Study guide

8.3 Physical Hazards and Detection Controls

HACCP Certification Hazard Analysis Critical Control Points

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Overview

1.1 Current Exam Facts & Logistics 1.2 What Is HACCP? History, Codex, and Purpose 1.3 Core HACCP Definitions

2 HACCP System Foundation

2.1 Preventive HACCP vs Traditional Inspection 2.2 Management Commitment, Culture, and Training 2.3 Where HACCP Applies: Sectors and Supply Chain

3 Preliminary Steps: Team, Product, and Consumers

3.1 Assemble the HACCP Team 3.2 Describe the Food and Its Distribution 3.3 Intended Use and Consumers of the Food

4 Preliminary Steps: Flow Diagrams

4.1 Construct a Process Flow Diagram 4.2 On-Site Verification of the Flow Diagram

5 Principle 1: Conduct a Hazard Analysis

5.1 Hazard Analysis: Identification and Evaluation 5.2 Control Measures and Hazard Analysis Worksheets 5.3 Biological Hazards Overview and Growth Factors

6 Biological Pathogens: Salmonella, Listeria, and STEC

6.1 Salmonella and Campylobacter 6.2 Listeria monocytogenes 6.3 E. coli O157:H7 and Other STEC

7 Biological Pathogens: Clostridia, Staph, Bacillus, Viruses, Parasites

7.1 Clostridium botulinum and Clostridium perfringens 7.2 Staphylococcus aureus and Bacillus cereus 7.3 Norovirus, Hepatitis A, and Parasites

8 Chemical Hazards, Allergens, and Physical Hazards

8.1 Chemical Hazards and Natural Toxins 8.2 Food Allergens as Chemical Hazards 8.3 Physical Hazards and Detection Controls

9 Principles 2–3: CCPs and Critical Limits

9.1 Principle 2: Identify Critical Control Points 9.2 The CCP Decision Tree 9.3 Principle 3: Establish Critical Limits

10 Principles 4–5: Monitoring and Corrective Actions

10.1 Principle 4: Establish Monitoring Procedures 10.2 Continuous vs Discontinuous Monitoring and Responsibilities 10.3 Principle 5: Establish Corrective Actions

11 Principles 6–7: Verification and Record-Keeping

11.1 Principle 6: Establish Verification Procedures 11.2 Validation vs Verification 11.3 Principle 7: Record-Keeping and Documentation

12 Prerequisite Programs: Foundation, GMPs, and Sanitation

12.1 Prerequisite Programs as the HACCP Foundation 12.2 Current Good Manufacturing Practices (cGMPs) 12.3 SSOPs, Cleaning, and Sanitation

13 Prerequisite Programs: Hygiene, Suppliers, Allergens, and Traceability

13.1 Personal Hygiene, Employee Health, and Pest Control 13.2 Supplier Control, Receiving, Storage, and Shipping 13.3 Allergen Control, Traceability, Chemical Control, and Water

14 HACCP Plans and Regulatory Framework

14.1 Building the Written HACCP Plan 14.2 FDA and USDA Mandatory HACCP Programs 14.3 FSMA, HARPC, and Modern Food Safety Systems

15 Implementation, Critical Numbers, and Exam Strategy

15.1 Implementation, Maintenance, and Revalidation 15.2 Critical Temperatures and Numbers Review 15.3 Exam Traps, Scenarios, and Study Plan

8.3 Physical Hazards and Detection Controls

Key Takeaways Explain This Topic AI

Physical hazards are foreign objects that can injure consumers—metal, glass, hard plastic, wood, bone, stones, and similar materials.

Sources include raw materials, equipment wear, packaging, poor employee practices, and facility fabric (lights, windows, tools).

Detection and removal controls include magnets, metal detectors, X-ray systems, filters, screens, sieves, bone collection, and glass-breakage policies.

Inline metal detection or X-ray after the last contamination likely point is often a CCP; many source-prevention measures remain PRPs.

Glass policies, captive tools, preventive maintenance, and supplier controls reduce likelihood so detectors are not the only line of defense.

Last updated: July 2026

8.3 Physical Hazards and Detection Controls

Quick Answer: Physical hazards are foreign objects — metal, glass, hard plastic, wood, bone, stones, and similar materials—that can injure consumers (cuts, choking, dental damage). Control combines prevention (maintenance, glass policy, supplier specs, employee practices) with detection/removal ( magnets, metal detectors, X-ray, filters, screens ). When a detector is the essential step that reduces a significant physical hazard before shipment, it is often a CCP ; source control is usually a PRP .

Physical hazards complete the hazard triad with biological and chemical risks. Exam questions focus on object types , where they enter , which device finds them , and CCP vs PRP logic.

Common Physical Hazards

Hazard Typical sources Injury concern

Metal Bolts, wire, screen wire, blades, wear from grinders/mixers, staples, equipment shavings Laceration, dental injury

  • Glass Light fixtures, gauges, bottles, jar breakage, lab glass Cuts, embedded fragments
  • Hard plastic / rubber Scraper blades, tote fragments, glove pieces, brittle container chips Choking, injury
  • Wood Pallets, brooms, stirrers (discouraged), crates Splinters, injury
  • Bone Meat/poultry raw materials, incomplete bone collection Dental injury, choking
  • Stones / grit Field crops, root vegetables, poor dry cleaning of commodities Dental injury
  • Other Jewelry, pens, paper clips, phone parts (GMPs) Variable

Soft materials that dissolve or are not injurious may be quality issues rather than safety hazards—hazard evaluation must be honest about severity (size, hardness, sharpness).

Where Physical Hazards Enter the Process

Incoming materials — metal in ingredients, stones in grains/produce, bone in meat, glass from supplier packaging.

Processing equipment — failing screens, broken mixer paddles, chain links, cutter blades.

Packaging — glass jar breakage, plastic shavings from conveyors, metal clips.

People and tools — unsecured jewelry, improper tools above open product.

Facility fabric — unprotected lights, windows, flaking structures (also chemical/foreign-matter).

Flow diagrams should mark steps where introduction is reasonably likely so controls can be placed after the last likely introduction when detection is used.

  • Prevention Controls (Mostly PRPs)
  • Hygienic design and maintenance
  • Preventive maintenance and inspection of wear parts
  • Prompt repair of damaged screens, belts, and paddles
  • Captive tool programs; no glass thermometers in open-product areas when alternatives exist
  • Glass and brittle plastic policy

A written glass policy typically includes:

  • Inventory of glass and brittle plastic in production areas
  • Protected lighting (sleeved/shatter-resistant)
  • Exclusion of unnecessary glass

Breakage procedure : stop line, contain area, clean up with dedicated tools, dispose of potentially contaminated product, inspect, document, management release

  • Supplier and receiving
  • Specifications limiting foreign material
  • Sieving or inspection of high-risk commodities at receiving when justified
  • Bone collection and supplier programs for meat
  • Personnel GMPs
  • No jewelry (per policy), secure pens, appropriate gloves, no loose objects above product

These measures reduce likelihood . They often remain prerequisite programs even when excellent.

  • Detection and Removal Technologies
  • Magnets

Magnets capture ferrous (and some magnetic stainless, depending on design) metal from dry free-flowing products or liquid lines. They are useful upstream protection and as part of layered defense. Limitations: poor for non-magnetic stainless and non-metal hazards. Magnets require scheduled inspection and cleaning; a full magnet may stop capturing.

Metal detectors

Metal detectors sense conductive metal (ferrous, non-ferrous, and many stainless types depending on calibration and product effect). Common at end of line or after final processing. Critical program elements:

  • Sensitivity standards (test pieces) for Fe, non-Fe, and stainless as applicable
  • Calibration / challenge testing at defined frequency
  • Reject mechanism that reliably removes product (belt stop, air blast, reject arm)
  • Locked reject bin and controlled disposition
  • Product effect compensation for wet/salty products
  • X-ray inspection

X-ray systems detect density differences—often metal, glass, stone, bone, and some hard plastics that metal detectors miss. Useful for glass-in-jar, bone-in-meat, and multi-pack formats. Still requires validation of what size/type of object can be detected in the specific product matrix.

Filters, screens, and sieves

Filters and screens remove foreign material from liquids and powders. A broken screen can become a metal-wire hazard itself—inspect integrity. Sieves at intake of flour, sugar, or spices are classic PRPs or process controls.

  • Other
  • Bone collectors / soft tissue separators in meat
  • Visual sorting (limited reliability alone for high-speed lines)
  • Optical sorters in some produce/nut operations
  • When Physical Detection Is a CCP vs. a PRP

Use Principle 2 decision-tree thinking:

Often a CCP when:

  • The physical hazard is significant (reasonably likely and severe if uncontrolled), and
  • The detection/rejection step is essential to reduce the hazard to an acceptable level, and
  • No later step will reliably remove the hazard, and

The step has a measurable critical limit (e.g., detector must reject a 1.5 mm ferrous test sphere; continuous operation with functioning reject).

Classic example: Finished-product metal detector or X-ray after the last point where metal can enter, with defined test-piece limits, monitoring, and corrective actions (hold all product since last good check, retest, repair, disposition).

Often a PRP when:

  • The measure is general prevention (glass policy, maintenance, jewelry GMP, supplier foreign-material program)
  • Magnets or sieves are supportive layers but not the designated essential control

Likelihood is controlled so low that residual risk is managed without a process CCP (still document the analysis)

Exam trap: Calling every magnet a CCP automatically—or calling a final metal detector “only a PRP” when it is the plant’s essential metal control. Decision tree + significance drive the answer, not the brand of equipment.

  • Monitoring and corrective action for a detector CCP
  • Challenge with certified test pieces at start-up, breaks, and defined intervals

If a challenge fails: stop , segregate product back to last successful check, repair/recalibrate, retest, disposition affected lots

  • Never bypass a reject device without QA authorization and alternate controls
  • Integrating Physical Hazards into Hazard Analysis

List potential objects by step (grind → metal from plates; jar fill → glass; harvest receive → stones).

Evaluate severity (hard/sharp objects above a size threshold).

Assign prevention PRPs + detection CCPs where essential.

Validate detector capability on your product (product effect, packaging).

Record challenges, rejects, and maintenance.

Exam Application Scenarios

Bolt missing from a mixer after sanitation: physical metal hazard → find bolt or detect/reject product; maintenance PRP failed; metal detector may protect consumers if downstream.

Glass bottle line breakage: execute glass policy; quarantine product in zone; do not “sort by eye only” without procedure.

Stone in dried beans: supplier + sieving; X-ray or optical sort where used; cook does not remove stones.

Metal detector CCP: critical limit = successful detection/rejection of specified test pieces; monitoring = documented challenges; corrective action = hold and re-inspect since last good test.

Comparison Snapshot (Ch 8 Close)

  • Hazard class Example Typical essential control style
  • Chemical – residue Sanitizer Chemical PRP / SSOP
  • Chemical – toxin Histamine, aflatoxin Cold chain / supplier & testing
  • Chemical – allergen Undeclared peanut Label + sanitation + scheduling
  • Physical Metal fragment Detector CCP + maintenance PRP

Physical hazards reward layered defense : keep objects out, then find what still got in . With chemical, allergen, and physical controls in place, the plan is ready for CCP identification and critical limits in the next chapter block of principles.