Study guide
2.5 Physical & Chemical Properties of Hazardous Materials
HAZWOPER 40-Hour Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Regulatory Framework & Safety Program Management (29 CFR 1910.120)
1.1 Regulatory Scope, History & Covered Operations 1.2 Comprehensive Safety and Health Program & Worker Rights 1.3 Site-Specific Health and Safety Plan (HASP/SSHP) Requirements 1.4 Training Mandates & Field Experience Requirements
2 Chapter 2: Chemical Hazard Recognition, Toxicology & Exposure Limits
2.1 Principles of Industrial Toxicology 2.2 Occupational Exposure Limits & Action Levels 2.3 Chemical Hazard Classes & Health Effects 2.4 Hazard Communication & GHS Safety Data Sheets 2.5 Physical & Chemical Properties of Hazardous Materials 2.6 Hazard Information Sources & Field Reference Systems
3 Chapter 3: Site Characterization, Air Monitoring & Environmental Sampling
3.1 Site Characterization Phases & Risk Assessment 3.2 Direct-Reading Air Monitoring Instruments 3.3 Environmental Sampling Protocols & Chain of Custody 3.4 Atmospheric Hazards & Oxygen Deficiency
4 Chapter 4: Site Control, Work Zones & Safe Work Practices
4.1 The Three-Zone Worksite System 4.2 Buddy System & Site Communication Protocols 4.3 Medical Surveillance Program (29 CFR 1910.120(f)) 4.4 Worksite Sanitation, Illumination & Housekeeping 4.5 General Site Safety Hazards & Engineering Controls
5 Chapter 5: Personal Protective Equipment (PPE) & Respiratory Protection
5.1 EPA/OSHA PPE Ensembles: Levels A, B, C, and D 5.2 Respiratory Protection Standard (29 CFR 1910.134) 5.3 Respirator Cartridges, Change Schedules & Fit Testing 5.4 Thermal Stress & Chemical Protective Clothing (CPC) Hazards
6 Chapter 6: Drum Handling, Container Management & Spill Containment
6.1 Drum Inspection, Staging & Handling Procedures 6.2 Shock-Sensitive, Radioactive & Pressurized Containers 6.3 Overpacking, Bulking & Waste Characterization 6.4 Spill Containment, Prevention & Control Measures
7 Chapter 7: Decontamination Protocols & Facilities
7.1 Decontamination Plan Design & Principles 7.2 Multi-Stage Contamination Reduction Corridor (CRC) Layout 7.3 Emergency Decontamination & Heat Stress Decon 7.4 Decon Waste Disposal & Equipment Sanitization
8 Chapter 8: Emergency Response, Incident Command System & Worksite Operations
8.1 HAZWOPER Emergency Response Standard (29 CFR 1910.120(q)) 8.2 Incident Command System (ICS) Structure & Roles 8.3 HAZWOPER Responder Training Levels 8.4 Confined Space Entry, Excavation Safety & Lockout/Tagout
2.5 Physical & Chemical Properties of Hazardous Materials
Key Takeaways Explain This Topic AI
Vapor pressure drives how fast a liquid generates vapor; a liquid boils when its vapor pressure reaches the ambient 760 mmHg.
Vapor density (air = 1.0) predicts whether vapors sink into trenches, sumps, and confined spaces or rise and disperse; estimate it as molecular weight divided by 29.
Specific gravity (water = 1.0) separates LNAPLs that float and are trapped by underflow dams from DNAPLs such as trichloroethylene (1.46) that sink and require overflow dams.
OSHA 1910.106 defines a flammable liquid as one with a flash point at or below 199.4 °F (93 °C), split into Categories 1 through 4 by flash point and boiling point.
RCRA characteristic codes turn these properties into legal waste determinations: D001 ignitability (flash point below 140 °F), D002 corrosivity (aqueous pH at or below 2 or at or above 12.5), D003 reactivity, and D004-D043 toxicity by TCLP.
Last updated: August 2026
Physical & Chemical Properties of Hazardous Materials
Every operational decision on a hazardous waste site traces back to a handful of physical and chemical properties. Whether a vapor pools in a trench or blows away, whether a photoionization detector can see a contaminant at all, whether a spill floats or sinks in a creek, whether a waste stream is legally ignitable — all of it is property-driven. OSHA's suggested 40-hour curriculum (Appendix E to 1910.120, item b(2)) names these fundamentals explicitly: vapor pressure, boiling points, flash points, pH, and other physical and chemical properties. This section is where the numbers on Section 9 of the Safety Data Sheet become field tactics.
Volatility: Vapor Pressure and Boiling Point
Vapor pressure (VP) is the pressure exerted by a vapor in equilibrium with its own liquid at a stated temperature, normally reported in millimeters of mercury (mmHg) at 20 °C or 25 °C. It is the single best predictor of how quickly a liquid will fill a headspace, a drum, or a confined space with vapor.
Anchor yourself to three reference points:
Substance Vapor pressure at 20 °C Field meaning
Mercury ~0.0012 mmHg Barely volatile — but so toxic that even this trace generates an inhalation hazard in warm, unventilated spaces.
Water ~17.5 mmHg The everyday benchmark for "moderately volatile."
Benzene ~75 mmHg Roughly four times water; a spilled drum saturates an enclosure quickly.
Diethyl ether ~440 mmHg Extremely volatile; approaches atmospheric pressure and floods a space with ignitable vapor.
Atmospheric pressure at sea level is 760 mmHg . A liquid boils at the temperature where its vapor pressure equals ambient pressure — which is why boiling point and vapor pressure are two readings of the same underlying behavior . A low boiling point means high volatility at ordinary temperatures. Heat multiplies the effect: vapor pressure climbs steeply with temperature, so a drum that reads clean at 45 °F in the morning can read hundreds of ppm on a photoionization detector at 95 °F in the afternoon sun. This is precisely why staged drums are kept shaded and why air monitoring is repeated across the day rather than once at start of shift.
Where the Vapor Goes: Vapor Density
Vapor density (VD) compares the weight of a vapor to air, with air set at 1.0 . A quick field estimate is the compound's molecular weight divided by 29 (the approximate molecular weight of air).
VD greater than 1.0 — the vapor sinks. It flows downhill, collects in trenches, excavations, sumps, manholes, tank bottoms, and low corners of the exclusion zone. Hydrogen sulfide (MW 34, VD ≈ 1.19), gasoline vapor (VD ≈ 3-4), and most chlorinated solvents behave this way. Monitor at the breathing zone and at ankle level and at the bottom of any excavation.
VD less than 1.0 — the vapor rises. Methane (MW 16, VD ≈ 0.55), ammonia (MW 17, VD ≈ 0.59), and hydrogen accumulate at ceilings, under tank domes, and at the top of confined spaces. Monitor high.
The classic fatality pattern on hazardous waste sites is a worker descending into an excavation or vault where a heavier-than-air asphyxiant has silently displaced the oxygen. Vapor density is the property that predicts it.
Where the Liquid Goes: Specific Gravity and Solubility
Specific gravity (SG) compares a liquid's density to water at 1.0 :
SG below 1.0 — a Light Non-Aqueous Phase Liquid (LNAPL). Gasoline (≈ 0.72-0.76), diesel, and most fuel oils float as a surface layer. Contain them with booms and underflow dams .
SG above 1.0 — a Dense Non-Aqueous Phase Liquid (DNAPL). Trichloroethylene (≈ 1.46), tetrachloroethylene (≈ 1.62), carbon tetrachloride (≈ 1.59), and creosote sink through the water column and pool on the streambed or aquitard. Contain them with overflow dams and recover from the bottom.
Solubility and miscibility decide whether the material forms a separate phase at all. A miscible solvent such as acetone or methanol will not stratify; it disperses into the entire water body, which makes booms useless and forces treatment of the whole volume. This is also why a Coliwasa sample from a drum of an immiscible mixture shows visible layers while a miscible mixture looks uniform.
Ignition Properties
Flash point is the lowest temperature at which a liquid gives off enough vapor to form an ignitable mixture near its surface. It is a vapor property, not a liquid property — a puddle below its flash point will not sustain ignition because it is not generating enough vapor.
Autoignition temperature is the temperature at which a substance ignites spontaneously with no external ignition source . It is typically hundreds of degrees above the flash point, and it is why hot exhaust manifolds and hot work surfaces are ignition hazards even where no spark is present.
Flammable range — the span between the Lower Explosive Limit and Upper Explosive Limit — is covered in Section 3.4 and is read directly by combustible gas indicators.
Since the 2012 Hazard Communication alignment, 29 CFR 1910.106(a)(19) defines a flammable liquid as any liquid with a flash point at or below 199.4 °F (93 °C) , sorted into four categories:
- Category Flash point Boiling point Typical example
- 1 Below 73.4 °F (23 °C) At or below 95 °F (35 °C) Diethyl ether, pentane
- 2 Below 73.4 °F (23 °C) Above 95 °F (35 °C) Gasoline, acetone, toluene
- 3 At or above 73.4 °F (23 °C) and at or below 140 °F (60 °C) — Kerosene, mineral spirits
- 4 Above 140 °F (60 °C) and at or below 199.4 °F (93 °C) — Many heavier fuel and lubricating oils
- Reactivity Properties Worth Flagging on Sight
Water-reactive materials (sodium and potassium metal, calcium carbide, acid chlorides, acid anhydrides, sodium hydride) generate heat and often flammable gas on contact with water — never apply a water stream, and store them in covered dry bays.
Pyrophoric materials ignite in air within seconds without any spark.
Oxidizers supply their own oxygen and will drive a fire in a segregated flammables area; segregate them physically, never merely by labeling.
Polymerization hazards — monomers such as styrene or vinyl chloride whose inhibitor has been depleted by age or heat can run away exothermically inside a sealed drum, which is one mechanism behind the bulging drums covered in Section 6.1.
Ionization Potential: The Property That Decides Whether You Can See It
Ionization potential (IP) , measured in electron volts (eV), is the energy required to strip an electron from a molecule. A photoionization detector can only detect a compound whose IP is lower than the lamp's eV rating . Methane (IP 12.6 eV) is invisible to every standard PID lamp; benzene (IP 9.24 eV) is detected by all of them. Whenever you plan monitoring, look up the IP in Section 9 of the SDS or the NIOSH Pocket Guide before you choose the lamp — this is the property that determines whether "zero on the meter" means "clean" or means "wrong instrument."
From Property to Legal Waste Code
These properties are not academic: RCRA converts them directly into waste codes that dictate disposal cost and paperwork.
RCRA characteristic Code Property threshold (40 CFR 261.21-261.24)
Ignitability D001 A liquid (other than an aqueous solution containing less than 24% alcohol by volume) with a flash point below 60 °C (140 °F) ; also ignitable compressed gases, oxidizers, and certain ignitable solids.
Corrosivity D002 An aqueous waste with pH at or below 2 or at or above 12.5 , or a liquid that corrodes SAE 1020 steel faster than 6.35 mm (0.250 inch) per year at 55 °C .
Reactivity D003 Normally unstable, water-reactive, capable of detonation, or generating toxic gases when mixed with water or at pH 2-12.5 (cyanide- and sulfide-bearing wastes).
Toxicity D004-D043 Leachate from the Toxicity Characteristic Leaching Procedure (TCLP) exceeds the regulatory level for a listed contaminant.
When you run a HAZCAT screen in the field (Section 6.3), you are measuring these same properties with paper strips and spot plates so that drums can be segregated hours or weeks before the laboratory data arrives.