Study guide

1.1 DBPR Licensing, CILB Regulations & Journeyman Qualifications

Florida Journeyman Plumber Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Florida Plumbing Code Administration & Licensure

1.1 DBPR Licensing, CILB Regulations & Journeyman Qualifications 1.2 Permits, Inspections & Code Enforcement 1.3 Florida Construction Lien Law & Business Operations

2 Chapter 2: Sanitary Drainage Fundamentals & DFU Sizing

2.1 Gravity Drainage Principles & Florida DWV Materials 2.2 Drainage Fixture Units (DFU) & Load Values 2.3 Horizontal Branch & Vertical Stack Sizing 2.4 Drainage Fittings, Flow Direction & Change of Direction Rules

3 Chapter 3: Building Drains, Sewers & Special Drainage Systems

3.1 Building Drain & Building Sewer Sizing 3.2 Drainage Cleanouts: Sizing, Clearances & Locations 3.3 Sewage Ejectors, Sumps & Macerating Systems 3.4 Florida High Water Table, Slab Penetrations & Termite Protection

4 Chapter 4: Indirect Waste, Special Waste & Interceptors

4.1 Indirect Waste Systems: Air Gaps vs Air Breaks 4.2 Grease Interceptors: Hydromechanical & Gravity Interceptor Sizing 4.3 Sand, Oil & Specialized Interceptors

5 Chapter 5: Water Supply Systems & WSFU Pipe Sizing

5.1 Potable Water Piping Materials & Installation 5.2 Water Supply Fixture Units (WSFU) & Demand Estimations 5.3 Water Distribution Pipe Sizing Methods 5.4 Water Pressure Control, Boosting & PRVs

6 Chapter 6: Water Heaters, Cross-Connection Control & Reclaimed Water

6.1 Water Heaters & Safety Controls 6.2 Backflow Prevention & Cross-Connection Protection 6.3 Reclaimed Water Systems & Florida Dual-Plumbing Rules 6.4 System Testing, Disinfection & Commissioning

7 Chapter 7: DWV Venting Systems & Sizing

7.1 Principles of Venting & Trap Seal Integrity 7.2 Vent Sizing & Developed Length 7.3 Wet Venting & Horizontal Wet Venting 7.4 Circuit, Loop & Common Venting

8 Chapter 8: Specialized Venting & Air Admittance Valves

8.1 Island Fixture Vents & Foot Venting 8.2 Combination Waste and Vent Systems 8.3 Air Admittance Valves (AAVs) & Engineered Systems

9 Chapter 9: Isometric Drawing Interpretation & Drafting

9.1 Isometric Drawing Fundamentals and Plan Reading 9.2 Drafting Florida DWV Isometric Schematics 9.3 Local Exam Plan-Reading Practice and Self-Audit 9.4 Reading Plumbing Plans, Specifications & Schedules

10 Chapter 10: Fuel Gas Piping & Storm Drainage Systems

10.1 Fuel Gas Fundamentals: Natural Gas vs LP Gas 10.2 Gas Pipe Sizing & Demand Calculations 10.3 Gas Pipe Materials, Installation, Testing & Appliance Connections 10.4 Storm Drainage Sizing & Florida Rainfall Rates 10.5 Appliance Venting, Chimneys & Combustion Air

11 Chapter 11: Trade Mathematics, Accessibility & Jobsite Safety

11.1 Plumbing Math: Grade, Pitch & Elevation Calculations 11.2 Plumbing Math: 45-Degree & Rolling Offsets 11.3 Florida Accessibility Standards for Plumbing Fixtures 11.4 OSHA Construction Safety Standards for Plumbers 11.5 Plumbing Tools, Equipment & System Troubleshooting

12 Chapter 12: Medical Gas & Vacuum Piping Systems (NFPA 99)

12.1 Medical Gas Systems: Categories, Gases & Source Equipment 12.2 Medical Gas Piping Materials, Brazing & Nitrogen Purging 12.3 Station Outlets, Zone Valves, Alarms & Pipe Sizing 12.4 Medical-Surgical Vacuum, WAGD & System Verification

13 Chapter 13: Industrial, Process & Special-Waste Piping

13.1 Compressed Air & Industrial Gas Piping Systems 13.2 Industrial Vacuum Piping Systems 13.3 Process Piping & Steam Distribution Systems 13.4 Oil & Gasoline Storage and Distribution Systems 13.5 Industrial Water Drainage & Waste Pretreatment

14 Chapter 14: Site Utilities, Sewage Disposal & Water Mains

14.1 Onsite Sewage Treatment & Disposal: Septic Tanks & Drainfields 14.2 Sewage Lift Stations & Force Mains 14.3 Water Transmission Mains, Excavation & Heavy Equipment

15 Chapter 15: Pools, Wells, Irrigation, Solar & Fire Protection

15.1 Swimming Pool & Spa Piping Systems 15.2 Water Wells, Pumps & Irrigation Systems 15.3 Solar Water Heating Systems 15.4 Fire Protection Systems & Standpipes (NFPA 14)

1.1 DBPR Licensing, CILB Regulations & Journeyman Qualifications

Key Takeaways Explain This Topic AI

Florida Statutes Chapter 489 Part I establishes the Construction Industry Licensing Board (CILB) within the DBPR, dividing contractor oversight into Division I and Division II, with plumbing classified strictly under Division II.

Certified Plumbing Contractors hold statewide practice rights validated by DBPR examination, whereas Registered Plumbing Contractors hold local competency cards and may only practice within the issuing local jurisdiction and reciprocal localities.

Journeyman plumbers hold local competency credentials recognized under FS 489.1455 and must work under the employment and supervision of a licensed contractor; they cannot contract directly with property owners or pull permits.

Primary qualifying agents assume comprehensive operational, supervisory, and financial liability for the business organization, while secondary qualifying agents are liable only for projects they personally permit or supervise.

Contractors must complete 14 hours of board-approved continuing education biennially, while unlicensed contracting is penalized as a first-degree misdemeanor, elevated to a third-degree felony during a declared state of emergency.

Last updated: September 2026

DBPR Licensing, CILB Regulations & Journeyman Qualifications

In Florida, plumbing is governed by statutory mandates designed to protect the public health, safety, and welfare. Because defective plumbing systems pose immediate hazards—ranging from cross-connections contaminating potable drinking water to sewer gas asphyxiation and structural flooding—the State of Florida exercises rigorous regulatory oversight over all plumbing trade practitioners. For journeymen preparing for licensure or contractors establishing a practice, mastering the statutory framework in Florida Statutes (FS) Chapter 489, Part I and the administrative rules in Title 61G4 of the Florida Administrative Code (FAC) is an absolute professional requirement.

Statutory Framework: DBPR & CILB

The regulation of construction contracting across Florida flows from the executive branch through the Department of Business and Professional Regulation (DBPR) , established under FS Chapter 20 and governed by general licensing provisions in FS Chapter 455. Within the DBPR, regulatory authority over plumbing contracting is delegated to the Construction Industry Licensing Board (CILB) pursuant to FS Chapter 489, Part I.

Structure of the CILB

The CILB is an 18-member regulatory board appointed by the Governor and confirmed by the Florida Senate. The board is divided into two operational divisions:

Division I : Exercises jurisdiction over general contractors, building contractors, and residential contractors.

Division II : Exercises jurisdiction over trade-specific specialty contractors, including plumbing contractors , mechanical contractors, air conditioning contractors, roofing contractors, pool/spa contractors, underground utility and excavation contractors, and solar contractors.

Division II routinely investigates complaints, establishes minimum trade examination specifications, approves continuing education providers and curricula, evaluates financial responsibility and good moral character of applicants, and conducts disciplinary hearings for statutory violations.

Certified Contractor vs. Registered Contractor

Florida operates a dual-track contractor licensing system. Every plumbing contractor practicing in the state must be either Certified or Registered . Understanding the legal and operational differences between these two credentials is essential.

  • Regulatory Dimension Certified Plumbing Contractor (CFC) Registered Plumbing Contractor (RF)
  • Statutory Authority FS 489.113; FS 489.115 FS 489.117

Examination DBPR State Licensing Examination (Trade Knowledge + Business & Finance) Local municipal or county competency board examination

Geographic Scope of Practice Statewide practice across all 67 Florida counties and municipalities without additional local competency testing Restricted strictly to the specific county or municipality issuing the local competency card, plus reciprocal jurisdictions

Local Competency Card Required? No. Local building departments cannot require local testing or competency cards from certified contractors Yes. Must maintain an active local competency certificate as a condition precedent to state registration

State Registration Requirement Issued a direct state license by the CILB upon satisfying state requirements Must register the local competency credential with the DBPR/CILB to receive an "RF" registration number

Local Permitting Entitled to pull plumbing permits in any Florida jurisdiction upon presenting state license and insurance Can pull permits only within the boundaries of the issuing local jurisdiction and areas with formal reciprocity

Regulatory Oversight Subject to CILB discipline, state sanctions, and local disciplinary referral Subject to both local competency board discipline and CILB administrative action

The Certified Advantage

A Certified Plumbing Contractor (license prefix CFC ) can bid, contract, pull permits, and execute plumbing installations anywhere in the State of Florida. A county or municipality may require the certified contractor to register their state license, show proof of workers' compensation and general liability insurance, and pay a local administrative fee, but the local government is prohibited by state law from requiring local examinations or imposing additional competency hurdles.

The Registered Limitation

A Registered Plumbing Contractor (license prefix RF ) holds a local certificate of competency issued by a county or city licensing board (such as Miami-Dade, Broward, Hillsborough, or Duval). The contractor registers that local card with the DBPR. However, the registered contractor's legal practice is strictly confined to that local geographic territory. Practicing outside that designated territory without a formal interlocal reciprocity agreement constitutes illegal, unlicensed contracting under Florida law.

Journeyman Plumber Qualifications & Legal Status

A critical distinction on Florida licensing examinations is that the state CILB does not issue a statewide Journeyman Plumber license . The CILB licenses contractors (entities and individuals who enter into contracts with property owners). The regulation, examination, and issuance of Journeyman Plumber Competency Cards is delegated to local counties and municipalities pursuant to FS 489.1455 .

Journeyman Requirements Under Florida Law

Experience Prerequisites : Journeyman experience requirements are set by each county or municipal competency board, not by the state, so the number varies. Most Florida boards require on the order of four years of verified field experience as a registered plumbing apprentice or helper under the direct supervision of a licensed master or plumbing contractor. Because there is no statewide figure, always confirm the required years and documented hours with the specific local board you are applying to before assuming an hour count.

Competency Examination : Candidates must pass an approved proctored examination covering the Florida Building Code - Plumbing, pipe sizing, isometric drafting, drainage-waste-vent (DWV) systems, fuel gas, and safety standards.

Supervisory Relationship : Under FS 489.113, a journeyman plumber cannot contract directly with property owners, cannot submit bids, cannot advertise independent plumbing services, and cannot pull building permits .

Employment Status : A journeyman plumber must work as a W-2 employee or supervised technician under the direction, control, and employment of a certified or registered plumbing contractor.

Reciprocity Across Counties (FS 489.1455) : Florida law allows local jurisdictions to recognize journeyman licenses issued by other Florida counties or municipalities if the issuing jurisdiction required an approved exam and comparable experience. However, recognition is subject to local ordinance verification.

Qualifying Agents & Business Governance

A plumbing contracting business in Florida—whether organized as a corporation, limited liability company (LLC), or partnership—cannot independently hold a contractor's license. The business entity must be qualified by an individual licensed contractor designated as the Qualifying Agent under FS 489.119 and FS 489.1195 .

Primary Qualifying Agent vs. Secondary Qualifying Agent

Primary Qualifying Agent (PQA) :

Every licensed business organization must have at least one Primary Qualifying Agent.

The PQA exercises operational control, oversight, and direction over all plumbing construction activities undertaken by the entity.

The PQA bears joint and several financial responsibility for the entire business organization, including financial obligations, payroll, supplier debts, and regulatory compliance.

The PQA is responsible for ensuring that all permits are pulled, work is performed in compliance with the Florida Building Code, and jobsite safety is maintained.

Secondary Qualifying Agent (SQA) :

A business organization that already possesses a Primary Qualifying Agent may appoint one or more Secondary Qualifying Agents.

An SQA is legally and professionally responsible only for the specific construction projects where they personally pulled the building permit or were designated in writing as the supervising qualifier.

The SQA does not assume general financial liability for the broader business entity or other projects supervised by the PQA.

Supervision Standards

Under Rule 61G4-15.002, FAC, qualifying agents must maintain active, personal supervisory control over the plumbing operations of the firm. Permitting a business entity to use a contractor's license without exercising genuine management, jobsite inspection, and operational control is a major statutory violation known as "license lending" or "aiding and abetting unlicensed activity."

Continuing Education (CE) Requirements

To ensure licensed practitioners remain current with evolving codes, energy conservation criteria, and hurricane resiliency standards, the CILB mandates continuing education under FS 489.115 and Rule 61G4-18, FAC .

The 14-Hour Biennial Requirement

Certified and registered contractors must complete 14 hours of board-approved continuing education during each two-year (biennial) renewal cycle. The renewal cycle for Division II contractors ends on August 31 of even-numbered years .

The 14 hours must include the following mandatory specialized course hours:

1 hour Workplace Safety : OSHA regulations, excavation and trenching safety, personal protective equipment (PPE), hazard communication.

1 hour Business Practices : Accounting fundamentals, contract administration, lien law mechanics, financial recordkeeping.

1 hour Workers' Compensation : Florida statutory obligations under FS Chapter 440, coverage verification, exemption rules.

1 hour Laws and Rules : Florida Statutes Chapter 489, Chapter 455, board disciplinary procedures, statutory amendments.

1 hour Wind Mitigation : Techniques, roof and envelope penetration sealing, pipe flashings, structural uplift resistance.

1 hour Advanced Florida Building Code Module : Approved specialized course covering the most recent triennial edition and supplements of the Florida Building Code - Plumbing.

8 hours General / Technical Electives : Approved trade-specific courses, including backflow prevention, medical gas systems, water heater efficiency, and fuel gas piping.

Note

A contractor who fails to complete the mandatory 14 hours of continuing education prior to the August 31 biennial renewal deadline will have their license placed in Delinquent status. Practicing while delinquent is treated as unlicensed contracting.

Disciplinary Grounds & Unlicensed Contracting Penalties

The CILB possesses sweeping administrative enforcement powers under FS 455.227 and FS 489.129 to discipline licensed contractors who violate Florida law. In parallel, the state prosecutes unlicensed individuals under FS 489.127 .

Disciplinary Sanctions by the CILB

When a formal administrative complaint is sustained against a licensee, the CILB may impose one or more of the following sanctions:

Administrative Fines : Up to $10,000 per separate count or violation .

License Revocation : Complete and permanent termination of the right to practice contracting in Florida.

License Suspension : Temporary prohibition of practice for a specified duration or until restitution and fines are paid.

Probation : Continued practice subject to monitoring conditions, including quarterly financial reports, peer review, and additional continuing education courses.

Mandatory Restitution : Directing the contractor to reimburse damaged consumers for financial losses caused by substandard or abandoned work.

Re-examination : Requiring the licensee to retake and pass the Florida business & finance or plumbing trade examination.

Criminal Penalties for Unlicensed Contracting (FS 489.127)

Engaging in the business of plumbing contracting without an active, valid state certificate or registration is a criminal offense:

Standard First Offense : Classified as a first-degree misdemeanor , punishable by up to one year in county jail and a criminal fine of up to $1,000 , along with civil administrative penalties up to $10,000.

Subsequent Offenses : Any second or subsequent conviction is classified as a third-degree felony , punishable by up to five years in state prison and a fine of up to $5,000 .

State of Emergency Enhancement : Under FS 489.127(2)(b), committing unlicensed contracting during a declared state of emergency (issued by the Governor under FS 252.36, such as following a hurricane) automatically elevates a first offense from a misdemeanor to a third-degree felony . The Florida Legislature enacted this penalty enhancement to aggressively punish predatory, uncredentialed operators who exploit disaster victims.

Loading diagram... Florida CILB Licensure & Qualifying Agent Hierarchy