Study guide
15.3 Solar Water Heating Systems
Florida Journeyman Plumber Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Florida Plumbing Code Administration & Licensure
1.1 DBPR Licensing, CILB Regulations & Journeyman Qualifications 1.2 Permits, Inspections & Code Enforcement 1.3 Florida Construction Lien Law & Business Operations
2 Chapter 2: Sanitary Drainage Fundamentals & DFU Sizing
2.1 Gravity Drainage Principles & Florida DWV Materials 2.2 Drainage Fixture Units (DFU) & Load Values 2.3 Horizontal Branch & Vertical Stack Sizing 2.4 Drainage Fittings, Flow Direction & Change of Direction Rules
3 Chapter 3: Building Drains, Sewers & Special Drainage Systems
3.1 Building Drain & Building Sewer Sizing 3.2 Drainage Cleanouts: Sizing, Clearances & Locations 3.3 Sewage Ejectors, Sumps & Macerating Systems 3.4 Florida High Water Table, Slab Penetrations & Termite Protection
4 Chapter 4: Indirect Waste, Special Waste & Interceptors
4.1 Indirect Waste Systems: Air Gaps vs Air Breaks 4.2 Grease Interceptors: Hydromechanical & Gravity Interceptor Sizing 4.3 Sand, Oil & Specialized Interceptors
5 Chapter 5: Water Supply Systems & WSFU Pipe Sizing
5.1 Potable Water Piping Materials & Installation 5.2 Water Supply Fixture Units (WSFU) & Demand Estimations 5.3 Water Distribution Pipe Sizing Methods 5.4 Water Pressure Control, Boosting & PRVs
6 Chapter 6: Water Heaters, Cross-Connection Control & Reclaimed Water
6.1 Water Heaters & Safety Controls 6.2 Backflow Prevention & Cross-Connection Protection 6.3 Reclaimed Water Systems & Florida Dual-Plumbing Rules 6.4 System Testing, Disinfection & Commissioning
7 Chapter 7: DWV Venting Systems & Sizing
7.1 Principles of Venting & Trap Seal Integrity 7.2 Vent Sizing & Developed Length 7.3 Wet Venting & Horizontal Wet Venting 7.4 Circuit, Loop & Common Venting
8 Chapter 8: Specialized Venting & Air Admittance Valves
8.1 Island Fixture Vents & Foot Venting 8.2 Combination Waste and Vent Systems 8.3 Air Admittance Valves (AAVs) & Engineered Systems
9 Chapter 9: Isometric Drawing Interpretation & Drafting
9.1 Isometric Drawing Fundamentals and Plan Reading 9.2 Drafting Florida DWV Isometric Schematics 9.3 Local Exam Plan-Reading Practice and Self-Audit 9.4 Reading Plumbing Plans, Specifications & Schedules
10 Chapter 10: Fuel Gas Piping & Storm Drainage Systems
10.1 Fuel Gas Fundamentals: Natural Gas vs LP Gas 10.2 Gas Pipe Sizing & Demand Calculations 10.3 Gas Pipe Materials, Installation, Testing & Appliance Connections 10.4 Storm Drainage Sizing & Florida Rainfall Rates 10.5 Appliance Venting, Chimneys & Combustion Air
11 Chapter 11: Trade Mathematics, Accessibility & Jobsite Safety
11.1 Plumbing Math: Grade, Pitch & Elevation Calculations 11.2 Plumbing Math: 45-Degree & Rolling Offsets 11.3 Florida Accessibility Standards for Plumbing Fixtures 11.4 OSHA Construction Safety Standards for Plumbers 11.5 Plumbing Tools, Equipment & System Troubleshooting
12 Chapter 12: Medical Gas & Vacuum Piping Systems (NFPA 99)
12.1 Medical Gas Systems: Categories, Gases & Source Equipment 12.2 Medical Gas Piping Materials, Brazing & Nitrogen Purging 12.3 Station Outlets, Zone Valves, Alarms & Pipe Sizing 12.4 Medical-Surgical Vacuum, WAGD & System Verification
13 Chapter 13: Industrial, Process & Special-Waste Piping
13.1 Compressed Air & Industrial Gas Piping Systems 13.2 Industrial Vacuum Piping Systems 13.3 Process Piping & Steam Distribution Systems 13.4 Oil & Gasoline Storage and Distribution Systems 13.5 Industrial Water Drainage & Waste Pretreatment
14 Chapter 14: Site Utilities, Sewage Disposal & Water Mains
14.1 Onsite Sewage Treatment & Disposal: Septic Tanks & Drainfields 14.2 Sewage Lift Stations & Force Mains 14.3 Water Transmission Mains, Excavation & Heavy Equipment
15 Chapter 15: Pools, Wells, Irrigation, Solar & Fire Protection
15.1 Swimming Pool & Spa Piping Systems 15.2 Water Wells, Pumps & Irrigation Systems 15.3 Solar Water Heating Systems 15.4 Fire Protection Systems & Standpipes (NFPA 14)
15.3 Solar Water Heating Systems
Key Takeaways Explain This Topic AI
Solar freeze protection must match the actual site and approved system design; Florida’s climate does not eliminate freeze risk.
FPC Section 612.1 and FBC-Mechanical Section 1401.1 place the construction, installation, alteration and repair of solar systems for space heating or cooling, domestic hot water, swimming pool heating and process heating under the Florida Building Code, Mechanical.
FBC-Mechanical Section 1401.2 requires potable water supplies to solar systems to be protected against contamination in accordance with the Florida Building Code, Plumbing, unless all system piping is part of the potable distribution system and all components are listed for potable water use.
FBC-Mechanical Section 1403.1 requires the flash point of the heat transfer fluid to be not less than 50 degrees F above the design maximum nonoperating stagnation temperature in the collector, and Section 1403.2 prohibits flammable liquids or gases as heat transfer fluids.
FBC-Mechanical Section 1402.5.1 requires pressure and temperature relief protection on every section in which excessive pressure can develop, arranged so that a section cannot be valved off or isolated from its relief device.
Last updated: October 2026
Solar Water Heating Systems
Solar thermal systems require coordinated plumbing, mechanical and structural decisions. FSEC educational material is useful background, but a contractor reference list is not permission to bring a solar manual into a local journeyman exam. Use the local provider’s approved list and book rules.
1. Which Code Governs
The plumbing-code provisions point the same direction, and knowing the numbers keeps you out of Section 505:
FPC Section 601.2, Solar Energy Utilization : solar energy systems used for heating potable water, or using an independent medium for heating potable water, shall comply with the applicable requirements of the code.
FPC Section 502.1 : solar thermal water heating systems shall conform to the Florida Building Code, Mechanical .
FPC Section 612.1, Solar Systems : "The construction, installation, alterations and repair of systems, equipment and appliances intended to utilize solar energy for space heating or cooling, domestic hot water heating, swimming pool heating or process heating shall be in accordance with the Florida Building Code, Mechanical."
FBC-Mechanical Chapter 14, Solar Systems , then carries the substance in Sections 1401 through 1404.
Warning
FPC Section 505 is Insulation , not solar. Chapter 5 of the plumbing volume runs 501 General, 502 Installation, 503 Connections, 504 Safety Devices, 505 Insulation — and 505.1 is a single sentence requiring unfired hot water storage tanks to be insulated to R-12.5. Solar lives at FPC 612 and FBC-M Chapter 14 . Older prep material that cites "FPC 505" for solar is using superseded numbering.
2. System Configurations
Florida’s climate does not eliminate freeze exposure. Select the system and protection method for the actual site, collector behavior and expected operating and power-failure conditions. ICC’s solar guidance explicitly discusses freeze prevention for direct systems in Florida, and FSEC Standard 104-10 Section 6.2.5 addresses protection under the environmental conditions expected in actual use.
Configuration How It Works Florida Fit
Direct (open loop) Potable water itself circulates through the collector Common in Florida. Simple, efficient, no heat exchanger. Vulnerable to freeze and to scaling in hard water.
Indirect (closed loop) A separate heat transfer fluid circulates through the collector and gives up heat through a heat exchanger Required wherever freeze protection fluid or a non-potable medium is used
Thermosiphon Storage tank mounted above the collector; hot water rises without a pump No pump, no controller; needs structural support for a roof-mounted tank
Active pumped A differential controller starts a circulator when the collector is hotter than the tank by a set margin The standard active Florida system
Drainback Collector loop drains by gravity into a drainback tank whenever the pump stops Elegant freeze and stagnation protection; requires continuous pitch on all collector piping
Integral collector storage (ICS) / batch Tank and absorber are the same vessel Simple, but heavy on the roof and prone to overnight heat loss
Solar pool heating Unglazed polymer collectors heat pool water directly through the existing filter loop Pool-water heating; use the selected collector’s operating limits
Many domestic designs include conventional backup to meet hot-water demand when solar input is insufficient. Whether backup is provided and how it is sized follows the actual performance requirement and approved design; it is not a universal feature of every solar system.
3. Protecting the Potable Water
This is where the plumbing trade earns its place on the roof.
FBC-Mechanical Section 1401.2, Potable Water Supply : potable water supplies to solar systems shall be protected against contamination in accordance with the Florida Building Code, Plumbing . One exception applies: where all solar system piping is part of the potable water distribution system in accordance with the plumbing code and all components of the piping system are listed for potable water use , cross-connection protection measures are not required. A pure direct-loop system built entirely of potable-listed components does not need a backflow assembly; otherwise the exception is unavailable and the actual system needs the appropriate approved protection, including exchanger separation and any makeup-supply backflow protection.
FBC-Mechanical Section 1401.3, Heat Exchangers : heat exchangers used in domestic water-heating systems shall be approved for the intended use , and the system shall have adequate protection to ensure that the potability of the water supply and distribution system is properly safeguarded .
FPC 608.17.3 distinguishes essentially toxic from essentially nontoxic transfer fluid. Assess the complete formulation and approved exchanger application:
A double-wall heat exchanger places two separate walls between the transfer fluid and the potable water, with a vented space between them so that a failure of either wall leaks visibly to atmosphere rather than into the drinking water. This is the required separation for essentially toxic transfer fluid; resolve unknown toxicity before approving an exchanger — for example an essentially toxic ethylene-glycol formulation. Determine toxicity from the complete formulation , including concentration and additives; not every corrosion inhibitor makes a fluid toxic.
A single-wall heat exchanger is used only where the transfer fluid is non-toxic — an appropriately evaluated nontoxic formulation, for example — and where the design otherwise satisfies the AHJ.
4. Heat Transfer Fluids (FBC-M Section 1403)
Two rules, and both are quotable:
1403.1 Flash Point : "The flash point of the actual heat transfer fluid utilized in a solar system shall be not less than 50 degrees F (28 degrees C) above the design maximum nonoperating (no-flow) temperature of the fluid attained in the collector."
1403.2 Flammable Gases and Liquids : "A flammable liquid or gas shall not be utilized as a heat transfer fluid."
The reason is stagnation . When a pump fails or power is lost on a sunny Florida afternoon, a glazed collector with no flow through it climbs far above its operating temperature — a condition the code calls the design maximum nonoperating, or no-flow, temperature. If the fluid's flash point sits near that temperature, a leak near ignition sources can create a fire hazard. The 50-degree margin is the safety factor, and it explains why Florida systems either use water, use a fluid with a high flash point, or use drainback so there is no fluid in the collector to stagnate.
5. Required Equipment and Protection (FBC-M Section 1402)
Requirement Section
Access shall be provided to solar equipment for maintenance; systems shall not obstruct doors, windows or other components requiring operation or access 1402.1
Solar equipment exposed to vehicular traffic shall be installed not less than 6 feet above the finished floor , unless protected from motor vehicle impact 1402.2
Roof-mounted collectors that also serve as a roof covering shall conform to the roof covering requirements of the Florida Building Code, Building 1402.4
Collector arrays and supporting construction mounted on or above the roof covering shall meet the noncombustible/fire-retardant-treated provisions to the extent required for the building’s roof-construction type , with the stated approved-plastic-cover exception; the roof must support the imposed loads 1402.4.1, 1402.4.2
Pressure and temperature : components containing pressurized fluids shall be protected against pressures and temperatures exceeding design limits with a pressure and temperature relief valve, and each section in which excessive pressures are capable of developing shall have a relief device located so that the section cannot be valved off or otherwise isolated from a relief device 1402.5.1
Vacuum : components subjected to vacuum in operation or during shutdown shall be designed to withstand it or be protected with vacuum relief valves 1402.5.2
Protection from freezing : system components shall be protected from damage by freezing of heat transfer liquids at the lowest ambient temperatures that will be encountered during operation 1402.5.3
Expansion tanks : liquid single-phase solar energy systems shall be equipped with expansion tanks 1402.5.4
Penetrations : roof and wall penetrations shall be flashed and sealed to prevent entry of water, rodents and insects 1402.6
Collector labeling : factory-built solar thermal collectors shall bear a label showing the manufacturer's name and serial or certification number, collector dry weight , and maximum allowable operating and nonoperating temperatures and pressure 1404.1
Important
Check each isolatable section under 1402.5.1. It is not enough to put a relief valve on the storage tank. Any section of the loop that can be isolated by valves and can then develop excessive pressure needs its own relief device, positioned so a closed valve cannot separate the fluid from the relief. A solar loop isolated for service on a sunny day is a pressure vessel with a heat source attached.
Florida-specific design checks include roof wind loads and attachment, the actual freeze exposure and approved protection method, and water chemistry. Follow the approved system instructions for drainback, an indirect antifreeze loop or other permitted protection; do not assume ordinary circulation alone remains effective during a power outage. Evaluate scaling and treatment with the equipment manufacturer rather than assuming every fluid or treatment is suitable for potable service.
6. Solar Pool Heating
Solar pool heating is the volume application in Florida and it is deliberately simple: unglazed polymer collectors are plumbed into the existing pool filter loop downstream of the filter, with a three-way diverter valve sending flow to the roof when the controller calls for heat and bypassing it when it does not. Because a pool operates near ambient temperature, unglazed collectors with no insulation and no glazing are the efficient choice, and a direct pool-water collector circuit may not use a heat exchanger. Any potable makeup connection still requires appropriate backflow protection ; calling the circulation water nonpotable does not eliminate that cross-connection.
The design points are pool-side, not potable-side:
Collector area is conventionally sized as a percentage of pool surface area, and the FSEC manual gives the Florida guidance.
Evaluate startup and operating head separately. Filling a drained roof array can require static lift. In a fully filled closed circulation path returning to the same pool, upward and downward static elevations cancel in steady operation; pump head must still cover friction, equipment losses and required operating conditions. Drainback and air-admission behavior can change the case.
Where the selected system uses automatic drain-down , unobstructed drainage protects the panels when flow stops.
Check valves, vacuum relief and drainback paths follow the manufacturer’s arrangement; placing a check valve indiscriminately can obstruct required drainage.
The heater arrangement still satisfies FBC-Residential Section R4501.6.4 , which sends water flow through any heater, bypass plumbing, back-siphoning protection and heat sinks to the manufacturer's recommendations .