Study guide

2.4 SDS and Shipping Papers

Hazardous Materials Technician Certification Exam

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Overview

1.1 Current Exam Facts 1.2 Technician Role and Response Levels 1.3 NFPA 470, OSHA HAZWOPER, and APIE-T

2 Hazard Identification Systems

2.1 DOT Hazard Classes 1–9 2.2 Placards, Labels, and GHS Pictograms 2.3 UN/NA Numbers and NFPA 704 2.4 SDS and Shipping Papers

3 Reference Sources and Chemical Properties

3.1 Emergency Response Guidebook (ERG 2024) 3.2 Collecting and Interpreting Hazard Information 3.3 Chemical and Physical Properties for Responders

4 Containers, Damage, and Behavior

4.1 Container Recognition 4.2 Container Damage Assessment 4.3 Predicting Material and Container Behavior 4.4 Estimating the Endangered Area

5 PPE Ensembles and Chemical Protective Clothing

5.1 EPA/OSHA PPE Levels A–D 5.2 Chemical Protective Clothing Types and NFPA Standards 5.3 Permeation, Penetration, Degradation, and Compatibility 5.4 Respiratory Protection: SCBA and Air-Purifying Respirators

6 PPE Selection and Operations

6.1 Selecting Technician-Level PPE 6.2 Donning, Doffing, and Working in PPE 6.3 Heat Stress, Work/Rest, and the Buddy System 6.4 PPE Programs and Medical Surveillance

7 Decontamination Fundamentals

7.1 Contamination vs Exposure 7.2 Emergency Decontamination 7.3 Technical Decontamination and Corridor Setup 7.4 Decontamination Methods and Solutions

8 Mass Decontamination and Effectiveness

8.1 Mass Decontamination 8.2 Equipment Decon and Runoff Control 8.3 Evaluating Decontamination Effectiveness

9 Product Control Fundamentals

9.1 Containment vs Confinement 9.2 Confinement Techniques 9.3 Plugging and Patching 9.4 Overpacking Nonbulk and Radioactive Packages

10 Offensive Control and Rescue

10.1 Pressurized Containers and Chlorine Kits A/B/C 10.2 MC 306/DOT 406 Dome Clamp, Grounding, and Bonding 10.3 Liquid Product Transfer 10.4 Victim Rescue and Recovery in the Hot Zone

11 Air Monitoring Fundamentals

11.1 Monitoring Strategy, Bump Tests, and Calibration 11.2 Four-Gas Meters and Combustible Gas Indicators 11.3 Photoionization and Flame Ionization Detectors

12 Specialized Detection

12.1 Colorimetric Detector Tubes 12.2 Radiation Types and Detection Instruments 12.3 Interpreting Monitoring Data and Instrument Limits

13 Toxicology Fundamentals

13.1 Routes of Exposure 13.2 Dose-Response, Acute vs Chronic Effects 13.3 Exposure Limits: PEL, TLV, STEL, Ceiling, IDLH, REL

14 Health Effects and CBRN Hazards

14.1 Chemical Health Effects and Target Organs 14.2 Biological Hazards and CBRN/WMD Agents

15 Incident Command and Site Control

15.1 ICS Structure for Hazmat Incidents 15.2 Control Zones and the Site Safety Plan 15.3 Incident Action Plan and Response Objectives

16 Evaluation and Termination

16.1 Evaluating and Reporting Progress 16.2 Termination, Documentation, and Evidence Preservation

2.4 SDS and Shipping Papers

Key Takeaways Explain This Topic AI

OSHA safety data sheets use a 16-section GHS format; technicians use SDS for identity, composition, first aid, firefighting, release, handling, PPE, properties, reactivity, and toxicology — then confirm with monitoring because an SDS can lag the scene.

Shipping papers are mode-specific: bill of lading (highway), consist or wheel report (rail), dangerous cargo manifest (water), and air waybill (air), kept where the crew can reach them.

The DOT basic description order is identification number, proper shipping name, hazard class, then packing group when a packing group is assigned.

Packing groups I, II, and III mean great, medium, and minor danger and are not used for all classes; Class 2 and Class 7 typically have no packing group.

A 24-hour emergency-response telephone number (often CHEMTREC or an equivalent service) is required on shipping papers; an SDS is not a shipping paper, and an ERG orange guide is not SDS-level product data.

Last updated: August 2026

Placards and UN numbers get you into the right family of hazard. Two documents finish identification: the safety data sheet (workplace product data) and the shipping paper (transport legal description). NFPA 470 11.2 has you collect and interpret hazard information. OSHA 1910.120(q)(6)(iii)(B) has you classify and identify. Neither standard lets you treat a wall-mounted SDS as a bill of lading, or an ERG orange guide as a product-specific SDS.

OSHA SDS: 16 sections, not a shipping paper

Under OSHA Hazard Communication (29 CFR 1910.1200), manufacturers and importers supply a safety data sheet in the 16-section GHS format . That is a workplace document. It may travel with a delivery, sit in a binder at a fixed facility, or be emailed from a shipper or CHEMTREC. It is not the DOT shipping paper, even when Section 14 (Transport information) reprints UN data.

The 16 sections, and what a technician actually uses:

  • Section Title Technician use
  • 1 Identification Product name, recommended use, supplier, emergency phone
  • 2 Hazard identification GHS classifications and pictograms
  • 3 Composition / information on ingredients What is in it — the chemistry you cannot get from a Class 3 diamond
  • 4 First-aid measures Route-specific first aid
  • 5 Fire-fighting measures Extinguishing media and fire hazards
  • 6 Accidental release measures Spill tactics and precautions
  • 7 Handling and storage Incompatibilities and storage conditions
  • 8 Exposure controls / personal protection Occupational exposure limits and PPE guidance
  • 9 Physical and chemical properties Flash point, boiling point, vapor density, pH, solubility
  • 10 Stability and reactivity Polymerization, water reactivity, forbidden contacts
  • 11 Toxicological information Routes, acute/chronic effects
  • 12 Ecological information Environmental fate (GHS; not OSHA-mandatory content)
  • 13 Disposal considerations Waste notes (not OSHA-mandatory)
  • 14 Transport information UN/NA, class, packing group reprint (not OSHA-mandatory; still not a shipping paper)
  • 15 Regulatory information Other regulatory lists (not OSHA-mandatory)
  • 16 Other information Preparation and revision dates

OSHA enforces the content of Sections 1–11 and 16. Sections 12–15 are part of the internationally harmonized 16-section layout; OSHA does not police environmental and transport sections the same way because those are outside OSHA's statute. A blank or thin Section 14 does not mean the drum is unregulated in transport.

SDS may lag the scene. The binder in the office may describe last week's product. A blended load, a mis-labeled tote, or a reaction product after fire will not match Section 3. Use the SDS for identification, composition, first aid, firefighting, accidental release, handling, exposure controls/PPE, physical/chemical properties, stability/reactivity, and toxicology — then confirm with monitoring (later chapters) and with what the container and papers actually show.

Shipping papers: the transport identity document

DOT shipping papers carry the basic description of each hazardous material offered for transportation (49 CFR 172.200–172.204, 172.202). The name of the document changes with mode:

Mode Document you ask for Where it lives

Highway Bill of lading (shipping paper) In the cab , within immediate reach of the belted driver, or in a holder on the inside of the driver's door (49 CFR 177.817). When the driver is out of the vehicle, on the driver's seat or in that door holder.

Rail Train consist or wheel report (and any hazardous-material shipping papers for the cars) With the train crew; responders ask the conductor / engineer, not the first boxcar.

Water Dangerous cargo manifest Designated location on the vessel, with the master or person in charge.

Air Air waybill (plus notification to the pilot in command) With the operator / flight crew, not taped to a Unit Load Device as a substitute for the waybill.

If you cannot find papers, say so in the size-up. Missing papers are a fact, not permission to invent a proper shipping name from tank color.

Basic description order (current DOT)

49 CFR 172.202 requires this sequence — and this is the sequence exams use after the U.S. aligned with UN order:

  • Identification number , preceded by UN, NA, or ID as appropriate
  • Proper shipping name (plus technical name in parentheses when required for n.o.s. entries)
  • Hazard class or division number (subsidiary class in parentheses when required)

Packing group in Roman numerals, when a packing group is assigned (PG I, PG II, or PG III, or the Roman numerals alone)

Example: UN1203, Gasoline, 3, PG II

The old order (proper shipping name first, then class, then UN number) is outdated. If an older textbook still leads with the name, do not copy that order onto an exam answer. Quantity, number of packages, emergency-response telephone number, and additional entries (marine pollutant, poison-inhalation-hazard, RQ, EX numbers for explosives) ride with the basic description; they do not replace it.

Packing groups I / II / III

When assigned, packing groups communicate degree of danger :

  • PG I — great danger (highest packing/performance bar among the three)
  • PG II — medium danger
  • PG III — minor danger

Packing groups are not used for all classes . Class 2 gases and Class 7 radioactive materials typically have no packing group . Explosives are organized by division and compatibility group , not PG I–III. Some Class 9 entries have a packing group; some (lithium batteries, dry ice) do not. Never force PG II onto a chlorine 2.3 cylinder just to make the basic description look complete. Never treat a packing group as an NFPA 704 rating: PG I is not a blue 1, and a red 4 is not PG IV.

Emergency contact number and CHEMTREC

49 CFR 172.604 requires a 24-hour emergency-response telephone number on the shipping paper. The number must reach a person who is knowledgeable about the material and has comprehensive emergency-response and incident-mitigation information, or who has immediate access to such a person. Many shippers contract CHEMTREC (Chemical Transportation Emergency Center) or an equivalent emergency-response information service; the number printed on the paper is the one you call, along with the shipper name and the UN/NA number. The 24-hour number is a shipping-paper requirement, not a substitute for having the paper. An SDS emergency phone in Section 1 is useful; it still does not turn the SDS into a bill of lading.

Two traps that fail technician exams

Trap 1: Treating an SDS as a shipping paper. An SDS taped to a visor does not satisfy 49 CFR 172 shipping-paper rules. It may lack the basic description order, the 24-hour number in the required form, the quantity, and the certification. You can use the SDS. You cannot declare that the transport document requirement is met because a GHS SDS was in the cab. Ask again for the bill of lading, consist, dangerous cargo manifest, or air waybill.

Trap 2: Treating the ERG orange guide as SDS-level product-specific data. ERG orange guides are generic for a group of UN numbers that share similar first-responder tactics. Many different products share one guide number. The orange guide will not give you the component percentages in Section 3, the occupational exposure limit in Section 8, or the polymerisation warning in Section 10. Conversely, an SDS will not give you the ERG's isolation distances or the three-digit guide format you use in the first 15 minutes. Use shipping papers + UN/NA + ERG for initial transport actions; use SDS for product-specific chemistry and PPE; use monitoring to confirm what is actually in the air.

How this chapter fits Analyze (11.2)

On a technician assignment you build identification in layers:

Container and occupancy — MC 306/DOT 406 oval versus MC 312/DOT 412 corrosive tanker; warehouse versus highway.

DOT class diamonds — Classes 1–9, divisions, primary and subsidiary, refusing color-alone ID.

Placards vs labels vs GHS — vehicle versus package versus workplace pictogram; orange panel ID number; marine pollutant, inhalation hazard, HOT, fumigant, cargo aircraft only.

UN/NA number — international versus North America-only; ERG yellow-page path; 2024 warfare-agent listing change.

NFPA 704 — facility 0–4 ratings, not a UN number.

Shipping papers — basic description in the correct order, packing group when assigned, 24-hour number, correct document for the mode.

SDS — 16 sections for chemistry and PPE, with the humility to verify by monitoring.

Instruments, container behavior, and the full ERG skillset come next. If this layer is wrong, those layers inherit the error.