Study guide

10.2 Directional Antennas: Yagi-Uda, Cubical Quad & Phased Arrays

FCC Amateur Radio General License Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Introduction & Exam Strategy

1.1 General Class License Overview, Exam Format & Question Pool Structure 1.2 Core Study Strategies, Formula Quick Reference & Test-Taking Tactics

2 Chapter 2: Subelement G1 – Commission's Rules

2.1 General Class Band Privileges & ITU Regions 2.2 Antenna Structure Limits, Beacons & Security Rules 2.3 Transmitter Power Limits, 60-Meter Band Rules & Prohibited Transmissions 2.4 Volunteer Examiner Accreditation, Exam Administration & Remote Testing 2.5 Control Operator Categories, Repeaters, Third-Party Traffic & Station Identification

3 Chapter 3: Subelement G2 – Operating Procedures

3.1 HF Phone Operating Procedures, SSB Tuning & Phonetic Alphabet 3.2 CW Operating Procedures, Q-Signals, RIT/XIT & Split Operation 3.3 Digital Operating Procedures: FT8, JS8Call, PSK31 & RTTY 3.4 Emergency Communications, Traffic Nets, RACES, ARES & Distress Priority 3.5 Volunteer Monitor Program, HF Direction Finding & Azimuthal Maps

4 Chapter 4: Subelement G3 – Radio Wave Propagation

4.1 Solar Activity, Sunspots, Solar Flux Index & Geomagnetic Indices 4.2 Maximum Usable Frequency (MUF), Lowest Usable Frequency (LUF) & Ionospheric Layers 4.3 Skywave Propagation, NVIS, HF Scatter & Tropospheric Ducting

5 Chapter 5: Subelement G4 – Amateur Radio Practices

5.1 Station Setup, Speech Processors & Audio DSP Filters 5.2 Test Equipment: RF Wattmeters, SWR Bridges, Dummy Loads & Oscilloscopes 5.3 Radio Frequency Interference (RFI), TVI, Harmonics & Core Filtering 5.4 Station Grounding, Bonding & Lightning Protection 5.5 Mobile and Portable HF Operations, Vehicle Noise & Battery Systems

6 Chapter 6: Subelement G5 – Electrical Principles

6.1 Reactance, Impedance, Resonance & Quality Factor (Q) 6.2 Decibels, Power Calculations & RMS/Peak AC Voltage Conversions 6.3 Power Factor, Transformer Ratios & Resistive Voltage Dividers

7 Chapter 7: Subelement G6 – Circuit Components

7.1 Inductors, Toroid Cores, Crystals & Semiconductor Diodes 7.2 Transistors (BJT, FET), Voltage Regulators & Vacuum Tube Amplifiers

8 Chapter 8: Subelement G7 – Practical Circuits

8.1 Linear Power Supplies, Rectifier Circuits & Filter Capacitors 8.2 RF Filters, Oscillators (Colpitts, Hartley, Pierce) & Mixers 8.3 Superheterodyne Receivers, Direct Sampling SDRs & Transceiver Architecture

9 Chapter 9: Subelement G8 – Signals and Emissions

9.1 SSB, CW, AM & FM Modulation Principles & Carrier Suppression 9.2 Frequency Mixing, Intermodulation Distortion (IMD) & Bandwidth Standards 9.3 Digital Emission Protocols, Baudot, PSK, FSK & Symbol Rates

10 Chapter 10: Subelement G9 – Antennas and Feed Lines

10.1 Half-Wave Dipoles, Quarter-Wave Verticals & Radiation Patterns 10.2 Directional Antennas: Yagi-Uda, Cubical Quad & Phased Arrays 10.3 Transmission Lines, Characteristic Impedance, Attenuation & SWR 10.4 Antenna Tuners, Impedance Matching Networks & Baluns

11 Chapter 11: Subelement G0 – Electrical and RF Safety

11.1 RF Exposure Evaluation, Maximum Permissible Exposure (MPE) & Safety Offsets 11.2 Tower Safety, Fall Arrest Gear, Antenna Installation & AC Power Hazards

10.2 Directional Antennas: Yagi-Uda, Cubical Quad & Phased Arrays

Key Takeaways Explain This Topic AI

A Yagi-Uda parasitic array concentrates RF energy into a focused directional beam through mutual electromagnetic coupling between a driven element and unpowered parasitic elements along a central boom.

In a standard Yagi antenna, the reflector element is approximately 5% physically longer than the resonant driven element (inductive reactance), while director elements are approximately 5% physically shorter (capacitive reactance).

Forward antenna gain is expressed either in dBi (relative to an isotropic radiator) or dBd (relative to a half-wave dipole), where dBi = dBd + 2.15 dB; overall gain is governed primarily by boom length and element spacing.

Cubical Quad and Delta Loop antennas are full-wave closed perimeter loops (L = 1005 / f_MHz) providing 1.5 to 2 dB higher forward gain than comparable Yagis and significantly lower precipitation static noise.

Parasitic element loading drops the driven element feedpoint impedance to 15-25 ohms, requiring matching systems such as the Gamma match (series capacitor and sliding rod) or Hairpin match (shunt inductor with shortened capacitive element) to step up impedance to 50 ohms.

Last updated: August 2026

10.2 Directional Antennas: Yagi-Uda, Cubical Quad & Phased Arrays

While omnidirectional verticals and bidirectional dipoles radiate energy across wide geographical sectors, directional gain antennas (commonly called "beams") concentrate transmitted RF power into a focused main lobe in a specific azimuthal direction. By focusing energy in the desired direction, directional antennas simultaneously amplify transmitted signal strength toward the target station and reject unwanted interfering signals arriving from the sides and rear during reception.

Understanding the operating principles of parasitic arrays , including the Yagi-Uda , the Cubical Quad , Delta Loops , and their specialized impedance matching networks , is a vital component of the FCC General Class examination. This section explores the electromagnetic coupling, phase relationships, gain metrics, and matching systems that make directional antennas the cornerstone of high-performance HF stations.

1. Principles of Directional Parasitic Arrays

Unlike phased arrays where every antenna element is directly connected to the transmitter feedline, a parasitic array feeds RF power directly to only one element—designated the driven element . All other elements are unpowered conductors called parasitic elements , mounted parallel to the driven element along a central mechanical boom. +-----------------------------------------------------------------------------------------+

  • | 3-ELEMENT YAGI-UDA ARRAY TOPOLOGY |
  • | |
  • | <================ MAIN FORWARD LOBE RADIATION =============== |
  • | |
  • | +-------------------------------------------------------------------------+ |
  • | | CENTRAL BOOM | |
  • | +-------------------------------------------------------------------------+ |
  • | | | | |
  • | | | | |
  • | +-----------+ +-----------+ +-----------+ |
  • | | | | | | | |
  • | | REFLECTOR | | DRIVEN | | DIRECTOR | |
  • | | ELEMENT | | ELEMENT | | ELEMENT | |
  • | | (+5% Long)| | (Resonant)| | (-5% Short) |
  • | | Inductive | | Center-Fed| | Capacitive| |
  • | | | | | | | |
  • | +-----------+ +-----------+ +-----------+ |
  • | |<------- Spacing 0.15-0.25λ ------->|<--- Spacing 0.1-0.2λ -->| |
  • | | | | |
  • | [REAR] [FEED] [FORWARD] |
  • +-----------------------------------------------------------------------------------------+
  • How Parasitic Coupling Works

The driven element radiates an initial electromagnetic field.

This field induces RF currents in the adjacent parasitic elements through mutual electromagnetic coupling.

The induced currents cause each parasitic element to re-radiate electromagnetic waves.

By precisely engineering the length (which determines element reactance) and spacing (which introduces spatial transit phase delay) of each element, the re-radiated waves reinforce constructively in the forward direction and cancel destructively to the rear and sides .

2. Anatomy & Tuning of the Yagi-Uda Array

A standard Yagi-Uda beam (invented by Japanese researchers Hidetsugu Yagi and Shintaro Uda in 1926) utilizes three distinct classes of elements:

1. The Driven Element

A resonant half-wave dipole ( L ≈ 468 / f MHz L \approx 468 / f_{\text{MHz}} L ≈ 468/ f MHz ​ ) connected directly to the transmission feedline.

Operates at zero net reactance ( X = 0 X = 0 X = 0 ) at the design frequency.

2. The Reflector Element

Positioned behind the driven element at a spacing of 0.15 λ 0.15\lambda 0.15 λ to 0.25 λ 0.25\lambda 0.25 λ .

Physically cut approximately 5% longer than the driven element ( L ref ≈ 492 / f MHz L_{\text{ref}} \approx 492 / f_{\text{MHz}} L ref ​ ≈ 492/ f MHz ​ ).

Phase & Reactance: Because it is longer than resonant half-wave length, the reflector exhibits inductive reactance ( + j X L +jX_L + j X L ​ ). The induced current lags the inducing field in phase, causing the re-radiated wave to cancel energy traveling toward the rear while reflecting energy forward toward the driven element.

3. The Director Elements

Positioned ahead of the driven element in the desired direction of transmission at spacings of 0.10 λ 0.10\lambda 0.10 λ to 0.20 λ 0.20\lambda 0.20 λ .

Physically cut approximately 5% shorter than the driven element ( L dir ≈ 445 / f MHz L_{\text{dir}} \approx 445 / f_{\text{MHz}} L dir ​ ≈ 445/ f MHz ​ ).

Phase & Reactance: Because they are shorter than resonant length, directors exhibit capacitive reactance ( − j X C -jX_C − j X C ​ ). The induced current leads the inducing field, pulling and focusing the electromagnetic wavefront forward like an optical lens.

Multiple Directors: Adding more directors increases forward gain and sharpens directivity. A beam can have only one reflector behind the driven element, but can incorporate multiple directors (3, 4, 5, or more) ahead of it along an extended boom.

Boom Length vs. Gain

In Yagi design, forward gain is primarily determined by overall boom length , rather than merely the total number of elements. Adding elements to a fixed-length boom yields diminishing gain returns, though it sharpens the Front-to-Back ratio and widens operational bandwidth.

  • 3. Directional Gain Metrics: dBi, dBd & Rejection Ratios
  • Gain References: dBi vs. dBd

Antenna forward gain quantifies the increase in effective radiated field strength in the main lobe compared to a reference antenna receiving the same input power: +-----------------------------------------------------------------------------------------+

  • | ANTENNA GAIN CONVERSION (dBi vs dBd) |
  • | |
  • | ISOTROPIC RADIATOR (dBi): HALF-WAVE DIPOLE (dBd): |
  • | - Theoretical point source - Real physical half-wave wire |
  • | - Radiates equally in a 360° sphere - Exhibits 2.15 dBi intrinsic gain |
  • | |
  • | dBi = dBd + 2.15 dB | dBd = dBi - 2.15 dB |
  • +-----------------------------------------------------------------------------------------+

Practical Conversion Examples:

An antenna with a gain of 7.0 dBd 7.0\text{ dBd} 7.0 dBd has a gain of 7.0 + 2.15 = 9.15 dBi 7.0 + 2.15 = 9.15\text{ dBi} 7.0 + 2.15 = 9.15 dBi .

An antenna with a gain of 12.15 dBi 12.15\text{ dBi} 12.15 dBi has a gain of 12.15 − 2.15 = 10.0 dBd 12.15 - 2.15 = 10.0\text{ dBd} 12.15 − 2.15 = 10.0 dBd .

Front-to-Back (F/B) Ratio & Front-to-Side Rejection

Front-to-Back (F/B) Ratio: The ratio (expressed in decibels) of signal strength radiated in the maximum forward direction to the signal strength radiated in the exact opposite direction ( 180 ∘ 180^\circ 18 0 ∘ rearward). High-performance Yagis achieve F/B ratios between 20 dB 20\text{ dB} 20 dB and 30 dB 30\text{ dB} 30 dB , effectively silencing rear co-channel interference.

Front-to-Side Rejection: The ratio of forward gain to radiation at 90 ∘ 90^\circ 9 0 ∘ and 270 ∘ 270^\circ 27 0 ∘ . Directional beams feature deep nulls off their sides, allowing operators to rotate the antenna to null out adjacent interference.

4. Driven Element Feedpoint Impedance & Matching Networks

When parasitic elements are brought into close proximity to the driven element, intense mutual impedance loading dramatically reduces the radiation resistance of the driven element from 73 Ω 73\ \Omega 73 Ω down to 15 Ω to 25 Ω 15\ \Omega\text{ to }25\ \Omega 15 Ω to 25 Ω (or even lower on tightly spaced, high-gain arrays).

Connecting a 50 Ω 50\ \Omega 50 Ω coaxial cable directly to a 20 Ω 20\ \Omega 20 Ω driven element would result in an unacceptable SWR of 50 / 20 = 2.5 : 1 50 / 20 = 2.5:1 50/20 = 2.5 : 1 . To achieve a perfect 1 : 1 1:1 1 : 1 SWR match, specialized RF matching networks are integrated at the antenna feedpoint: +-----------------------------------------------------------------------------------------+

  • | GAMMA MATCH & HAIRPIN (BETA) MATCH |
  • | |
  • | GAMMA MATCH (UNBALANCED COAX MATCH): |
  • | - Driven element is a continuous unbroken metal rod (grounded to boom at center) |
  • | - Coax braid connects directly to boom/element center |
  • | - Coax center pin connects through a variable series capacitor into a parallel rod |
  • | - Sliding shorting strap adjusts resistance; series capacitor tunes out inductance |
  • | |
  • | HAIRPIN / BETA MATCH (BALANCED MATCH): |
  • | - Driven element is cut slightly short (presents capacitive reactance R - jX) |
  • | - A U-shaped metal conductor (shunt inductor) is wired across the split center feed |
  • | - Forms an L-network that steps up 15-25 Ω to 50 Ω pure resistance |
  • +-----------------------------------------------------------------------------------------+
  • 1. The Gamma Match

Mechanical Advantage: The driven element does not need to be split or insulated from the conductive metal boom; the entire aluminum tube can be directly clamped and grounded to the boom, providing superior lightning protection and structural strength.

Electrical Operation: A smaller parallel rod runs alongside one half of the driven element. The coaxial cable shield connects to the center of the boom, while the center conductor connects through a series variable capacitor into the gamma rod. An adjustable sliding shorting bar bridges the gamma rod to the driven element.

Tuning: The sliding bar sets the stepped-up resistance to 50 Ω 50\ \Omega 50 Ω , while the series capacitor cancels the inductive reactance introduced by the parallel gamma rod loop.

2. The Hairpin (Beta) Match

Electrical Operation: The driven element is intentionally cut slightly shorter than resonance so that its feedpoint impedance exhibits a capacitive reactive component ( Z feed = R − j X Z_{\text{feed}} = R - jX Z feed ​ = R − j X , typically 20 − j 40 Ω 20 - j40\ \Omega 20 − j 40 Ω ).

A U-shaped rigid conductor (hairpin) or coil is placed across the split feedpoint, acting as a shunt inductor ( + j X L +jX_L + j X L ​ ). The shunt inductor and series capacitance form a classic L-network that transforms the 20 Ω 20\ \Omega 20 Ω resistance up to a pure 50 Ω 50\ \Omega 50 Ω resistive match.

5. Full-Wave Loop Beams: Cubical Quads & Delta Loops

A Cubical Quad antenna uses full-wave perimeter closed wire loops mounted on non-conductive spreaders (such as fiberglass cross-arms) rather than linear half-wave tubing elements. +-----------------------------------------------------------------------------------------+

  • | 2-ELEMENT CUBICAL QUAD ARRAY |
  • | |
  • | <========= FORWARD DIRECTION OF PROPAGATION ======== |
  • | |
  • | +---------------+ +---------------+ |
  • | /| /| /| /| |
  • | / | / | / | / | |
  • | +--+------------+ | +--+------------+ | |
  • | | | REFLECTOR | | | | DRIVEN | | |
  • | | | LOOP | | BOOM | | LOOP | | |
  • | | | (1030/f) | | =========|==|== (1005/f) |==|==== |
  • | | +------------+--+ | +------------+--+ |
  • | | / | / | / | / |
  • | |/ |/ |/ |/ |
  • | +---------------+ +---------------+ |
  • | [Feedpoint] |
  • +-----------------------------------------------------------------------------------------+
  • Calculating Full-Wave Loop Dimensions

The total perimeter length ( L L L ) in feet of a resonant full-wave closed loop is given by: L driven (feet) = 1005 f MHz L_{\text{driven (feet)}} = \frac{1005}{f_{\text{MHz}}} L driven (feet) ​ = f MHz ​ 1005 ​

Reflector Loop: Cut approximately 3% to 5% larger ( L ref ≈ 1030 / f MHz L_{\text{ref}} \approx 1030 / f_{\text{MHz}} L ref ​ ≈ 1030/ f MHz ​ ) or tuned with a closed stub.

Director Loop: Cut approximately 3% to 5% smaller ( L dir ≈ 975 / f MHz L_{\text{dir}} \approx 975 / f_{\text{MHz}} L dir ​ ≈ 975/ f MHz ​ ).

Operational Advantages of Cubical Quads & Delta Loops over Yagis:

Higher Forward Gain: A 2-element Quad provides approximately 1.5 to 2.0 dB 1.5\text{ to }2.0\text{ dB} 1.5 to 2.0 dB higher gain than a comparable 2-element Yagi of the same boom length.

Lower Precipitation Static Noise: The continuous closed-loop electrical geometry allows high-voltage electrostatic charges from windblown rain, snow, and dust to drain off naturally to ground, resulting in a substantially lower noise floor during stormy weather.

Flexible Polarization: Feeding the quad loop at the center of the bottom or top horizontal wire produces horizontal polarization ; feeding the loop at the center of either vertical side wire produces vertical polarization .

Wider SWR Bandwidth: Closed full-wave loops generally exhibit a broader 2:1 SWR operating bandwidth across the amateur band.

6. Directional Antenna Specifications Matrix

Antenna Type Typical Elements Boom Length Forward Gain (dBi) Forward Gain (dBd) Typical F/B Ratio Feedpoint Matching Method

3-Element Yagi 3 (Ref, DE, Dir) 0.25 λ − 0.45 λ 0.25\lambda - 0.45\lambda 0.25 λ − 0.45 λ 7.0 − 8.5 dBi 7.0 - 8.5\text{ dBi} 7.0 − 8.5 dBi 5.0 − 6.5 dBd 5.0 - 6.5\text{ dBd} 5.0 − 6.5 dBd 20 − 30 dB 20 - 30\text{ dB} 20 − 30 dB Gamma match, Hairpin (Beta) match, or T-match.

5-Element Yagi 5 (Ref, DE, 3 Dirs) 0.75 λ − 1.2 λ 0.75\lambda - 1.2\lambda 0.75 λ − 1.2 λ 10.5 − 12.0 dBi 10.5 - 12.0\text{ dBi} 10.5 − 12.0 dBi 8.5 − 10.0 dBd 8.5 - 10.0\text{ dBd} 8.5 − 10.0 dBd 25 − 35 dB 25 - 35\text{ dB} 25 − 35 dB Gamma match or Hairpin match stepping up 12 − 18 Ω 12-18\ \Omega 12 − 18 Ω .

2-Element Cubical Quad 2 (Ref, DE) 0.15 λ − 0.20 λ 0.15\lambda - 0.20\lambda 0.15 λ − 0.20 λ 7.0 − 8.0 dBi 7.0 - 8.0\text{ dBi} 7.0 − 8.0 dBi 5.0 − 6.0 dBd 5.0 - 6.0\text{ dBd} 5.0 − 6.0 dBd 18 − 25 dB 18 - 25\text{ dB} 18 − 25 dB Direct 50 Ω 50\ \Omega 50 Ω feed or 75 Ω 75\ \Omega 75 Ω matching quarter-wave stub.

3-Element Cubical Quad 3 (Ref, DE, Dir) 0.30 λ − 0.40 λ 0.30\lambda - 0.40\lambda 0.30 λ − 0.40 λ 9.5 − 11.0 dBi 9.5 - 11.0\text{ dBi} 9.5 − 11.0 dBi 7.5 − 9.0 dBd 7.5 - 9.0\text{ dBd} 7.5 − 9.0 dBd 22 − 30 dB 22 - 30\text{ dB} 22 − 30 dB Direct feed or Gamma match.

Delta Loop Beam 2 to 3 triangular loops 0.20 λ − 0.35 λ 0.20\lambda - 0.35\lambda 0.20 λ − 0.35 λ 7.0 − 9.5 dBi 7.0 - 9.5\text{ dBi} 7.0 − 9.5 dBi 5.0 − 7.5 dBd 5.0 - 7.5\text{ dBd} 5.0 − 7.5 dBd 18 − 25 dB 18 - 25\text{ dB} 18 − 25 dB 4 : 1 4:1 4 : 1 balun or Gamma match.

Loading diagram... Yagi Parasitic Element Reactance, Phase Dynamics and Forward Wave Formation