c} = \frac{0.0016}{0.20} = 0.008\text{ m}^3 S x ​ = c I x ​ ​ = 0.20 0.0016 ​ = 0.008 m 3

Calculate direct axial stress component (compressive): σ a x i a l = − P A = − 480 , 000 N 0.12 m 2 = − 4 , 000 , 000 Pa = − 4.0 MPa \sigma_{axial} = - \frac{P}{A} = - \frac{480,000\text{ N}}{0.12\text{ m}^2} = -4,000,000\text{ Pa} = -4.0\text{ MPa} σ a x ia l ​ = − A P ​ = − 0.12 m 2 480 , 000 N ​ = − 4 , 000 , 000 Pa = − 4.0 MPa

Calculate equivalent bending moment M M M and flexural stress component: M = P ⋅ e = ( 480 , 000 N ) ( 0.06 m ) = 28 , 800 N ⋅ m = 28.8 kN ⋅ m M = P \cdot e = (480,000\text{ N})(0.06\text{ m}) = 28,800\text{ N}\cdot\text{m} = 28.8\text{ kN}\cdot\text{m} M = P ⋅ e = ( 480 , 000 N ) ( 0.06 m ) = 28 , 800 N ⋅ m = 28.8 kN ⋅ m σ b e n d i n g = ± M S x = ± 28 , 800 N ⋅ m 0.008 m 3 = ± 3 , 600 , 000 Pa = ± 3.6 MPa \sigma_{bending} = \pm \frac{M}{S_x} = \pm \frac{28,800\text{ N}\cdot\text{m}}{0.008\text{ m}^3} = \pm 3,600,000\text{ Pa} = \pm 3.6\text{ MPa} σ b e n d in g ​ = ± S x ​ M ​ = ± 0.008 m 3 28 , 800 N ⋅ m ​ = ± 3 , 600 , 000 Pa = ± 3.6 MPa

Superimpose stresses at extreme fibers:

Highly Compressed Edge (same side as load eccentricity): σ m a x , c o m p = − 4.0 MPa − 3.6 MPa = − 7.6 MPa (compressive) \sigma_{max, comp} = -4.0\text{ MPa} - 3.6\text{ MPa} = -7.6\text{ MPa (compressive)} σ ma x , co m p ​ = − 4.0 MPa − 3.6 MPa = − 7.6 MPa (compressive)

Opposite Edge: σ o p p = − 4.0 MPa + 3.6 MPa = − 0.4 MPa (compressive) \sigma_{opp} = -4.0\text{ MPa} + 3.6\text{ MPa} = -0.4\text{ MPa (compressive)} σ o pp ​ = − 4.0 MPa + 3.6 MPa = − 0.4 MPa (compressive)

Since σ o p p = − 0.4 MPa < 0 \sigma_{opp} = -0.4\text{ MPa} < 0 σ o pp ​ = − 0.4 MPa < 0 , the entire cross-section remains under compression, consistent with e = 60 mm ≤ h 6 = 400 6 = 66.67 mm e = 60\text{ mm} \le \frac{h}{6} = \frac{400}{6} = 66.67\text{ mm} e = 60 mm ≤ 6 h ​ = 6 400 ​ = 66.67 mm .

Problem 2: Cylindrical Pressure Vessel under Combined Pressure and Torque

Scenario: A thin-walled cylindrical steel pressure tank with inner radius r = 0.50 m r = 0.50\text{ m} r = 0.50 m and wall thickness t = 10 mm = 0.01 m t = 10\text{ mm} = 0.01\text{ m} t = 10 mm = 0.01 m is pressurized to internal gauge pressure p = 2.0 MPa p = 2.0\text{ MPa} p = 2.0 MPa . Simultaneously, a torque T = 50 kN ⋅ m T = 50\text{ kN}\cdot\text{m} T = 50 kN ⋅ m is applied to the tank. Determine (a) hoop stress σ h \sigma_h σ h ​ , (b) longitudinal stress σ a \sigma_a σ a ​ , (c) torsional shear stress τ x y \tau_{xy} τ x y ​ , and (d) maximum principal stress σ 1 \sigma_1 σ 1 ​ .

Solution:

Calculate pressure stress components: σ h = p r t = ( 2.0 × 10 6 Pa ) ( 0.50 m ) 0.01 m = 100.0 MPa \sigma_h = \frac{p r}{t} = \frac{(2.0 \times 10^6\text{ Pa})(0.50\text{ m})}{0.01\text{ m}} = 100.0\text{ MPa} σ h ​ = t p r ​ = 0.01 m ( 2.0 × 1 0 6 Pa ) ( 0.50 m ) ​ = 100.0 MPa σ a = p r 2 t = 100.0 2 = 50.0 MPa \sigma_a = \frac{p r}{2 t} = \frac{100.0}{2} = 50.0\text{ MPa} σ a ​ = 2 t p r ​ = 2 100.0 ​ = 50.0 MPa

Calculate torsional shear stress τ x y \tau_{xy} τ x y ​ using thin-walled tube formula τ = T 2 π r 2 t \tau = \frac{T}{2 \pi r^2 t} τ = 2 π r 2 t T ​ : τ x y = 50 , 000 N ⋅ m 2 π ( 0.50 m ) 2 ( 0.01 m ) = 50 , 000 2 π ( 0.25 ) ( 0.01 ) = 50 , 000 0.015708 = 3 , 183 , 099 Pa ≈ 3.18 MPa \tau_{xy} = \frac{50,000\text{ N}\cdot\text{m}}{2 \pi (0.50\text{ m})^2 (0.01\text{ m})} = \frac{50,000}{2 \pi (0.25)(0.01)} = \frac{50,000}{0.015708} = 3,183,099\text{ Pa} \approx 3.18\text{ MPa} τ x y ​ = 2 π ( 0.50 m ) 2 ( 0.01 m ) 50 , 000 N ⋅ m ​ = 2 π ( 0.25 ) ( 0.01 ) 50 , 000 ​ = 0.015708 50 , 000 ​ = 3 , 183 , 099 Pa ≈ 3.18 MPa

Calculate principal stress σ 1 \sigma_1 σ 1 ​ via 2D transformation with σ x = σ a = 50 \sigma_x = \sigma_a = 50 σ x ​ = σ a ​ = 50 , σ y = σ h = 100 \sigma_y = \sigma_h = 100 σ y ​ = σ h ​ = 100 , τ x y = 3.18 \tau_{xy} = 3.18 τ x y ​ = 3.18 : σ a v g = 50 + 100 2 = 75.0 MPa \sigma_{avg} = \frac{50 + 100}{2} = 75.0\text{ MPa} σ a vg ​ = 2 50 + 100 ​ = 75.0 MPa R = ( 50 − 100 2 ) 2 + ( 3.18 ) 2 = ( − 25 ) 2 + 10.11 = 625 + 10.11 = 635.11 = 25.20 MPa R = \sqrt{\left(\frac{50 - 100}{2}\right)^2 + (3.18)^2} = \sqrt{(-25)^2 + 10.11} = \sqrt{625 + 10.11} = \sqrt{635.11} = 25.20\text{ MPa} R = ( 2 50 − 100 ​ ) 2 + ( 3.18 ) 2 ​ = ( − 25 ) 2 + 10.11 ​ = 625 + 10.11 ​ = 635.11 ​ = 25.20 MPa σ 1 = σ a v g + R = 75.0 + 25.20 = 100.20 MPa \sigma_1 = \sigma_{avg} + R = 75.0 + 25.20 = 100.20\text{ MPa} σ 1 ​ = σ a vg ​ + R = 75.0 + 25.20 = 100.20 MPa