Study guide

13.4 Oil & Gasoline Storage and Distribution Systems

Florida Journeyman Plumber Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Florida Plumbing Code Administration & Licensure

1.1 DBPR Licensing, CILB Regulations & Journeyman Qualifications 1.2 Permits, Inspections & Code Enforcement 1.3 Florida Construction Lien Law & Business Operations

2 Chapter 2: Sanitary Drainage Fundamentals & DFU Sizing

2.1 Gravity Drainage Principles & Florida DWV Materials 2.2 Drainage Fixture Units (DFU) & Load Values 2.3 Horizontal Branch & Vertical Stack Sizing 2.4 Drainage Fittings, Flow Direction & Change of Direction Rules

3 Chapter 3: Building Drains, Sewers & Special Drainage Systems

3.1 Building Drain & Building Sewer Sizing 3.2 Drainage Cleanouts: Sizing, Clearances & Locations 3.3 Sewage Ejectors, Sumps & Macerating Systems 3.4 Florida High Water Table, Slab Penetrations & Termite Protection

4 Chapter 4: Indirect Waste, Special Waste & Interceptors

4.1 Indirect Waste Systems: Air Gaps vs Air Breaks 4.2 Grease Interceptors: Hydromechanical & Gravity Interceptor Sizing 4.3 Sand, Oil & Specialized Interceptors

5 Chapter 5: Water Supply Systems & WSFU Pipe Sizing

5.1 Potable Water Piping Materials & Installation 5.2 Water Supply Fixture Units (WSFU) & Demand Estimations 5.3 Water Distribution Pipe Sizing Methods 5.4 Water Pressure Control, Boosting & PRVs

6 Chapter 6: Water Heaters, Cross-Connection Control & Reclaimed Water

6.1 Water Heaters & Safety Controls 6.2 Backflow Prevention & Cross-Connection Protection 6.3 Reclaimed Water Systems & Florida Dual-Plumbing Rules 6.4 System Testing, Disinfection & Commissioning

7 Chapter 7: DWV Venting Systems & Sizing

7.1 Principles of Venting & Trap Seal Integrity 7.2 Vent Sizing & Developed Length 7.3 Wet Venting & Horizontal Wet Venting 7.4 Circuit, Loop & Common Venting

8 Chapter 8: Specialized Venting & Air Admittance Valves

8.1 Island Fixture Vents & Foot Venting 8.2 Combination Waste and Vent Systems 8.3 Air Admittance Valves (AAVs) & Engineered Systems

9 Chapter 9: Isometric Drawing Interpretation & Drafting

9.1 Isometric Drawing Fundamentals and Plan Reading 9.2 Drafting Florida DWV Isometric Schematics 9.3 Local Exam Plan-Reading Practice and Self-Audit 9.4 Reading Plumbing Plans, Specifications & Schedules

10 Chapter 10: Fuel Gas Piping & Storm Drainage Systems

10.1 Fuel Gas Fundamentals: Natural Gas vs LP Gas 10.2 Gas Pipe Sizing & Demand Calculations 10.3 Gas Pipe Materials, Installation, Testing & Appliance Connections 10.4 Storm Drainage Sizing & Florida Rainfall Rates 10.5 Appliance Venting, Chimneys & Combustion Air

11 Chapter 11: Trade Mathematics, Accessibility & Jobsite Safety

11.1 Plumbing Math: Grade, Pitch & Elevation Calculations 11.2 Plumbing Math: 45-Degree & Rolling Offsets 11.3 Florida Accessibility Standards for Plumbing Fixtures 11.4 OSHA Construction Safety Standards for Plumbers 11.5 Plumbing Tools, Equipment & System Troubleshooting

12 Chapter 12: Medical Gas & Vacuum Piping Systems (NFPA 99)

12.1 Medical Gas Systems: Categories, Gases & Source Equipment 12.2 Medical Gas Piping Materials, Brazing & Nitrogen Purging 12.3 Station Outlets, Zone Valves, Alarms & Pipe Sizing 12.4 Medical-Surgical Vacuum, WAGD & System Verification

13 Chapter 13: Industrial, Process & Special-Waste Piping

13.1 Compressed Air & Industrial Gas Piping Systems 13.2 Industrial Vacuum Piping Systems 13.3 Process Piping & Steam Distribution Systems 13.4 Oil & Gasoline Storage and Distribution Systems 13.5 Industrial Water Drainage & Waste Pretreatment

14 Chapter 14: Site Utilities, Sewage Disposal & Water Mains

14.1 Onsite Sewage Treatment & Disposal: Septic Tanks & Drainfields 14.2 Sewage Lift Stations & Force Mains 14.3 Water Transmission Mains, Excavation & Heavy Equipment

15 Chapter 15: Pools, Wells, Irrigation, Solar & Fire Protection

15.1 Swimming Pool & Spa Piping Systems 15.2 Water Wells, Pumps & Irrigation Systems 15.3 Solar Water Heating Systems 15.4 Fire Protection Systems & Standpipes (NFPA 14)

13.4 Oil & Gasoline Storage and Distribution Systems

Key Takeaways Explain This Topic AI

FBC-Mechanical Section 1301.2 splits the work: fuel-oil storage systems comply with the Florida Fire Prevention Code, while fuel-oil piping systems comply with FBC-Mechanical Chapter 13.

FBC-Mechanical Section 1303.1 prohibits cast-iron fittings in oil lines and prohibits solder having a melting point of less than 1,000 degrees F, along with unions requiring gaskets or packings and right-or-left couplings.

FBC-Mechanical Section 1302.4 permits nonmetallic fuel-oil pipe only where listed and labeled for flammable and combustible liquids, and only outside, underground.

Where an oil burner is served by a tank any part of which is above the burner inlet and the supply is taken from the top of the tank, Section 1301.4 requires an approved antisiphon valve or other siphon-breaking device in lieu of the shutoff valve.

Florida pollutant storage regulation distinguishes underground systems in Chapter 62-761 from aboveground systems in Chapter 62-762; a local journeyman license does not grant unlimited contracting authority.

Last updated: October 2026

Oil & Gasoline Storage and Distribution Systems

Oil and gasoline work requires a clear distinction between storage, fuel-oil piping and environmental regulation. A local journeyman credential does not itself grant unlimited contracting authority. Confirm the responsible contractor’s licensed scope and the project’s permitting requirements.

1. Three Regulatory Layers

Liquid fuel work in Florida sits under three separate authorities, which must be distinguished:

Layer Authority Governs

Fire and life safety Florida Fire Prevention Code (adopted under FS Chapter 633), which incorporates the NFPA flammable and combustible liquids standards Tank storage , tank location and separation, spill and overfill protection, venting of the tank itself, tank abandonment and removal

Building piping FBC-Mechanical Chapter 13, Fuel Oil Piping and Storage The piping system from the tank to the appliance: materials, joints, supports, pumps, valves and tests

Environmental FDEP Chapter 62-761, F.A.C. (underground storage tank systems) and Chapter 62-762, F.A.C. (aboveground storage tank systems) Registration, secondary containment, release detection, integrity testing, operator training, closure and remediation

FBC-Mechanical Section 1301.2 states the split in one sentence: "Fuel-oil storage systems shall comply with the Florida Fire Prevention Code. Fuel-oil piping systems shall comply with the requirements of this code." Section 1301.1 repeats it — the chapter governs the design, installation, construction and repair of fuel-oil storage and piping systems, while the storage of fuel oil and flammable and combustible liquids shall be in accordance with the Florida Fire Prevention Code .

Important

Scope boundary: pollutant-storage-system contracting is a separate Florida specialty. A journeyman credential is not permission to independently contract for a regulated tank replacement. Confirm the applicable contractor scope and environmental and fire permits; a separate specialty examination’s question count or duration does not describe this local journeyman exam.

2. Tank Types and Terms

Term Meaning

UST Underground storage tank — regulated by FDEP Chapter 62-761. Modern USTs are double-walled fiberglass or jacketed steel with interstitial monitoring.

AST Aboveground storage tank — regulated by FDEP Chapter 62-762. Includes shop-fabricated day tanks and field-erected bulk tanks.

Secondary containment A second barrier — an outer wall, a jacket, or a dike — that captures a release from the primary tank or pipe and holds it for detection.

Interstitial space The annular gap between primary and secondary containment, continuously monitored for liquid or vapor.

Spill containment (spill bucket) The catch basin at the fill connection that captures product spilled when the delivery hose is disconnected.

Overfill prevention An automatic shutoff, flow restrictor or high-level alarm that stops a delivery before the tank is overfilled.

Suction system Product is pulled from the tank by a pump at the dispenser. A safe suction design keeps the piping under vacuum so a line leak draws air rather than pushing product to the soil.

Pressure system A submersible turbine pump inside the tank pushes product to the dispensers — higher throughput, but the piping is under pressure and requires line leak detection.

Day tank A small tank near the burner or generator, refilled automatically from a larger tank, that limits the fuel inventory inside the building.

3. Fuel-Oil Piping Materials (FBC-M Table 1302.3)

Section 1302.2 governs first: all materials shall be rated for the operating temperatures and pressures of the system and shall be compatible with the type of liquid. Table 1302.3 then lists the approved families:

  • Material Standards
  • Copper or copper-alloy pipe and fittings ASTM B42; ASTM B43; ASTM B302; ASTM F3226

Copper or copper-alloy tubing and fittings (Type K, L or M) ASTM B75; ASTM B88; ASTM B135; ASTM B280; ASME B16.51; ASTM F3226

  • Steel and stainless steel pipe and fittings ASTM A53; ASTM A106; ASTM A312; ASTM F3226
  • Steel and stainless steel tubing and fittings ASTM A254; ASTM A539; ASTM A269; ASTM F3226
  • Nonmetallic pipe ASTM D2996, listed and labeled for flammable and combustible liquids
  • Labeled pipe Per Section 1302.4

Section 1302.4 is the one to memorize : nonmetallic pipe shall be listed and labeled as acceptable for the intended application for flammable and combustible liquids , and shall be installed only outside, underground . Fiberglass product piping belongs in the tank field, never inside the building.

4. Prohibited Joints and Materials

FBC-Mechanical Section 1303.1 identifies the following prohibited joints/materials:

Unions requiring gaskets or packings shall not be used in oil lines.

Right or left couplings shall not be used in oil lines.

Sweat fittings employing solder having a melting point of less than 1,000 degrees F (538 degrees C) shall not be used in oil lines. This excludes the stated low-melting soldered joints; it does not mean every permitted copper connection must be brazed. Select an approved joining method and components for the actual fuel-oil service.

Cast-iron fittings shall not be used. Cast iron is brittle and fractures under the thermal and mechanical shock of a fire or a vehicle impact.

Joints and connections shall be approved and of a type approved for fuel-oil piping systems , threaded joints made tight with a suitable lubricant or pipe compound, and all joints tight for the pressure required by test.

Other workmanship requirements:

1303.2 Preparation of pipe ends : pipe shall be cut square, reamed and chamfered , free of burrs and obstructions, with full-bore openings and no undercut.

1303.3.1 Brazed joints : all joint surfaces cleaned, approved flux applied where required, brazed with filler metal conforming to AWS A5.8 .

1303.3.3 Threaded joints : threads conform to ASME B1.20.1 ; pipe-joint compound or tape applied on the male threads only .

1303.1.1 Dissimilar materials : joints between different metallic piping materials shall be made with approved dielectric fittings or brass and copper-alloy converter fittings.

1303.9.1 : mechanical joints on steel or stainless pipe use an approved elastomeric seal and shall be installed outside, underground, unless otherwise approved .

1303.11 Piping protection : proper allowance shall be made for expansion, contraction, jarring and vibration, and piping other than tubing connected to underground tanks — except straight fill lines and test wells — shall be provided with flexible connectors or otherwise arranged to permit the tanks to settle without impairing the tightness of the piping connections . Buried tanks move; rigid pipe welded to a settling tank shears.

5. Pumps, Antisiphon Protection and Sizing

Section 1302.7 Pumps : pumps that are not part of an appliance shall be of the positive-displacement type , shall automatically shut off the supply when not in operation , and shall be listed and labeled in accordance with UL 343 .

Section 1301.4 Antisiphon : where an oil burner is served by a tank any part of which is above the level of the burner inlet connection , and where the fuel supply line is taken from the top of the tank , an approved antisiphon valve or other siphon-breaking device shall be installed in lieu of the shutoff valve . This is the classic basement-burner / attic-tank hazard: if the supply line breaks, gravity can siphon fuel through the broken line.

Section 1302.8 : flexible connectors and hoses shall be listed and labeled for flammable and combustible liquids .

Section 1305.1 Size : the system shall be sized for the maximum capacity of fuel oil required, and the minimum size of a supply line is 3/8 inch inside diameter nominal pipe, or 3/8 inch outside diameter tubing .

Section 1301.3 Fuel type : an appliance shall be designed for the fuel to which it will be connected, and shall not be converted to a different fuel without reapproval from the code official.

Section 1301.5 Abandonment : all exterior above-grade fill piping shall be removed when tanks are abandoned or removed , and tank abandonment and removal shall comply with the Florida Fire Prevention Code. An abandoned fill pipe standing at the curb is an invitation for a delivery driver to pump product into a tank that is no longer there.

6. Where the Plumbing Trade Actually Touches This Work

Three intersections come up constantly on Florida jobs, and all three route back to the plumbing code:

Shop and garage floor drainage. A repair garage with floor or trench drains requires an oil separator under FPC Section 1003.4 , sized under 1003.4.2.2 at 6 cubic feet for the first 100 square feet plus 1 cubic foot per additional 100 square feet, with the 2-foot depth and 18-inch outlet water seal of 1003.4.2.1.

Generator and boiler day-tank drains and overflows. Route fuel to the approved fuel-return, containment or hazardous-waste management arrangement for that installation. An indirect connection or air gap does not authorize fuel discharge into a sanitary drain. Confirm overflow capacity, destination, spill control and the applicable fire/environmental requirements.

Emergency generator installations. The plumbing contractor commonly runs the fuel-oil piping from a diesel day tank to a standby generator, which is squarely FBC-Mechanical Chapter 13 work — approved copper or steel connections, no cast iron, no low-melting solder, antisiphon protection where the tank sits above the burner, and flexible connections where the pipe meets a tank that can settle.

Loading diagram... Three regulatory layers over Florida liquid fuel work