Study guide
13.2 Calibration and Application-Rate Calculations
Georgia Commercial Pesticide Applicator Certification Exam Exam
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Exam Overview
1.1 Current Georgia Commercial Applicator Exam Facts 1.2 Private, Commercial, and Contractor Licenses 1.3 How to Prepare
2 Georgia and Federal Pesticide Law
2.1 Georgia Pesticide Use and Application Act of 1976 2.2 FIFRA, Registration, and Restricted-Use Classification 2.3 FQPA, ESA, WPS Overview, and Other Federal Rules
3 Certification, Categories, and Recertification
3.1 Exam Logistics, Scores, and Retakes 3.2 Georgia License Categories 21–41 3.3 Five-Year Recertification and Renewal Fees
4 Records, Contracting, and Landscape Posting
4.1 Georgia Recordkeeping (Rule 40-21-5) 4.2 Contractor Licenses and Financial Responsibility 4.3 Landscape Application Posting (Rule 40-21-9)
5 Pests, Control Methods, and IPM
5.1 Pest Recognition and Biology 5.2 Biological, Mechanical, Cultural, and Chemical Control 5.3 IPM Steps and Pesticide Resistance
6 Labels and Labeling Comprehension
6.1 The Label Is the Law; Registration Types 6.2 Label Parts, Signal Words, and Precautionary Statements 6.3 Directions for Use, REI, PHI, and SDS
7 Pesticide Types and Formulations
7.1 Solutions, Suspensions, Emulsions, and Liquid Formulations 7.2 Dry Formulations, Baits, Fumigants, and Packets 7.3 Adjuvants, Tank-Mix Compatibility, and Dilution
8 Toxicity, Exposure, and First Aid
8.1 Toxicity vs Hazard, LD50, and Toxicity Categories 8.2 Exposure Routes and Poisoning Symptoms 8.3 First Aid and Heat Stress vs Poisoning
9 PPE and Handler Safety
9.1 Chemical-Resistant Clothing, Gloves, Footwear, and Eyewear 9.2 Respirators and Fit 9.3 PPE Care, Wash, and Disposal
10 Pesticides in the Environment
10.1 Solubility, Adsorption, Persistence, and Volatility 10.2 Surface Water, Groundwater, Anti-Siphon, and Rule 40-23 10.3 Bees, Wildlife, Sensitive Sites, and Endangered Species
11 Transport, Storage, Security, and Disposal
11.1 Transportation and Site Security 11.2 Storage Site Design and Container Safety 11.3 Triple Rinse, Recycling, and Waste Disposal
12 Mixing, Loading, and Emergencies
12.1 Safe Mixing and Loading; Protecting Water 12.2 Closed Systems, Water-Soluble Packets, Enclosed Cabs 12.3 Spill Control-Contain-Clean and Fire Response
13 Equipment and Calibration
13.1 Sprayers, Nozzles, Granular, and Other Equipment 13.2 Calibration and Application-Rate Calculations 13.3 Area Math and Mixing Concentrates
14 Application Methods and Drift
14.1 Broadcast, Band, Directed, Spot, ULV, Chemigation 14.2 Particle vs Vapor Drift, Inversions, and Wind 14.3 Drift-Reduction Practices and Nozzle Selection
15 Supervision, WPS, and Professional Conduct
15.1 Supervising Uncertified Persons and Professional Conduct 15.2 Worker Protection Standard Duties 15.3 Paraquat and Other Product-Specific Training
16 Category Exam Competency
16.1 Categories 21, 22, 24 (Plant, Animal, Ornamental & Turf) 16.2 Categories 23, 25–27, 31, 41 (Forest, Seed, Aquatic, ROW, Public Health, Mosquito) 16.3 Categories 32–40 (Regulatory, Demo, Aerial, 35, Wood, Antimicrobial, Fumigation, Antifoulant, WPS)
13.2 Calibration and Application-Rate Calculations
Key Takeaways Explain This Topic AI
Boom sprayer formula: GPA = (GPM × 5940) ÷ (MPH × nozzle spacing in inches).
128 fluid ounces = 1 gallon; catch-test GPM = (ounces caught × 60) ÷ (128 × seconds).
Recalibrate after any nozzle, pressure, or speed change; a faster ground speed lowers GPA if GPM stays the same.
The labeled rate is the legal rate under FIFRA and the Georgia Pesticide Use and Application Act of 1976; calibration error is a common General Standards trap.
Granular calibration uses product collected over a measured swath width and travel distance, converted with 43,560 square feet per acre—not the 5940 liquid boom formula.
Last updated: August 2026
13.2 Calibration and Application-Rate Calculations
Calibration is how you prove the machine delivers the labeled rate . Rule 40-21-3-.01 General Standard 6 pairs equipment knowledge with calibration . National Core Appendix C is the math handbook: GPA, catch tests, the 128-ounce gallon , granular catch-over-distance, and mixing. Georgia will not hand you a formula sheet at a technical-college sitting on gapestexam.com. You must own the arithmetic.
Two legal facts sit under every number. First, the label rate is the law . FIFRA and the Georgia Pesticide Use and Application Act of 1976 both treat use contrary to labeling as a violation. Second, calibration error is a common exam trap : candidates mix perfectly while the boom is applying 14 GPA instead of the 20 GPA they used in the mixing formula, so every acre is overdosed or starved. Passing the calculator step is not enough if you skip the catch test.
The boom formula you must memorize
For a boom sprayer with equally spaced nozzles:
- GPA = (GPM × 5940) ÷ (MPH × nozzle spacing in inches)
- GPA = gallons per acre of spray mixture
- GPM = gallons per minute from one nozzle (or the average of several)
- 5940 = the unit-conversion constant that turns gallons/minute, miles/hour, and inches into gallons/acre
- MPH = travel speed in miles per hour
- Nozzle spacing = inches between nozzles on the boom (not automatically the cotton row width)
Where 5940 comes from, so you are not memorizing a magic number: acres per minute = (MPH × 88 feet per minute × spacing in feet) ÷ 43,560. Spacing in feet is inches ÷ 12. Rearrangement yields GPA = GPM × 5940 ÷ (MPH × inches) .
If you band, use the band width in inches when the formula is set up for band GPA, or convert broadcast GPA to a band fraction. For this chapter’s broadcast peanut and cotton examples, spacing is the nozzle spacing on the boom .
Rearranged, GPM = (GPA × MPH × spacing) ÷ 5940 , which is how you select a catalog tip after you choose a GPA and a speed.
Catch test and 128 ounces = 1 gallon
A catch test times how many fluid ounces one nozzle delivers into a measuring cup while the sprayer runs at field pressure and tank agitation. Because 128 fluid ounces = 1 gallon :
GPM = (ounces caught × 60) ÷ (128 × seconds)
The 60 converts minutes. The 128 converts ounces to gallons. Catch several nozzles along the boom, average the ounces, then convert. Replace any nozzle that is more than about 10 percent off the set average or off catalog (Chapter 11 wear rule from 13.1).
Field procedure that Appendix C expects you to describe:
Fill the tank with clean water (or the carrier you will actually spray if the manual requires it).
Set pressure at the boom , using a working gauge.
Select the gear and RPM you will use in the peanut or cotton field—not an idle “calibration speed.”
Catch each sampled nozzle for the same number of seconds.
Convert average ounces to GPM, then GPM to GPA.
Time travel speed on a measured course. One reliable check: 88 feet in 10 seconds is 6 MPH , because 1 MPH is 88 feet per minute.
1/128-acre shortcut: 43,560 ÷ 128 = 340.3 square feet . Course length in feet ≈ 4084 ÷ nozzle spacing in inches . Time a nozzle catch while you travel that course at field speed. Ounces collected ≈ GPA . That works because ounces per 1/128 acre equal gallons per acre.
- Nozzle spacing (inches) 1/128-acre course length (feet)
- 18 227
- 20 204
- 30 136
- 40 102
- Full Georgia peanut and cotton worked example
A commercial applicator in Dooly County will broadcast a foliar fungicide on peanuts , then use the same boom layout on cotton later in the week. Setup:
- Nozzle spacing W = 18 inches
- Field speed 6 MPH (88-foot course timed at 10 seconds)
- Catch test on a representative nozzle: 16 fluid ounces in 25 seconds at the pressure you will use in the field
- Step 1 — convert the catch to GPM
- GPM = (16 × 60) ÷ (128 × 25)
- GPM = 960 ÷ 3200
- GPM = 0.30 gallons per minute per nozzle
- Step 2 — convert GPM to GPA with the boom formula
- GPA = (0.30 × 5940) ÷ (6 × 18)
- GPA = 1782 ÷ 108
- GPA = 16.5 gallons per acre
- Step 3 — check the label
If the peanut fungicide label requires 15–20 GPA by ground, 16.5 GPA is inside the legal window. If the label said “minimum 20 GPA by ground,” 16.5 GPA would be illegal even though the arithmetic is perfect. Slow down, install a higher-flow tip, or—only within the nozzle’s rating—adjust pressure, then recalibrate . Do not “guess it up to 20.”
Cotton check on the same boom. Same 0.30 GPM and 18-inch spacing, but the operator speeds up to 8 MPH to finish before an afternoon thunderstorm:
GPA = (0.30 × 5940) ÷ (8 × 18) = 1782 ÷ 144 = 12.4 GPA
If the cotton insecticide label still wants 15–20 GPA, 12.4 GPA fails. Speed diluted the volume. That is why National Core says recalibrate after a speed change , not only after a nozzle change. Mixing 13.3’s tank formula with yesterday’s 16.5 GPA while actually spraying 12.4 GPA under-applies product per acre—or, if you keep dumping the same tank on fewer acres because you empty sooner, you scramble the rate. Measure; do not assume.
Pressure change. Flow through a nozzle varies approximately with the square root of pressure . Roughly, to double GPM you need about four times the pressure—often impossible without ruining droplet size. If you bump 40 psi to 50 psi, GPM rises only about √(50/40) = √1.25 ≈ 1.12 , a 12 percent flow increase, and droplets get finer (more drift). Treat a pressure change as a new calibration, then confirm droplet quality still matches the label’s drift language.
Recalibrate after nozzle, pressure, or speed changes
Recalibrate when you:
- Replace nozzles or change nozzle type (tapered flat fan to air-induction, 11002 to 11003)
- Change operating pressure
- Change travel speed or the gear/RPM that sets speed
- Change spray specific gravity substantially (heavy fertilizer solutions versus water)
- See streaking, foam, or a pressure gauge that no longer matches a catch test
Water is the usual calibration liquid. Fertilizer carriers and some oils flow differently; follow the equipment manual and the label. After recalibration, rebuild the mix using the new GPA (section 13.3). Leaving yesterday’s pints in the tank after today’s speed change is how a legal label rate becomes an illegal field rate.
Granular: amount per swath distance
Granules do not use the 5940 boom formula. You measure product collected over a known swath width and travel distance , then convert to pounds (or ounces) per acre.
- Pounds that should be collected = (labeled lb/acre × swath width in feet × distance in feet) ÷ 43,560
- Worked granular example — peanut soil insecticide, Tift County
Label rate 10 lb/acre . Rotary spreader effective swath 20 feet . You drive 217.8 feet so the strip is 20 × 217.8 = 4,356 sq ft = 0.10 acre (because 43,560 × 0.10 = 4,356).
Amount that should land on a catch tarp covering that swath and distance:
10 lb/acre × 0.10 acre = 1.0 lb of granules
If pans collect 1.3 lb, you are about 30 percent hot. Slow the spinner, close the gate, or change speed, then repeat. If pans collect 0.7 lb, you are starving the labeled rate.
Shorter field run: 20 ft × 200 ft = 4,000 sq ft = 4,000 ÷ 43,560 = 0.0918 acre ; at 10 lb/acre collect 0.918 lb (about 14.7 ounces of product). Same formula, less convenient numbers—do not round 0.918 lb up to 2 lb “for good measure.” Extra granules are still extra product per acre.
Speed timing reminder: seconds = distance in feet ÷ (MPH × 1.467) . Calibration is a measured catch plus a measured speed, not a tractor speedometer wish. Then mix to the GPA or lb/acre you actually measured, because the label rate is still the law .