Study guide

13.1 Routes of Exposure

Hazardous Materials Technician Certification Exam

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Overview

1.1 Current Exam Facts 1.2 Technician Role and Response Levels 1.3 NFPA 470, OSHA HAZWOPER, and APIE-T

2 Hazard Identification Systems

2.1 DOT Hazard Classes 1–9 2.2 Placards, Labels, and GHS Pictograms 2.3 UN/NA Numbers and NFPA 704 2.4 SDS and Shipping Papers

3 Reference Sources and Chemical Properties

3.1 Emergency Response Guidebook (ERG 2024) 3.2 Collecting and Interpreting Hazard Information 3.3 Chemical and Physical Properties for Responders

4 Containers, Damage, and Behavior

4.1 Container Recognition 4.2 Container Damage Assessment 4.3 Predicting Material and Container Behavior 4.4 Estimating the Endangered Area

5 PPE Ensembles and Chemical Protective Clothing

5.1 EPA/OSHA PPE Levels A–D 5.2 Chemical Protective Clothing Types and NFPA Standards 5.3 Permeation, Penetration, Degradation, and Compatibility 5.4 Respiratory Protection: SCBA and Air-Purifying Respirators

6 PPE Selection and Operations

6.1 Selecting Technician-Level PPE 6.2 Donning, Doffing, and Working in PPE 6.3 Heat Stress, Work/Rest, and the Buddy System 6.4 PPE Programs and Medical Surveillance

7 Decontamination Fundamentals

7.1 Contamination vs Exposure 7.2 Emergency Decontamination 7.3 Technical Decontamination and Corridor Setup 7.4 Decontamination Methods and Solutions

8 Mass Decontamination and Effectiveness

8.1 Mass Decontamination 8.2 Equipment Decon and Runoff Control 8.3 Evaluating Decontamination Effectiveness

9 Product Control Fundamentals

9.1 Containment vs Confinement 9.2 Confinement Techniques 9.3 Plugging and Patching 9.4 Overpacking Nonbulk and Radioactive Packages

10 Offensive Control and Rescue

10.1 Pressurized Containers and Chlorine Kits A/B/C 10.2 MC 306/DOT 406 Dome Clamp, Grounding, and Bonding 10.3 Liquid Product Transfer 10.4 Victim Rescue and Recovery in the Hot Zone

11 Air Monitoring Fundamentals

11.1 Monitoring Strategy, Bump Tests, and Calibration 11.2 Four-Gas Meters and Combustible Gas Indicators 11.3 Photoionization and Flame Ionization Detectors

12 Specialized Detection

12.1 Colorimetric Detector Tubes 12.2 Radiation Types and Detection Instruments 12.3 Interpreting Monitoring Data and Instrument Limits

13 Toxicology Fundamentals

13.1 Routes of Exposure 13.2 Dose-Response, Acute vs Chronic Effects 13.3 Exposure Limits: PEL, TLV, STEL, Ceiling, IDLH, REL

14 Health Effects and CBRN Hazards

14.1 Chemical Health Effects and Target Organs 14.2 Biological Hazards and CBRN/WMD Agents

15 Incident Command and Site Control

15.1 ICS Structure for Hazmat Incidents 15.2 Control Zones and the Site Safety Plan 15.3 Incident Action Plan and Response Objectives

16 Evaluation and Termination

16.1 Evaluating and Reporting Progress 16.2 Termination, Documentation, and Evidence Preservation

13.1 Routes of Exposure

Key Takeaways Explain This Topic AI

OSHA 29 CFR 1910.120(q)(6)(iii)(I) requires technicians to understand basic chemical and toxicological terminology and behavior, including how a product actually enters the body.

Inhalation of vapors, gases, aerosols, and dusts is the most common occupational route; it is also the fastest way a failed self-contained breathing apparatus (SCBA) becomes a medical emergency.

Skin absorption is a real technician hazard for lipid-soluble products — pesticides, phenol, hydrofluoric acid (HF), and nerve agents — even through intact skin and through a pinhole in a glove.

Ingestion is usually a hygiene and rehabilitation-area failure (contaminated hands, eating or drinking in dirty CPC, off-gassing suits); injection is sharps, high-pressure product, or contaminated trauma; the eyes are a separate mucous-membrane route.

Match the route to the control: inhalation → respirator; skin → chemical protective clothing (CPC); ingestion → decontamination and hygiene; injection → puncture-resistant protection and medical care; ocular → facepiece or chemical goggles.

Last updated: August 2026

13.1 Routes of Exposure

Quick Answer: A hazardous materials technician stops a release and keeps the product out of people . Occupational Safety and Health Administration (OSHA) 29 CFR 1910.120(q)(6)(iii)(I) requires you to understand basic chemical and toxicological terminology and behavior . Start with the route of exposure : inhalation , skin absorption , ingestion , injection , and ocular . Inhalation of vapors, gases, aerosols, and dusts is the most common occupational route . Match the route to the control: respirator for air, chemical protective clothing (CPC) for skin, decontamination and hygiene for the mouth, puncture-resistant protection for injection, and a facepiece or chemical goggles for the eyes.

National Fire Protection Association (NFPA) 470 (2022) does not give toxicology its own Job Performance Requirement (JPR) number, but every Analyze and Plan decision in Chapter 11 assumes you know how the product gets in . Chapter 7.1 already split contamination (material where it should not be) from exposure (a dose through a route of entry ). This section is the route map. If you cannot name the pathway, you cannot pick self-contained breathing apparatus (SCBA) , CPC, or a decontamination method on purpose.

Many first-aid cards list four routes and fold the eyes into “absorption.” Technician items still test ocular contact as its own problem — mucous membranes, splash, and vapor irritation — so this guide treats five pathways. The four-route card is not wrong; it is incomplete for a visor leak.

Five routes, five controls

Route What actually enters Typical field sources Primary technician control

Inhalation Vapors, gases, aerosols, mists, fumes, smoke, dusts Open valves, vapor clouds, displaced confined-space atmospheres, powder dumps Atmosphere-supplying respirator (usually positive-pressure SCBA ) until monitoring says otherwise

Skin absorption Liquid, mist, or vapor through intact or damaged skin; especially lipid-soluble molecules Glove pinholes, soaked inner clothing, prolonged wet contact, permeation of CPC CPC selected for the chemical; glove rings; minimize contact time; skin notation on exposure limits

Ingestion Swallowed product or residue transferred hand-to-mouth Eating or drinking in rehab with dirty hands, chewing gum, contaminated inner gloves, bottles handled with outer gloves Technical decontamination before rehab , no food or drink with contaminated hands, keep dirty CPC out of the rest area

Injection Product forced under the skin or into a wound Sharps at clandestine labs, high-pressure hydraulic or paint injection, jagged metal, broken glass, contaminated trauma Puncture-resistant gloves where the task warrants them; do not treat a high-pressure pinhole as “just a cut”

Ocular Splash or vapor on the eyes and mucous membranes Drum bung spray, wind-driven mist, a leaking visor, rubbing eyes with a contaminated glove Full facepiece (SCBA or respirator) or chemical splash goggles plus face shield as the ensemble requires

The table is a planning tool, not a promise that one control covers every route. Level A exists because some products attack skin and lungs at the same time . Failed SCBA does not make the CPC irrelevant, and a pinhole glove does not make the air clean.

Inhalation — the occupational default

The lungs are a huge, wet, thin membrane sitting on a blood supply. That is why inhalation is the most common occupational route and why OSHA 1910.120(q)(3)(iv) puts positive-pressure SCBA on emergency responders who face an inhalation hazard until the incident commander can show, with air monitoring , that a lower level of respiratory protection will not create hazardous exposures.

What you inhale is not always a “gas” in the textbook sense:

Gases (chlorine, ammonia, carbon monoxide, hydrogen cyanide) occupy the space you walk into.

Vapors ride off liquids (solvents, gasoline, anhydrous-ammonia boil-off).

Aerosols, mists, and fumes carry droplets or solids that still land in the airway.

Dusts (pesticides, metal powders, some oxidizers) are solids you can still breathe .

Heavier-than-air vapors pool in basements, ditches, and sewers; lighter-than-air products collect at ceilings and eaves. Chapter 11 already taught you to put the probe where the product lives. Toxicology adds the reason: the probe location is the inhalation zone you are about to occupy .

A failed SCBA — lost facepiece seal, empty cylinder, bypassed regulator, or a technician who cracked the mask to “talk” — turns the fastest occupational route loose at the highest concentration the scene has. That is not a communications shortcut. It is an inhalation dose .

Skin absorption — pinholes are not cosmetic

Intact skin is a barrier. It is not a vault. Lipid-soluble chemicals dissolve in skin oils and cross . The classic technician list is not trivia:

Pesticides , especially organophosphates and many agricultural concentrates, are built to enter living tissue.

Phenol (carbolic acid) is absorbed through intact skin and can produce systemic toxicity (central nervous system and cardiac effects) with burns that look deceptively modest at first.

Hydrofluoric acid (HF) is both a corrosive and a systemic fluoride poison . Pain can be delayed , especially with dilute solutions, while fluoride binds calcium.

Nerve agents (and related organophosphate military and industrial cousins) are dermal threats , which is why vapor-protective ensembles and tape discipline exist for those entries.

OSHA’s permissible exposure limits (PELs) in 1910 Subpart Z sometimes carry a [skin] notation. That notation means dermal absorption can add a significant dose to whatever you inhale. It is not a fashion footnote. A pinhole in a glove on a phenol or HF job is an exposure pathway , not a laundry problem.

CPC is the dermal control: compatible material, intact seams, correct glove chemical, and contact time short enough that permeation does not win. Chapter 5.3 owns permeation science. This chapter owns the why : skin is a route , so clothing is toxicology equipment .

Ingestion — rehab can poison you without a leak

Adult technicians rarely drink the product on purpose. They ingest residue :

Outer gloves handle a bottle, then the inner fingers touch a sandwich.

Someone “just wets their lips” in the warm zone.

Chewing tobacco or gum in CPC.

Off-gassing of contaminated suits in the rehabilitation area — vapors leaving dirty CPC and putting an inhalation and ingestion problem into the rest area you thought was clean.

The control is boring and non-negotiable : technical decontamination before rehab , no eating or drinking with contaminated hands, bottles and radios that never wear outer gloves, and dirty CPC that does not hang over the cooler. Ingestion is a hygiene failure more often than a product-control failure.

Injection and ocular — small holes, large doses

Injection is not only a needle. High-pressure product (hydraulic oil, paint, some process lines) can inject through intact skin at a pinhole and travel along tissue planes. Sharps at clandestine laboratories, jagged metal on a damaged drum, and contaminated trauma all skip the skin barrier. Treat high-pressure injection as a surgical emergency , not as a bandage stop.

Ocular exposure is splash and vapor. The eye is a mucous membrane with rapid local damage from corrosives and, for some chemicals, a path toward systemic uptake. A full-face SCBA facepiece is an eye control as well as a lung control. Lifting the visor to “see the valve better” is an ocular and inhalation decision.

Scenario: pinhole glove versus failed SCBA

Two technicians finish the same pesticide transfer.

Technician A has a pinhole in a glove . The SCBA never lost positive pressure. Product on the outer glove is a dermal problem: organophosphate skin absorption , possible inner-glove contamination, and a decontamination and medical follow-up issue even if the person “feels fine.” The lungs were protected. The skin was not .

Technician B has intact gloves and a failed SCBA facepiece seal in the vapor. That is inhalation at cloud concentration — the most common occupational route, the fastest dose, and the reason the buddy and the safety officer exist. Washing Technician B’s gloves does not undo the lung dose. Giving Technician A a new cylinder does not undo the pinhole.

If you remember one sentence: name the route, then pick the barrier — respirator, CPC, decon/hygiene, puncture protection, or eye protection — because a pinhole and a failed SCBA are different toxicology events.

Loading diagram... Routes of exposure mapped to technician controls