Study guide

10.1 Secondary Process Fundamentals

Florida Water/Wastewater Operator Study Guide Exam

Track your progress as you read

Finished sections get a check mark.

1 Introduction & FDEP Certification Framework

1.1 Current Exam Facts & PSI Logistics 1.2 License Families, Classes A–D & Distribution Levels 1.3 Examination Eligibility, Approved Courses & Linear Progression 1.4 Licensure Experience, Fees, Renewal & CEUs

2 Florida Regulations & Water Law

2.1 Chapter 62-602 Operator Certification Rules 2.2 FAC 62-550 Drinking Water Standards & SDWA Primacy 2.3 FAC 62-600 Wastewater & AWT 5-5-3-1 Standards 2.4 FAC 62-610 Reclaimed Water Reuse Rules

3 Source Water & Florida Hydrogeology

3.1 Characteristics of Source Water & Contaminants 3.2 Floridan Aquifer, Wells & Saltwater Intrusion 3.3 Reservoir, Wellfield Management & Water Management Districts

4 Coagulation, Flocculation & Sedimentation

4.1 Coagulation Chemistry & Jar Testing 4.2 Flocculation Process Control 4.3 Clarification & Sedimentation

5 Filtration & Membrane Processes

5.1 Granular Media Filtration Theory 5.2 Filter Operation, Backwash & Troubleshooting 5.3 Membrane Filtration & Reverse Osmosis (Florida RO)

6 Softening, Iron/Manganese & Taste/Odor Control

6.1 Lime Softening & Ion Exchange 6.2 Iron and Manganese Control 6.3 Taste and Odor Control & Aeration

7 Disinfection & Disinfectant Byproducts

7.1 Chlorination Chemistry & Residual Control 7.2 CT Calculations & Pathogen Inactivation 7.3 Alternative Disinfectants (Chloramines, ClO2, Ozone, UV) 7.4 DBP Formation, Stage 1/2 Rules & Compliance

8 Corrosion Control & Chemical Treatment

8.1 Corrosion Control & Lead and Copper Rule 8.2 Chemical Treatment, Fluoridation & Feed Systems 8.3 Residuals Disposal & Waste Handling

9 Wastewater Collection, Preliminary & Primary Treatment

9.1 Collection Systems, Lift Stations & SSO Reporting 9.2 Preliminary Treatment: Screening & Grit 9.3 Primary Sedimentation 9.4 Wastewater Characteristics & Plant Loadings

10 Secondary Treatment & Activated Sludge

10.1 Secondary Process Fundamentals 10.2 Activated Sludge Process Control 10.3 Activated Sludge Troubleshooting 10.4 Fixed-Film, Package Plants & Lagoons

11 Nutrient Removal, AWT & Reuse

11.1 Biological Nutrient Removal (N & P) 11.2 Florida AWT 5-5-3-1 Standards 11.3 Effluent Disposal Options 11.4 Reclaimed Water Systems & FAC 62-610 Practice

12 Solids Handling & Biosolids

12.1 Sludge Thickening & Digestion 12.2 Dewatering & Residuals Disposal 12.3 Biosolids Stabilization & Land Application Basics

13 Distribution Systems & Hydraulics

13.1 Distribution Network Design & Operations 13.2 Pipes, Valves, Hydrants & Appurtenances 13.3 Hydraulics, Pressure & Pumping 13.4 Main Disinfection, Breaks & Repair

14 Cross-Connection, Storage & Distribution Water Quality

14.1 Cross-Connection Control & Backflow Prevention 14.2 Storage Tanks & Reservoirs 14.3 Distribution Water Quality, Flushing & Residual Management

15 Laboratory Testing & Sampling

15.1 Sampling, Preservation & Chain of Custody 15.2 Physical & Chemical Water Analysis 15.3 Wastewater Process Lab Testing 15.4 Microbiological Testing & QA/QC

16 Operator Math

16.1 Math Fundamentals, Conversions & Formula Sheets 16.2 Dosage, Chemical Feed & Detention Time 16.3 Flows, Loadings, Removal Efficiency & Solids Math 16.4 Pump Hydraulics & Horsepower

17 Safety, Security & Emergency Preparedness

17.1 Confined Space, LOTO, PPE & Chemical Safety 17.2 Chlorine Gas Safety & Emergency Response 17.3 Security, Hurricane Preparedness & Contingency Planning (Florida)

18 Equipment, O&M & Administration

18.1 Operate & Maintain Plant Equipment 18.2 Process Control Instrumentation & SCADA Basics 18.3 Records, Reporting & Administrative Duties

10.1 Secondary Process Fundamentals

Key Takeaways Explain This Topic AI

Secondary treatment biologically removes dissolved and colloidal organics after preliminary/primary steps by converting biodegradable BOD into settleable biomass and gases.

Activated sludge is a suspended-growth process pairing an aeration tank (mixed liquor) with a secondary clarifier that separates solids for RAS recycle and WAS wasting.

MLSS is total mixed-liquor solids; MLVSS better estimates active biomass; F/M relates organic load to microorganism mass under aeration.

SRT/MCRT is controlled mainly by WAS; RAS returns biomass and manages clarifier blankets but does not permanently remove solids from the system.

Classic secondary effluent framing is about ≤30 mg/L BOD and ≤30 mg/L TSS with roughly 85% removal; Florida permits, AWT, and reuse often require stricter quality.

Last updated: August 2026

10.1 Secondary Process Fundamentals

Quick Answer: Secondary treatment uses microorganisms to remove dissolved and colloidal organic matter after preliminary/primary steps. Activated sludge is a suspended-growth process: an aeration tank grows mixed liquor (MLSS/MLVSS) and a secondary clarifier separates solids; RAS returns biomass and WAS wastes excess. Control uses F/M , SRT/MCRT , DO, and settleability. Typical secondary effluent targets roughly ≤30 mg/L BOD and ≤30 mg/L TSS (classic 85% removal framework), with Florida plants often going further toward reuse or AWT.

Primary clarification removes settleable solids and some BOD, but most of the dissolved and fine colloidal organic load still remains. Secondary treatment is the biological engine that converts that biodegradable organic matter into settleable biomass, carbon dioxide, water, and residual solids. On FDEP wastewater Class C (and higher) exams, secondary process items test whether you understand what grows where , which solids inventories matter , and how wasting and recycle set sludge age —not architectural trivia about tank paint colors.

Goal of Secondary Treatment

Secondary treatment aims to:

Oxidize biodegradable organics measured as BOD (and related COD fractions).

Convert dissolved organics into biomass that can be settled and wasted.

Produce a clarified secondary effluent suitable for disinfection and disposal or further tertiary/AWT polishing.

Maintain a stable microbial culture under changing flow, load, temperature, and toxicity.

Federal secondary-treatment technology-based expectations historically framed municipal plants around roughly 85% BOD and TSS removal and effluent concentrations on the order of 30 mg/L BOD and 30 mg/L TSS (30-day averages in classic framing). Florida permits may be tighter—especially for surface discharge near sensitive waters, nutrient limits, or reclaimed water under FAC 62-610. For the exam: secondary is the biological organics/solids step; advanced nutrient and pathogen barriers are layered on top.

Suspended Growth vs Fixed Growth

Biological secondary processes fall into two broad families:

  • Feature Suspended growth (e.g., activated sludge) Fixed growth / fixed film (e.g., trickling filter, RBC)
  • Biomass location Free-floating flocs in mixed liquor Attached to media as biofilm
  • Solids control RAS/WAS and clarifier performance Sloughing rate, media wetting, underdrain flow

Mixing/aeration Mechanical mixers or diffused air in tank Air movement through media + optional forced ventilation

Shock load behavior Dilution in large MLSS inventory Biofilm layers can buffer short shocks

Common Florida use Package extended aeration, oxidation ditches, conventional AS Older TF plants, some RBCs, hybrid TF/AS

Suspended growth keeps microorganisms suspended in the liquid so every cell has access to substrate and oxygen if mixing and aeration are adequate. Fixed-film systems grow a biofilm on rock, plastic media, or rotating disks; wastewater flows past the film. Many modern plants are hybrids (e.g., TF followed by activated sludge polishing). Exam questions often ask which family a unit belongs to and which control knobs apply.

Activated Sludge Overview: Aeration Tank + Secondary Clarifier

The classic activated sludge flowsheet is deceptively simple:

Primary effluent (or raw after preliminary treatment at some package plants) enters the aeration tank .

Air or pure oxygen supplies dissolved oxygen (DO) while mixers keep mixed liquor suspended.

Mixed liquor flows to the secondary clarifier (final clarifier).

Settled sludge is split: Return Activated Sludge (RAS) recycles biomass to the aeration tank; Waste Activated Sludge (WAS) removes excess solids from the system.

Clarified secondary effluent goes to disinfection, filtration, reuse, or discharge.

Without a working clarifier, you do not have activated sludge—you have a dirty aeration tank. Without RAS, biomass washes out and MLSS collapses. Without WAS, solids accumulate until the clarifier is overloaded and effluent TSS rises.

Mixed Liquor and Solids Terminology

  • Term Meaning Why operators care
  • MLSS Mixed Liquor Suspended Solids (mg/L) Total solids inventory proxy in the aeration tank
  • MLVSS Mixed Liquor Volatile Suspended Solids (mg/L) Better proxy for active biomass (organic fraction of MLSS)
  • RAS Return Activated Sludge Returns settled biomass; sets recycle rate and clarifier blanket control
  • WAS Waste Activated Sludge Removes solids; primary control of SRT
  • SVI Sludge Volume Index Settleability indicator (mL/g)
  • F/M Food-to-Microorganism ratio Organic loading relative to biomass
  • SRT / MCRT Solids Retention Time / Mean Cell Residence Time Average time solids remain in the process

MLSS includes inert and organic suspended solids in the aeration basin. MLVSS is the volatile (mostly organic) portion and is preferred when estimating “bugs.” Typical conventional activated sludge MLSS might run roughly 1,500–3,500 mg/L , while extended aeration package plants often run higher (e.g., 3,000–6,000+ mg/L ranges are common textbook bands—always follow plant design and permit targets). Know the concept and relative ranges , not a single universal number.

Food-to-Microorganism Ratio (F/M)

F/M compares the organic food applied per day to the microorganism mass under aeration:

Food is typically mass of BOD (or COD) applied per day (lb/day or kg/day).

Microorganisms are typically mass of MLVSS (or MLSS) in the aeration tank(s).

High F/M means relatively more food and fewer bugs—growth is fast, sludge may be young, and effluent quality can suffer if the culture cannot keep up. Low F/M means older, more endogenous sludge typical of extended aeration —more complete oxidation, lower sludge production rate per BOD removed, but larger tank volume and aeration energy.

Exam framing:

  • Relative F/M Process character Typical association
  • Higher F/M Young sludge, rapid growth High-rate / conventional high-loaded modes
  • Moderate F/M Balanced growth and settling Conventional activated sludge
  • Low F/M Older sludge, endogenous respiration Extended aeration, many package plants

Operators rarely “set F/M” with a single dial; they waste (WAS) and manage MLSS inventory so F/M lands in the target band for the mode they run.

Solids Retention Time (SRT) / Mean Cell Residence Time (MCRT)

SRT (also called MCRT or sludge age) is the average time a solid particle remains in the activated sludge system. Conceptually:

SRT ≈ (total mass of solids in system) / (mass of solids leaving system per day)

Solids leave primarily in WAS and secondarily in effluent TSS . If you waste too little, SRT rises, sludge ages, endogenous decay increases, and you may see nitrification (if DO, alkalinity, and temperature allow) plus potential settling or foaming changes. If you waste too much, SRT falls, MLSS drops, treatment capacity falls, and pin floc or high effluent BOD can appear.

Key control relationship for exams:

WAS rate is the main long-term control of SRT and MLSS inventory.

RAS rate mainly manages clarifier solids and return of biomass—not a substitute for proper wasting.

Florida package extended aeration plants intentionally run long SRT (often on the order of 20–30+ days in textbook descriptions) for process simplicity and sludge stability. Conventional plants may run shorter SRT (often roughly 5–15 days depending on design and whether nitrification is required). Use plant-specific targets on the job; use relative long-vs-short reasoning on the exam.

  • RAS and WAS Roles
  • Return Activated Sludge (RAS)

RAS recycles settled biomass from the secondary clarifier underflow to the aeration tank inlet (or designated return point). Purposes:

Maintain desired MLSS inventory under aeration.

Control sludge blanket depth in the clarifier.

Provide continuous seed so the process does not wash out during hydraulic peaks.

RAS is often expressed as a percent of influent flow (e.g., 50–100% for many conventional systems; package plants vary). Too little RAS can raise the blanket and risk solids washout; too much RAS can dilute the aeration tank unnecessarily, increase clarifier hydraulic load from recycle, and mask wasting problems.

Waste Activated Sludge (WAS)

WAS removes solids from the system so net biomass growth does not accumulate forever. Wasting may be from the RAS line or from a separate WAS pump, depending on plant design. Consistent, measured wasting based on SRT or MLSS targets beats random “pull some sludge when it looks thick.”

Typical Effluent Quality After Secondary

After well-operated secondary treatment (before or after disinfection, depending on the sampling point):

  • Parameter Typical secondary expectation (classic framing) Notes for Florida exams
  • BOD5 On order of ≤30 mg/L (30-day concept) Permits may be tighter; AWT is much lower
  • TSS On order of ≤30 mg/L Clarifier and settleability drive TSS
  • Removal ~85% BOD/TSS historic secondary basis Industrial contributions change influent
  • Pathogens Reduced but not potable; need disinfection Secondary is not disinfection
  • Nutrients Partial; ammonia may drop if nitrifying Full N/P control is BNR/AWT territory

Secondary effluent is not finished water for unrestricted reuse without additional barriers. Florida reuse and AWT standards (see later chapters) build on secondary biology with filtration, higher disinfection, and nutrient limits.

How Secondary Fits the Full Plant Train

Think of the train as a story:

Preliminary — protect equipment (screens, grit).

Primary — settle what gravity can easily remove.

Secondary — biologically remove dissolved organics and convert to settleable biomass.

Tertiary / AWT / reuse — nutrients, filtration, advanced disinfection as required.

Solids handling — thicken, digest, dewater WAS and primary sludge.

If secondary fails, disinfection and disposal cannot fully compensate— high TSS and BOD will dominate effluent violations, chlorine demand will spike, and filters (if any) will blind.

Exam Anchors for Section 10.1

Memorize the goal of secondary (biological organics removal), suspended vs fixed growth , the aeration + clarifier pair, definitions of MLSS/MLVSS , F/M , SRT/MCRT , and the distinct roles of RAS vs WAS . Know that classic secondary effluent is framed around roughly 30/30 BOD/TSS and ~ 85% removal, while Florida permits and reuse often demand more. That cluster covers most “fundamentals of secondary” items before process-control and troubleshooting details.