Study guide
10.5 Stress Transformations, Principal Stresses, and Mohr's Circle
FE Other Disciplines Fundamentals of Engineering
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Exam Strategy
About the FE Other Disciplines Exam How to Use This Study Guide
2 Chapter 1: Mathematics
1.1 Analytic Geometry, Trigonometry, and Vector Operations 1.2 Differential and Integral Calculus 1.3 Ordinary Differential Equations and Laplace Transforms 1.4 Linear Algebra, Matrices, and Systems of Equations 1.5 Numerical Methods, Root-Finding, and Numerical Integration
3 Chapter 2: Probability and Statistics
2.1 Probability Distributions, PMFs, and PDFs 2.2 Expected Value, Mean, Variance, and Descriptive Statistics 2.3 Estimation, Confidence Intervals, and Sample Sizes 2.4 Hypothesis Testing, Goodness of Fit, and Linear Regression
4 Chapter 3: Chemistry
3.1 Stoichiometry, Chemical Reactions, and Solutions 3.2 Chemical Equilibrium, Acids/Bases, and Ideal Gas Laws 3.3 Oxidation-Reduction, Electrochemistry, and Corrosion Basics
5 Chapter 4: Instrumentation and Controls
4.1 Sensors, Transducers, and Signal Conditioning 4.2 Data Sampling, Accuracy/Precision, and A/D Conversion 4.3 Logic Diagrams, Boolean Algebra, and Control Logic
6 Chapter 5: Engineering Ethics and Societal Impacts
5.1 NCEES Model Rules of Professional Conduct and Codes of Ethics 5.2 Public Protection, Licensure Boards, and Professional Liability 5.3 Societal Impacts: Sustainability, Life-Cycle Analysis, and Public Safety
7 Chapter 6: Safety, Health, and Environment
6.1 OSHA Regulations, Industrial Hygiene, and PPE 6.2 Hazard Assessment, Risk Management, and Environmental Rules 6.3 Gas Detection and Monitoring 6.4 Electrical Safety 6.5 Confined Space Entry and Ventilation Rates
8 Chapter 7: Engineering Economics
7.1 Time Value of Money, Interest Formulas, and Cash Flow Diagrams 7.2 Capital Budgeting: Present Worth, Annual Worth, IRR, and B/C Ratio 7.3 Depreciation Methods, Income Taxes, and Breakeven Analysis 7.4 Cost Analysis, Uncertainty, Expected Value, and Decision Trees
9 Chapter 8: Statics
8.1 Statics Equilibrium, Free-Body Diagrams, and Force Systems 8.2 Distributed Loads, Resultants, and Equivalent Force-Couple Systems 8.3 Internal Forces in Rigid Bodies: Trusses, Frames, Machines, and Friction 8.4 Three-Dimensional Equilibrium, Cables, and Pulley Systems 8.5 Area Properties: Centroids, Moments of Inertia, and Radius of Gyration 8.6 Weight, Mass, and Force Units: slug, lbm, lbf, and g_c
10 Chapter 9: Dynamics
9.1 Kinematics of Particles and Rigid Bodies 9.2 Newton's Second Law for Particles and Rigid Bodies 9.3 Angular Motion, Torque, and Mass Moment of Inertia 9.4 Work-Energy Principle, Power, and Efficiency 9.5 Impulse-Momentum, Impact, and Coefficient of Restitution 9.6 Dynamic Friction and Vibrations: Natural Frequency and Damping
11 Chapter 10: Strength of Materials
10.1 Stress Types, Axial Stress-Strain, and Thermal Deformation 10.2 Torsion of Circular Shafts, Polar Moment, and Angle of Twist 10.3 Shear and Moment Diagrams 10.4 Flexural Bending Stress and Transverse Shear Stress 10.5 Stress Transformations, Principal Stresses, and Mohr's Circle 10.6 Beam Deflections and Combined Axial/Bending Loading 10.7 Column Buckling (Euler Formula) and Yield/Failure Criteria
12 Chapter 11: Materials
11.1 Crystal Structure, Phase Diagrams, and Material Processing 11.2 Mechanical Properties, Fatigue, Fracture, and Corrosion 11.3 Thermal Properties of Materials 11.4 Electrical and Chemical Properties of Materials 11.5 Material Selection for Engineering Design
13 Chapter 12: Fluid Mechanics
12.1 Fluid Properties, Hydrostatic Pressure, and Manometry 12.2 Dimensionless Numbers and Flow Regimes 12.3 Continuity Equation, Bernoulli Equation, and Energy Equation 12.4 Impulse-Momentum Equation and Forces on Control Volumes 12.5 Flow in Pipes, Friction Factors (Moody Diagram), and Head Losses 12.6 Turbomachinery: Pumps, Turbines, Fans, and Compressors 12.7 Open-Channel Flow, Manning's Equation, and Drag 12.8 Fluid Transport Systems and Flow Measurement 12.9 Ideal Gas Law, Gas Mixtures, and the Real Gas Law
14 Chapter 13: Basic Electrical Engineering
13.1 Electrical Fundamentals, Ohm's Law, and DC Circuits 13.2 AC Circuits, Phasors, Impedance, and Three-Phase Power 13.3 Magnetic Fields, Induction, Transformers, and Motor Efficiency 13.4 Electrical Measuring Devices: Voltmeter, Ammeter, and Wattmeter
15 Chapter 14: Thermodynamics and Heat Transfer
14.1 First & Second Laws of Thermodynamics and Pure Substance Properties 14.2 Thermodynamic Processes and Property Diagrams (T-s, P-h, P-v) 14.3 Heat Transfer: Conduction, Convection, and Radiation 14.4 Ideal Gas Processes and Power/Refrigeration Cycles 14.5 Mass and Energy Balances on Control Volumes 14.6 Combustion and Combustion Products 14.7 Psychrometrics: Relative Humidity, Wet-Bulb Temperature, and the Psychrometric Chart
10.5 Stress Transformations, Principal Stresses, and Mohr's Circle
Key Takeaways Explain This Topic AI
2D plane stress transformation formulas convert normal stresses ( σ x , σ y ) (\sigma_x, \sigma_y) ( σ x , σ y ) and shear stress τ x y \tau_{xy} τ x y to an inclined plane oriented at angle θ \theta θ .
Principal stresses σ 1 \sigma_1 σ 1 and σ 2 \sigma_2 σ 2 represent the maximum and minimum normal stresses acting on principal planes where shear stress is zero ( τ = 0 \tau = 0 τ = 0 ).
The radius of Mohr's Circle R = ( ( σ x − σ y ) / 2 ) 2 + τ x y 2 R = \sqrt{(( \sigma_x - \sigma_y ) / 2)^2 + \tau_{xy}^2} R = (( σ x − σ y ) /2 ) 2 + τ x y 2 equals the maximum in-plane shear stress τ m a x , i n − p l a n e \tau_{max, in-plane} τ ma x , in − pl an e .
Absolute maximum shear stress τ a b s , m a x \tau_{abs, max} τ ab s , ma x must consider out-of-plane principal stress σ 3 = 0 \sigma_3 = 0 σ 3 = 0 in 2D plane stress analysis when σ 1 \sigma_1 σ 1 and σ 2 \sigma_2 σ 2 share the same algebraic sign.
Last updated: August 2026
10.5 Stress Transformations, Principal Stresses, and Mohr's Circle
Core Engineering Principle: Stress at a point inside a loaded body varies depending on the orientation of the plane cut through that point. Stress transformation equations allow engineers to find critical principal normal stresses and maximum shear stresses necessary for structural design and failure assessment.
2D Plane Stress Transformation Equations
Consider a differential element in a state of plane stress (where σ z = 0 \sigma_z = 0 σ z = 0 , τ x z = 0 \tau_{xz} = 0 τ x z = 0 , τ y z = 0 \tau_{yz} = 0 τ yz = 0 ) subjected to normal stresses σ x \sigma_x σ x and σ y \sigma_y σ y and shear stress τ x y \tau_{xy} τ x y .
To determine normal stress σ x ′ \sigma_{x'} σ x ′ and shear stress τ x ′ y ′ \tau_{x'y'} τ x ′ y ′ acting on an inclined plane rotated counterclockwise by an angle θ \theta θ from the x x x -axis, use the 2D Plane Stress Transformation Equations : σ x ′ = σ x + σ y 2 + σ x − σ y 2 cos 2 θ + τ x y sin 2 θ \sigma_{x'} = \frac{\sigma_x + \sigma_y}{2} + \frac{\sigma_x - \sigma_y}{2} \cos 2\theta + \tau_{xy} \sin 2\theta σ x ′ = 2 σ x + σ y + 2 σ x − σ y cos 2 θ + τ x y sin 2 θ σ y ′ = σ x + σ y 2 − σ x − σ y 2 cos 2 θ − τ x y sin 2 θ \sigma_{y'} = \frac{\sigma_x + \sigma_y}{2} - \frac{\sigma_x - \sigma_y}{2} \cos 2\theta - \tau_{xy} \sin 2\theta σ y ′ = 2 σ x + σ y − 2 σ x − σ y cos 2 θ − τ x y sin 2 θ τ x ′ y ′ = − ( σ x − σ y 2 ) sin 2 θ + τ x y cos 2 θ \tau_{x'y'} = - \left( \frac{\sigma_x - \sigma_y}{2} \right) \sin 2\theta + \tau_{xy} \cos 2\theta τ x ′ y ′ = − ( 2 σ x − σ y ) sin 2 θ + τ x y cos 2 θ
Stress Invariant
An important property of stress transformation is that the sum of normal stresses on any two perpendicular planes is constant (invariant): σ x ′ + σ y ′ = σ x + σ y = 2 σ a v g \sigma_{x'} + \sigma_{y'} = \sigma_x + \sigma_y = 2 \sigma_{avg} σ x ′ + σ y ′ = σ x + σ y = 2 σ a vg
where the average normal stress is: σ a v g = σ x + σ y 2 \sigma_{avg} = \frac{\sigma_x + \sigma_y}{2} σ a vg = 2 σ x + σ y
- Principal Stresses and Maximum In-Plane Shear Stress
- Principal Planes and Principal Stresses
Principal planes are planes of orientation θ p \theta_p θ p on which the shear stress vanishes completely ( τ x ′ y ′ = 0 \tau_{x'y'} = 0 τ x ′ y ′ = 0 ). Setting τ x ′ y ′ = 0 \tau_{x'y'} = 0 τ x ′ y ′ = 0 in the transformation equation yields the principal plane orientation formula: tan 2 θ p = 2 τ x y σ x − σ y \tan 2\theta_p = \frac{2 \tau_{xy}}{\sigma_x - \sigma_y} tan 2 θ p = σ x − σ y 2 τ x y
This equation yields two roots, θ p 1 \theta_{p1} θ p 1 and θ p 2 = θ p 1 + 90 ∘ \theta_{p2} = \theta_{p1} + 90^\circ θ p 2 = θ p 1 + 9 0 ∘ , defining two mutually perpendicular principal planes.
The corresponding maximum and minimum normal stresses acting on these planes are the Principal Stresses ( σ 1 , σ 2 ) (\sigma_1, \sigma_2) ( σ 1 , σ 2 ) : σ 1 , 2 = σ x + σ y 2 ± ( σ x − σ y 2 ) 2 + τ x y 2 = σ a v g ± R \sigma_{1,2} = \frac{\sigma_x + \sigma_y}{2} \pm \sqrt{\left( \frac{\sigma_x - \sigma_y}{2} \right)^2 + \tau_{xy}^2} = \sigma_{avg} \pm R σ 1 , 2 = 2 σ x + σ y ± ( 2 σ x − σ y ) 2 + τ x y 2 = σ a vg ± R
where σ 1 \sigma_1 σ 1 is the algebraically larger principal stress and σ 2 \sigma_2 σ 2 is the algebraically smaller principal stress.
Maximum In-Plane Shear Stress
The maximum in-plane shear stress τ m a x , i n − p l a n e \tau_{max, in-plane} τ ma x , in − pl an e occurs on planes rotated by θ s = θ p ± 45 ∘ \theta_s = \theta_p \pm 45^\circ θ s = θ p ± 4 5 ∘ relative to the principal planes: tan 2 θ s = − ( σ x − σ y 2 τ x y ) \tan 2\theta_s = - \left( \frac{\sigma_x - \sigma_y}{2 \tau_{xy}} \right) tan 2 θ s = − ( 2 τ x y σ x − σ y )
The magnitude of the maximum in-plane shear stress equals the radius R R R of Mohr's Circle: τ m a x , i n − p l a n e = R = ( σ x − σ y 2 ) 2 + τ x y 2 = σ 1 − σ 2 2 \tau_{max, in-plane} = R = \sqrt{\left( \frac{\sigma_x - \sigma_y}{2} \right)^2 + \tau_{xy}^2} = \frac{\sigma_1 - \sigma_2}{2} τ ma x , in − pl an e = R = ( 2 σ x − σ y ) 2 + τ x y 2 = 2 σ 1 − σ 2
Important Note: On planes of maximum in-plane shear stress, normal stresses are not zero ; a normal stress equal to σ a v g = σ x + σ y 2 \sigma_{avg} = \frac{\sigma_x + \sigma_y}{2} σ a vg = 2 σ x + σ y acts on both orthogonal faces.
Mohr's Circle for 2D Stress Analysis
Mohr's Circle is a geometric representation of 2D stress transformation equations. Points along the circle correspond to normal and shear stress states ( σ , τ ) (\sigma, \tau) ( σ , τ ) on planes of varying orientation θ \theta θ .
Construction Steps for Mohr's Circle
Establish Axes: Plot normal stress σ \sigma σ on the horizontal axis (tension positive to the right) and shear stress τ \tau τ on the vertical axis.
Locate Center ( C C C ): The center of the circle lies on the horizontal axis at C = ( σ a v g , 0 ) = ( σ x + σ y 2 , 0 ) C = (\sigma_{avg}, 0) = \left( \frac{\sigma_x + \sigma_y}{2}, 0 \right) C = ( σ a vg , 0 ) = ( 2 σ x + σ y , 0 ) .
Plot Reference Point ( X X X ): Plot point X X X corresponding to stress on the vertical x x x -face: X = ( σ x , − τ x y ) X = (\sigma_x, -\tau_{xy}) X = ( σ x , − τ x y ) (using standard sign convention where shear producing clockwise rotation of the element is plotted above/below based on coordinate definition).
Calculate Radius ( R R R ): The radius R R R is the distance from C C C to X X X : R = ( σ x − σ y 2 ) 2 + τ x y 2 R = \sqrt{\left( \frac{\sigma_x - \sigma_y}{2} \right)^2 + \tau_{xy}^2} R = ( 2 σ x − σ y ) 2 + τ x y 2
Draw Circle and Identify Critical Points:
Principal Stresses: Intersections with horizontal axis σ 1 = σ a v g + R \sigma_1 = \sigma_{avg} + R σ 1 = σ a vg + R and σ 2 = σ a v g − R \sigma_2 = \sigma_{avg} - R σ 2 = σ a vg − R .
Max In-Plane Shear: Top and bottom peaks of circle τ m a x , i n − p l a n e = R \tau_{max, in-plane} = R τ ma x , in − pl an e = R .
Angle Mapping: A physical element rotation of angle θ \theta θ corresponds to an angular sweep of 2 θ 2\theta 2 θ in the same rotational direction on Mohr's Circle.
Absolute Maximum Shear Stress ( τ a b s , m a x \tau_{abs, max} τ ab s , ma x )
In 3D stress analysis, three principal stresses exist: σ 1 ≥ σ 2 ≥ σ 3 \sigma_1 \ge \sigma_2 \ge \sigma_3 σ 1 ≥ σ 2 ≥ σ 3 . For 2D plane stress, the third principal stress perpendicular to the plane is zero ( σ 3 = 0 \sigma_3 = 0 σ 3 = 0 ).
The Absolute Maximum Shear Stress τ a b s , m a x \tau_{abs, max} τ ab s , ma x is: τ a b s , m a x = σ m a x − σ m i n 2 = σ 1 − σ 3 2 \tau_{abs, max} = \frac{\sigma_{max} - \sigma_{min}}{2} = \frac{\sigma_1 - \sigma_3}{2} τ ab s , ma x = 2 σ ma x − σ min = 2 σ 1 − σ 3
2D Principal Stress Condition Relationship between σ 1 \sigma_1 σ 1 and σ 2 \sigma_2 σ 2 Absolute Maximum Shear Stress ( τ a b s , m a x \tau_{abs, max} τ ab s , ma x )
Opposite Signs σ 1 > 0 \sigma_1 > 0 σ 1 > 0 and σ 2 < 0 \sigma_2 < 0 σ 2 < 0 τ a b s , m a x = σ 1 − σ 2 2 = R \tau_{abs, max} = \frac{\sigma_1 - \sigma_2}{2} = R τ ab s , ma x = 2 σ 1 − σ 2 = R (In-plane governs)
Same Sign (Both Tension) σ 1 > 0 \sigma_1 > 0 σ 1 > 0 and σ 2 > 0 \sigma_2 > 0 σ 2 > 0 τ a b s , m a x = σ 1 − 0 2 = σ 1 2 \tau_{abs, max} = \frac{\sigma_1 - 0}{2} = \frac{\sigma_1}{2} τ ab s , ma x = 2 σ 1 − 0 = 2 σ 1 (Out-of-plane governs)
Same Sign (Both Compression) σ 1 < 0 \sigma_1 < 0 σ 1 < 0 and σ 2 < 0 \sigma_2 < 0 σ 2 < 0 τ a b s , m a x = 0 − σ 2 2 = ∣ σ 2 ∣ 2 \tau_{abs, max} = \frac{0 - \sigma_2}{2} = \frac{\vert\sigma_2\vert}{2} τ ab s , ma x = 2 0 − σ 2 = 2 ∣ σ 2 ∣ (Out-of-plane governs)
- Worked Engineering Problems
- Problem 1: Full 2D Stress Transformation & Principal Stresses
Scenario: A state of plane stress at a point in a structural steel bracket is given by σ x = 80 MPa \sigma_x = 80\text{ MPa} σ x = 80 MPa (tension), σ y = − 40 MPa \sigma_y = -40\text{ MPa} σ y = − 40 MPa (compression), and τ x y = 35 MPa \tau_{xy} = 35\text{ MPa} τ x y = 35 MPa . Calculate (a) average normal stress σ a v g \sigma_{avg} σ a vg , (b) Mohr's circle radius R R R , (c) principal stresses σ 1 \sigma_1 σ 1 and σ 2 \sigma_2 σ 2 , (d) principal plane orientation angle θ p \theta_p θ p , and (e) maximum in-plane shear stress τ m a x , i n − p l a n e \tau_{max, in-plane} τ ma x , in − pl an e .
Solution:
Calculate average normal stress σ a v g \sigma_{avg} σ a vg : σ a v g = σ x + σ y 2 = 80 + ( − 40 ) 2 = 40 2 = 20 MPa \sigma_{avg} = \frac{\sigma_x + \sigma_y}{2} = \frac{80 + (-40)}{2} = \frac{40}{2} = 20\text{ MPa} σ a vg = 2 σ x + σ y = 2 80 + ( − 40 ) = 2 40 = 20 MPa
Calculate Mohr's circle radius R R R : R = ( σ x − σ y 2 ) 2 + τ x y 2 = ( 80 − ( − 40 ) 2 ) 2 + ( 35 ) 2 R = \sqrt{\left( \frac{\sigma_x - \sigma_y}{2} \right)^2 + \tau_{xy}^2} = \sqrt{\left( \frac{80 - (-40)}{2} \right)^2 + (35)^2} R = ( 2 σ x − σ y ) 2 + τ x y 2 = ( 2 80 − ( − 40 ) ) 2 + ( 35 ) 2 R = ( 60 ) 2 + ( 35 ) 2 = 3600 + 1225 = 4825 = 69.46 MPa R = \sqrt{(60)^2 + (35)^2} = \sqrt{3600 + 1225} = \sqrt{4825} = 69.46\text{ MPa} R = ( 60 ) 2 + ( 35 ) 2 = 3600 + 1225 = 4825 = 69.46 MPa
Calculate principal normal stresses σ 1 \sigma_1 σ 1 and σ 2 \sigma_2 σ 2 : σ 1 = σ a v g + R = 20 + 69.46 = 89.46 MPa (tension) \sigma_1 = \sigma_{avg} + R = 20 + 69.46 = 89.46\text{ MPa (tension)} σ 1 = σ a vg + R = 20 + 69.46 = 89.46 MPa (tension) σ 2 = σ a v g − R = 20 − 69.46 = − 49.46 MPa (compression) \sigma_2 = \sigma_{avg} - R = 20 - 69.46 = -49.46\text{ MPa (compression)} σ 2 = σ a vg − R = 20 − 69.46 = − 49.46 MPa (compression)
Calculate principal plane orientation angle θ p \theta_p θ p : tan 2 θ p = 2 τ x y σ x − σ y = 2 ( 35 ) 80 − ( − 40 ) = 70 120 = 0.58333 \tan 2\theta_p = \frac{2 \tau_{xy}}{\sigma_x - \sigma_y} = \frac{2(35)}{80 - (-40)} = \frac{70}{120} = 0.58333 tan 2 θ p = σ x − σ y 2 τ x y = 80 − ( − 40 ) 2 ( 35 ) = 120 70 = 0.58333 2 θ p = arctan ( 0.58333 ) = 30.26 ∘ ⟹ θ p 1 = 15.13 ∘ 2\theta_p = \arctan(0.58333) = 30.26^\circ \implies \theta_{p1} = 15.13^\circ 2 θ p = arctan ( 0.58333 ) = 30.2 6 ∘ ⟹ θ p 1 = 15.1 3 ∘
Maximum in-plane shear stress: τ m a x , i n − p l a n e = R = 69.46 MPa \tau_{max, in-plane} = R = 69.46\text{ MPa} τ ma x , in − pl an e = R = 69.46 MPa
Problem 2: Stresses on an Inclined Plane (Weld Seam Analysis)
Scenario: A cylindrical pressure pipe has a spiral weld inclined at an angle θ = 30 ∘ \theta = 30^\circ θ = 3 0 ∘ relative to the transverse cross-sectional plane. The stress state relative to the pipe axes is σ x = 100 MPa \sigma_x = 100\text{ MPa} σ x = 100 MPa (axial tension), σ y = 40 MPa \sigma_y = 40\text{ MPa} σ y = 40 MPa (hoop tension), and τ x y = 0 MPa \tau_{xy} = 0\text{ MPa} τ x y = 0 MPa . Compute the normal stress σ x ′ \sigma_{x'} σ x ′ and shear stress τ x ′ y ′ \tau_{x'y'} τ x ′ y ′ acting directly across the welded seam.
Solution:
Identify input stresses and transformation angle: σ x = 100 MPa , σ y = 40 MPa , τ x y = 0 MPa , θ = 30 ∘ \sigma_x = 100\text{ MPa}, \quad \sigma_y = 40\text{ MPa}, \quad \tau_{xy} = 0\text{ MPa}, \quad \theta = 30^\circ σ x = 100 MPa , σ y = 40 MPa , τ x y = 0 MPa , θ = 3 0 ∘
Calculate parameters for transformation equations: σ a v g = 100 + 40 2 = 70 MPa , σ x − σ y 2 = 100 − 40 2 = 30 MPa \sigma_{avg} = \frac{100 + 40}{2} = 70\text{ MPa}, \quad \frac{\sigma_x - \sigma_y}{2} = \frac{100 - 40}{2} = 30\text{ MPa} σ a vg = 2 100 + 40 = 70 MPa , 2 σ x − σ y = 2 100 − 40 = 30 MPa 2 θ = 60 ∘ ⟹ cos 60 ∘ = 0.5 , sin 60 ∘ = 0.866025 2\theta = 60^\circ \implies \cos 60^\circ = 0.5, \quad \sin 60^\circ = 0.866025 2 θ = 6 0 ∘ ⟹ cos 6 0 ∘ = 0.5 , sin 6 0 ∘ = 0.866025
Calculate normal stress σ x ′ \sigma_{x'} σ x ′ across the weld: σ x ′ = σ a v g + ( σ x − σ y 2 ) cos 2 θ + τ x y sin 2 θ \sigma_{x'} = \sigma_{avg} + \left( \frac{\sigma_x - \sigma_y}{2} \right) \cos 2\theta + \tau_{xy} \sin 2\theta σ x ′ = σ a vg + ( 2 σ x − σ y ) cos 2 θ + τ x y sin 2 θ σ x ′ = 70 + ( 30 ) ( 0.5 ) + ( 0 ) ( 0.866025 ) = 70 + 15 = 85.0 MPa \sigma_{x'} = 70 + (30)(0.5) + (0)(0.866025) = 70 + 15 = 85.0\text{ MPa} σ x ′ = 70 + ( 30 ) ( 0.5 ) + ( 0 ) ( 0.866025 ) = 70 + 15 = 85.0 MPa
Calculate shear stress τ x ′ y ′ \tau_{x'y'} τ x ′ y ′ along the weld line: τ x ′ y ′ = − ( σ x − σ y 2 ) sin 2 θ + τ x y cos 2 θ \tau_{x'y'} = - \left( \frac{\sigma_x - \sigma_y}{2} \right) \sin 2\theta + \tau_{xy} \cos 2\theta τ x ′ y ′ = − ( 2 σ x − σ y ) sin 2 θ + τ x y cos 2 θ τ x ′ y ′ = − ( 30 ) ( 0.866025 ) + 0 = − 25.98 MPa \tau_{x'y'} = - (30)(0.866025) + 0 = -25.98\text{ MPa} τ x ′ y ′ = − ( 30 ) ( 0.866025 ) + 0 = − 25.98 MPa
Magnitude of shear stress along the seam is 25.98 MPa 25.98\text{ MPa} 25.98 MPa .