Study guide
6.1 Reactance, Impedance, Resonance & Quality Factor (Q)
FCC Amateur Radio General License Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Introduction & Exam Strategy
1.1 General Class License Overview, Exam Format & Question Pool Structure 1.2 Core Study Strategies, Formula Quick Reference & Test-Taking Tactics
2 Chapter 2: Subelement G1 – Commission's Rules
2.1 General Class Band Privileges & ITU Regions 2.2 Antenna Structure Limits, Beacons & Security Rules 2.3 Transmitter Power Limits, 60-Meter Band Rules & Prohibited Transmissions 2.4 Volunteer Examiner Accreditation, Exam Administration & Remote Testing 2.5 Control Operator Categories, Repeaters, Third-Party Traffic & Station Identification
3 Chapter 3: Subelement G2 – Operating Procedures
3.1 HF Phone Operating Procedures, SSB Tuning & Phonetic Alphabet 3.2 CW Operating Procedures, Q-Signals, RIT/XIT & Split Operation 3.3 Digital Operating Procedures: FT8, JS8Call, PSK31 & RTTY 3.4 Emergency Communications, Traffic Nets, RACES, ARES & Distress Priority 3.5 Volunteer Monitor Program, HF Direction Finding & Azimuthal Maps
4 Chapter 4: Subelement G3 – Radio Wave Propagation
4.1 Solar Activity, Sunspots, Solar Flux Index & Geomagnetic Indices 4.2 Maximum Usable Frequency (MUF), Lowest Usable Frequency (LUF) & Ionospheric Layers 4.3 Skywave Propagation, NVIS, HF Scatter & Tropospheric Ducting
5 Chapter 5: Subelement G4 – Amateur Radio Practices
5.1 Station Setup, Speech Processors & Audio DSP Filters 5.2 Test Equipment: RF Wattmeters, SWR Bridges, Dummy Loads & Oscilloscopes 5.3 Radio Frequency Interference (RFI), TVI, Harmonics & Core Filtering 5.4 Station Grounding, Bonding & Lightning Protection 5.5 Mobile and Portable HF Operations, Vehicle Noise & Battery Systems
6 Chapter 6: Subelement G5 – Electrical Principles
6.1 Reactance, Impedance, Resonance & Quality Factor (Q) 6.2 Decibels, Power Calculations & RMS/Peak AC Voltage Conversions 6.3 Power Factor, Transformer Ratios & Resistive Voltage Dividers
7 Chapter 7: Subelement G6 – Circuit Components
7.1 Inductors, Toroid Cores, Crystals & Semiconductor Diodes 7.2 Transistors (BJT, FET), Voltage Regulators & Vacuum Tube Amplifiers
8 Chapter 8: Subelement G7 – Practical Circuits
8.1 Linear Power Supplies, Rectifier Circuits & Filter Capacitors 8.2 RF Filters, Oscillators (Colpitts, Hartley, Pierce) & Mixers 8.3 Superheterodyne Receivers, Direct Sampling SDRs & Transceiver Architecture
9 Chapter 9: Subelement G8 – Signals and Emissions
9.1 SSB, CW, AM & FM Modulation Principles & Carrier Suppression 9.2 Frequency Mixing, Intermodulation Distortion (IMD) & Bandwidth Standards 9.3 Digital Emission Protocols, Baudot, PSK, FSK & Symbol Rates
10 Chapter 10: Subelement G9 – Antennas and Feed Lines
10.1 Half-Wave Dipoles, Quarter-Wave Verticals & Radiation Patterns 10.2 Directional Antennas: Yagi-Uda, Cubical Quad & Phased Arrays 10.3 Transmission Lines, Characteristic Impedance, Attenuation & SWR 10.4 Antenna Tuners, Impedance Matching Networks & Baluns
11 Chapter 11: Subelement G0 – Electrical and RF Safety
11.1 RF Exposure Evaluation, Maximum Permissible Exposure (MPE) & Safety Offsets 11.2 Tower Safety, Fall Arrest Gear, Antenna Installation & AC Power Hazards
6.1 Reactance, Impedance, Resonance & Quality Factor (Q)
Key Takeaways Explain This Topic AI
Inductive reactance (X_L = 2πfL) increases linearly with frequency and inductance, causing alternating current to lag alternating voltage by exactly 90 degrees (+90° phase lead of voltage).
Capacitive reactance (X_C = 1 / (2πfC)) decreases inversely with frequency and capacitance, causing alternating current to lead alternating voltage by exactly 90 degrees (-90° phase lag of voltage).
Total series impedance is the vector sum of resistance and net reactance: Z = √(R² + (X_L - X_C)²); when inductive and capacitive reactances are equal, net reactance is zero and the circuit is purely resistive (Z = R).
At electrical resonance (X_L = X_C), a series RLC circuit exhibits minimum impedance (equal to R) and maximum current, whereas a parallel RLC tank circuit exhibits maximum impedance and minimum external line current.
The Quality Factor (Q = X_L / R = f₀ / Bandwidth) quantifies resonant circuit sharpness and energy efficiency; higher Q results in narrower half-power (-3 dB) bandwidth and steeper filter selectivity.
Last updated: August 2026
6.1 Reactance, Impedance, Resonance & Quality Factor (Q)
In direct current (DC) circuits, electrical resistance ( R R R ) is the sole property that opposes the flow of electric charge, governed strictly by Ohm's Law ( V = I ⋅ R V = I \cdot R V = I ⋅ R ). In alternating current (AC) and radio frequency (RF) circuits, however, current and voltage fluctuate continuously in magnitude and reverse direction periodically. This continuous oscillation introduces time-dependent electromagnetic phenomena where energy is cyclically stored in and released from magnetic and electric fields. The opposition to AC current flow arising from this stored energy is called reactance ( X X X ), and the total opposition resulting from the combination of resistance and reactance is known as impedance ( Z Z Z ).
Mastering reactance, impedance, resonance, and the Quality Factor ( Q Q Q ) is fundamental to amateur radio. These principles govern the operation of antenna matching networks, intermediate frequency (IF) filters, transmitter output tank circuits, transmission line stubs, and RF oscillators.
1. Inductive & Capacitive Reactance
Reactance represents the opposition that an inductive or capacitive circuit component presents to alternating current. Unlike pure resistance—which permanently dissipates electrical energy as heat—pure reactance stores energy temporarily during one quarter of the AC cycle and returns it to the source during the subsequent quarter cycle, consuming zero net average power . +-----------------------------------------------------------------------------------------+
- | REACTANCE & PHASE RELATIONSHIP SUMMARY |
- | |
- | Component Symbol Formula Frequency Trend Phase Relationship |
- | --------------------------------------------------------------------------------------- |
- | Inductor X_L X_L = 2 * π * f * L Increases (f ↑) Voltage LEADS Current |
- | by 90° (+90° phase) |
- | Capacitor X_C X_C = 1 / (2 * π * f * C) Decreases (f ↑) Current LEADS Voltage |
- | by 90° (-90° phase) |
- +-----------------------------------------------------------------------------------------+
- Inductive Reactance ( X L X_L X L )
When an alternating current flows through an inductor (a coil of wire), the changing magnetic flux induces a counter-electromotive force (back-EMF) that opposes changes in current, in accordance with Lenz's Law. This opposition is inductive reactance ( X L X_L X L ). X L = 2 π f L X_L = 2\pi f L X L = 2 π f L
Where:
- X L X_L X L is inductive reactance in ohms ( Ω \Omega Ω )
- f f f is frequency in Hertz (Hz)
- L L L is inductance in Henrys (H)
- π ≈ 3.14159 \pi \approx 3.14159 π ≈ 3.14159
Key Characteristics of Inductive Reactance:
Direct Proportionality: X L X_L X L is directly proportional to both frequency and inductance. Doubling the operating frequency or doubling the inductance doubles the inductive reactance.
Phase Relationship (Voltage Leads Current): Because the back-EMF opposes current buildup, current cannot change instantaneously. In an ideal inductor, the voltage wave leads the current wave by 90 degrees (a phase angle of + 90 ∘ +90^\circ + 9 0 ∘ ).
DC Behavior: At DC ( f = 0 Hz f = 0\text{ Hz} f = 0 Hz ), X L = 0 Ω X_L = 0\,\Omega X L = 0 Ω . An ideal inductor acts as a dead short circuit to direct current.
Capacitive Reactance ( X C X_C X C )
A capacitor consists of two conductive plates separated by an insulating dielectric. As alternating voltage is applied, charge accumulates on the plates until the electrostatic field voltage opposes the applied voltage. This opposition is capacitive reactance ( X C X_C X C ). X C = 1 2 π f C X_C = \frac{1}{2\pi f C} X C = 2 π f C 1
Where:
- X C X_C X C is capacitive reactance in ohms ( Ω \Omega Ω )
- f f f is frequency in Hertz (Hz)
- C C C is capacitance in Farads (F)
Key Characteristics of Capacitive Reactance:
Inverse Proportionality: X C X_C X C is inversely proportional to both frequency and capacitance. Doubling the frequency or doubling the capacitance cuts the capacitive reactance in half .
Phase Relationship (Current Leads Voltage): Current flows at its maximum when the capacitor plates are uncharged (zero voltage). As charge accumulates and voltage reaches its peak, current drops to zero. Thus, in an ideal capacitor, the current wave leads the voltage wave by 90 degrees (voltage lags current by 90 degrees, a phase angle of − 90 ∘ -90^\circ − 9 0 ∘ ).
DC Behavior: At DC ( f = 0 Hz f = 0\text{ Hz} f = 0 Hz ), X C = ∞ Ω X_C = \infty\,\Omega X C = ∞ Ω . An ideal capacitor completely blocks direct current, acting as an open circuit.
- Tip
- The Classic Mnemonic: "ELI the ICE man"
ELI: In an Inductor ( L ), Voltage ( E , electromotive force) leads Current ( I ).
ICE: In a Capacitor ( C ), Current ( I ) leads Voltage ( E ).
Worked Example: Reactance Calculations at HF
Problem 1: Calculate the inductive reactance of a 10 μ H 10\,\mu\text{H} 10 μ H ( 10 × 10 − 6 H 10 \times 10^{-6}\text{ H} 10 × 1 0 − 6 H ) inductor at 14.15 MHz 14.15\text{ MHz} 14.15 MHz ( 14.15 × 10 6 Hz 14.15 \times 10^6\text{ Hz} 14.15 × 1 0 6 Hz ). X L = 2 π f L = 2 × 3.14159 × ( 14.15 × 10 6 ) × ( 10 × 10 − 6 ) = 2 × 3.14159 × 141.5 ≈ 889.1 Ω X_L = 2\pi f L = 2 \times 3.14159 \times (14.15 \times 10^6) \times (10 \times 10^{-6}) = 2 \times 3.14159 \times 141.5 \approx 889.1\,\Omega X L = 2 π f L = 2 × 3.14159 × ( 14.15 × 1 0 6 ) × ( 10 × 1 0 − 6 ) = 2 × 3.14159 × 141.5 ≈ 889.1 Ω
Problem 2: Calculate the capacitive reactance of a 100 pF 100\text{ pF} 100 pF ( 100 × 10 − 12 F 100 \times 10^{-12}\text{ F} 100 × 1 0 − 12 F ) capacitor at 14.15 MHz 14.15\text{ MHz} 14.15 MHz . X C = 1 2 π f C = 1 2 × 3.14159 × ( 14.15 × 10 6 ) × ( 100 × 10 − 12 ) = 1 0.008891 ≈ 112.5 Ω X_C = \frac{1}{2\pi f C} = \frac{1}{2 \times 3.14159 \times (14.15 \times 10^6) \times (100 \times 10^{-12})} = \frac{1}{0.008891} \approx 112.5\,\Omega X C = 2 π f C 1 = 2 × 3.14159 × ( 14.15 × 1 0 6 ) × ( 100 × 1 0 − 12 ) 1 = 0.008891 1 ≈ 112.5 Ω
2. Complex Impedance ( Z Z Z ) in Series AC Circuits
When resistance, inductance, and capacitance coexist in a single series circuit, the total opposition to alternating current is called impedance ( Z Z Z ). Because the voltages across resistors, inductors, and capacitors are out of phase with each other, their oppositions cannot simply be added algebraically. Instead, they must be combined as orthogonal vectors (phasors) in the complex impedance plane. +j (Inductive Reactance: +X_L)
- ^
- | * Impedance Vector (Z)
- | / |
- | / |
- | / | Net Reactance
- | / | (X = X_L - X_C)
- | / θ |
- (Purely Resistive) 0 --------+--/------+--------> +R (Resistance)
- | \ |
- | \ |
- | \ |
- | \ |
- | \ |
- | v |
- v
- j (Capacitive Reactance: -X_C)
- The Mathematical Formulas for Series Impedance
In a series RLC circuit, net reactance ( X X X ) is the algebraic difference between inductive reactance and capacitive reactance: X = X L − X C X = X_L - X_C X = X L − X C
Total impedance magnitude ( ∣ Z ∣ |Z| ∣ Z ∣ ) is calculated using the Pythagorean theorem: Z = R 2 + X 2 = R 2 + ( X L − X C ) 2 Z = \sqrt{R^2 + X^2} = \sqrt{R^2 + (X_L - X_C)^2} Z = R 2 + X 2 = R 2 + ( X L − X C ) 2
The phase angle ( θ \theta θ ) between the applied total voltage and circuit current is: θ = arctan ( X L − X C R ) = arctan ( X R ) \theta = \arctan\left(\frac{X_L - X_C}{R}\right) = \arctan\left(\frac{X}{R}\right) θ = arctan ( R X L − X C ) = arctan ( R X )
Circuit Behavioral States
Inductive Circuit ( X L > X C X_L > X_C X L > X C ): The net reactance is positive ( + j X +jX + j X ). Total voltage leads current by phase angle θ \theta θ ( 0 ∘ < θ < 90 ∘ 0^\circ < \theta < 90^\circ 0 ∘ < θ < 9 0 ∘ ).
Capacitive Circuit ( X C > X L X_C > X_L X C > X L ): The net reactance is negative ( − j X -jX − j X ). Total current leads voltage by phase angle θ \theta θ ( − 90 ∘ < θ < 0 ∘ -90^\circ < \theta < 0^\circ − 9 0 ∘ < θ < 0 ∘ ).
Resistive / Resonant Circuit ( X L = X C X_L = X_C X L = X C ): Net reactance is zero ( X = 0 X = 0 X = 0 ). Impedance equals pure resistance ( Z = R Z = R Z = R ), and phase angle is exactly 0 ∘ 0^\circ 0 ∘ .
Step-by-Step Worked Example: Series RLC Circuit
Problem: A series circuit contains a 30 Ω 30\,\Omega 30 Ω non-inductive resistor, an inductor with X L = 80 Ω X_L = 80\,\Omega X L = 80 Ω , and a capacitor with X C = 40 Ω X_C = 40\,\Omega X C = 40 Ω . What is the total impedance and phase angle?
Calculate net reactance: X = X L − X C = 80 Ω − 40 Ω = + 40 Ω X = X_L - X_C = 80\,\Omega - 40\,\Omega = +40\,\Omega X = X L − X C = 80 Ω − 40 Ω = + 40 Ω (inductive).
Calculate total impedance magnitude: Z = R 2 + X 2 = 30 2 + 40 2 = 900 + 1600 = 2500 = 50 Ω Z = \sqrt{R^2 + X^2} = \sqrt{30^2 + 40^2} = \sqrt{900 + 1600} = \sqrt{2500} = 50\,\Omega Z = R 2 + X 2 = 3 0 2 + 4 0 2 = 900 + 1600 = 2500 = 50 Ω
Calculate phase angle: θ = arctan ( 40 30 ) = arctan ( 1.333 ) ≈ + 53.13 ∘ \theta = \arctan\left(\frac{40}{30}\right) = \arctan(1.333) \approx +53.13^\circ θ = arctan ( 30 40 ) = arctan ( 1.333 ) ≈ + 53.1 3 ∘ The circuit presents an impedance of 50 Ω 50\,\Omega 50 Ω with voltage leading current by 53.13 ∘ 53.13^\circ 53.1 3 ∘ .
3. Electrical Resonance: Series vs. Parallel Resonant Circuits
Resonance occurs in an AC circuit containing both inductance and capacitance at the exact frequency where inductive reactance equals capacitive reactance ( X L = X C X_L = X_C X L = X C ). Setting the two reactance equations equal reveals the fundamental resonant frequency formula ( f 0 f_0 f 0 ): 2 π f 0 L = 1 2 π f 0 C ⟹ f 0 2 = 1 4 π 2 L C ⟹ f 0 = 1 2 π L C 2\pi f_0 L = \frac{1}{2\pi f_0 C} \implies f_0^2 = \frac{1}{4\pi^2 L C} \implies f_0 = \frac{1}{2\pi\sqrt{LC}} 2 π f 0 L = 2 π f 0 C 1 ⟹ f 0 2 = 4 π 2 L C 1 ⟹ f 0 = 2 π L C 1
Where f 0 f_0 f 0 is resonant frequency in Hertz, L L L is inductance in Henrys, and C C C is capacitance in Farads. +-----------------------------------------------------------------------------------------+
- | SERIES RESONANCE VS. PARALLEL RESONANCE COMPARISON |
- | |
- | Characteristic Series Resonant Circuit Parallel Resonant Circuit (Tank) |
- | --------------------------------------------------------------------------------------- |
- | Reactance Balance X_L = X_C X_L = X_C |
- | Net Reactance (X) Zero (0 Ω) Zero (0 Ω) |
- | Terminal Impedance MINIMUM (Equal to series R) MAXIMUM (Purely resistive, high) |
- | Line (Source) Current MAXIMUM (I = V / R) MINIMUM (Near zero line current) |
- | Internal Circulating I Equal to line current EXTREMELY HIGH (Circulates in LC) |
- | Phase Angle at f₀ 0° (Purely resistive) 0° (Purely resistive) |
- | Below Resonance (f<f₀) Capacitive (X_C > X_L) Inductive (Draws inductive current|
- | Above Resonance (f>f₀) Inductive (X_L > X_C) Capacitive (Draws capacitive I) |
- | Typical Application Band-pass filters, traps Amplifier plate/collector loads, |
- | (series notch), antenna feeds antenna traps, oscillators |
- +-----------------------------------------------------------------------------------------+
- Series Resonant Circuit Dynamics
In a series RLC circuit at resonance:
The + 90 ∘ +90^\circ + 9 0 ∘ voltage across the inductor and the − 90 ∘ -90^\circ − 9 0 ∘ voltage across the capacitor are equal in magnitude and 180 ∘ 180^\circ 18 0 ∘ out of phase, completely canceling each other out ( V L + V C = 0 V_L + V_C = 0 V L + V C = 0 ).
Total impedance collapses to its absolute minimum value, which is simply the series internal resistance R R R .
The source delivers maximum current ( I = V source / R I = V_{\text{source}} / R I = V source / R ).
Parallel Resonant Circuit (Tank Circuit) Dynamics
In a parallel LC network (commonly called an LC tank circuit ):
The branch currents through the inductor and capacitor are equal in magnitude and 180 ∘ 180^\circ 18 0 ∘ out of phase. They circulate back and forth between the electric field of the capacitor and the magnetic field of the inductor.
Because these circulating branch currents cancel at the external nodes, the net current drawn from the external source (the line current) drops to a minimum .
Consequently, the terminal impedance across the parallel tank reaches a maximum ( Z tank = L / ( R C ) ≈ Q ⋅ X L Z_{\text{tank}} = L / (R C) \approx Q \cdot X_L Z tank = L / ( RC ) ≈ Q ⋅ X L ).
Parallel tank circuits are universally employed as resonant load impedances in RF power amplifiers to extract maximum output power at the fundamental frequency while suppressing harmonics.
4. Quality Factor ( Q Q Q ) & Resonant Bandwidth
The Quality Factor ( Q Q Q ) is a dimensionless figure of merit that quantifies the energy storage efficiency and frequency selectivity of a resonant circuit. Mathematically, Q Q Q is defined as 2 π 2\pi 2 π times the ratio of energy stored to energy dissipated per cycle: Q = Energy Stored per Cycle Energy Dissipated per Cycle Q = \frac{\text{Energy Stored per Cycle}}{\text{Energy Dissipated per Cycle}} Q = Energy Dissipated per Cycle Energy Stored per Cycle
Formulas for Calculating Quality Factor
For a series resonant circuit with series loss resistance R R R : Q = X L R = X C R = 2 π f 0 L R Q = \frac{X_L}{R} = \frac{X_C}{R} = \frac{2\pi f_0 L}{R} Q = R X L = R X C = R 2 π f 0 L
For a resonant circuit where center frequency ( f 0 f_0 f 0 ) and half-power (-3 dB) bandwidth ( BW \text{BW} BW ) are known: Q = f 0 BW ⟺ BW = f 0 Q Q = \frac{f_0}{\text{BW}} \iff \text{BW} = \frac{f_0}{Q} Q = BW f 0 ⟺ BW = Q f 0 Signal Amplitude
- ^
- | * Center Frequency (f₀)
- 1.0 --+ / \
- | / \
- 0.707 --+--------------*-----*--------- Half-Power (-3 dB) Level
- (1/√2) | /| |\
- | / | | \
- | / | | \
- | / | | \
- 0.0 --+---------+----+-----+----+-----> Frequency
- f₁ f₀ f₂
- |<--- BW --->|
- (BW = f₂ - f₁)
- The Half-Power (-3 dB) Bandwidth
The bandwidth ( BW \text{BW} BW ) of a tuned resonant circuit is formally defined as the frequency span between the lower half-power cutoff frequency ( f 1 f_1 f 1 ) and upper half-power cutoff frequency ( f 2 f_2 f 2 ): BW = f 2 − f 1 \text{BW} = f_2 - f_1 BW = f 2 − f 1
At frequencies f 1 f_1 f 1 and f 2 f_2 f 2 :
Output voltage drops to 70.7 % 70.7\% 70.7% ( 1 / 2 ≈ 0.7071 1/\sqrt{2} \approx 0.7071 1/ 2 ≈ 0.7071 ) of the peak resonant voltage.
Power delivered to the load drops to exactly 50 % 50\% 50% (half-power, or − 3 dB -3\text{ dB} − 3 dB ) of maximum resonant power.
High Q Q Q vs. Low Q Q Q Engineering Trade-offs
High Q Q Q ( Q > 50 Q > 50 Q > 50 ): Produces a very sharp, steep resonance curve with a narrow bandwidth. High Q Q Q provides excellent adjacent-channel selectivity in receiver IF filters and tight harmonic suppression in transmitters. However, excessive Q Q Q can cause ringing, clip audio sidebands, and require frequent retuning across the band.
Low Q Q Q ( Q < 10 Q < 10 Q < 10 ): Produces a broad, flat frequency response with wide bandwidth. Low Q Q Q is desirable in broadband matching networks and wideband antennas, but provides poor rejection of out-of-band signals.
Worked Example: Resonant Bandwidth Calculation
Problem: A tuned RF band-pass filter centered at 7.15 MHz 7.15\text{ MHz} 7.15 MHz ( 7 , 150 kHz 7,150\text{ kHz} 7 , 150 kHz ) has a Quality Factor ( Q Q Q ) of 50 50 50 . What is the half-power ( − 3 dB -3\text{ dB} − 3 dB ) bandwidth of the filter? BW = f 0 Q = 7 , 150 kHz 50 = 143 kHz \text{BW} = \frac{f_0}{Q} = \frac{7,150\text{ kHz}}{50} = 143\text{ kHz} BW = Q f 0 = 50 7 , 150 kHz = 143 kHz
The filter passes frequencies within a 143 kHz 143\text{ kHz} 143 kHz window (from approximately 7.0785 MHz 7.0785\text{ MHz} 7.0785 MHz to 7.2215 MHz 7.2215\text{ MHz} 7.2215 MHz ) before signal power drops by more than 3 dB 3\text{ dB} 3 dB .