Study guide

10.1 Fuel Gas Fundamentals: Natural Gas vs LP Gas

Florida Journeyman Plumber Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Florida Plumbing Code Administration & Licensure

1.1 DBPR Licensing, CILB Regulations & Journeyman Qualifications 1.2 Permits, Inspections & Code Enforcement 1.3 Florida Construction Lien Law & Business Operations

2 Chapter 2: Sanitary Drainage Fundamentals & DFU Sizing

2.1 Gravity Drainage Principles & Florida DWV Materials 2.2 Drainage Fixture Units (DFU) & Load Values 2.3 Horizontal Branch & Vertical Stack Sizing 2.4 Drainage Fittings, Flow Direction & Change of Direction Rules

3 Chapter 3: Building Drains, Sewers & Special Drainage Systems

3.1 Building Drain & Building Sewer Sizing 3.2 Drainage Cleanouts: Sizing, Clearances & Locations 3.3 Sewage Ejectors, Sumps & Macerating Systems 3.4 Florida High Water Table, Slab Penetrations & Termite Protection

4 Chapter 4: Indirect Waste, Special Waste & Interceptors

4.1 Indirect Waste Systems: Air Gaps vs Air Breaks 4.2 Grease Interceptors: Hydromechanical & Gravity Interceptor Sizing 4.3 Sand, Oil & Specialized Interceptors

5 Chapter 5: Water Supply Systems & WSFU Pipe Sizing

5.1 Potable Water Piping Materials & Installation 5.2 Water Supply Fixture Units (WSFU) & Demand Estimations 5.3 Water Distribution Pipe Sizing Methods 5.4 Water Pressure Control, Boosting & PRVs

6 Chapter 6: Water Heaters, Cross-Connection Control & Reclaimed Water

6.1 Water Heaters & Safety Controls 6.2 Backflow Prevention & Cross-Connection Protection 6.3 Reclaimed Water Systems & Florida Dual-Plumbing Rules 6.4 System Testing, Disinfection & Commissioning

7 Chapter 7: DWV Venting Systems & Sizing

7.1 Principles of Venting & Trap Seal Integrity 7.2 Vent Sizing & Developed Length 7.3 Wet Venting & Horizontal Wet Venting 7.4 Circuit, Loop & Common Venting

8 Chapter 8: Specialized Venting & Air Admittance Valves

8.1 Island Fixture Vents & Foot Venting 8.2 Combination Waste and Vent Systems 8.3 Air Admittance Valves (AAVs) & Engineered Systems

9 Chapter 9: Isometric Drawing Interpretation & Drafting

9.1 Isometric Drawing Fundamentals and Plan Reading 9.2 Drafting Florida DWV Isometric Schematics 9.3 Local Exam Plan-Reading Practice and Self-Audit 9.4 Reading Plumbing Plans, Specifications & Schedules

10 Chapter 10: Fuel Gas Piping & Storm Drainage Systems

10.1 Fuel Gas Fundamentals: Natural Gas vs LP Gas 10.2 Gas Pipe Sizing & Demand Calculations 10.3 Gas Pipe Materials, Installation, Testing & Appliance Connections 10.4 Storm Drainage Sizing & Florida Rainfall Rates 10.5 Appliance Venting, Chimneys & Combustion Air

11 Chapter 11: Trade Mathematics, Accessibility & Jobsite Safety

11.1 Plumbing Math: Grade, Pitch & Elevation Calculations 11.2 Plumbing Math: 45-Degree & Rolling Offsets 11.3 Florida Accessibility Standards for Plumbing Fixtures 11.4 OSHA Construction Safety Standards for Plumbers 11.5 Plumbing Tools, Equipment & System Troubleshooting

12 Chapter 12: Medical Gas & Vacuum Piping Systems (NFPA 99)

12.1 Medical Gas Systems: Categories, Gases & Source Equipment 12.2 Medical Gas Piping Materials, Brazing & Nitrogen Purging 12.3 Station Outlets, Zone Valves, Alarms & Pipe Sizing 12.4 Medical-Surgical Vacuum, WAGD & System Verification

13 Chapter 13: Industrial, Process & Special-Waste Piping

13.1 Compressed Air & Industrial Gas Piping Systems 13.2 Industrial Vacuum Piping Systems 13.3 Process Piping & Steam Distribution Systems 13.4 Oil & Gasoline Storage and Distribution Systems 13.5 Industrial Water Drainage & Waste Pretreatment

14 Chapter 14: Site Utilities, Sewage Disposal & Water Mains

14.1 Onsite Sewage Treatment & Disposal: Septic Tanks & Drainfields 14.2 Sewage Lift Stations & Force Mains 14.3 Water Transmission Mains, Excavation & Heavy Equipment

15 Chapter 15: Pools, Wells, Irrigation, Solar & Fire Protection

15.1 Swimming Pool & Spa Piping Systems 15.2 Water Wells, Pumps & Irrigation Systems 15.3 Solar Water Heating Systems 15.4 Fire Protection Systems & Standpipes (NFPA 14)

10.1 Fuel Gas Fundamentals: Natural Gas vs LP Gas

Key Takeaways Explain This Topic AI

The Florida Building Code - Fuel Gas (FFGC), based on the International Fuel Gas Code (IFGC) with Florida-specific amendments, governs the design, installation, and inspection of fuel gas piping systems statewide.

Natural gas (predominantly methane, CH4) has a specific gravity of approximately 0.60 and rises to disperse in air, whereas liquefied petroleum gas (LP-gas / propane, C3H8) has a specific gravity of approximately 1.50 and settles into low areas, crawlspaces, and trenches, creating severe explosion hazards.

The nominal heating value of natural gas is 1,000 BTU per cubic foot compared to 2,500 BTU per cubic foot for propane, meaning natural gas requires 2.5 times the volumetric flow rate (CFH) to supply the identical thermal demand of an appliance.

Standard low-pressure natural gas systems deliver 7 inches water column (approx 1/4 psi) to building appliances, while LP-gas utilizes a two-stage regulator setup reducing container vapor pressure to 10 psi at the first stage and 11 inches water column at the second stage.

Both natural gas and propane must be odorized with an approved chemical agent such as ethyl mercaptan to ensure detectability at a concentration in air not exceeding one-fifth (20%) of the lower explosive limit.

Last updated: September 2026

Fuel Gas Fundamentals: Natural Gas vs LP Gas

Fuel gas infrastructure in the State of Florida is governed by strict statutory and administrative mandates designed to protect life, health, and property. Fuel gases are volatile hydrocarbon compounds that present profound combustion, asphyxiation, and detonation hazards if mishandled, improperly piped, or inadequately vented. For the journeyman plumber preparing for licensure and executing field installations, mastering the distinct physical properties, chemical characteristics, operating pressures, and volumetric flow math of both Natural Gas and Liquefied Petroleum Gas (LP-Gas / Propane) is essential.

Governing Code: Florida Building Code - Fuel Gas (FFGC)

In Florida, fuel gas piping systems are governed by the Florida Building Code - Fuel Gas (FFGC) . The FFGC is adopted triennially by the Florida Building Commission pursuant to Florida Statutes (FS) Chapter 553 .

The technical foundation of the FFGC is the International Fuel Gas Code (IFGC) , supplemented with Florida-specific amendments that address unique regional concerns—including intense lightning activity, high water tables, hurricane wind-load requirements, and exterior equipment anchoring. Plumbers must recognize that while the Florida Building Code - Plumbing (FPC) governs potable water, drainage, waste, and vent systems, the FFGC has exclusive jurisdiction over:

Fuel gas piping systems from the point of delivery to appliance shutoff valves.

Combustion air requirements for gas appliances.

Gas appliance venting, chimneys, and direct-vent systems.

Gas appliance installation, clearances, and commissioning.

The Point of Delivery

Under FFGC Chapter 2, the point of delivery defines the legal boundary where utility or fuel supplier responsibility ends and the licensed plumbing/gas contractor's installation begins:

For Natural Gas : The point of delivery is the outlet of the service meter assembly, or the outlet of the service regulator or service shutoff valve where no meter is provided.

For LP-Gas Systems : The point of delivery is the outlet of the final pressure regulator that reduces pressure to utilization pressure (the second-stage regulator at the building wall), or the service shutoff valve downstream of that regulator.

Natural Gas vs. Liquefied Petroleum Gas: Physical & Chemical Properties

A comprehensive comparison between Natural Gas and LP-Gas highlights the dramatic physical and chemical differences that dictate pipe sizing, burner design, and jobsite safety.

  • Engineering Property Natural Gas Liquefied Petroleum Gas (LP-Gas)
  • Primary Chemical Constituent Methane (CH₄, approx 90–95%) Propane (C₃H₈, approx 90–99%)
  • Physical State at Ambient Temp/Pressure Vapor / Gas Compressed Liquid in Tank; Vapor when Drawn
  • Specific Gravity (Air = 1.00) 0.60 (Nominal range: 0.55 to 0.65) 1.50 (Nominal range: 1.50 to 1.52)
  • Weight Relative to Atmospheric Air Lighter than air (Buoyant; rises) Heavier than air (Dense; sinks and pools)

Nominal Heating Value (Calorific Value) 1,000 BTU / cu ft (Actual: 1,000–1,050) 2,500 BTU / cu ft (Actual: ~2,516)

  • Standard Appliance Delivery Pressure 7 in. w.c. (0.25 psi; ~1/4 psi) 11 in. w.c. (0.40 psi; ~0.4 psi)
  • Alternative Medium-Pressure Delivery 2 psi (Hybrid manifold systems) 10 psi (First-stage line pressure)

Combustion Air Required per cu ft of Gas Approx 10 cu ft air (1 cu ft O₂) Approx 24 to 25 cu ft air (5 cu ft O₂)

  • Flammability Limits in Air (LEL - UEL) 5.0% to 15.0% by volume 2.15% to 9.60% by volume
  • Required Odorization Threshold Detectable at 1.0% in air (1/5 LEL) Detectable at 0.43% in air (1/5 LEL)
  • Specific Gravity & Practical Jobsite Hazards

Specific gravity represents the ratio of the density of a gas compared to the density of clean, dry ambient air (which has an assigned reference value of 1.00 at standard temperature and pressure).

Natural Gas (Methane CH₄: Specific Gravity ~0.60)

Because natural gas has a specific gravity of 0.60, it is 40% lighter than air . When a natural gas leak occurs in a building, the gas naturally rises toward the ceiling and diffuses rapidly into the surrounding air. In ventilated spaces or rooms with attic ventilation and high-wall registers, natural gas will dissipate upwards into the atmosphere, which significantly reduces the risk of long-term stratified explosive pockets forming at floor level.

LP-Gas (Propane C₃H₈: Specific Gravity ~1.50)

Propane has a specific gravity of 1.50, meaning it is 50% heavier than air . When propane leaks, it behaves like invisible water: it sinks to the lowest available plane, rolls down stairwells, migrates along slab contours, and collects in:

Plumbing slab trenches and under-slab blockouts.

Crawlspaces and unventilated basements.

Plumbing drainage cleanout pits, elevator sumps, and floor drains.

Caution

Because propane pools at floor level, an explosive fuel-air mixture can sit undisturbed in a low room or crawlspace for hours or days. The spark from a water heater igniter, an air conditioner contactor, or an appliance relay at floor level will trigger a devastating structure-level detonation. For this reason, the FFGC and NFPA 58 strictly prohibit the installation of LP-gas appliances, piping, or storage containers in pits, basements, or below-grade spaces where natural ventilation cannot purge heavy vapors.

Heating Values & Combustion Air Requirements

The heating value (heat of combustion) is the quantity of thermal energy produced by burning one cubic foot of gas, expressed in British Thermal Units per cubic foot (BTU/cu ft) .

Natural Gas : Nominal heating value of 1,000 BTU/cu ft . For code sizing calculations under FFGC Table 402.4, plumbers use 1,000 BTU/cu ft as the universal baseline.

Propane : Nominal heating value of 2,500 BTU/cu ft . Propane contains 2.5 times more thermal energy per unit volume than natural gas.

Burner Orifices and Field Conversions

Because propane provides 2.5 times the thermal energy per cubic foot of natural gas, an appliance burner designed for propane must consume only 40% of the volume of gas needed by a natural gas burner of the identical BTU rating. Consequently:

Propane burner orifices are significantly smaller than natural gas orifices.

Appliance field conversion : Installing a gas range, water heater, or furnace out of the box without converting the orifice and gas valve regulator from natural gas to propane will cause severe over-firing. Over-firing floods the combustion chamber with excess fuel, generating catastrophic levels of toxic carbon monoxide (CO), dense soot, burner flame rollout, and immediate fire hazards.

Air Requirements for Complete Combustion

Complete combustion requires sufficient oxygen to convert hydrocarbons into carbon dioxide (CO₂) and water vapor (H₂O):

Burning 1 cubic foot of natural gas requires 2 cubic feet of pure oxygen, which requires approximately 10 cubic feet of atmospheric air .

Burning 1 cubic foot of propane requires 5 cubic feet of pure oxygen, which requires approximately 24 to 25 cubic feet of atmospheric air .

Under FFGC Chapter 3, spaces containing propane appliances require substantial combustion air ducting or permanent louvers to prevent dangerous oxygen starvation.

Loading diagram... LP-Gas Two-Stage Regulation vs. Natural Gas Utility Delivery

System Delivery Pressures: Water Column & PSI

Gas pressures inside buildings are measured in two units:

Pounds per Square Inch (psi) : Used for high-pressure transmission mains, LP-gas tank pressures, and medium-pressure distribution.

Inches of Water Column (in. w.c.) : Used for low-pressure utilization systems. One psi equals 27.7 inches of water column . 1 psi = 27.7 in. w.c. \text{1 psi} = 27.7\text{ in. w.c.} 1 psi = 27.7 in. w.c. 7 in. w.c. = 7 27.7 ≈ 0.252 psi (approx 1/4 psi) \text{7 in. w.c.} = \frac{7}{27.7} \approx 0.252\text{ psi (approx 1/4 psi)} 7 in. w.c. = 27.7 7 ​ ≈ 0.252 psi (approx 1/4 psi) 11 in. w.c. = 11 27.7 ≈ 0.397 psi (approx 0.40 psi) \text{11 in. w.c.} = \frac{11}{27.7} \approx 0.397\text{ psi (approx 0.40 psi)} 11 in. w.c. = 27.7 11 ​ ≈ 0.397 psi (approx 0.40 psi)

Low-Pressure Natural Gas Delivery (7 in. w.c.)

The standard delivery pressure supplied by the gas utility regulator to a single-family home or light commercial structure is 7 inches water column (approx 1/4 psi) . The gas piping system is engineered to allow a maximum frictional pressure loss of 0.5 inches water column , ensuring that no less than 6.5 inches water column is delivered at the inlet of every appliance regulator under full simultaneous system demand.

Medium-Pressure Hybrid Natural Gas Systems (2 psi)

To overcome the large pipe diameters required by high-demand modern appliances (such as tankless water heaters and pool heaters), engineers frequently utilize 2-psi hybrid piping systems . Gas is distributed through smaller diameter piping (typically Corrugated Stainless Steel Tubing - CSST or black steel) at 2 psi (approx 55.4 in. w.c.) to intermediate manifolds. Line pressure regulators (MPRs) then step the pressure down to 7 to 11 in. w.c. at each appliance cluster.

LP-Gas Two-Stage Pressure Regulation

Propane container pressure fluctuates drastically with ambient Florida temperatures—from 50 psi in winter to over 200–250 psi on hot summer days. Standard gas appliance valves cannot handle pressures above 1/2 psi (14 in. w.c.). Therefore, the FFGC and NFPA 58 mandate a two-stage regulation system :

First-Stage Regulator : Installed directly at the tank vapor withdrawal valve. It reduces container vapor pressure down to a steady intermediate pressure of 10 psi .

Second-Stage Regulator : Installed outside the building on the exterior wall. It receives the 10 psi gas and reduces it to the standard appliance utilization pressure of 11 inches water column (approx 0.40 psi) .

Mandatory Odorization: Ethyl Mercaptan

In their natural, raw states, pure methane and pure propane are completely colorless, tasteless, and odorless. A massive, lethal leak could flood an occupied building without detection by building occupants.

Under FFGC Section 401.3 , all fuel gases distributed through piping systems must be effectively odorized by the addition of a chemical odorant. The industry standard odorant is ethyl mercaptan (ethanethiol, C₂H₅SH) , a volatile sulfur compound with a distinct, pungent smell resembling rotting cabbage or sulfur eggs.

The 20% LEL Legal Threshold

The FFGC mandates that fuel gas must be odorized so that the gas is detectable by a person with a normal sense of smell when the gas concentration in air reaches one-fifth (20%) of the lower explosive limit (LEL) :

Natural Gas : LEL is 5.0% in air. One-fifth of 5.0% is 1.0% . Therefore, natural gas must be clearly smelled before its concentration exceeds 1.0% in air.

Propane : LEL is 2.15% in air. One-fifth of 2.15% is 0.43% . Propane must be clearly smelled before its concentration exceeds 0.43% in air.

Warning

Odorant Fade in New Piping : Plumbers commissioning brand-new black steel gas lines must be alert to "odorant fade." Freshly threaded steel pipe contains internal surface rust, mill scale, and moisture that chemically absorb and neutralize ethyl mercaptan. During initial purging of new systems, gas may be flowing even if the mercaptan odor is temporarily subdued. Always use calibrated combustible gas detectors (sniffers) rather than relying exclusively on sense of smell.

Converting Appliance Input Ratings (BTU/hr) to Demand (CFH)

Gas piping sizing tables in FFGC Chapter 4 are not indexed by BTU/hr; they are indexed by volumetric flow capacity in Cubic Feet per Hour (CFH) . Therefore, the very first step in sizing any gas piping system is converting the appliance nameplate input rating (BTU/hr) into volumetric demand (CFH).

The Fundamental Demand Formula Demand (CFH) = Appliance Input Rating (BTU/hr) Heating Value of Gas (BTU/cu ft) \text{Demand (CFH)} = \frac{\text{Appliance Input Rating (BTU/hr)}}{\text{Heating Value of Gas (BTU/cu ft)}} Demand (CFH) = Heating Value of Gas (BTU/cu ft) Appliance Input Rating (BTU/hr) ​

For Natural Gas , use nominal 1,000 BTU/cu ft : Demand NG ( CFH ) = Appliance Input Rating (BTU/hr) 1 , 000 BTU/cu ft \text{Demand}_{\text{NG}} (\text{CFH}) = \frac{\text{Appliance Input Rating (BTU/hr)}}{1,000\text{ BTU/cu ft}} Demand NG ​ ( CFH ) = 1 , 000 BTU/cu ft Appliance Input Rating (BTU/hr) ​

For Propane (LP-Gas) , use nominal 2,500 BTU/cu ft : Demand LP ( CFH ) = Appliance Input Rating (BTU/hr) 2 , 500 BTU/cu ft \text{Demand}_{\text{LP}} (\text{CFH}) = \frac{\text{Appliance Input Rating (BTU/hr)}}{2,500\text{ BTU/cu ft}} Demand LP ​ ( CFH ) = 2 , 500 BTU/cu ft Appliance Input Rating (BTU/hr) ​

Worked Step-by-Step Demand Calculations

Let us calculate and compare the volumetric demand for common residential and light commercial plumbing fixtures across Florida:

Example 1: Whole-House Tankless Gas Water Heater (199,000 BTU/hr)

Natural Gas Demand : Demand NG = 199 , 000 BTU/hr 1 , 000 BTU/cu ft = 199 CFH \text{Demand}_{\text{NG}} = \frac{199,000\text{ BTU/hr}}{1,000\text{ BTU/cu ft}} = 199\text{ CFH} Demand NG ​ = 1 , 000 BTU/cu ft 199 , 000 BTU/hr ​ = 199 CFH

Propane (LP-Gas) Demand : Demand LP = 199 , 000 BTU/hr 2 , 500 BTU/cu ft = 79.6 CFH \text{Demand}_{\text{LP}} = \frac{199,000\text{ BTU/hr}}{2,500\text{ BTU/cu ft}} = 79.6\text{ CFH} Demand LP ​ = 2 , 500 BTU/cu ft 199 , 000 BTU/hr ​ = 79.6 CFH

Example 2: Residential Gas Cooktop / Range (65,000 BTU/hr)

Natural Gas Demand : Demand NG = 65 , 000 BTU/hr 1 , 000 BTU/cu ft = 65 CFH \text{Demand}_{\text{NG}} = \frac{65,000\text{ BTU/hr}}{1,000\text{ BTU/cu ft}} = 65\text{ CFH} Demand NG ​ = 1 , 000 BTU/cu ft 65 , 000 BTU/hr ​ = 65 CFH

Propane (LP-Gas) Demand : Demand LP = 65 , 000 BTU/hr 2 , 500 BTU/cu ft = 26 CFH \text{Demand}_{\text{LP}} = \frac{65,000\text{ BTU/hr}}{2,500\text{ BTU/cu ft}} = 26\text{ CFH} Demand LP ​ = 2 , 500 BTU/cu ft 65 , 000 BTU/hr ​ = 26 CFH

Example 3: High-Efficiency Central Furnace (100,000 BTU/hr)

Natural Gas Demand : Demand NG = 100 , 000 BTU/hr 1 , 000 BTU/cu ft = 100 CFH \text{Demand}_{\text{NG}} = \frac{100,000\text{ BTU/hr}}{1,000\text{ BTU/cu ft}} = 100\text{ CFH} Demand NG ​ = 1 , 000 BTU/cu ft 100 , 000 BTU/hr ​ = 100 CFH

Propane (LP-Gas) Demand : Demand LP = 100 , 000 BTU/hr 2 , 500 BTU/cu ft = 40 CFH \text{Demand}_{\text{LP}} = \frac{100,000\text{ BTU/hr}}{2,500\text{ BTU/cu ft}} = 40\text{ CFH} Demand LP ​ = 2 , 500 BTU/cu ft 100 , 000 BTU/hr ​ = 40 CFH

Example 4: Florida Outdoor Commercial Pool / Spa Heater (400,000 BTU/hr)

Natural Gas Demand : Demand NG = 400 , 000 BTU/hr 1 , 000 BTU/cu ft = 400 CFH \text{Demand}_{\text{NG}} = \frac{400,000\text{ BTU/hr}}{1,000\text{ BTU/cu ft}} = 400\text{ CFH} Demand NG ​ = 1 , 000 BTU/cu ft 400 , 000 BTU/hr ​ = 400 CFH

Propane (LP-Gas) Demand : Demand LP = 400 , 000 BTU/hr 2 , 500 BTU/cu ft = 160 CFH \text{Demand}_{\text{LP}} = \frac{400,000\text{ BTU/hr}}{2,500\text{ BTU/cu ft}} = 160\text{ CFH} Demand LP ​ = 2 , 500 BTU/cu ft 400 , 000 BTU/hr ​ = 160 CFH

Comprehensive Appliance Demand Reference Table

  • Plumbing / Heating Appliance Nameplate Input (BTU/hr) Natural Gas Demand (CFH) LP-Gas (Propane) Demand (CFH)
  • Standard Storage Water Heater (40 Gal) 40,000 40 CFH 16 CFH
  • Standard Storage Water Heater (50 Gal) 50,000 50 CFH 20 CFH
  • Tankless Water Heater (Whole-House) 199,000 199 CFH 79.6 CFH
  • Commercial Tankless Water Heater 250,000 250 CFH 100 CFH
  • Residential Cooktop / Range 65,000 65 CFH 26 CFH
  • Commercial Restaurant Range 150,000 150 CFH 60 CFH
  • Residential Clothes Dryer 35,000 35 CFH 14 CFH
  • Central Warm-Air Furnace 80,000 80 CFH 32 CFH
  • Large Residential Furnace 120,000 120 CFH 48 CFH
  • Outdoor Gas Barbecue Grill 50,000 50 CFH 20 CFH
  • Outdoor Fire Pit / Torch Feature 60,000 60 CFH 24 CFH
  • Residential Pool / Spa Heater 250,000 250 CFH 100 CFH
  • High-Capacity Pool Heater 400,000 400 CFH 160 CFH
  • Key Takeaway for Pipe Sizing

Notice that for every appliance listed, the Natural Gas volumetric demand in CFH is exactly 2.5 times higher than the Propane demand . Because pipe diameter is determined by volumetric displacement, a natural gas piping system requires significantly larger pipe diameters than a propane system supplying the exact same appliances.