Study guide

4.2 Grease Interceptors: Hydromechanical & Gravity Interceptor Sizing

Florida Journeyman Plumber Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Florida Plumbing Code Administration & Licensure

1.1 DBPR Licensing, CILB Regulations & Journeyman Qualifications 1.2 Permits, Inspections & Code Enforcement 1.3 Florida Construction Lien Law & Business Operations

2 Chapter 2: Sanitary Drainage Fundamentals & DFU Sizing

2.1 Gravity Drainage Principles & Florida DWV Materials 2.2 Drainage Fixture Units (DFU) & Load Values 2.3 Horizontal Branch & Vertical Stack Sizing 2.4 Drainage Fittings, Flow Direction & Change of Direction Rules

3 Chapter 3: Building Drains, Sewers & Special Drainage Systems

3.1 Building Drain & Building Sewer Sizing 3.2 Drainage Cleanouts: Sizing, Clearances & Locations 3.3 Sewage Ejectors, Sumps & Macerating Systems 3.4 Florida High Water Table, Slab Penetrations & Termite Protection

4 Chapter 4: Indirect Waste, Special Waste & Interceptors

4.1 Indirect Waste Systems: Air Gaps vs Air Breaks 4.2 Grease Interceptors: Hydromechanical & Gravity Interceptor Sizing 4.3 Sand, Oil & Specialized Interceptors

5 Chapter 5: Water Supply Systems & WSFU Pipe Sizing

5.1 Potable Water Piping Materials & Installation 5.2 Water Supply Fixture Units (WSFU) & Demand Estimations 5.3 Water Distribution Pipe Sizing Methods 5.4 Water Pressure Control, Boosting & PRVs

6 Chapter 6: Water Heaters, Cross-Connection Control & Reclaimed Water

6.1 Water Heaters & Safety Controls 6.2 Backflow Prevention & Cross-Connection Protection 6.3 Reclaimed Water Systems & Florida Dual-Plumbing Rules 6.4 System Testing, Disinfection & Commissioning

7 Chapter 7: DWV Venting Systems & Sizing

7.1 Principles of Venting & Trap Seal Integrity 7.2 Vent Sizing & Developed Length 7.3 Wet Venting & Horizontal Wet Venting 7.4 Circuit, Loop & Common Venting

8 Chapter 8: Specialized Venting & Air Admittance Valves

8.1 Island Fixture Vents & Foot Venting 8.2 Combination Waste and Vent Systems 8.3 Air Admittance Valves (AAVs) & Engineered Systems

9 Chapter 9: Isometric Drawing Interpretation & Drafting

9.1 Isometric Drawing Fundamentals and Plan Reading 9.2 Drafting Florida DWV Isometric Schematics 9.3 Local Exam Plan-Reading Practice and Self-Audit 9.4 Reading Plumbing Plans, Specifications & Schedules

10 Chapter 10: Fuel Gas Piping & Storm Drainage Systems

10.1 Fuel Gas Fundamentals: Natural Gas vs LP Gas 10.2 Gas Pipe Sizing & Demand Calculations 10.3 Gas Pipe Materials, Installation, Testing & Appliance Connections 10.4 Storm Drainage Sizing & Florida Rainfall Rates 10.5 Appliance Venting, Chimneys & Combustion Air

11 Chapter 11: Trade Mathematics, Accessibility & Jobsite Safety

11.1 Plumbing Math: Grade, Pitch & Elevation Calculations 11.2 Plumbing Math: 45-Degree & Rolling Offsets 11.3 Florida Accessibility Standards for Plumbing Fixtures 11.4 OSHA Construction Safety Standards for Plumbers 11.5 Plumbing Tools, Equipment & System Troubleshooting

12 Chapter 12: Medical Gas & Vacuum Piping Systems (NFPA 99)

12.1 Medical Gas Systems: Categories, Gases & Source Equipment 12.2 Medical Gas Piping Materials, Brazing & Nitrogen Purging 12.3 Station Outlets, Zone Valves, Alarms & Pipe Sizing 12.4 Medical-Surgical Vacuum, WAGD & System Verification

13 Chapter 13: Industrial, Process & Special-Waste Piping

13.1 Compressed Air & Industrial Gas Piping Systems 13.2 Industrial Vacuum Piping Systems 13.3 Process Piping & Steam Distribution Systems 13.4 Oil & Gasoline Storage and Distribution Systems 13.5 Industrial Water Drainage & Waste Pretreatment

14 Chapter 14: Site Utilities, Sewage Disposal & Water Mains

14.1 Onsite Sewage Treatment & Disposal: Septic Tanks & Drainfields 14.2 Sewage Lift Stations & Force Mains 14.3 Water Transmission Mains, Excavation & Heavy Equipment

15 Chapter 15: Pools, Wells, Irrigation, Solar & Fire Protection

15.1 Swimming Pool & Spa Piping Systems 15.2 Water Wells, Pumps & Irrigation Systems 15.3 Solar Water Heating Systems 15.4 Fire Protection Systems & Standpipes (NFPA 14)

4.2 Grease Interceptors: Hydromechanical & Gravity Interceptor Sizing

Key Takeaways Explain This Topic AI

Fats, Oils, and Grease (FOG) entering sanitary sewers undergo saponification with calcium and alkaline minerals to create rock-hard 'fatbergs,' making interceptor installation mandatory under FPC Section 1003 for all commercial food establishments.

Hydromechanical Grease Interceptors (HGIs) comply with ASME A112.14.3 / PDI G101 standards, use flow control devices with air intake to separate grease at 90%+ efficiency, and possess a grease retention capacity in pounds equal to exactly twice their flow rating in GPM.

Gravity Grease Interceptors (GGIs) comply with ASME A112.14.4 / IAPMO Z1001, featuring large outdoor inground vaults (typically 750 to 2,000+ gallons) designed around a minimum 30-minute hydraulic retention time.

Point-of-use HGI sizing converts total sink compartment volume (cubic inches divided by 231) into liquid gallons, applies a 75% operational fill factor, and divides by a 1- or 2-minute drain duration to establish the required GPM flow rating.

Florida environmental regulations and municipal FOG ordinances enforce the 25% Rule, which mandates complete pump-out and cleaning when accumulated floating grease and settled bottom solids exceed 25% of the interceptor's total liquid capacity.

Last updated: September 2026

4.2 Grease Interceptors: Hydromechanical & Gravity Interceptor Sizing

Discharge containing Fats, Oils, and Grease ( FOG ) represents the single greatest mechanical threat to public sanitary sewer systems. When commercial kitchens discharge hot greasy dishwater into drainage pipes, the grease initially remains liquefied. However, as the waste cools below 100 ∘ F 100^\circ\text{F} 10 0 ∘ F ( 37.8 ∘ C 37.8^\circ\text{C} 37. 8 ∘ C ), animal fats and vegetable oils congeal and solidify onto pipe inverts.

In municipal sewers, congealed grease undergoes a chemical reaction known as saponification : free fatty acids react with calcium and alkaline minerals present in domestic wastewater and concrete sewer pipes, forming insoluble, rock-hard metallic soap deposits known as fatbergs . These fatbergs choke municipal sewer mains, causing catastrophic Sanitary Sewer Overflows (SSOs) that discharge millions of gallons of raw sewage into Florida's fragile waterways and coastal aquifers.

To prevent this, Florida Plumbing Code (FPC) Section 1003.3 strictly mandates that all commercial food service establishments (restaurants, cafeterias, bakeries, butcher shops, institutional kitchens) install approved grease interceptors.

1. HGI vs. GGI: Technical Comparison

The Florida Plumbing Code recognizes two fundamentally distinct classes of grease interceptors:

  • Hydromechanical Grease Interceptors (HGI) (ASME A112.14.3 / PDI G101 / CSA B481.1)
  • Gravity Grease Interceptors (GGI) (ASME A112.14.4 / IAPMO Z1001)
  • Technical Attribute Hydromechanical Grease Interceptor (HGI) Gravity Grease Interceptor (GGI)
  • Governing Standard ASME A112.14.3 / PDI G101 ASME A112.14.4 / IAPMO Z1001
  • Physical Location Indoors, point-of-use under sinks or recessed in floor Outdoors, underground inground vault
  • Liquid Capacity Compact (typically 15 to 100 gallons) Massive (typically 750 to 2,000+ gallons)

Hydraulic Retention Time Minutes (rapid mechanical separation) Minimum 30 minutes (gravitational quiescent separation)

Separation Mechanism Hydrodynamic flow control, baffling, air entrainment Specific gravity flotation and quiescent sedimentation

Flow Control Device Mandatory external vented flow control Not used (gravity flow through oversized chambers)

Grease Retention Rating Pounds of Grease = 2 × 2 \times 2 × Flow Rate in GPM Rated by liquid volume in gallons and sludge storage depth

Construction Materials Engineered polymers, stainless steel, coated cast iron Precast concrete, fiberglass, high-density polyethylene

Pumping Maintenance Manual skimming or weekly/monthly pump-out Vacuum tanker truck pumping every 30 to 90 days

Loading diagram... Hydromechanical Grease Interceptor (HGI) Internal Flow Dynamics

2. Hydromechanical Grease Interceptors (HGI) Engineering

Hydromechanical interceptors rely on hydrodynamics and physics rather than sheer holding volume. Under PDI G101 and ASME A112.14.3 , HGIs achieve grease separation efficiencies exceeding 90% through three coordinated features:

The Vented Flow Control Device

The flow control fitting is an engineered orifice installed on the inlet piping immediately before the interceptor.

It regulates incoming wastewater so the velocity never exceeds the interceptor's certified flow rating in gallons per minute (GPM).

The Air Entrainment Port : The fitting features an atmospheric air intake port that pulls room air into the moving stream (the Venturi effect). This entrains millions of microscopic air bubbles into the oily wastewater.

The Floatation Principle : Micro-bubbles adhere to microscopic emulsified grease globules, dramatically lowering their effective specific gravity and accelerating their flotation rise velocity toward the surface storage zone.

Caution

The Flow Control Tampering Violation : Kitchen operators frequently remove the flow control fitting or drill out the orifice because "the sink drains too slowly." Removing the flow control destroys the interceptor's hydrodynamic performance: turbulent unmetered water blows straight through the baffles, scouring out previously captured grease and blasting it into the municipal sewer line. Installing an HGI without its approved flow control device is an immediate code failure.

The 2:1 Grease Capacity Rating (PDI G101 Standard)

Under the Plumbing and Drainage Institute (PDI) G101 standard, every hydromechanical interceptor has a mandatory relationship between its flow rate and its grease storage capacity: Grease Retention Capacity (lbs) = 2 × Certified Flow Rate (GPM) \text{Grease Retention Capacity (lbs)} = 2 \times \text{Certified Flow Rate (GPM)} Grease Retention Capacity (lbs) = 2 × Certified Flow Rate (GPM)

A 20 GPM interceptor must retain at least 40 pounds of grease.

A 35 GPM interceptor must retain at least 70 pounds of grease.

A 50 GPM interceptor must retain at least 100 pounds of grease.

A 100 GPM interceptor must retain at least 200 pounds of grease.

3. Gravity Grease Interceptors (GGI) Engineering

Outdoor Gravity Grease Interceptors are massive multi-compartment vessels (ranging from 750 gallons to 2,000+ gallons ) buried in exterior vehicular drives or service alleys.

ASME A112.14.4 / IAPMO Z1001 : GGIs achieve separation purely by quiescent (still-water) gravitational settling.

30-Minute Retention Time : GGIs are engineered so that wastewater remains inside the tank for a minimum hydraulic retention time (HRT) of 30 minutes during peak flow periods.

Internal Baffling & Sanitary Tees : Incoming waste enters through an extended sanitary tee that directs flow downward. The tank is divided into two or three chambers by internal concrete baffles. Submerged flow-through tees or slots draw water from the neutral middle layer (between the top 25% grease cap and the bottom 25% sludge layer) to prevent short-circuiting.

Florida Buoyancy & High Water Table Concern : In Florida's high water tables, an empty 1,500-gallon concrete GGI acts like a boat hull, displacing up to 12,500 pounds of water. GGIs must be engineered with reinforced concrete anti-flotation ballast pads, extended bottom flanges, or helical tie-down anchors to prevent hydrostatic uplift from popping the tank out of the ground.

  • 4. Step-by-Step Sizing Calculations
  • Method 1: Point-of-Use HGI Sizing Based on Fixture Volume (PDI G101)

To size an HGI serving a multi-compartment commercial sink, follow the standardized five-step engineering procedure: Volume (Cubic Inches) = Length × Width × Depth × Compartments \text{Volume (Cubic Inches)} = \text{Length} \times \text{Width} \times \text{Depth} \times \text{Compartments} Volume (Cubic Inches) = Length × Width × Depth × Compartments Capacity (Gallons) = Volume in Cubic Inches 231 \text{Capacity (Gallons)} = \frac{\text{Volume in Cubic Inches}}{231} Capacity (Gallons) = 231 Volume in Cubic Inches ​ Actual Liquid Discharge = Capacity (Gallons) × 0.75 ( 75% Operational Fill Factor ) \text{Actual Liquid Discharge} = \text{Capacity (Gallons)} \times 0.75 \quad (\text{75\% Operational Fill Factor}) Actual Liquid Discharge = Capacity (Gallons) × 0.75 ( 75% Operational Fill Factor ) Flow Rate (GPM) = Actual Liquid Discharge Drain Period (1 or 2 Minutes) \text{Flow Rate (GPM)} = \frac{\text{Actual Liquid Discharge}}{\text{Drain Period (1 or 2 Minutes)}} Flow Rate (GPM) = Drain Period (1 or 2 Minutes) Actual Liquid Discharge ​

Worked Example: 3-Compartment Commercial Pot Sink

A commercial kitchen in Orlando features a 3-compartment pot washing sink with each compartment measuring 24 inches long × \times × 24 inches wide × \times × 14 inches deep . Determine the required HGI flow rating for both a 1-minute and a 2-minute drain period.

Step 1: Calculate Total Cubic Volume : Single Compartment = 24 × 24 × 14 = 8 , 064 in 3 \text{Single Compartment} = 24 \times 24 \times 14 = 8,064 \text{ in}^3 Single Compartment = 24 × 24 × 14 = 8 , 064 in 3 Total Sink Volume = 8 , 064 × 3 = 24 , 192 in 3 \text{Total Sink Volume} = 8,064 \times 3 = 24,192 \text{ in}^3 Total Sink Volume = 8 , 064 × 3 = 24 , 192 in 3

Step 2: Convert to Total Gallons ( 231 cubic inches per gallon 231 \text{ cubic inches per gallon} 231 cubic inches per gallon ): Total Gallons = 24 , 192 231 = 104.73 gallons \text{Total Gallons} = \frac{24,192}{231} = 104.73 \text{ gallons} Total Gallons = 231 24 , 192 ​ = 104.73 gallons

Step 3: Apply the 75% Fill Factor (dishes and pots displace water; sinks are rarely filled to the rim): Actual Discharge Volume = 104.73 × 0.75 = 78.55 gallons \text{Actual Discharge Volume} = 104.73 \times 0.75 = 78.55 \text{ gallons} Actual Discharge Volume = 104.73 × 0.75 = 78.55 gallons

Step 4: Calculate Required Flow Rate (GPM) :

For a 1-Minute Drain Period : Flow Rate = 78.55 gal 1 min = 78.55 GPM \text{Flow Rate} = \frac{78.55 \text{ gal}}{1 \text{ min}} = 78.55 \text{ GPM} Flow Rate = 1 min 78.55 gal ​ = 78.55 GPM Selection : Next larger standard certified HGI size = 100 GPM (with 200 lbs grease capacity).

For a 2-Minute Drain Period (industry standard practice): Flow Rate = 78.55 gal 2 min = 39.27 GPM \text{Flow Rate} = \frac{78.55 \text{ gal}}{2 \text{ min}} = 39.27 \text{ GPM} Flow Rate = 2 min 78.55 gal ​ = 39.27 GPM Selection : Next larger standard certified HGI size = 50 GPM (with 100 lbs grease capacity).

Method 2: Gravity Grease Interceptor (GGI) Sizing Formula

Florida municipalities (such as Miami-Dade, Orange County, and Jacksonville JEA) utilize the standard restaurant sizing formula based on seating capacity, meal duration, and storage factors: V = S × M × G L × ( H 2 ) × L F V = S \times M \times GL \times \left(\frac{H}{2}\right) \times LF V = S × M × G L × ( 2 H ​ ) × L F

Where:

V V V = Liquid volume of interceptor in gallons.

S S S = Number of seats in dining area.

M M M = Meals per seat per hour (typically 1.0 to 1.5 for full-service restaurants).

G L GL G L = Gallons of wastewater per meal (typically 5 gallons with full commercial kitchen).

H H H = Hours of restaurant operation per day.

L F LF L F = Loading Factor (1.25 for interstate/freeway locations; 1.0 for standard commercial; 0.75 for non-grease menus).

Worked Example: 80-Seat Florida Restaurant

An 80-seat full-service restaurant operates 12 hours per day with M = 1.0 M = 1.0 M = 1.0 , G L = 5.0 GL = 5.0 G L = 5.0 , and L F = 1.0 LF = 1.0 L F = 1.0 : V = 80 × 1.0 × 5.0 × ( 12 2 ) × 1.0 V = 80 \times 1.0 \times 5.0 \times \left(\frac{12}{2}\right) \times 1.0 V = 80 × 1.0 × 5.0 × ( 2 12 ​ ) × 1.0 V = 80 × 5.0 × 6 × 1.0 = 2 , 400 gallons V = 80 \times 5.0 \times 6 \times 1.0 = 2,400 \text{ gallons} V = 80 × 5.0 × 6 × 1.0 = 2 , 400 gallons

Selection : A standard 2,500-gallon two-compartment precast concrete GGI (or two 1,250-gallon tanks in series) is required.

5. Florida FOG Ordinances & The 25% Rule

Florida's municipal wastewater utilities enforce strict Fats, Oils, and Grease (FOG) Management Ordinances under regulatory authority from the Florida Department of Environmental Protection (FDEP).

The Mandatory 25% Rule

Every commercial kitchen grease interceptor in Florida is legally subject to the 25% Rule :

An interceptor must be completely pumped out and cleaned whenever the combined thickness of the floating grease layer (top) plus the settled sludge solids (bottom) exceeds 25% of the total liquid operating depth of the interceptor.

The Sludge Judge Measurement : Environmental compliance officers insert a clear graduated sampling tube (a "Sludge Judge") to the bottom of the interceptor to measure the exact vertical inches of the grease cap, clear water zone, and bottom sediment.

The Failure Point : Once accumulated FOG and solids reach 25%, the effective hydraulic retention time is cut in half. Water velocity increases, and the interceptor begins scouring and flushing trapped grease straight into the city sewer main.

Effluent Sampling Manholes

All outdoor gravity grease interceptors must feature a dedicated sampling manhole (or sampling port) installed on the effluent discharge line downstream of the interceptor before connecting to the public sewer.

Municipal inspectors use this port to take grab samples. The legal discharge limit in Florida is typically 100 mg/L (or 200 mg/L in some utilities) of FOG. Discharges exceeding the limit trigger heavy daily fines and mandatory mandated pump-out contracts.

6. Common Exam Traps & Practical Field Violations

Connecting Sanitary Fixtures to Grease Piping : Never connect toilets, urinals, or bathroom lavatories into grease waste lines. FPC Section 1003.3.2 strictly prohibits sanitary sewage from entering grease interceptors. Human fecal bacteria destroy grease separation and turn the interceptor into a hazardous biohazard septic pit.

Commercial Dishwasher Discharge into HGIs : In many Florida jurisdictions, discharging a high-temperature commercial dishwasher ( 180 ∘ F 180^\circ\text{F} 18 0 ∘ F sanitizing rinse) directly into an indoor point-of-use HGI is prohibited. The extreme hot water emulsifies grease into microscopic droplets that bypass the HGI baffles and re-solidify in the municipal main downstream.

Omitting the Interceptor Vent : An HGI or GGI must be vented on both its inlet and outlet drainage lines. Failing to vent the outlet causes siphonage of the interceptor's internal liquid seal, allowing toxic sewer gases to escape through kitchen sink drains.

Food Waste Disposers (Garbage Disposals) : Commercial food waste disposers must never discharge directly into an HGI unless an approved solids interceptor is installed ahead of the unit. Ground food waste rapidly fills the interceptor with heavy solids, violating the 25% rule within days.