Study guide
4.1 Container Recognition
Hazardous Materials Technician Certification Exam
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Exam Overview
1.1 Current Exam Facts 1.2 Technician Role and Response Levels 1.3 NFPA 470, OSHA HAZWOPER, and APIE-T
2 Hazard Identification Systems
2.1 DOT Hazard Classes 1–9 2.2 Placards, Labels, and GHS Pictograms 2.3 UN/NA Numbers and NFPA 704 2.4 SDS and Shipping Papers
3 Reference Sources and Chemical Properties
3.1 Emergency Response Guidebook (ERG 2024) 3.2 Collecting and Interpreting Hazard Information 3.3 Chemical and Physical Properties for Responders
4 Containers, Damage, and Behavior
4.1 Container Recognition 4.2 Container Damage Assessment 4.3 Predicting Material and Container Behavior 4.4 Estimating the Endangered Area
5 PPE Ensembles and Chemical Protective Clothing
5.1 EPA/OSHA PPE Levels A–D 5.2 Chemical Protective Clothing Types and NFPA Standards 5.3 Permeation, Penetration, Degradation, and Compatibility 5.4 Respiratory Protection: SCBA and Air-Purifying Respirators
6 PPE Selection and Operations
6.1 Selecting Technician-Level PPE 6.2 Donning, Doffing, and Working in PPE 6.3 Heat Stress, Work/Rest, and the Buddy System 6.4 PPE Programs and Medical Surveillance
7 Decontamination Fundamentals
7.1 Contamination vs Exposure 7.2 Emergency Decontamination 7.3 Technical Decontamination and Corridor Setup 7.4 Decontamination Methods and Solutions
8 Mass Decontamination and Effectiveness
8.1 Mass Decontamination 8.2 Equipment Decon and Runoff Control 8.3 Evaluating Decontamination Effectiveness
9 Product Control Fundamentals
9.1 Containment vs Confinement 9.2 Confinement Techniques 9.3 Plugging and Patching 9.4 Overpacking Nonbulk and Radioactive Packages
10 Offensive Control and Rescue
10.1 Pressurized Containers and Chlorine Kits A/B/C 10.2 MC 306/DOT 406 Dome Clamp, Grounding, and Bonding 10.3 Liquid Product Transfer 10.4 Victim Rescue and Recovery in the Hot Zone
11 Air Monitoring Fundamentals
11.1 Monitoring Strategy, Bump Tests, and Calibration 11.2 Four-Gas Meters and Combustible Gas Indicators 11.3 Photoionization and Flame Ionization Detectors
12 Specialized Detection
12.1 Colorimetric Detector Tubes 12.2 Radiation Types and Detection Instruments 12.3 Interpreting Monitoring Data and Instrument Limits
13 Toxicology Fundamentals
13.1 Routes of Exposure 13.2 Dose-Response, Acute vs Chronic Effects 13.3 Exposure Limits: PEL, TLV, STEL, Ceiling, IDLH, REL
14 Health Effects and CBRN Hazards
14.1 Chemical Health Effects and Target Organs 14.2 Biological Hazards and CBRN/WMD Agents
15 Incident Command and Site Control
15.1 ICS Structure for Hazmat Incidents 15.2 Control Zones and the Site Safety Plan 15.3 Incident Action Plan and Response Objectives
16 Evaluation and Termination
16.1 Evaluating and Reporting Progress 16.2 Termination, Documentation, and Evidence Preservation
4.1 Container Recognition
Key Takeaways Explain This Topic AI
49 CFR 171.8 non-bulk packagings have a maximum capacity of 119 gallons (450 L) or less for a liquid, a maximum net mass of 882 pounds (400 kg) or less and 119 gallons or less for a solid, or a water capacity of 1,000 pounds (454 kg) or less for a gas; larger packagings are bulk.
MC 306/DOT 406 cargo tanks are elliptical aluminum atmospheric tanks (MAWP 2.65–4 psig) typically carrying gasoline or diesel; MC 307/DOT 407 tanks are circular with MAWP of at least 25 psig for chemicals; MC 312/DOT 412 tanks are smaller-diameter circular tanks with external stiffener rings for corrosives.
MC 331 tanks are circular high-pressure vessels (design pressure 100–500 psig) with rounded heads for liquefied gases such as LPG, anhydrous ammonia, and chlorine; MC 338 tanks are vacuum-insulated cryogenic cargo tanks.
Chlorine 100 lb and 150 lb cylinders are commonly DOT 3A/3AA; a chlorine ton container is a DOT 106A500X holding about 2,000 lb, with two valves on one head and six fusible plugs.
Shape is a recognition clue, not identity: confirm the specification plate, placard, four-digit ID, and shipping papers before you name the product.
Last updated: August 2026
4.1 Container Recognition
Quick Answer: Read the container before you commit people. Non-bulk under 49 CFR 171.8 means a liquid receptacle of 119 gallons (450 L) or less, a solid receptacle of 882 pounds (400 kg) or less and 119 gallons or less, or a gas receptacle with 1,000 pounds (454 kg) water capacity or less. Larger is bulk . Highway silhouettes: MC 306 / DOT 406 elliptical aluminum fuel tanks; MC 307 / DOT 407 circular chemical tanks; MC 312 / DOT 412 smaller diameter with external stiffener rings (corrosives); MC 331 rounded-head high-pressure liquefied gases; MC 338 vacuum-insulated cryogenic. Shape is a clue . The specification plate plus placards and papers are identification.
NFPA 470 technician job performance requirements in Chapter 11.2 assume you can tell a 55-gallon drum from a cargo tank and a pressure tank car from a general-service car before you predict behavior. OSHA 29 CFR 1910.120(q)(6)(iii)(B) still requires classification and identification; the container is often the first honest clue when the diamond is dirty, missing, or wrong. If you call every shiny highway tank a gasoline tanker, you will pick the wrong isolation, the wrong PPE, and the wrong kit.
Bulk versus non-bulk (DOT definitions, not slang)
Street language uses "bulk" to mean "a lot of product." PHMSA uses 49 CFR 171.8 . Quote the thresholds; do not invent a gallon number of your own.
Non-bulk packaging means a packaging that has:
A maximum capacity of 450 L (119 gallons) or less as a receptacle for a liquid ;
A maximum net mass of 400 kg (882 pounds) or less and a maximum capacity of 450 L (119 gallons) or less as a receptacle for a solid ; or
A water capacity of 454 kg (1,000 pounds) or less as a receptacle for a gas as defined in 49 CFR 173.115.
Bulk packaging is a packaging, other than a vessel or a barge, including a transport vehicle or freight container, in which hazardous materials are loaded with no intermediate form of containment, and that exceeds those same three thresholds (greater than 119 gallons for a liquid; greater than 882 pounds and 119 gallons for a solid; greater than 1,000 pounds water capacity for a gas). A Large Packaging with inner packagings can still be bulk under the same definition.
Why the line matters: placarding, identification-number display, and many ERG "small package versus large package" instincts start here. A 275-gallon tote (IBC) of liquid is bulk . A 55-gallon drum is non-bulk . A chlorine ton container (about 2,000 lb of product, water capacity well above 1,000 lb) is bulk . A 150 lb chlorine cylinder is non-bulk as a gas receptacle. Do not call a tote a drum because both sit on a pallet.
Drums: steel, poly, fiber; open versus tight head
The workhorse non-bulk liquid/solid package is the 55-gallon (208 L) drum.
Construction Typical UN codes What it usually holds Recognition
Steel 1A1 tight head; 1A2 open head Flammable liquids, wastes, some corrosives (often lined) Painted or rusty steel, rolling hoops, bung openings or a removable lid
Plastic (poly) 1H1 tight head; 1H2 open head Corrosives, some oxidizers, water-treatment chemicals Translucent or colored polyethylene; no steel sparking
Fiber 1G Solids, powders, some pastes — not a high-vapor-pressure liquid can Fiberboard sidewall, often a plastic liner and a steel or fiber lid
Tight-head (closed-head) drums have bungs in a non-removable top. They are the liquid package. Open-head drums have a removable cover held by a bolt ring or lever lock. They are the solids, sludges, and waste package. An open-head drum of liquid is a weaker liquid container than a tight-head drum of the same steel. Overpack and leak-control tactics later in this guide depend on that distinction.
A drum farm is not one product. Weathered labels, mixed colors, and missing bungs mean unknowns . Recognition of package type is not recognition of contents .
Cylinders and ton containers
DOT 3A / 3AA seamless steel cylinders are the common high-pressure compressed-gas package. In chlorine service the usual sizes technicians drill on are 100 lb and 150 lb (product weight, not the tare of the empty cylinder). The valve typically includes a fusible plug in the valve body. Chlorine Institute Kit A is built for those cylinders. Do not assume every 3A/3AA is chlorine — the same family carries many compressed gases. Read the stenciling, the collar, and the CGA valve connection.
A ton container in chlorine service is a horizontal welded tank built to DOT 106A500X , holding about 2,000 lb (907 kg) of chlorine (a short ton of product). Recognition points:
About 30 inches in diameter and about 80–82 inches long.
Two valves on one concave head, protected by a bonnet. With the valves aligned vertically , the upper valve draws gas and the lower valve draws liquid (eduction tubes reach the opposite sides of the shell).
Six fusible plugs : three in each head , spaced about 120 degrees apart. The fusible metal is designed to melt at 158–165 °F (70–74 °C) per the 49 CFR 173.301(f) temperature window.
Stamped data on the chime: specification, serial, tare, hydrostatic test date, water capacity.
Kit B is the Chlorine Institute kit for the 106A500X. The same DOT specification can carry other compressed gases; a "chlorine ton" silhouette is still not a laboratory identification.
Highway cargo tanks: silhouette first, plate second
MC specifications (MC 306, 307, 312, 331, 338) are the older cargo-tank specs. DOT 400-series specs (406, 407, 412) replaced 306/307/312 for new construction after the early 1990s. Both generations are still on the road. Teach them as pairs.
Spec Shape / visual cues Typical MAWP / design Typical contents
MC 306 / DOT 406 Elliptical / oval cross-section from the rear; often aluminum ; relatively flat heads; rollover protection and manholes on top; bottom loading/unloading common DOT 406 MAWP no lower than 2.65 psig and no higher than 4 psig — atmospheric / very low pressure Gasoline, diesel, jet fuel , other flammable/combustible liquids
MC 307 / DOT 407 Rounded / circular ("horseshoe" or round) cross-section; often stainless or lined; may be insulated DOT 407: circular tank, MAWP at least 25 psig Chemicals, solvents, many moderate-pressure liquids
MC 312 / DOT 412 Smaller diameter , circular; external stiffener rings (ribs) around the shell; often steel DOT 412 MAWP at least 5 psig ; tanks above 15 psig must be circular ; many corrosive units run well above the 5 psig floor Corrosives (acids, bases)
MC 331 Circular shell, spherical / rounded heads , heavy steel (sometimes aluminum if insulated and compatible); valves often in a rear cabinet or under a protective housing; frequently painted white or light Design pressure not less than 100 psig nor more than 500 psig (49 CFR 178.337-1); product-specific floors in 173.315 (for example 265 psig anhydrous ammonia, 225 psig chlorine) LPG (propane) , anhydrous ammonia , chlorine cargo tanks, other liquefied compressed gases
MC 338 "Thermos bottle": vacuum-insulated double wall, piping cabinet (usually rear), frost or vapor cloud at fittings when cold Cryogenic service; relief and piping designed for refrigerated liquid Refrigerated liquefied gases: nitrogen, oxygen, argon, LNG, carbon dioxide, and similar cryogens
Exam trap: an oval aluminum tank with a red diamond is the gasoline picture — until you actually read 1203 or the papers. A circular tank with stiffener rings is the corrosive picture — Class 8, not "another fuel tanker." A rounded-head white tanker with a green or flammable-gas diamond is the pressure-gas picture, not a 406. MC 338 looks "fat" because of the vacuum jacket; it is not an MC 331.
Specification plates (name plates) are required on cargo tanks (49 CFR 178.345-14 for 406/407/412; 178.337-17 for MC 331). Typical data: specification number, original test date, MAWP , capacity, materials, serial, inspector. Find the plate (often on the left front / street side near the front of the tank) from a safe location. The plate tells you what the tank is built to , not what is in it today. A dedicated 331 in ammonia service that was last loaded with propane is a verification problem, not a silhouette problem.
Rail, intermodal, pipelines, and fixed facilities
Rail tank cars split visually into general-service / non-pressure cars and pressure cars.
General-service (non-pressure) cars (legacy DOT-111 , current flammable-liquid DOT-117 with thicker shell, jacket, thermal protection, and full-height head shields) carry many liquids at relatively low pressure: petroleum, alcohols, some corrosives and toxics. Fittings are less "armored" than on pressure cars.
Pressure tank cars ( DOT-105, 112, 114, 120 and related) are circular, heavily built, with a protective housing (dome) over valves on top. They carry liquefied gases — LPG, anhydrous ammonia, chlorine — and other high-vapor-pressure products. Treat a pressure car like a 331 on rails: the energy is in the lading, not just the wreckage.
Intermodal portable tanks (ISO tanks) sit in a frame that stacks on ships, rail, and chassis. Older plates still say IMO Type 1 / 2 / 5 / 7 ; newer UN portable tanks use T1–T22 (liquids), T50 (non-refrigerated liquefied gases), and T75 (refrigerated liquefied gases). IMO-1 / higher-pressure liquid tanks, IMO-2 lower-pressure liquids, IMO-5 gas tanks, and IMO-7 cryogenic tanks are the recognition set. Read the tank plate on the frame.
Pipelines do not present a cargo-tank silhouette. Markers (49 CFR 192.707 / 195.410) give operator name, product or "gas/petroleum," and a 24-hour number . Product is moving under pressure you cannot see. Isolation is a control-room and valve-station problem, not a drum-overpack problem.
Fixed facilities add ASME pressure vessels , process piping, atmospheric storage tanks, reactors, and totes / IBCs . Composite IBCs (plastic bottle in a cage, often 275 or 330 gallons ) are bulk liquid packagings if they exceed 119 gallons. Process piping can contain the same product as the vessel at a different pressure and temperature. NFPA 704 diamonds on the building may not match every tote in the warehouse.
Exam scenario: five highway tanks, one mistake
You are staged uphill and upwind of a multi-vehicle pileup. Tank A is oval aluminum with manholes on top — 406 / gasoline picture . Tank B is circular stainless without ribs — 407 / chemical picture . Tank C is smaller diameter with external rings — 412 / corrosive picture . Tank D is circular with rounded heads and a rear valve cabinet — 331 / LPG or ammonia or chlorine . Tank E is a heavy vacuum-jacketed tank with a piping cabinet and a white vapor at the vents — 338 / cryogenic . Calling all five "tankers, foam the ditch" is how a technician takes a corrosive bath, a cryogenic freeze burn, or a pressure-gas BLEVE problem. Recognize the container, then verify identity with plate, placard, ID number, and papers — the same identify-then-verify duty as Chapter 3.