Study guide

13.1 Compressed Air & Industrial Gas Piping Systems

Florida Journeyman Plumber Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Florida Plumbing Code Administration & Licensure

1.1 DBPR Licensing, CILB Regulations & Journeyman Qualifications 1.2 Permits, Inspections & Code Enforcement 1.3 Florida Construction Lien Law & Business Operations

2 Chapter 2: Sanitary Drainage Fundamentals & DFU Sizing

2.1 Gravity Drainage Principles & Florida DWV Materials 2.2 Drainage Fixture Units (DFU) & Load Values 2.3 Horizontal Branch & Vertical Stack Sizing 2.4 Drainage Fittings, Flow Direction & Change of Direction Rules

3 Chapter 3: Building Drains, Sewers & Special Drainage Systems

3.1 Building Drain & Building Sewer Sizing 3.2 Drainage Cleanouts: Sizing, Clearances & Locations 3.3 Sewage Ejectors, Sumps & Macerating Systems 3.4 Florida High Water Table, Slab Penetrations & Termite Protection

4 Chapter 4: Indirect Waste, Special Waste & Interceptors

4.1 Indirect Waste Systems: Air Gaps vs Air Breaks 4.2 Grease Interceptors: Hydromechanical & Gravity Interceptor Sizing 4.3 Sand, Oil & Specialized Interceptors

5 Chapter 5: Water Supply Systems & WSFU Pipe Sizing

5.1 Potable Water Piping Materials & Installation 5.2 Water Supply Fixture Units (WSFU) & Demand Estimations 5.3 Water Distribution Pipe Sizing Methods 5.4 Water Pressure Control, Boosting & PRVs

6 Chapter 6: Water Heaters, Cross-Connection Control & Reclaimed Water

6.1 Water Heaters & Safety Controls 6.2 Backflow Prevention & Cross-Connection Protection 6.3 Reclaimed Water Systems & Florida Dual-Plumbing Rules 6.4 System Testing, Disinfection & Commissioning

7 Chapter 7: DWV Venting Systems & Sizing

7.1 Principles of Venting & Trap Seal Integrity 7.2 Vent Sizing & Developed Length 7.3 Wet Venting & Horizontal Wet Venting 7.4 Circuit, Loop & Common Venting

8 Chapter 8: Specialized Venting & Air Admittance Valves

8.1 Island Fixture Vents & Foot Venting 8.2 Combination Waste and Vent Systems 8.3 Air Admittance Valves (AAVs) & Engineered Systems

9 Chapter 9: Isometric Drawing Interpretation & Drafting

9.1 Isometric Drawing Fundamentals and Plan Reading 9.2 Drafting Florida DWV Isometric Schematics 9.3 Local Exam Plan-Reading Practice and Self-Audit 9.4 Reading Plumbing Plans, Specifications & Schedules

10 Chapter 10: Fuel Gas Piping & Storm Drainage Systems

10.1 Fuel Gas Fundamentals: Natural Gas vs LP Gas 10.2 Gas Pipe Sizing & Demand Calculations 10.3 Gas Pipe Materials, Installation, Testing & Appliance Connections 10.4 Storm Drainage Sizing & Florida Rainfall Rates 10.5 Appliance Venting, Chimneys & Combustion Air

11 Chapter 11: Trade Mathematics, Accessibility & Jobsite Safety

11.1 Plumbing Math: Grade, Pitch & Elevation Calculations 11.2 Plumbing Math: 45-Degree & Rolling Offsets 11.3 Florida Accessibility Standards for Plumbing Fixtures 11.4 OSHA Construction Safety Standards for Plumbers 11.5 Plumbing Tools, Equipment & System Troubleshooting

12 Chapter 12: Medical Gas & Vacuum Piping Systems (NFPA 99)

12.1 Medical Gas Systems: Categories, Gases & Source Equipment 12.2 Medical Gas Piping Materials, Brazing & Nitrogen Purging 12.3 Station Outlets, Zone Valves, Alarms & Pipe Sizing 12.4 Medical-Surgical Vacuum, WAGD & System Verification

13 Chapter 13: Industrial, Process & Special-Waste Piping

13.1 Compressed Air & Industrial Gas Piping Systems 13.2 Industrial Vacuum Piping Systems 13.3 Process Piping & Steam Distribution Systems 13.4 Oil & Gasoline Storage and Distribution Systems 13.5 Industrial Water Drainage & Waste Pretreatment

14 Chapter 14: Site Utilities, Sewage Disposal & Water Mains

14.1 Onsite Sewage Treatment & Disposal: Septic Tanks & Drainfields 14.2 Sewage Lift Stations & Force Mains 14.3 Water Transmission Mains, Excavation & Heavy Equipment

15 Chapter 15: Pools, Wells, Irrigation, Solar & Fire Protection

15.1 Swimming Pool & Spa Piping Systems 15.2 Water Wells, Pumps & Irrigation Systems 15.3 Solar Water Heating Systems 15.4 Fire Protection Systems & Standpipes (NFPA 14)

13.1 Compressed Air & Industrial Gas Piping Systems

Key Takeaways Explain This Topic AI

Compressed-air design requires service-rated materials, moisture control, pressure-loss evaluation and safe tool connections.

OSHA 1926.302(b)(4) generally requires cleaning air below 30 psi plus effective chip guarding and PPE; its pressure exception covers concrete forms, mill scale and similar cleaning.

OSHA 29 CFR 1926.302(b)(7) requires all hoses exceeding 1/2-inch inside diameter to have a safety device at the source of supply or branch line to reduce pressure in case of hose failure.

Ordinary liquid-rated PVC/CPVC is not an acceptable substitute for a piping system approved for the actual compressed-gas service and its required protections.

In the supplied wet-header design, the header slopes 1 inch in 10 feet toward drains and tool takeoffs rise from the top to reduce liquid carryover; actual geometry follows the approved design.

Last updated: October 2026

Compressed Air & Industrial Gas Piping Systems

Compressed-air and industrial-gas distribution connect material selection, pressure loss, moisture control and worker safety. This section provides supplemental technical practice; local journeyman exam coverage is determined by the approved local outline, not by a borrowed plumbing-contractor percentage.

Compressed air is often called the fourth utility. Its applications include light industrial, automotive, dental, agricultural and food-processing jobs; the specific service and licensing scope must be established for the project.

1. The Compressed Air Train

Air moves through a predictable sequence of components, and each one exists to remove something that would otherwise damage a tool:

Component Function What Goes Wrong Without It

Compressor (reciprocating, rotary screw, or scroll) Raises atmospheric air to line pressure, typically 100 to 125 psig —

Aftercooler Drops discharge temperature, condensing the bulk of the moisture Hot saturated air carries water all the way to the tools

Receiver tank Stores volume, dampens pulsation, lets condensate settle Compressor short-cycles; pressure collapses on every surge demand

Filter (particulate then coalescing) Removes rust, pipe scale and oil aerosol Oil-fouled tools and contaminated paint work

Dryer (refrigerated or desiccant) Lowers the pressure dew point below the coldest pipe temperature Liquid water in the distribution main

Regulator at each drop Sets tool pressure below main pressure Tools run over their rated pressure and wear out

Drip legs and automatic drains Collect and discharge condensate Slugs of water reach the tool and freeze the exhaust port

Select by pressure dew point and actual exposure. A refrigerated dryer can produce a pressure dew point in the roughly 35–40°F range, depending on the product and conditions. Suitability depends on the lowest temperature the piping and equipment will encounter, including cold rooms or outdoor exposure. An attic or outdoor location alone does not prove that a desiccant dryer is required. Choose a dryer whose rated performance meets the specified pressure dew point below the expected minimum temperature, with the design margin required for the application.

2. Materials Must Be Approved for the Actual Service

Compressed gas piping stores energy. Both liquid and gas failures can injure workers; compressed gas expansion can release substantial stored energy and propel fragments.

Common candidate materials, subject to service ratings, joining method and applicable approval:

Schedule 40 black steel (ASTM A53), threaded or welded — the traditional shop standard. Interior rusts over time and sheds scale, which is why filters sit downstream.

Type L or Type K copper tube , brazed — clean, smooth-bore, no scale, and the usual choice where air quality matters.

Stainless steel — food, pharmaceutical and marine environments.

Listed modular aluminum systems — engineered push-to-connect aluminum systems specifically listed for compressed air.

Galvanized steel requires service approval and air-quality evaluation; coating debris is one potential contamination concern.

Warning

Do not select ordinary PVC or CPVC water pipe for compressed-air service from its liquid pressure rating. Compressed gas stores substantial energy, and brittle failure can project fragments. Use a piping system specifically approved by its manufacturer for the actual gas, pressure, temperature and installation, with the required code and workplace protections.

Industrial gases other than air — nitrogen, argon, carbon dioxide, oxygen and fuel gas mixtures for welding — follow the same discipline with additions: oxygen service piping must be cleaned for oxygen service and kept free of oil and grease , and nonmedical oxygen systems in Florida are governed by NFPA 55 and NFPA 51 through FPC Section 1203.1 , not by NFPA 99.

3. Header and Drop Geometry

The layout rules exist to keep condensate out of tools:

The following is a supplied wet-header design example , not a universal compressed-air layout or code slope. The approved equipment arrangement and process determine actual components and geometry.

Pitch the header. This drawing specifies 1 inch in 10 feet toward its designated condensate collection points.

Drip legs at every low point and at the end of every main. A drip leg is a full-size vertical extension of the main running down past the branch takeoff, capped with a valve or automatic drain.

For this wet-header design, take tool branches off the top. The classic gooseneck takeoff rises from the crown of the header, turns over, and drops to the tool station. Condensate lying in the bottom of the main cannot climb into a takeoff on the top.

Loop the main where demand is distributed. A closed loop feeds a heavy demand point from two directions, reducing pressure loss where the loop geometry and flow distribution provide parallel paths; the reduction is not automatically one-half.

Isolate every branch. A ball valve at each drop allows one station to be serviced without shutting down the shop.

4. Sizing by Pressure Drop

Determine the required pressure at the tool, then allocate allowable losses across piping, filters, dryer, valves and regulators. A percentage allowance is a supplied design criterion, not a universal code rule. In the worked example below, the owner expressly allows 6 psi for distribution piping.

The design inputs are:

Demand in SCFM. Add the rated consumption of every tool that can run at once, applying a realistic duty cycle. A 3/4-inch impact wrench at roughly 5 SCFM running 25 percent of the time contributes about 1.25 SCFM of average load, but the piping must still pass the peak.

Equivalent length. Add the equivalent length of every elbow, tee, valve and filter to the measured run, exactly as you would on a water-distribution sizing exercise.

Line pressure. The denser the air, the lower the loss for the same mass flow, so a 125-psi system loses less in the same pipe than a 90-psi system at the same SCFM.

Worked example. A fabrication shop has a peak simultaneous demand of 80 SCFM at 100 psig , with the most remote drop 220 feet of measured run plus fittings whose equivalent length adds 60 feet , for a total equivalent length of 280 feet . The owner allows 6 psi of loss in the distribution piping. Allowable loss per 100 ft = 6 psi × 100 280 ft = 2.14 psi per 100 ft \text{Allowable loss per 100 ft} = \frac{6\text{ psi} \times 100}{280\text{ ft}} = \mathbf{2.14\text{ psi per 100 ft}} Allowable loss per 100 ft = 280 ft 6 psi × 100 ​ = 2.14 psi per 100 ft

For this illustrative training problem , use the supplied values below at the stated 80 SCFM and 100 psig. These are an exercise exhibit, not a manufacturer-certified sizing chart.

  • Candidate nominal size Supplied loss per 100 equivalent feet Loss over 280 equivalent feet
  • 1 inch 3.0 psi 3.0 × 2.8 = 8.4 psi
  • 1-1/4 inch 2.0 psi 2.0 × 2.8 = 5.6 psi
  • 1-1/2 inch 1.2 psi 1.2 × 2.8 = 3.36 psi

The smallest candidate meeting the 6-psi allowance is 1-1/4 inch . One inch fails, while 1-1/2 inch also passes but is larger. Compare unrounded totals where possible: the exact allowable rate is 6/2.8 = 2.142857 psi per 100 feet. For a real installation, replace the exhibit with the selected piping manufacturer’s data at the actual flow, pressure and temperature and check all other design constraints.

Receiver Sizing

Size the receiver from the actual demand events, allowable pressure swing, compressor controls and manufacturer engineering data. A fixed gallons-per-CFM slogan does not establish adequate storage or safe cycling for every compressor type. Every receiver carries an ASME-stamped pressure vessel rating , a pressure relief valve set at or below the vessel's maximum allowable working pressure , a pressure gauge , and a drain at the low point .

5. OSHA Pneumatic-Tool Safety Requirements

OSHA 29 CFR 1926.302(b) governs pneumatic power tools in construction. Its safety requirements are relevant independently of whether a local exam lists a printed OSHA reference:

1926.302(b)(1) : Pneumatic power tools shall be secured to the hose or whip by some positive means to prevent accidental disconnection.

1926.302(b)(2) : Safety clips or retainers shall be securely installed and maintained on pneumatic impact (percussion) tools to prevent attachments from being accidentally expelled.

1926.302(b)(3) : Pneumatically driven nailers and staplers with automatic fastener feed operating at more than 100 psi at the tool shall have a safety device on the muzzle to prevent ejecting fasteners unless the muzzle contacts the work surface.

1926.302(b)(4) : Compressed air shall not be used for cleaning purposes except where reduced to less than 30 psi , and then only with effective chip guarding and personal protective equipment . The 30-psi limit does not apply to concrete form, mill scale and similar cleaning.

1926.302(b)(5) : The manufacturer's safe operating pressure for hoses, pipes, valves, filters and fittings shall not be exceeded .

1926.302(b)(6) : Hoses shall not be used for hoisting or lowering tools .

1926.302(b)(7) : All hoses exceeding 1/2-inch inside diameter shall have a safety device at the source of supply or branch line to reduce pressure in case of hose failure.

The hose safety-device requirement and the compressed-air cleaning limit address different hazards; apply each to its stated conditions.

Loading diagram... Supplied compressed-air equipment and wet-header example