Study guide
7.3 Architectural & Structural Metal Roofing Systems
Florida Certified Roofing Contractor CCC
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Exam Overview
0.1 Current Exam Facts: Trade Knowledge & Business & Finance
2 Chapter 1: Licensing, Florida Statutes & Business Setup
1.1 DBPR, CILB & Florida Statute 489 Licensing Requirements 1.2 Entity Selection, Financial Stability & Credit Requirements 1.3 Continuing Education, Renewal & Disciplinary Actions
3 Chapter 2: Florida Roofing Law, Contracts & Consumer Protection
2.1 Florida Construction Lien Law (F.S. 713) & Notice to Owner Rules 2.2 Roofing Contract Requirements, Disclosures & Consumer Protections 2.3 Dispute Resolution, Construction Defects & Warranty Laws
4 Chapter 3: Accounting, Taxes, Payroll & Financial Management
3.1 Contractor Financial Statements, Ratios & Working Capital 3.2 Federal, State & Local Tax Compliance and Payroll Taxes 3.3 Insurance, Workers' Compensation & Risk Management 3.4 Managing Human Resources & Employment Law 3.5 Environmental Compliance: NPDES, Stormwater & Site Controls
5 Chapter 4: Roofing Estimating, Job Site & Project Management
4.1 Roofing Estimating, Takeoffs & Material Calculations 4.2 Job Site Operations, Scheduling & Quality Control 4.3 Subcontractor Management & Code Compliance Inspections
6 Chapter 5: Equipment, OSHA Safety & Fall Protection
5.1 OSHA 1926 Subpart M Fall Protection Standards for Roofing 5.2 Roofing Equipment Safety: Kettles, Hoists, Ladders & Scaffolding 5.3 Personal Protective Equipment, Hazardous Materials & Heat Stress
7 Chapter 6: Built-Up Roofing (BUR) & Modified Bitumen Systems
6.1 Built-Up Roof (BUR) System Design, Substrates & Insulation 6.2 BUR Application Techniques: Hot Asphalt, Torch & Cold-Applied 6.3 Modified Bitumen (APP & SBS) Systems & Flashings 6.4 BUR & Mod Bit Maintenance, Repairs & Test Cuts
8 Chapter 7: Single-Ply Roofing & Architectural Metal Systems
7.1 Single-Ply Membranes: TPO, EPDM & PVC Systems 7.2 Single-Ply Attachment Methods: Adhered, Mechanically Fastened & Ballasted 7.3 Architectural & Structural Metal Roofing Systems 7.4 Metal Roof Flashing, Underlayments & Thermal Movement
9 Chapter 8: Steep-Slope Roof Assemblies & Fastening Systems
8.1 Asphalt Shingle Installation, Underlayment & Ventilation Requirements 8.2 Wood Shingles, Wood Shakes & Synthetic Slate Materials 8.3 Concrete & Clay Tile Roof Systems: Loading, Layout & Underlayment 8.4 Tile Roof Fastening: Mechanical, Mortar & Two-Component Adhesive Systems
10 Chapter 9: Waterproofing, Drainage & High-Velocity Hurricane Zone (HVHZ) Provisions
9.1 Below-Grade & Above-Grade Membrane Waterproofing & Dampproofing 9.2 Roof Drains, Scuppers, Gutters, Downspouts & Overflow Systems 9.3 Florida Building Code (FBC) General Roofing Requirements 9.4 High-Velocity Hurricane Zone (HVHZ) Standards (Miami-Dade/Broward FBC Sec 1512-1525)
7.3 Architectural & Structural Metal Roofing Systems
Key Takeaways Explain This Topic AI
Architectural metal roofing panels require solid continuous substrate decking and steep slope water shedding (typically 3:12 minimum), whereas Structural metal panels possess structural beam strength to span open framing purlins.
Standing seam metal panel profiles (snap-lock, single-lock 90°, and double-lock 180° mechanical seams) conceal panel fasteners, avoiding through-panel penetrations.
Thermal movement in metal panels must be accommodated using two-piece sliding expansion clips anchored to the deck, preventing panel buckling and fastener fatigue.
Exposed fastener metal panels (such as 5-V Crimp and corrugated sheets) rely on gasketed screws, making them susceptible to washer degradation and thermal slotting over time.
Oil canning is a visible aesthetic surface waviness in flat metal panel faces that can be minimized using factory-applied striations, stiffening ribs, heavier metal gauges, and flat substrate framing.
Last updated: July 2026
7.3 Architectural & Structural Metal Roofing Systems
Metal roofing is one of the fastest-growing roofing sectors in Florida, offering high wind resistance, extended service lives (50+ years), Class A fire ratings, and high solar reflectance. For the Florida Roofing Contractor examination, candidates must distinguish clearly between Architectural Metal Roofing Systems and Structural Metal Roofing Systems , master panel seam profiles, design for thermal movement, and implement oil canning mitigation strategies.
Classification: Architectural vs. Structural Metal Panels
Metal roof panels are engineered according to their structural load capacity and slope requirement: +-----------------------------------------------------------------------------------+
- | METAL ROOFING SYSTEMS |
- +-----------------------------------------------------------------------------------+
- |
- +-----------------------+-----------------------+
- | |
- v v
- ARCHITECTURAL METAL PANELS STRUCTURAL METAL PANELS
- Hydrodynamic / Water-shedding - Hydrostatic / Water-barrier
- REQUIRES SOLID DECK (Plywood/OSB) - SPANS OPEN PURLINS (No deck required)
- Min. Slope: 3:12 (2:12 w/ sealant) - Min. Slope: 1/2:12 or 1/4:12
- Lower seam profile (1" to 1.5") - Tall trapezoidal seam (2" to 3")
- Concealed or exposed fasteners - Heavy mechanical field seaming
- 1. Architectural Metal Panel Systems
Function : Designed primarily as water-shedding (hydrodynamic) roof coverings.
Substrate Requirement : Architectural panels possess limited beam strength and MUST be supported by a continuous solid roof deck (e.g., nominal 19/32-inch exterior grade plywood, OSB, tongue-and-groove planking, or structural concrete).
Minimum Roof Slope : Standard architectural standing seam systems require a minimum roof slope of 3:12 (25%) . When installed on slopes between 2:12 and 3:12, continuous in-seam sealant tape must be applied.
Panel Profiles : Includes 5-V Crimp, traditional standing seam, snap-lock profiles, metal shingles, and tile-profile metal panels.
2. Structural Metal Panel Systems
Function : Engineered as water-barrier (hydrostatic) assemblies capable of withstanding standing water head pressures under heavy rainfall.
Open Purlin Spanning : Structural panels feature deep vertical ribs (typically 2-inch to 3-inch tall trapezoidal or vertical legs) that act as structural beam members. They can be installed directly over open structural framing purlins (Z-purlins or C-channels spaced 4 to 5 feet on-center) without solid wood decking.
Minimum Roof Slope : Structural standing seam systems can be installed on ultra-low slopes down to 1/4:12 (1/4 inch per foot) or 1/2:12 , provided the seams contain factory-applied butyl mastic sealant and are mechanically seamed using a electric field-seaming machine.
- Panel Profiles & Fastening Systems
- Standing Seam Profiles (Concealed Fasteners)
Standing seam roofing consists of interlocking vertical panel legs that enclose and conceal panel clips and fasteners beneath the standing rib. STANDING SEAM PROFILES:
1. Snap-Lock Profile 2. Single-Lock (90°) 3. Double-Lock (180°)
- || Clip |--| Clip |---| Clip
- || | | | | | | | |
- __/ \_|__ __/ \_|__ __/ |\_|__
Snap-Lock Standing Seam : The female panel leg snaps vertically over the male leg, engaging an integral factory locking notch over a concealed panel clip. It requires no mechanical field seaming tools. Suitable for slopes 3:12 and greater.
Single-Lock (90° Mechanical Seam) : Panels are laid over clips, and a motorized electric field seamer motorized tool bends the female leg 90 degrees over the male leg. Used on slopes 2:12 and greater.
Double-Lock (180° Mechanical Seam) : The field seamer performs two full folding passes, bending the seam a full 180 degrees into a double-fold hook. This creates an airtight, watertight structural seam approved for low slopes (down to 1/2:12) and High Velocity Hurricane Zones (HVHZ).
Exposed Fastener Panel Systems (5-V Crimp & Corrugated)
Exposed fastener systems drive gasketed screws directly through the flat panel face into the wood decking or purlins.
5-V Crimp : Traditional Florida architectural metal roof featuring inverted V-grooves. Screws with EPDM sealing washers are driven through the flat panel pans or immediately adjacent to the crimp ribs.
Vulnerability : Thermal expansion causes panels to drag across exposed screws, elongating screw holes ("thermal slotting") and degrading neoprene washers after 10–15 years, requiring screw replacement.
Thermal Movement & Expansion Clip Mechanics
All metals expand when heated by direct sunlight and contract when cooling at night. In Florida, metal roof surface temperatures can range from 40°F in winter to 170°F+ in summer —a delta of 130°F.
Thermal Expansion Equation & Rates
Thermal movement is calculated using the metal's coefficient of linear thermal expansion ( α \alpha α ): Δ L = L × α × Δ T \Delta L = L \times \alpha \times \Delta T Δ L = L × α × Δ T
Where Δ L \Delta L Δ L is change in panel length, L L L is original length, and Δ T \Delta T Δ T is temperature change.
Aluminum : Moves significantly ( α ≈ 12.8 × 10 − 6 in/in/°F \alpha \approx 12.8 \times 10^{-6} \text{ in/in/°F} α ≈ 12.8 × 1 0 − 6 in/in/°F ). A 40-foot aluminum panel will expand nearly 0.80 inches over a 130°F range.
Steel (Galvanized / Galvalume) : Moves moderately ( α ≈ 6.7 × 10 − 6 in/in/°F \alpha \approx 6.7 \times 10^{-6} \text{ in/in/°F} α ≈ 6.7 × 1 0 − 6 in/in/°F ). A 40-foot steel panel expands roughly 0.42 inches over the same temperature swing.
Copper : Intermediate expansion ( α ≈ 9.3 × 10 − 6 in/in/°F \alpha \approx 9.3 \times 10^{-6} \text{ in/in/°F} α ≈ 9.3 × 1 0 − 6 in/in/°F ).
Fixed vs. Sliding Expansion Clips
To accommodate thermal movement without buckling panels or shearing fasteners, standing seam systems utilize specialized mounting clips: SLIDING EXPANSION CLIP ASSEMBLY:
- [Top Sliding Tab - Moves with Panel]
- +---------------+ <=== Moves Left / Right with Thermal Cycle
- | =========== |
- +-------+-------+
- | <-------- Stainless Steel Base
- +-------+-------+
- | [Anchor Screws into Deck] |
Fixed Clips : Solid one-piece clips anchored firmly to the deck. They lock the panel at one single reference line (typically at the ridge line or eave line), forcing all panel expansion to move toward the opposite end.
Sliding (Expansion) Clips : Two-piece clip assemblies featuring a base anchored to the deck and an upper tab that slides horizontally within a slotted track inside the standing seam. Sliding clips allow panels to expand and contract freely up to 1.5 inches to 2.0 inches total travel.
Oil Canning: Causes, Identification & Prevention
Oil canning is defined by the National Roofing Contractors Association (NRCA) as a visible, stress-induced surface waviness in the flat areas of metal panels. While oil canning does not compromise the structural integrity or waterproofing of the roof, it is a frequent source of owner disputes. CROSS-SECTION OF PANEL WITH OIL CANNING MITIGATION:
- Flat Panel (Prone to Oil Canning) Panel with Stiffening Ribs / Striations
- =================================== ====/\====/\====/\====/\====/\====
- [Reflects light unevenly / wavy] [Breaks up light / absorbs tension]
- Primary Causes of Oil Canning
Substrate Imperfections : Uneven deck sheathing, misaligned purlins, or warped wood joists force panels into twisted planes.
Over-Tightening Clips : Screwing clip bases too tightly distorts the standing seam vertical leg.
Roll-Forming Stresses : Residual stress induced into sheet coil metal during factory roll-forming.
Thermal Expansion Restraint : Pinning panel ends without adequate expansion clearance.
Wide Unribbed Flat Pans : Specifying wide, smooth, flat panel pans (e.g., 18-inch to 24-inch wide flat sheets).
Prevention & Mitigation Techniques
Specify Striations or Pencil Ribs : Requesting factory-applied longitudinal striations, pencil ribs, or wave profiles in the panel flat breaks up light reflection and absorbs internal stress.
Use Heavier Metal Gauges : Select 24-gauge steel instead of 26-gauge, or 0.032-inch / 0.040-inch aluminum instead of 0.025-inch.
Verify Substrate Flatness : Ensure wood or steel sub-framing does not deviate more than 1/8 inch in 10 feet .
Narrow Panel Widths : Specify 12-inch or 16-inch panel widths rather than 18-inch or 20-inch widths.
Use Backer Rod or Tension Strips : Place narrow foam backer rod strips beneath the center of flat panel pans to push the metal slightly outward into a uniform crown.
Metal Roofing System Matrix
- Feature Architectural Standing Seam Structural Standing Seam Exposed Fastener (5-V Crimp)
- Substrate Deck Continuous Solid Deck Required Spans Open Purlins Continuous Solid Deck Required
- Min. Roof Slope 3:12 (2:12 w/ sealant) 1/4:12 or 1/2:12 3:12
- Seam Fasteners Concealed Clips Concealed Clips Exposed Washer Screws
- Thermal Movement Handled by Sliding Clips Handled by Sliding Clips Restricted (Causes Hole Slotting)
- Seam Profiles Snap-Lock, 90° Single-Lock 180° Double-Lock Mechanical Overlapping Lap Rib
- Hydrostatic Rating Hydrodynamic (Water Shedding) Hydrostatic (Water Barrier) Hydrodynamic
- Wind Resistance High (Up to HVHZ Standards) Highest (Heavy Structural Ratings) Moderate